Blu-ray Error: "not enough fre storage". Code:"25", Note "Not enough space on media"

I have a project a Encore CS6 V6.0.1.013 for MAC.
I tryng export do Blu-ray Disc, but ireceved this error message
Blu-ray Error: "not enough fre storage". Code:"25", Note "Not enough space on media"
But at "Disc Info" i have 14.71mb free

My longer notes on this error:
The most common workaround for this is to build to a folder and burn with ImgBurn (for PC) or toast (for Mac).
Searches show that there has not been success in many situations. I do not believe that it is one problem.
I have generally believed that the error refers to temporary storage on the hard drive. And users underestimate the amount of temporary hard disk drive space used. For bluray it is about twice the disk or more.
Some users experience this error when they are creating dual layer BD disks, and a layer is more than 25G. Each video/layer must fit on one side.
And some users successfully burn their disk by re-encoding to a lower bitrate (a 25G BD disk does not hold 25G). Encore uses padding to predict the size on disk (e.g. add 10% to the amount of space it predicts that build will use), and it can be wrong.
Always good to "run as administrator, though I don't know that ever fixed this issue if someone wasn't.
For CS4 there was a required update for a Roxio component. I believed this was a temporary problem due to the combination of Win7 and Encore CS4, but users on newer OS and Encore have reported resolution of problems after installing the patch.

Similar Messages

Blu-ray Error: "not enough free storage" - even though 800MB are free

I'm trying to burn a Blu-Ray, about 2h20min worth of VBR 2pass HD video exported therough Premier 5.5 via the "Queue" (Media Encoder). Using the Blu-ray mpeg preset with the target bitrate slightly reduced.
Anyway, point is that Disc Info in the Build tab says 24.18 GB used, 818.9 MB free, yet when I go to burn I get "Blu-ray Error: 'not enough free storage', Code '25', Note: 'Not enough disc space.'" I've had problems with dual layer DVDs in the past, but I have successfully burned blu-ray before (but with not as much content). So I tried doing my workaround for DLs, which is burning to a folder with the intention of going through ImgBurn. But when I try to do a Blu-ray folder I get 'Blu-ray Error: 'device not ready,' Code '3', Note: "File can not open.(F:\Encore Projects\Geprges and Julie Bluray\AuthorScriptHDMVSessions\Gerpges Julie export 1 bluray 2pass high.m2v.00_28_02_22.9.2011_UTC_04_00DST.ves.)- "
("Georges and Julie" is name of my file and project.)
Any ideas? For the record, yes I am running as administrator.

Well, this is a bug that has been running since, I think, CS5 and is still there in CS5.5
This error code 25 would come when you burn to the Blu-ray Image and not with Folder and Disc.
And regarding the error code 3 that came while burning to folder, this is because sometimes with multiple burning attempts of the same project causes the session files of the project go corrupt. So FIRST TAKE A BACK UP OF YOUR PROJECT (save as your project to some other place to retain a copy of it) and then clsoe the project and delete all the session files from the project folder. Delete the session files and Not the Sesson folder.
Reopen the project and build. This should work.

Blu-ray Error: "not enough free storage", Code: "25", Note: "Not enough space on media

Okay, I have been able to get around issues on making a number of BR images. But, this one makes no sense.
This is a 2 hour project. I get the above error when it hits the end of the building discimage at 31.82 of 31.82.
The media choice is 50 gig. My c drive has 250 gig free. My project disc has 300 gig free. My audio files are a few frames smaller
than the video. (Which had caused me issues in the past)
About the only thing different in this project is I have 6 slide shows.
Not sure what else to try.
Dave

MAYBE SIMILAR PROBLEM ?
I might suffer from another consequence of (this) bug - I have experienced a very strange situation in EnNCORE CS5 - preparing three individual episodes as three individual Blu-ray images (around 8GB each) - combining these into a single Blu-ray (50GB) media - the resulting image turns out to be around 33GB - 35% larger than the sum of the three individual episode disks - please refer to the table below:
Episode   Transcoded(KB)      Estim.(GB)      Result(KB)
1                       7.850.387     9,16               8.240.064
2                       7.776.599     9,08               8.163.648
3                       7.808.916     9,23               8.300.928
Artihmetic sum 23.435.902     27,47             24.704.640
ENCORE         23.435.902     27,40             33.305.300
What are these eight million KB used for ??? 8.600.660
All four disks were produced as IMAGES - source files transcoded by the H.264 Blu-ray preset in the Media Encoder - and all four Blu-rays without any menu-structure - plain "firstplay" setup. It seems to me that ENCORE adds up some huge amount of "garbage" - however the 33GB image did play OK.
Niels

Blu-ray Error Code 25 Note: Not Enough Hard Disc Space

I'm trying to make a Blu-ray image on my computer and recieving an error that states:
Blu-ray Error
Not enough free storage, "code 25" Note: Not enough Hard disc space
Now I first thought to check my hard drive but I have plently of space. Next I noticed that encore CS3 was trying to make an image that is 340GB in size!!! Why would it do that? My project only has 4 assets. HELP this is going from bad to worse.

My longer notes on this error:
The most common workaround for this is to build to a folder and burn with ImgBurn (for PC) or toast (for Mac).
Searches show that there has not been success in many situations. I do not believe that it is one problem.
I have generally believed that the error refers to temporary storage on the hard drive. And users underestimate the amount of temporary hard disk drive space used. For bluray it is about twice the disk or more.
Some users experience this error when they are creating dual layer BD disks, and a layer is more than 25G. Each video/layer must fit on one side.
And some users successfully burn their disk by re-encoding to a lower bitrate (a 25G BD disk does not hold 25G). Encore uses padding to predict the size on disk (e.g. add 10% to the amount of space it predicts that build will use), and it can be wrong.
Always good to "run as administrator, though I don't know that ever fixed this issue if someone wasn't.
For CS4 there was a required update for a Roxio component. I believed this was a temporary problem due to the combination of Win7 and Encore CS4, but users on newer OS and Encore have reported resolution of problems after installing the patch.

Blu-ray Dual layer code 25 "not enough space on media"

Using Encore CS6 (Cloud edition) to build Blu ray Dual Layer on Mac. Project is 34.75 GB. While building Blu-ray Image all is well until Data written 34.75 GB of 34.75 GB. Then the dreaded "Blu-ray Error: "not enough free stoarage", Code: "25", Note: "Note enough space on media" comes up and the buld is stopped. I repeated by building a new project with the same results. There is over 100 GB of free space on the hard drive. I paritially rebuilt the project at 22.5 GB and tried it as a single layer image. Everything worked fine for that Blu-ray image, so it appears this could have something to do with the Dual layer nature of the larger project. Any help and guidance would be much appreciated.

I would point out three points. You can try them in order:
You can apply the 6.0.2 patch that is available (if you have not done so) because the patch has a fix around this issue.
There is a lot of space requirements for the dual layer BD project. Here is the list of almost all the things that would need space:
First the asset's indexed files would need space. For audio files, there might be conforming happening that again would need space.
Then when yoy build the project, the assets will be transcoded (if already not or they are not Don't Transcode). This would take a considerable amount of space as the transcoded assets are complete footage which would be huge.
Then while creating a image file, First all the files (muxed video streams) would be copied on the disc in a folder (generally named BDMV) and then at the final step, they would be copied from the BDMV folder to the iso file and finally the BDMV folder would get deleted. So this step would need almost double the size of your project. IF your project is say 35 GB, then this step alone would take more than 70GB.
So the space requirement for a 35 GB (Disc Info) project might go to almost 100 GB.
But again there is some bug in size estimation for Motion menus and slideshows. Encore says that they will occupy lesser space but actually they are going to occupy more space. So if your project has motion menus or slideshow, then the estimation might be incorrect. So if it showing 35 GB (for example) and your project has motion menu or slideshow, then actually it might be 37GB or more or anything greater than 35GB depending on the slideshow and motion menu duration in the project.
-Ramesh.

Has anyone sloved Blu-ray Error 25?

Hello,
I am trying to author a Blu-ray DVD and When it comes time to burn I get the following error message:
Blu-ray Error: "not enough free storage", Code "25", Note: "Not enough disc space.
I've serached on these forums and it appears that no one has posted a solution. I've spent about 3 hours on the phone with Adobe technical support and so far they seem to know less about this error than I do. Please help!
-Alan Lockwood

Just another try: the firmware "this unknown".
Just minutes ago I was trying to burn a data CD.
I burned (really BURNED!!!!!!!) 3 CDs without success: it failed all the time.
Tried with other softwares: same result!!
So I went to Pioneer website and downloaded latest firmware that ALREADY I'VE INSTALLED (dated back to July 2008).
Bingoo!! All the two BD writers works great with CDs.
Sometimes some drivers go corrupted by misterious operations (registry data cleaner first (very unuseful)).
So another challenge Vs bad luck could be a refresh.
Obviously, Steph, this is not your case, sorry.
Hope this helps
Ciao
Giorgio

Blu-ray error: "device error", Code "3", Note: "AS_StorageError = -97064

Hello,
I am becoming increasingly frustrated with Encore as it now seems that I cannot burn a bluray to a disc. I would love to be able to talk to someone in support at Adobe but that does't seem to be an option. I have attempted to burn a video that is 18.45GB (transcoded) to a 25GB BD-R disc with the following error received on both attempts:
"Blu-ray error: "device error", Code "3", Note: "AS_StorageError = -97064"
I don't understand this error because there should be plenty of room on the disc? I also had an issue a few weeks ago with Encore preventing me from burning a 20.4GB transcoded movie onto a 25GB disc. This may be unrelated and I am aware of the issues in Encore regarding the calculation of file size, but why am I now experiencing issues all the sudden?
My configuration:
Mid-2012 MacPro
OSx 10.8.5
Adobe Creative Suite CS5.5 (Encore CS5.1)
Internal MCE Technologies Blu-ray burner
I appreciate any help and support!!

The Code 3 AS_StorageError comes in many variations.
Google: encore "AS_StorageError=-97060" and you'll find a bunch issues. Now replace the 97060 with your specific code (97064) and you'll see there are no finds other than your thread.
These all appear to have physical storage, hard drive, or media issues. Keep in mind that for Blu-ray especially, Encore uses a huge amount of temporary storage.

Adobe CS5 error Build .iso - Blu-ray Error: "device error", Code: "3", Note: "File can not o

Hi am trying to create a bluray image .iso i loaded the gritty submenu and modified it and am getting this error
and when i try to build it it giving me this error
Blu-ray Error: "device error", Code: "3", Note: "File can not open.(/Volumes/Mac HD1/Adobe Encore Projects/BD/AuthorScriptHDMVSessions/Gritty Noir Submenu HD_mm_1.m2v.00_00_00_1.1.1_UTC.ves) -
Anybody encountered this problem? Thanks I appreciate it.

Hi,
Remove the all the files from
/Volumes/Mac HD1/Adobe Encore Projects/BD/AuthorScriptHDMVSessions/
This will resolve this issue.
This happens if any file corrupted in Volumes/Mac HD1/Adobe Encore Projects/BD/AuthorScriptHDMVSessions/ folder
Thanks,
Pankaj Gauba

Blu-ray Error: "device error", Code "3", Note: "CreateStcSequence: Fail to write M25 File.

I keep getting this error message about 11gb into burning a 22gb Blu-ray. "Blu-ray Error: "device error", Code "3", Note: "CreateStcSequence: Fail to write M25 File." I have tried just about everything from running as administrator, starting a new project and changing the disc too. I am using CS6 and going crazy... any ideas?

Hi,
First try to create Bly Ray Image Under option 'Output" Select BluRay Image, and also select the destination to create Image and click on Build, It will create a BluRay Image with extension of .iso. Now to burn BluRay Disc, you need to Select BluRay Disc under 'Output' Option and Below under 'Source' Option select BluRay Image instead of current project and Select the destination where you have put .iso Image, Then click on Build and it will burn BluRay disc.
In simple , First create an Image then Burn that image to BluRay .
I hope, it will help you.
Thanks

Blu-ray error:"file already exists", code "6" , Note : 118240 11771552 11826176

It has been a 3 days that i have try to make Blu-ray .ISO image on Encore CS5, i always have that message: Blu-ray error: "file already exists", code "6" , Note : 118240 11771552 11826176. Everything seems to work fine before.
Windows 7 Ultimate 64bit,
Intel Core i7-2600K Sandy Bridge 3.4GHz,
CORSAIR CWCH50-1 High Performance CPU Cooler, ASUS P8P67 PRO,
G.SKILL Ripjaws X Series 16GB,
EVGA GeForce GTX 460 (Fermi) 2GB ,
Matrox MXO2 with MAX,
COOLER MASTER HAF 932 Black ATX Full Tower Computer Case,
Adobe CS 5 Production Premium
thanks in advance

Thank you ram8kumar. I will answer step-by-step, as you did:
- there is no subtitle in the project
- .PSD file is not to large, 2 files 1920X1080 and only 2-3Mb, and they only used as menu (I did this a milion times before), there is no slideshow in the project
- Disc name is not blank
- there is no sledeshow (burning a slideshow with no pan and zoom or with no transition with H264 settings)
Lest two might be the problem.
- I exported .h264 files from PPro CS5 with Matrox MXO2 Mini with MAX, Matrox preset and if I remember right target was 30Mb/sek
- Audio and video track duration in the timeline was 1(one) frame difference.
Thank you agan, and I will post the results as soon as I will get done with it.
Vladymyr.

Blu-ray Error: "device error" Code: "3", Note: "AS-StorageError = -97060

I just wasted 2 Blu-Ray discs trying to burn a project. I was trying to burn a very simple project: a two-chapter Blu-Ray with two 55 minute episodes of a TV show on it. I have used the exact same computer recently to do exactly the same job with success, so I don't know what the problem is.
There are no menus in the project: it's just a bare-bones auto play disc with stereo sound only. The disc shows 24.37 GB used on a single-layer BD.
The files are conformed and as the build begins, the following error pops up:
Blu-ray Error: "device error" Code: "3", Note: "AS-StorageError = -97060
System info:
Windows 7 Professional
Service Pack 1
Intel i7 8 cores @ 2.80 GHz
12 GB 1600 RAM
AMD Radeon HD5870
WD 3TB HD 7200 RPM NTSC file system
Pioneer BD-RW BDR-206 ATA burnerncore
Adobe Encore CS6

I do not see another example of this error with the "97060" in it.
I never trust my recollection of this, but note that the 24.37 GB may actually be 24.37 GiB, which may be too big to fit on a single layer Bluray. You should get a different error, but who knows.
I would try building to a folder to see if that succeeds. Then you can return to the issue of burning. Many of us prefer ImgBurn for burning rather than Encore.

Blu-ray Error:'fatal error", Code:"6", Note: "Empty palette in IG composition.

If i try to burn or create an ISO I get this error.
Blu-ray Error:'fatal error", Code:"6", Note: "Empty palette in IG composition.
Any one have an idea what this means?
Maik

Fixed!
I had a broken /incomplete button in a menu. After replacing it with a new button everything worked.
Maik

Encore CS4 Blu-ray Error: "Fatal Error", Code: "0", Note:''

Has anyone encountered this: Encore CS4 Blu-ray Error: "Fatal Error", Code: "0", Note:''
Any ideas on what it means or how to fix it?
Burning to a BD-R. Tried two different Blu-ray burners. Created a Blu-ray Image first.

For CS4 you must update the Roxio component http://forums.adobe.com/thread/400484?tstart=0
More on Encore and Roxio http://forums.adobe.com/thread/528582?tstart=0 or direct to
http://kb.roxio.com/search.aspx?URL=/content/kb/General%20Information/000070GN&PARAMS
Also, Long File Names or odd characters Cause Crashing http://forums.adobe.com/thread/588273
And #4 Here http://forums.adobe.com/thread/666558?tstart=0
And This Message Thread http://forums.adobe.com/thread/665641?tstart=0

Blu-ray Error code 25

I am trying to burn a Blu-ray DVD the disc Info says 6.56 is used and 18.44GB is free. I am using a 25GB sony Blu-ray DVD. The error code says there is "not enough free storage", Code:"25", Note: "not enough hard disc space".
Is this a problem with the DVD or my computer.
The external hard drive where the rest of the file is for this project only has 1.92GB available. Is this my problem?
Thanks
ms

I'm posting this even though it may sound like a 'duh' comment.
I was trying to burn my first Blu-Ray DVD on a new BD-RE (rewritable disc), and I was getting a "not enough free storage" Code "25" error. I knew file sizes were not an issue, as my test DVD was less than a gig, and I have over 300 GB free on my hard drive.
The problem: Rewritable DVDs need to be formatted before they can be used.
You may go 'duh!' but that's one of those things that is clear only when known. Now I know.

Blu-ray Error Code 0

I am trying to burn a Blu-ray disc from a Blu-ray image I made in Encore CS3 and it returns a Blu-ray Error Code 0 Note "". No idea what the problem is.
I am using the Sony BWU-200S burner with Imation's 25GB BD-R with AquaGuard. The Encore project shows that there is 4.32 GB free on this project, 20.68 used.
Any ideas?
I tried the xml parser install but it says my Windows XP SP2 system already has a higher version.
I verified the project settings are using a preset. I exported the video from Adobe Premier Pro CS3 using a Matrox Axio export preset. It's 1440x1080i video.

After a little more toying around, it seems that while the project itself used only 20.68 GB, with the extra information that I guess Encore adds to the disc, it exceded 25 GB by a little. The error was trying to tell me that I exceded the capacity of the BD-R. It would be nice of Encore would show the total capacity of the disc used, whether burning from the project to BD-R or burning from a Blu-ray image to BD-R.

Blu-ray Error: "not enough fre storage". Code:"25", Note "Not enough space on media"

Similar Messages

Maybe you are looking for