Blue screen error when connecting an ethernet cable

I have a Compaq Presario 5300US desktop that I'm trying to upgrade. It has 512mb (max) of memory and a newer video card than the factory one. I installed Vista Home Basic on it with no problems. I also installed a pci ethernet card along with the Vista drivers that came with it. I checked tha card's properties in "device manager" and it said "This device is working properly". I haven't plugged in an ethernet cable to the card at this point. Everything is working OK, but as soon as I try to connect the card to my router, I get a blue screen with this message:
Hardware Malfunction
NMI: Parity Check / Memory Parity Error
*** The system has halted***
I don't get any memory errors as long as I don't try to use the ethernet card.

Hello @larrycarol99,
I understand that after upgrading your computer when you plug in an ethernet cord you get a hardware malfunction error. I am providing you with a Microsoft Support document: Hardware Malfunction Results in System Error Message that explains what causes that error and provides steps on fixing it. I am also including a link to the Compaq Presario 5300US Desktop PC Drivers page, which unfortunately does not have any drivers for your computer running Windows Vista.
I hope this helps. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Similar Messages

A205-S5866, "DRIVER_IRQL_NOT_LESS_OR_EQUAL/Blue Screen event", when connected to Ethernet,

I will apologize in advance if I'm in the wrong place or if this is too elemental, I tried searching a bit before posting. But here goes...
I started getting the "DRIVER.IRQL_NOT_LESS_OR_EQUAL" message/Blue Screen problem event yesterday. There are a few things that over the course of the last 24 hrs that started to appear as potential triggers/accomplices. (maybe I was/am reaching, I don't know)
*It only has happened when my laptop was connected to an Ethernet wire/chord. This was the 1st time I had used it, previously I had
always used wifi. (without any problems)
*It seemed to crash/shut down around when I would sign in or out of yahoo messenger or my "myyahoo" page
Extra points of relevant info... 2 things that I did hours before the 1st occurrence:
1) I did a windows update (the automatic kind, that you get notices prompting you about);
2) I had internet service set up in my apartment & the company's tech did the installation. (also, I am from the U.S. and bought my laptop at home before I left, but I am now in Seoul, S. Korea, just in case that is relevant somehow)
What I have done (after this started to happen) so far, is 1) used the internet via wifi without problem, 2) performed a system restore to before the automatic update, 3) tried again with the Ethernet & encountered the same problem.
Thanks in advance for any advice/suggestions!
Solved!
Go to Solution.

Jerry & CristopherC, again, thanks for your replies. Not sure if you realize how much the "technologically challenged" like myself appreciate the help!
OK...
ChristopherC you understood correctly, I have been able to access the net (& stay on for long periods of time) without any problems. But when connected by the ethernet/modem I get those messages, etc.
*I am trying as hard as I can to avoid the "clean wipe" of my cpu because as I mentioned, I am in Korea & I have a "slingbox" type thing that I am accessing back home to get American cable, and if I perform that, then the network connection I established will be lost.
Jerry - You nailed the "stop #/BCCcode" it was D1. The time I had the Microsoft "auto search" for a solution, it came back with this info.: BCCode d1, BCP1 00000004, BCP2 00000002, BCP3 00000001, BCP4 8BDD5DD9, OS Version 6_0_6001, Service Pack 1_0, Product 768_1
BUT... I copied down the just the message info. (without the autosearch) 2 of the other times, and it gave:
-Stop: 0x0000008E (0xC0000005, 0x82BF3DD9, 0xA6DE3204, 0x00000000)
-Stop: 0x000000D1 (0xCBE46973, 0x00000002, 0x00000000, 0x8289DB4E)
Also, I made an attempt once at the "Safe Mode Diagnostic", and got this other info... Prob Event Name: Blue Screen, Locale ID: 1033, OS Version (which seems slightly different than the #'s above) 6.0.6001.2.1.0.768.3
I not sure what, if any, significance this info has. :-)
OK, I will to do those hot fixes you suggested & report back. Thanks again!

Blue screen error when I plug my iphone into my PC

HELP!!! I just got an iPhone, and now when I try to plug it into my PC, my PC crashes and gives me a blue screen error. I have made sure I have the latest updates of itunes, and Windows, and I am just not sure what to do . . . Can somebody please walk me through this? Everything I read talks about syncing, but that requires that the computer doesn't crash the minute I put the iPhone into the USB jack . . .
I did sync it once fine, downloaded a few apps, which was also fine. Now I took some photos with my iphone, and wanted to put them on my computer, but it won't even let me plug it in. Please HELP!!!
Thank you.

My System also crahses from time to time, on connecting the iPhone. I have also checked this thread (http://discussions.apple.com/thread.jspa?threadID=1174035) but I dont have a logitech CAMERA. I do have a G15 Keyboard and a mouse but nothing else. THe Problem with the crash is: My pc neither shows a bluescreen nor is rebooting. Means: direct power off, like I would have pulled out the cable...
very weird....plase help me, if you have any Idea.

Blue Screen Error when syncing ipod touch 4g 32gb with i tunes 10 on Vista

Hi
I'm trying to sync my ipod touch 4g with my itunes 10 using a Dell XPS with Windows Vista. After the point where the songs begin to copy (around 5 mins to 30 mins into copying) a blue screen error is caused and the computer shuts down automatically. The blue screen error ID is 2057.
I have scanned for viruses and its clean, tested my hardrive and its all ok, and now been to apple and got a replacement ipod and usb, re-installed i tunes 10 BUT its still happening.
i'm not sure what to do next ..any suggestions??
BTW my computer works fine until I try syncing the ipod so it's definitely something related to it.

Just in case anybody is interested I managed to resolve the problem. Not sure if it was a just a co-incidence but after windows had auto-removed itunes 10, I plugged in the ipod and the computer recognised it as a working piece of hardware, although it actually thought it was a camera (not sure if that's normal).
Anyway I re-installed itunes10 but kept the ipod plugged into the usb all the time. When itunes had installed, i began the sync and the files copied far more quickly than in previous attempts. They are all on now and the ipod is working fine and no blue screen errors.
What probably happened is that when windows auto-fixed errors after the last crash(it didn't run an auto-fix after previous crashes), it fixed the error which was crashing itunes10 when syncing. I hope nobody else has this problem and the ipod remains ok.

Satellite A200 - Blue Screen error when trying to open HWSetup

Hi,
I get a Windows Blue Screen error whenever I try to open HWSetup or access the Toshiba Flash Card using the Fn key.
Any ideas how to solve this?
Cheers!

Hello
The error message invalid serial number occurs if you try to install a software that is not designed for this notebook. Maybe you did download the HWsetup for an other notebook.
Check this!
Furthermore I have searched in the forum and maybe this could be useful for you:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=150557&#150557
Greets

Why won't my old iMac G4 recognize my Airport Express when connected with ethernet cable?

After I installed an Airport Extreme as a base station for my network, the G4 couldn't recognize either the Airport Express or the Airport Extreme unless it was connected by ethernet cable to the Airport Extreme - then both devices show up in the G4 utility. I have reset the Airport Express to factory settings many times and the Utility in my iMac 3.2 Ghz Intel Core 13 indicates that the Airport Express is working. Any ideas?

I suspect its to do with the WPA setup support changes. My very old G3 seemed to have the same issue of not able to connect to Extreme or Express. Used to connect before years back to Apple routers but refused to in recent time for reasons not explainable so I just connect it now via cable.

Blue screen crash when connecting iPod

Whenever i plug my ipod into my computer, windows goes to a blue screen with the following message...
A problem has been detected and Windows has been shut down to prevent damage to your Computer.
If this is the first time you have seen this stop error screen restart your computer. If this screen appears again follow these steps.
Check to be sure you have adequate Disk space. If the Driver is identified in the stop message disable the driver or check with the manufacturer of the driver updates. Try changing video adapters.
Check with your hardware vendor for any BIOS updates.
Disable BIOS memory options such as Caching or Shadowing. If you need to use Safe Mode to remove or disable components Press F8 to select advanced start up options then select safe Mode.
Technical Information
*stop:0X0000007E (0XC0000005,0X00000000,0XF7A9B7C8,0XF7A9B4C4)
Beginning dump physical Memory
Physical Memory Dump Complete
Contact your system administrator or technical support Group "
This all started happening when i was away in America and my dad plugged his iphone into my pc to try and get some of my music, which caused the same crash. My ipod plugs in fine to his computer though. Any advice much appreciated

Apple Genius, behave yourself.
Here's the article how to fix this problem: http://support.apple.com/kb/TS1502

Can access internet when connected w/ethernet cables in router, but WRT54G says it can't connect

I have my router, modem, and computer all set up correctly. I can access the internet in this setup but with only the computer that is connected with the ethernet cord to the router. Yet, my WRT54G router can't connect to the internet in the Linksys easy setup nor through the http:192.168.1.1 method.
When I changed the internet connection type to PPPoE, my modem was unable to access the internet. I also changed the IP to 192.168.2.1 but that didn't help. I have performed several power cycles. I have upgraded the firmware.
I changed the internet connection type back to DHCP, so I am able to come on this website, but I can't set up the wireless since the router says it can't connect to the internet. Please help!

Start it from scratch...Reset your router and re-configure it...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page.
If your Internet Service Providor is Cable follow this
If your Internet Service Providor is DSL follow this
To change the Wireless Settings click here and Enable Wireless Security
Now see if you can locate your wireless network on your wireless computer and attempt to connect...

770T-C45 Maiboard - blue screen error when installing 4GB RAM

Greetings,
I bought the MSI 770T-C45 mainboard to replace my older mainboard (ASUS M2N32 SLI Vista Premium). The problem is that the MSI board resulting blue screen when i install 4GB of RAM. First i thought maybe because of the BIOS. The same problem occur after i flashed the BIOS with the latest version using MSI Live Update. Here are my current PC information:
AMD Athlon II X2 X245 - 2900MHz (overclock to 3487MHz)
MSI 770T-C45
1Gb OCZ Gold PC6400 (3 sticks)
PowerColor ATI HD4870 1Gb Stalker Edition
Hitachi SATA2 250Gb
Vista x86 SP2
CoolerMaster extreme power 550Watts
I wanted to use Vista x64, but since my board can only support 3GB of RAM, so i use vista x86 instead.
Could anyone give me some suggestions? It is a waste to not fully use all the DIMM slots.

Quote from: Svet on 21-March-10, 10:15:34
remove the OC
unfortunately the problem occur before the OC.. i just did the OC yesterday..

Blue screen error while instaling.

Hy
I get the blue screen error when i install the flash player.
Windows 7 32 bit
Firefox 16.0.1 32 bit
I had the older flash version but i removed it tryng to solve the problem but no succses.
This is the version i try to install
11.4.402.287
i dont remember the older one.but it was making updates every time a newer version was coming.
This is the error
Problem signature:
Problem Event Name:    BlueScreen
OS Version:    6.1.7601.2.1.0.256.1
Locale ID:    1033
Additional information about the problem:
BCCode:    d1
BCP1:    01000018
BCP2:    00000002
BCP3:    00000000
BCP4:    82221031
OS Version:    6_1_7601
Service Pack:    1_0
Product:    256_1
Files that help describe the problem:
C:\Windows\Minidump\101312-16005-01.dmp
C:\Users\Silviu\AppData\Local\Temp\WER-25896-0.sysdata.xml
Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409
If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt

Hello pleurisy,
Your system is getting an error when trying to play a game.
This might be caused by the system getting too hot.
Do a hard reset.
Turn the computer off.
Remove the power cable and the battery.
Hold down the power button for 15 sec while booth power sources are removed.
This should reset the hardware in the computer.
As you turn it back on tap the F10 key. This will load BIOS setup utility.
Press F9 to load defaults.
Press F10 to save and exit.
When the computer boots back up, check to see if everything is working.
If your still getting the error, go to HP.com and update the BIOS.
Here is a link to the update.
Also make sure that the system does not have a buildup of dust inside the system.
Take the side panel off and clean the inside of the computer with compressed air.
Let me know how everything goes.
Have a good day.

Can you connect an ethernet cable to an Airport Express Extension?

I have an Airport Express that I am using as an extension to my current home wireless network.
That is successful and I have a green light. I am trying to plug in an ethernet cable to allow an older mac without an airport card to connect to that Airport Express Extension. When I turn off the airport and select Ethernet Cable, I am told that the cable is not connected to the internet. The wireless works fine and I can get full bars in the far part of my house - but I do not get internet when connecting an Ethernet cable.
Help!
Thanks in advance

See my reply to your other post.

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC has been turned on (PC is connected via Ethernet cable, and has no wireless capability as far as I know). What gives? It works fine when the PC is off.

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC is on (the PC is connected via Ethernet cable, and has no wireless capabilities that I know of). What gives? When the PC is turned off, everything is totally fine. I\m stumped.

Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
I suspect a problem with your router. Try changing the security. First use no security as a test.
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Windows Blue Screen Error Message Appears As Soon As IPod Connected

Everytime I connect my IPod to my computer, I get the Windows Blue Screen error message. Thought it was the cable, so plugged cable in by itself. No problem. Uninstalled IPod and ITunes software and then plugged in IPod, still got the Blue Screen. The Blue Screen says something about "recent plugged in device problem". It is not the cable, it must be the IPod. Did not have this problem when I bought it. Tried it on labtop and get the same error message. I can't do updater or anything that requires me to plug the IPod into a computer because the Blue Screen appears immediately. When I unplug, the Blue Screen remains and locks up the computer so I have to restart each time. I have tried everything I can think of. Please help.

Hi Mike thank you for replying,
I am not able to start the computer in safe mode, safe mode with networking, last good known configuration etc, Each time it quickly blue screens and restarts about two secs into the process.
I was unable to try a clean OS install from the disk as it gave the blue screen error shown in the original post. The same thing happened when I tried to use the repair option on the XP home disc. So i can't get into the computer at all to start diagnosing the fault, the only clue I have is the error message, and after searching the internet I haven't found much enlightenment from that yet.
If you can help me out or suggest where to search it would be much appreciated.
Thx

I am trying to connect my iPad to my windows pc ( xp) but it does not recognise the iPad and I get a blue screen error causing the pc to shut down. Any ideas

I am still not able to connect my iPad 2 to my Pc ( windows xp). When I try to do so I get a blue screen error and the computer shuts down. I have reinstalled iTunes. iPod works fine. Any ideas?

Not sure, but try these.
Disable your firewall and anitvirus software temporarily.
Restart the iPad by holding down on the Sleep button until the red slider appears and then slide to shut Off. To power up hold the Sleep button until the Apple logo appears and let go of the button.
Reset the iPad by holding down on the Sleep and Home buttons at the same time (for about 10-15 seconds) until the Apple logo appears (ignore the red slider), then let go of the buttons.
 Cheers, Tom

Blue screen error after USB connection

hello, I have a new 8100. All is great, all is working, but the problem appeared after I installed the software and I connected the mobile to the computer by USB... the blue screen error of Windows Vista appeared and then
after the automatic reboot of my computer
it said the following mistakes:
"Firma con problemas:
Nombre del evento de problema: BlueScreen                        ( name of the problem )
Versión del sistema operativo: 6.0.6000.2.0.0.768.3             ( OS version )
Id. de configuración regional: 3082                                    ( regional configuration ID )
Información adicional del problema:                                    ( aditional info on the problem )
BCCode: 4e
BCP1: 0000009A
BCP2: 0003EA16
BCP3: 00000006
BCP4: 00000002
OS Version: 6_0_6000
Service Pack: 0_0
Product: 768_1
Archivos que ayudan a describir el problema:       ( files which help to describe the problem )
C:\Windows\Minidump\Mini010609-03.dmp
C:\Users\antonio\AppData\Local\Temp\WER-110323-0.sysdata.xml
C:\Users\antonio\AppData\Local\Temp\WER6C68.tmp.version.txt
Lea nuestra declaración de privacidad:
http://go.microsoft.com/fwlink/?linkid=50163&clcid=0x0c0a
I hadn't anything wrong with my Vista OS before
thanks in advance
Solved!
Go to Solution.

Hi and welcome to the forums!
I don't read Spanish very well, but did you leave the Blackberry plugged in when you
rebooted the PC? Vista might have tried to used the BB as a drive for error checking or system functions.
Thanks,
Bifocals
Click Accept as Solution for posts that have solved your issue(s)!
Be sure to click Like! for those who have helped you.
Install BlackBerry Protect it's a free application designed to help find your lost BlackBerry smartphone, and keep the information on it secure.

Blue screen error when connecting an ethernet cable

Similar Messages

Maybe you are looking for