Blu-ray with separate 4-pin and 39-pin connector on a new Mac Pro ?

I have a 2007 blu-ray burner I am trying to install as the 2nd drive in my new 12-core Mac Pro. But how to you connect it (it has separate 4-pin power and 39-pin connector) ? Any feedback would sure be appreciated.

The drive is PATA. Older Mac Pros uses PATA optical drives but newer Mac Pros use SATA. There are adapters
<http://www.sonnettech.com/product/tempo_bridge.html>
The adapter was intended for hard drives but should also work with optical drives. You may want to check with Sonnet before buying to see if it works with Blu-ray drives

Similar Messages

  • If i buy a blue ray with a digital copy and if i download the movie on my PC from work, i will be able to download it on my Mac at home later on?

    if i buy a blue ray with a digital copy and if i download the movie on my PC from work, i will be able to download it on my Mac at home later on?

    No, it will be a one use only code. Copy the file onto a memory stick and import it into your library at home later.
    tt2

  • I have a new Mac Pro.  I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro.  How do I set up the old computer?

    I have a new Mac Pro.  I want to use my old Mac Pro as a storage drive for photos and old documents, linked to my new Mac Pro.  How do I set up the old computer?  Both computers have OS X10.9.3.  Currently they are connected by a Firewire 800 cable.

    You certainly could keep the old Mac Pro in Firewire mode (hold down the T key on its keyboard as you boot) to show its drives on the new MP. This is basically as fast as putting the drives into a Firewire enclosure.
    Or you could boot it normally and share its files over the network using the Sharing panel of System Preferences. If you turn on both File and Screen Sharing, you don't even need to have a monitor attached - you can do all administration using screen sharing. However, this method requires that you open all files over the network, which will be slower than the direct-connect method above, and may also not work with all applications.
    Matt

  • 5770 with 27" Apple LED and two 20" Apple Cinema Displays w/Mac Pro

    As stated, I just bought a brand new Mac Pro 8-core (2010 ID 5,1) with a 5770 card and I'm trying to hook up a new 27" Apple LED and two 20" cinema displays. One of the 20" monitors is using the MDP adapter into the 5770 and the 27" is directly connected to the other MDP port. When I try to hook up the other 20" to the DVI port on the 5770 I get nothing. The screen is black and the it is not recognized as being connected. I'm using the standard DVI connector that came with the 20" direct into the 5770. To make sure it isn't a monitor problem, I switched out the 20" displays and both work using the MDP adapter but neither work plugging directly into the DVI port on the 5770. I believe the 20" monitors use DVI-D. (Is that correct?) So what's the scoop on getting blank screens when plugging into the DVI port on the 5770? Thanks for any help.

    "• the 27" is directly connected to the other MDP port.
    • One of the 20" monitors is using the MDP adapter into the 5770.
    • When I try to hook up the other 20" to the DVI port on the 5770 I get nothing.
    Note: If you are using an Apple Mini DisplayPort to DVI adapter, only two displays are supported across the three ports.
    If you are connecting three displays, any DVI displays must be connected to either the Dual-Link DVI port or must use an Apple Mini DisplayPort to Dual-Link Adapter.
    You MUST use All "Active" or "Powered" Mini DisplayPort connector such as the Apple Dual Link, or you can only use two displays

  • Premiere Pro CC continuous crash and extremely slow renders on a new Mac Pro.

    Hello,
    recently we changed our editing machines with the new Mac Pro with this configuration:
    - CPU 3,5 GHz 6 core Intel Xeon E5
    - 32 GB RAM
    - 2x AMD FirePro D700 6 GB
    we work on a server connected to the Mac Pro in Dual Ethernet configuration.
    The rendering of a sequence at 1920x1080 with 3 video tracks (video footage converted at ProRes 422 LT, a title on a linked After Effects Comp and a PSD graphic overlay of a small logo) of the length of about 3 minutes it takes about 4 hour... when it doesn't crash.
    When it crash, usually when i simply scroll the timeline, i receive an error message very long (if you want I can send you a rtf file about it, it's too long to paste it here).
    These are my system information:
    - Premiere Pro CC 8.2.0 (65)
    - I've installed every updates available at this time
    - OS X Yosemite 10.10.2
    Thank you very much in advance, and sorry for my bad english.

    Thanks Andrea for your assistance in reporting that additional information. You have come across an intermittent bug which has been reported by other users with no reliable repro steps for us to follow in house. So it appears to be mainly system specific, but we're not even sure which sorts of systems demonstrate it yet.
    One other thing to try is clearing your media cache files (from preferences > media panel). In the meantime,e the best thing to do is make sure you submit those crash logs to adobe whenever you get them. This helps us identify common thread among various users who may be experiencing the same problem. Also, if you have time, please file a bug report describing the steps that caused the issue in your case: http://adobe.ly/ReportBug
    Please be as specific as possible when describing your steps. Without a repeatable case, a bug like this is very, very difficult to fix. Thanks again for your support.
    To work around the sloe render for AE comp problem, please try right clicking on the comp in the timeline and then choose the "Render and Replace" command to transcode it out to a more easily handled format. This should help a lot with your performance slowness, and you will still have the ability to restore the original comp files if needed.

  • Want new Mac Pro With Snow Leopard

    I am after a new Mac Pro with Snow Leopard.
    I understand that some of the newer Mac Pros can have Snow Leopard installed.  Some tell me that in the recent past Apple made a change that made installation of Snow Leopard difficult or impossible on a Mac Pro.
    Does anyone know with a reasonable degree of certainty how to tell if a given Mac Pro can have Snow Leopard installed?
    I called Apple about a refurbished Mac Pro, they don't know what operating system it will come with!  And they don't know if it will include OS installation disks.

    For what it is worth, I recently went through this drama.
    Well, it's worth a lot!
    it is theoretically possible for Apple to modify the firmware to prevent Snow from booting, but my experience is that this has not happened yet.
    How long ago did you purchase your Mac Pro? (I miss the old days, when users would modify their own firmware.)
    See if you can buy from a seller who will let you test this out. There are some nice retailers out there, especially when you are dropping $1000s on a new Mac Pro.
    I've been looking for a while now, Mac Pro sellers that have Snow Leopard know how valuable there machines are. There are no bargains if you want snow leopard.
    We couldn't install Snow directly on the Mac Pro, so I installed on another computer (an older Mac Pro), and updated to 10.6.8 and swapped the drive across. This worked without issues.
    I currently own a 2008 Mac Pro (2,1) with 10.6.8
    See if you can buy from a seller who will let you test this out.
    Why not Apple?  They have a 15 Day return policy.   When I called Apple recently the person I spoke to suggested this.

  • The new Mac Pro (6,1) and TRIM

    With its economical internal design and limited internal expansion options, the new Mac Pro depends heavily on the speed and flexibility of Thunderbolt 2 for expansion. In the old days, we could add four HDs in the internal bays and one more under the optical drive. This also allowed us, if we used SSDs instead of HDs, to enable TRIM for other than Apple drives.
    We know that TRIM doesn't work with a USB 3.0 connection. The question is, can TRIM be enabled on an SSD connected in some fashion through Thunderbolt? I know that graphics cards can be plugged into an external PCIe expansion chassis and that eSATA SSDs, such as the OWC Mercury Accelsior_E2, can plug in too. But does having to pass through the Thunderbolt interface interfer with or prevent TRIM support? For that matter, what kind of external connection to an SSD at the other end of the Thunderbolt cable would be able to support TRIM? I'm currently using a CalDigit PCIe card which provides two eSATA external connections, and when a NewerTech Voyager Q is connected and an SSD plugged into it (like putting bread in a toaster), the drive is seen as "Rotational" in System Information, and TRIM cannot be enabled.
    Since TRIM support is important for continued performance and longer life of SSDs, is this an issue with the new Mac Pro's design philosophy?

    Hopeful but not comforting.
    With Mavericks, not all SSDs will report TRIM support, but doing a benchmark both before and after the change should confirm that TRIM is functional.
    I should see TRIM = YES and not from some benchmark.
    Thunderbolt support for TRIM is good. But Intel has as yet? never supported TRIM on an array, so not sure how that is accomplished.
    "Is" or "may" and "could" - I just  wouldn't make a "TRIM is supported by 10.8.5 and later" as it may vary by Macs that had native SATA III with PCIe support, the new Samsung controller Apple has been using. Certainly not in 5,1 Mac Pro except if and only for an Apple SSD BTO upgrade.

  • I purchased a blu-ray of The Hunger Games and it came with a code for a digital copy. I redeemed the code on iTunes but the download has been continuing for 2 weeks now and it never finishes! The time just keeps going up. Never an issue in the past.

    I purchased the blu-ray of The Hunger Games and it came with a code to redeem for a digital copy. I redeemed the code in iTunes and the movie downloaded fine, but the "EXTRAS" have been downloading for 2 weeks! Everytime I launch iTunes it starts the download again and the counter keeps going UP, at one point it said it would take 3 weeks. I have paused and restarted the download, I have deleted the download, nothing works to finish or stop this download! Does anyone have a clue what's up?

    ps when syncing it jumps through steps 1 - 4 real fast, i seem to remeber iphone showing the number of tracks transferring and names, but i see nothing? then it sits on 5 saying "waiting for changes to be applied"

  • I just purchased the hunger games on blu-ray with digital copy. when I try to download the HD digital copy it gets to about 80% compete then stops with a download error (-50). What is that how do I fix?

    I just purchased the hunger games on blu-ray with digital copy. when I try to download the HD digital copy it gets to about 80% compete then stops with a download error (-50). What is that how do I fix?

    Perhaps try the "Error -50," "-5000," "8003," "8008," or "-42023" section in the Specific Conditions and Alert Messages: (Mac OS X / Windows) section of the following document:
    iTunes: Advanced iTunes Store troubleshooting

  • Cs 6 blu-ray with sub menus, only go back to main menu

    I have burned a blu-ray with a main menu then sub menus: audio setup, chapters, extras.
    (note: they are regular menus NOT pop-up menus and I would rather not do pop-up menus at this time)
    when I am playing any of the sub menu content (trailer or making of or picking a chapter button from the chapter menu etc...) and press the menu button on the Blu-Ray player while it plays that content, it goes to the main menu instead of the sub menu.
    I checked it in the simulator and it was working perfectly....just as I would expect it to.
    each sub menu item (a trailer or making of featurette for example) is set to go back to the sub menu and it's button
    when done playing...and it does. 
    It just refuses to do that when the menu button on a blu-ray player is used and instead goes to the main menu.
    I ran the link checker before building the folders and burning it...no conflicts found.
    This seems to be an issue with Encore in general, reading about this here and in
    other forums.
    Can Encore simply not create a proper blu-ray disc with sub-menu's you can
    return to when the menu button on a remote is pressed?
    Do I have to buy BluStreak in order to correct these rather obvious navigation errors?

    Let us know what you find.
    I think the original poster in the other thread observed that commercial BDs were showing the same behavior.
    Even if true, it does not mean that some kind of scripting might not work.
    But Encore would not have the option.

  • Best export format for encoding & burning Blu-ray with toast?

    Hi!
    Have a 1 hour and fifteen minutes program which I burn to Blu-Ray with Toast 10/HD. The problem is the time it takes, about 25 hours. Is this resonable really?
    Maybe it´s depending on the format I put out from Final Cut - H.264, 1920 x 1080 (1888 x 1062)Stereo (L R), 48,000 kHz
    Does anyone know if there is a better export setting in Final Cut to get the process work faster in Toast?
    Best / Urban

    I've never used toast to burn a BluRay however I have used encore and I export 10 bit uncompressed out of FCP and compress that. If your over an hour of program you'll have to scale back the data rate to make it fit, a 90 minute feature looks good content wise, but any text on it will show signs of the reduced data rate. the encode typically takes about 8 hours to build the disk image on an 8 core mac then about 45 minutes to burn from the image. I burn first to a rewritable in case of issues, then if it passes muster I'll burn the master

  • FCS3- working blue-ray with surround sound ?

    Hi, I'm trying to solve the problem with surround and Blue-ray.
    *Could anyone confirm that FCS3 can output working Blue-Ray with 5.1 Surround Sound, please?*
    The surround sound is really important for me, I am able to make Blue-ray now via Toast, but it converts the surround to stero). As soon someone confirms it works, I'm going to upgrade... Thanks!

    The only things I noted when I made my first own test, was that even though my FCP7 timeline was set properly to output the 6 channels, when I went to compressor 3.5 to produce both the H264 and the AC3 (with 6 channels), after the Blu ray disk was burnt, the audio was not playing correctly.
    I fixed the problem by going from FCP7 to Compressor using the new function called "send to compressor", instead of using a self contained QT movie (which is my usual workflow).
    In this specific case I found that it solved my problem and my second attempt to produce the Blu ray disk was ok, the audio played as expected on my Dolby receiver.
    Regards,
    Armando.

  • My husband and I share a new PC.  We have different music tastes and each have an iphone.  How can we both use our one computer and one itunes program with separate music libraries and separate iphones?

    My husband and I share a new PC.  We have different music tastes and each have an iphone.  How can we both use our one computer and one itunes program with separate music libraries and separate iphones?

    Each device only syncs waht you select.
    Select only what you want for each phone.

  • Develop mode shows a blue background with a white box and white diagonals.

    When I open the Develop mode the photo I selected is not displayed. Instead is a blue background with a white box and white diagonals. Can anyone help? Everything else appears to work. If  I choose the Before and After view the photo shows in the  Before but the blue screen in  the after.

    You should find the forum for whichever product this concerns and post your question(s) there.
    Here is a link to a page that has links to all Adobe forums...
    Forum links page: https://forums.adobe.com/welcome

  • What does it mean when you computer crashes and when you turn it back on it shows you a blank blue screen with a little folder and a question mark in the middle?

    What does it mean when you computer crashes and when you turn it back on it shows you a blank blue screen with a little folder and a question mark in the middle? It's a old imac from 1997.

    I don't have original discs that it came with.
    Then you still can use the second option with the keyboard combo I posted, called "resetting the PRAM."
    Also when you way hold the c key down do you mean turn computer off and turn back on holding the c key?
    Yes, or you can simply restart. As you don't have the CDs, this isn't on the plate any more.
    The internal backup battery is not expensive and, in most iMacs is user-replacable. If yours has a tray-loading optical drive like this one:
    it takes a major teardown to replace the internal battery. If this is the case, you'd be better off to leave the computer plugged in all the time; that eliminates the main reason for having a working battery.
    If it has a slot-loading optical drive like this one:
    things are much easier. The battery is visible through the RAM access door on the bottom of the computer case. The manual:
    http://manuals.info.apple.com/en_US/iMacG3_2000UserManual.PDF
    has sketches of how to access the RAM and therefore the backup battery. Unfortunately, the pdf on the manual goes up sideways on-screen and the RAM instructions are pretty deep into the manual. It's probably easier to scroll (for a while) to the section on adding RAM and print the applicable pages.
    When you work on the battery, some sort of non-conductive pliers or large tweezer or forceps help unless you have tiny fingers. Make sure to note the polarity of the old battery and install the new one in the same orientation.
    The battery itself is readily available. If price is no oblect, you can get it for a small rasom from Radio Shack Store ("Tandy" outside the US) as part number 23-026.
    Online, they are dirt-cheap even after adding shipping. I buy backup batteries form this outfit:
    3.6v Newer Technology Lithium 1/2 AA PRAM Computer Clock Battery

Maybe you are looking for