Blinking lights but not coming on
Laptop, about a year old
Was working great, have not used it in over a week and was plugged in the
entire time.
Went to turn it on last night and NOTHING
Two lights on panel are blinking faintly: power and Battery. What is
most likely the problem?
Then the power control circuitry on the system board has likely failed. Time to get it diagnosed/repaired by a Toshiba Authorized Service Provider (ASP). Find one from the list at http://pcrepair.toshiba.com
If the system is not still under warranty, be sure to get an estimate for the repair, as it may be more than the cost of a new notebook.
Similar Messages
-
Cisco 4503 "1000BaseLH" SFP light is not coming ---- Urgent
Dear Team,
I have Cisco 4503 and I have inserted 1000BaseLH and light is not coming up but for 1000BaseSX its fine.
Please suggest.
CORE#show int GigabitEthernet1/18
GigabitEthernet1/18 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 001e.4aa6.b891 (bia 001e.4aa6.b891)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, Auto-speed, link type is auto, media type is 1000BaseLH
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
CORE#show inventory
NAME: "GigabitEthernet1/18", DESCR: "1000BaseLH"
PID: TRF5735AALB202 , VID: A1 , SN: OPA11241478
Thank You,
Abhisar.Dear Reza,
we connected cable and it came up. The conclusion is single m9de sfps does not show light where multimode sfp shows light when sfp is connected on switch port.
Thank you for your suggesion.
Thank You,
Abhisar. -
MacBook pro not charging. Charging light is not coming up
My Macbook pro's battery was down to 2% so I shut it down and kept in for charging. But the charger's green light or the orange light indicating charging didn't come. I checked the power supply and it was fine. The charger has the slight hum indicating it is getting the power but macbook is not charging and the lights are not coming on. My Macbook is a late 2011 model of 13"
Hi chaitanya.ac,
I would see if this article helps narrow down where the problem is or perhaps even resolve it:
Apple Portables: Troubleshooting MagSafe adapters
http://support.apple.com/kb/ts1713
Best,
- Ari -
Cisco 4503 "1000BaseLH" SFP light is not coming
Dear Team,
I have Cisco 4503 and I have inserted 1000BaseLH and light is not coming up but for 1000BaseSX its fine.
Please suggest.
CORE#show int GigabitEthernet1/18
GigabitEthernet1/18 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet Port, address is 001e.4aa6.b891 (bia 001e.4aa6.b891)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, Auto-speed, link type is auto, media type is 1000BaseLH
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
CORE#show inventory
NAME: "GigabitEthernet1/18", DESCR: "1000BaseLH"
PID: TRF5735AALB202 , VID: A1 , SN: OPA11241478
Thank You,
Abhisar.Thanks Marvin,
It is solved.
https://supportforums.cisco.com/discussion/12464296/cisco-4503-1000baselh-sfp-light-not-coming-urgent
Thank You,
Abhisar. -
IO assigned with Asset,but not coming at the time of PO creation
Hello
IO assigned with Asset,but not coming at the time of PO creation.
I have made following settings:
1 Depreciation - IFRS (INR) 1 0L
15 Income Tax Act 0
20 Depreciation - Indian GAAP (INR) 3 1L
30 Depreciation - IFRS (USD) 0
31 Depreciation - Indian GAAP (USD) 0
In ACSET-Account assignment:
for dep area-20
CAUFN Internal Order * Generic Trans. Type 02 Depreciation Run
KOSTL Cost Center * Generic Trans. Type 02 Depreciation Run
so currently i am using only dep area-20 only(Indian GAAP)
CAPEX budgeting is through IO. AUC is not doing through IO,its directly from AIAB/AIBU
AS01
KO01
AS02
KO22
KO30
so what is the problem,why i am not getting IO (which is in display mode in PO) when assigned the Asset with category of "A" (asset) in PO.......when i assigned Asset- the GL account come automatically but IO didn't come.
kind regardsHey Ajay
thanks for your reply.....
now i'm getting new error:
Parallel depreciation area 31 is not posted
Message no. AA565
Diagnosis
The asset to be posted does not manage parallel depreciation area 31, or
transaction type that you are using is limited to certain depreciation
areas, and does not contain depreciation area 31. This is incorrect.
System Response
Posting is rejected.
Procedure
Check the asset and the transaction type.
I have checked some configuration but not able to debug it.
regards -
0fi_ar_4 netduedate(netdt) value coming in RSA3 but not coming in BI PSA
Hi all,
i am using 0fi_ar_4,
netduedate(netdt) value coming in RSA3 but not coming in BI PSA, in BI PSA there is 10-12 do cument there where netduedate is null while for same document we are getting the netduedate running from transaction RSA3, how?
Thanks.Hi,
I found the problem, i have write a user exit in data sourc e in ecc, i am getting value in rsa3 but not getting in BI PSA becaue ise there is 20000 KB limits for per info package load request i.e. idoc size, as its fixed, i did change little in my user exit at ECC.
thaks -
My c700 laptop power light is not coming on. what can i do to resolve this issue?
My c700 laptop power light is not coming on. what can i do to resolve this issue?
Will it read audio CDs? (In other words, is it just a problem with DVDs, or are CDs not read, either?)
-
I downloaded a movie from itunes and it finished but not coming up in movie folder what do i do??
it should be under (using Finder):
[user folder] > Music > iTunes > iTunes Music > Movies -
3 blinking lights,but I changed ram
and my mac still wont boot up. It keeps giving me the three blinking lights (which supposedly means incompatable ram). My ram had been in there for a couple years at least. So I took them out and re-installed them in one pair increments. Still got the problem, so I bought new ram and it still has the problem. So it seems to think that the ram is bad. anyone else experience this? Oh, right before it happened, my fans ran light a jet plane.
Same here
Added 2x 1GB ram and now the most inner slots are permanent void (with banks inserted)
AHT reports error post/0/2048 and NVRAM reset does not fix situation.
I've tried all possible permutations with or without new ram,
with or without old ram,
with 2,4,6,8 strips per time (my fingers are boiled)
the config is (internal from external slots):
2x 512MB (original Apple present but not recognized)
2x 512MB (S3+, 4 years works perfect)
2x 1024MB (Kingston, 3 years works perfect)
2x 1024MB (Kingston VR, new)
Total of 5GB ram
Since I've moved the originals ones, the most inner slots are missed.
All banks of ram seems to be good in others positions.
I hope in a firmware error.
I don't want to think about slot damage. -
Hello,
I inserted a new DVD in my mac book pro, its working and the drive is reading the dvd but unfortunately is not coming out. I have tried several ways mentioned on all over the net and apple community websites but nothing has worked so far.
I need a easier and manual way to eject the DVD. Where is apple's help?
Please help me. This is one of the weaknesses Apple should work on because it is causing us pain and loss of efficiency which is not apple's quality.
ThanksThanks for asking, actually I just found a trick on a website.
It siad that restart MBP while holding eject button, I did it and DVD came out right away.
I hope that this works out for everyone.
But still there is a need for a manual eject system so that people don't worry about stucking the DVD or CD in th drive.
Thanks anyway dear. -
IDOC in 03 staus but not coming to PI system..
Hi Experts,
I am working on IDOC to IDOC scenario.All of the IDOCs are in 03 status in R/3 system but some of the IDOCs are not coming to PI system.I checked SM58 also but its fine.
Should it be in 12 staus?
Is it possible that IDOC in status 03 can reach to the target system?
Please reply it asap.Its urgent.
Regards,
VikramHi Vikram,
First of all, bd75 is only for status conversion. This means, that only IDoc statuses are changed, based on the status of the RFC call. IDocs are not despatched again by this transaction.
Secondly, you might want to check the EDI Port that is assigned in the partner profile, if it is pointing to the correct target system.
Finally, if target system is OK and you don't find anything in sm58 in sender system, then you should go to smq2 in PI and you should find your IDocs there, waiting in a blocked queue.
Hope this helps,
Greg -
Graph is coming when running thru desktop but not coming thru PIA
HI all,
I have an issue. I have created a XMLP template which generates a Chart.
When i run the report in desktop, chart is coming .
but when i run through peoplesoft PIA chart is not coming.
Kindly please suggest me how can i see the chart.
Many thanks in advance.
Regards,
Dhaya.Go to www.blackberry.com/blackberrylink for the latest version.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you! -
Data available in RRP3 view but not coming in SNP planning book
Hi All,
I am facing an issue in SNP book. I can see forecasts in RRP3 view. But when I load the same data in SNP planning book, the forecasts are not coming there (forecast KF)
I ran LC Cons check, PA cons check, OM17, but still the same result.
Any pointer would be highly valuable.
Regards,
Manotosh BhattacharyaHi
If you look at the standard Forecast KF 9ADFCST in your planning area, it is usually assigned the Category Group of DF1. This category group only contains the category FA for forecast. If you create Forecast in /SAPAPO/RRP3, this will create Additional Forecast or category group FC. Therefore any forecast generated this way will not appear against the standard planning book KF.
So you have two choices, if your forecast is only FC category then use the KF 9AAFCST Forecast (Addittional) in your data view or create a new Category Group with both FA and FC assigned to it and then assign this Categotry Group to 9ADFCST in your planning area.
Regards
Ian -
For quite a while now I have missed some important emails that have come through to my iphone but not downloaded to my iMac, its happening more and more recently. It is really fustrating, I have looked at my iMac and can't find anywhere to adjust the settings to let through the missing emails, the emails that are not coming to my home pc are normaly from large companies, some from my credit card company and comformation for hotel bookings etc, etc.
Can anyone help me please?Problem might me with how your e.mail is set up if you're using POP3.
If you're using POP3 then you need to add "recent:" (without the quotation marks) before your username on both your iMac and your iPhone.
I use POP3 with Virgin Media and they have well documented help on this aspect.
This now works fine for me and I no longer miss any e.mails. -
HT201209 reedemed code on iphone but not coming through on ipad
I have reedeemed itunes card on my iphone but it is not coming through on my ipad, which is same apple id it usually does.
Apple has a pretty comprehensive trouble shooting guide in Mail Setup, Troubleshooting etc..
Maybe you are looking for
-
I have a weird problem that I have never experienced before. I'm using Captivate 4. I have back and next buttons configured for the user to advance the slide. Both buttons have "pause after". I have various text fade in/out coming up on the screens,
-
Game Center won't launch (Mavericks 10.9.5)
Game Center isn't launching. When I enter my Apple ID and password and it appears to authenticate but never completely logs me in. ( I know its authenticating because if I enter the incorrect password it throws an error.) If I try to launch a game
-
Daqmx Configure Logging with Time Stamp
Hi All, I was wondering if it is possible to use Daqmx Configure Logging to log both data, and a row of the exact time (not a relative one), or at least add the FIRST time and date to the information? Thanks, Lester
-
when a language will be called high level language ? is it true if the language support graphics then it is high level ? or what are the characteristics should a language posses to be called high level ? Fortran ? is it high level ? in fact i dont kn
-
Is there a manual for Lion Server?
Where can I find detailed documentation for Lion Server?