Blue Screen of Dead when installing Nvidia

Hello everyone, I Have a HP ENVY 15t-j000 and newly formatted because was too slow. When I started to install all the drivers from HP website, everything was running fine and the only driver left to install was the Nvidia GT 740m. I downloaded and installed the Nvidia driver from HP web site, the installation run without problems, I was asked to restarted the computer, but when the computer started, I've logged in and after 1 or 2 minuts I receive a BSOD power state failure (error 0x9F from minidump). I've done a restore to the previous installation, and tryied to install the driver from Nvidia web site, no sucess again (BSOD dpc watch dog violation) Does anyone know how to proceed ? ps: I don't have the recovery partition anymore.

Hi ,
Thank you for visiting the HP Support Forums and Welcome. It is a great site for information and questions. I have looked into your issue about your HP ENVY 15t-j000 Notebook and issues with Nvidia. I would not install this driver package. I would run the HP Support Assistant. It will install any software and drivers that are needed for your system.
Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system at the time of purchase or that need updating. Thanks.

Similar Messages

K9N2 SLI Platinum Blue Screen of Death when installing Windows XP

My hardware includes:
•   MSI K9N2 SLI Platinum Motherboard
•   Corsair XMS2 TWIN2X4096-6400C5
•   GeForce 9800 GT 512MB GDDR3
•   AMD Phenom X4 9850 Quad Core Processor, Black Edition 2.5GHz
4MB Cache 2000MHz [4000 MT/s] FSB
•   Thermaltake Ruby Orb Aluminum Core CPU Cooler
•   UltraX3 850 Watt ATX Modular Power Supply
•   [1] Western Digital 200MB7200 ATA133 [Not connected yet]
•   [1] Maxtor 80MB ATA133 Drive [Not connected yet]
•   [1] Western Digital 500GB 7200RPM 16MB SATA II HARD DRIVE
•   [2] Seagate 7200.11 ST3500320AS 500GB SATA Hard Drives With 32 MB Cache
[Not connected yet]
•   LG DVD-RW
•   Toshiba DVD-ROM [Not connected yet]
•   AMI Bios v02.61
•   Antec Full Tower case
After partitioning my drive with Fdisk I tried to install Win Xp. My plan was to format the drive with XP. XP starts up and runs through the initial system check then when it prepares to install I get the blue screen that says [my words] "Windows has shut down to prevent damage to your system. If drivers are mentioned try disabling them in the BIOS or get the latest bios update from the equipment manufacturer..." The error is:
Stop 0x0000007E on the next line
pci.sys - address f7480BFbase at f7487000 Datestamp 3b7d855c
Just never had these problems setting up a system and soon I will be able to say it took me 2 years to get this running. Hope someone can help. Thanks

Use XP Installation disk with SP2 or SP3 included to fix the BSOD.
Simple your XP installation disk is outdated and cause troubles with latest hardware.

Blue screen of death when installing Adobe Air

I'm trying to install Adobe Flash CS6 and Adobe Air along with it. About 10 seconds after pressing "install", my computer shows the blue screen of death for a split second, and then restarts.
To my knowledge, I do not have Folder Lock. I also cannot find any windrvNT.sys in the C:\WINDOWS\system32 folder, even after turning on the "show hidden files and folders" option.
Using Windows XP

Raymon_Zheng111 does your computer meet or exceed the system requirements for Flash CS6 listed at http://helpx.adobe.com/x-productkb/policy-pricing/system-requirements-flash-professional.h tml#Flash%20Professional%20CS6%20system%20requirements.

Blue Screen of Death when installing latest patches for Windows 7

I get a BSOD when I installed the latest windows patches. the actual error message skips between a General protection Fault and the following:
DRIVER_UNLOADED_WITHOUT_CANCELLING_PENDING_OPERATIONS.
It is involving the file applemtp.sys at stop 0X000000CE
I am unable to recover from it including a "safe mode" and a revert to previously known configuration.
Any ideas would be greatly appreciated.

Solution for this problem is simple. You have to apply Mac Book Air SMC Update 1.7 which you can do from Mac OS X with Software Update or you can download required update manually from Apple support site. If you don't use BootCamp and have installed Windows without it, you will have to boot Mac OS X from external drive just to apply required update. After you applied SMC update, you can boot to Windows and apply BootCamp update 3.2 and 3.3.
There is a known problem with Mac Book Air EFI Update 2.3, which you won't be able to apply and it will show in Software Update every time you check for updates. There is no solution for it yet.
You get BSOD if you have BootCamp 3.1 and Windows 7 SP1 installed and you have commited Windows update which will break applemtp.sys as your SMC firmware is too old. It applies to Windows 7 32 bit and 64 bit versions in BootCamp or native install.

Blue Screen of Death when connecting ipod

Ever since the 2.0 update, when I try and connect my ipod about 50% of the time i get the BSOD. What the heck is going on? Is it another 2.0 bug?

The following document is worth checking through:
What to do when Windows XP or Vista computer displays a blue screen error message when syncing the iPhone or iPod touch

Blue Screen of Death When Plugging in Ipod Touch 4g

Hello,
Im reciving blue screen of death when I plug in my ipod touch 4g. I have updated itunes, Drivers, This happens every time and I suspect it happens when my computer says found new hardware reconizing the ipod as a camera because once I pluged my ipod in and it didn't pop up found camera hardware and it worked. So does anyone know how to fix this or disable my comp from reconizing the ipod as a camera? Thanks in advance
p.s im using XP service pack 3

have u tried pluging an other usb (eg mp3 or mem stick) it to ur compuer? is it doing it with these?
if its only doing this with ur ipod try the following
1 go to start menu and in the search box type in usb
look for device manager
2. open the disk drives and plug in ipod touch and removeable disk should show up
3, try usb drives updates
because the ipod has a camera most older computers running xp think its a camera,
if u have and usb mem stick copy ur itunes folder on to it and copy it to a computer running vista or windows 7 and c it its doing it on one of them, if its doing it on one them there may be other hardware isues with ur ipod touch

Blue screen of death when syncing verizon I phone

I receive a blue screen of death when I try to sync my I phone 4 with I tunes on my laptop. The initial sync went fine, I am connected to my Exchange server for email and have downloaded CD's to I Tunes, when I try to sync...blue screen. I have run registry fix and virus programs and have no errors. Does anyone know how to fix this?

The first response was correct, the computer (xps 1210) used a logitech camera driver that I did not recognize so I deleted it. The software was still active and crashed the computer. Fix was reinstall logitech software and driver. Updating the driver would have probably worked. Thank you!

Blue screen of death when La Cie external firewire drive connected

I tested a LaCie external firewire drive on my iMac and it worked fine. I packed it up well and posted it to a friend who gets the blue screen of death when the LaCie is connected to her iMac. She's not even trying to boot from it.
My iMac is 9.1 and hers is 8.1. We are both running Snow Leopard. Was there some problem once upon a time with chipsets or am I mis-remembering?
TIA

Create an ISO (Encore) or folder on your hard drive (Encore or Premiere Elements) and then use the FREE http://www.imgburn.com/index.php?act=download to write files or folders or ISO to disc for DVD or BluRay (send the author a PayPal donation if you like his program)
Imgburn will read the ACTUAL disc brand from the disc, which is not always the same as the box label (Memorex is notorious for buying "anything" and putting it inside a Memorex box)
When you write to disc with Imgburn, use the SLOWEST possible speed setting, so your burner has the best chance to create "good, well formed" laser burn holes... since no player is required to read a burned disc, having a "good" one from a high quality blank will help

"dependency cycle detected" warnings when installing nvidia driver

I'm getting two "dependency cycle detected" warnings when installing nvidia driver on a fresh arch system:
xorg-server will be installed before its nvidia-libgl dependency
harfbuzz will be installed before its freetype2 dependency
Is that normal?

It's not 'normal' but if everything is working fine, no need to worry. They're just warnings, not errors.

Macmini 2011 on lion, goes to a blue screen om monitor when awakening from sleep mode, last 3 or 4 seconds, can anyone help? Thanks

Macmini 2011 on lion, goes to a blue screen on monitor when awakening from sleep mode, last 3 or 4 seconds, before desktop appears, can anyone help? Thanks

Depending on the system configuration, this may not
be unusual. The Mini that I use for my home theater,
which is connected to a receiver then to a TV, all via
HDMI usually takes a couple seconds to come up just
the way yours does. Same happens when I switch sources
on the receiver. Actually, it starts with the blue screen and
will sometimes flash before the desktop comes up.
It seems that when HDMI goes dormant, there is handshaking
that needs to be re-established, at least thats my SWAG on it.
On the other hand, the Mac Mini Server that I use as a work
station and is connected to a Thunderbolt Display, wakes to desktop
in a second, maybe two. On this combo, it just comes up to
the desk top.
It also probably depends on what processes were active when
the Mini was put to sleep. So it may take some time for it to get around
to reloading the desktop.

Blue Screen of Death when I try to install Leopard drivers.

So, I've been able to use Boot Camp to install Windows XP, SP 2 on my new 20-inch aluminum iMac. This is the same version (same disk, in fact) of Windows that I installed on my old 17-inch iMac, and it worked perfectly then.
After I finish the Windows installation, and put the Leopard disk in to install the drivers, nothing happens. No Autoplay. When I go into My Computer, and double-click on the cd, the installation process starts. After cycling through 4 drivers, I get the blue screen of death and the computer reboots.
When everything restarts, Windows tells me that I suffered an error. I can't send an error report off, because Windows won't acknowledge my wireless internet connection yet, without the Apple drivers.
I've tried to transfer the Boot Camp 2.1 update to the Windows partition via 2g flash drive, and no luck. Trying to run the update doesn't do anything, the icon simply lights up for a moment and then un-highlights. Nothing happens.
I'm really confused, I didn't have ANY problems like this on my last iMac. Any help anyone might have would be greatly appreciated.

There IS another way to try this.
Boot to Windows and right-click My Computer or My Documents and open as "explore". Insert the Leopard disk. If it offers to install STOP it. Click on the LEFT side the plus sign next to the machine's DVD drive icon (the reason we opened the "explore" style directory). The Boot Camp files are now passive but exposed. Next right click My Computer and click properties. Next hardware and then device manager. Now you can one-by-one install the drivers using Windows hardware wizard. You might even want to drag the contents of the Leopard disk (drivers) right on to your (Windows) "desktop". In device manager open Human Interface Devices - you will find Apple Keyboard or whatever an iMac has there. Rightclick and hit Update Driver - the Wizard opens. Click 'no - not this time' and continue. Click 'install from a specific location' and continue. Next the Wizard gives you a 'browse location' option. Just click around until you locate the Boot Camp drivers in your disk or desktop and proceed - it will update, I promise you.

My PC is Pavilion dv7. When I insert Blue Ray Disc, Blue Screen occures. I install PowereDVD 11.

No error occurs when using DVD and CD-ROM. I could use Blue Ray Disc (any format of Blue Ray Disc including commercial movie disc) three months before (May). I also asking cyberlink in case software problem. Should I attach system error log ?

Thank you for your info. I tryed to update driver to the latest one on device manager, but it says "this is the latest
version". So I delete the DVD/CD-ROM entry from Device Manager, and execute H/W cahnge auto-scan.
Then driver is automatically installed, but the version is still the same (v1.00).
Mnufacturer: standard CD-ROM drive, dated 2006/9/1，version 1.00
Provider: Microsoft
Friendly Name: hp BD MLT UJ240
It seems I can't find correct driver. I can't find URL of manufacturer.
I also installed "sp50287" OS enhancement patch for HP pavilion dv7, which was suggested by HP support
engineer in Japan, but still blue screen occurs, after answering "Yes" at "Do you confirm the update info" menu
at HP Media Smart. I wonder it seems CODEC problem.????

HT3986 blue screen of death when windows 7 is trying to complete install on iMac late 2006 running on Lion 10.7.5 with bootcamp 4.0.4...can someone pls help and thanks

trying to install windows 7 32bit ultimate on my late 2006 iMac with bootcamp 4.0.4 running on Lion 10.7.5, but it can't complete install, the BSoD appears as soon as it tries to reboot to continue setup, last stage reached " setup preparing computer for first time use and registry change" never seen reaching setup checking video performance then BSoD kicks in followod by black screen sayinng windows did not shut down properly, tried in safe mode, with advance mode, rebooted in install disk and ran repair, says cant fix it automatically, with messge 07: Failure during setup o.s. version 6.1.7600.2.0.0.256.1, tried to install nvidia geforce 7600 but mac says cant or not needed, been trying everything i can for 2 days no sleep...im slowly losing it
...any help will be appreciated and thanks

One person had iffy 3rd RAM.
You updated AMD graphic driver too to 11.8+ right? not just Apple's.
Plenty of free space for Windows to play with.
Do a chkdsk
Boot from Windows DVD and run memtest and also do system check
Restore points are better used, and image Windows
Rollback drivers works well, too
Some had trouble after NetFrame 4? update in Windows (but not on my 3 computers)
Apple drivers can be iffy and buggy
AppleHFS.sys has been known to be trouble. HFS allows for filenames that NTFS won't.
Paragon has HFS9.x driver that adds write support and does a better job
BC 4.x is still it seems trouble for more than a few (but obviouslly not in the 10s of thousands)

Blue Screen of Death When opening iTunes.

I am at a loss. For the past six months I have been trying to figure out why my computer has a blue screen of death and then restarts "nearly" everytime i open iTunes. The "nearly" is what's driving me nuts because every once in a while it will open ONCE and then start crashing again. I don't even do anything to help it open it just miraculously works every now and then. It even craches the comp when starting iTunes in safe mode. The blue screen error says "Page Fault in non-paged area". iTunes worked fine for months before this randomly started happening. I have tried every solution I have seen, even ones that weren't for my problem. So far I have:
Manually uninstalled iTunes and QT and reinstalled the standalone QT then iTunes.
Disabled itunes helper and ipod service before starting.
Disabling all other services and start-up items.
Installed current bios and drivers (as far as I can tell)
Installed current windows installer.
Updated microsoft products including .net
Updated Java runtime environment
Replaced ram
I have a pentium 4 1.6ghz with soyo mobo and a RAID card(mirrior) set-up. 1 gig of pc133 ram. I can ul the minidump if needed.
I figured out how to load my podcasts on my ipod manually but I want to get a video ipod so I need itunes. PLEASE HELP!!
Windows XP

there's a few more things worth checking on. but let's also capture a minidump of the crash and send it to someone who can interpret minidumps.
To set up your machine to capture a minidump, right click on "My Computer", select "Properties", select the "Advanced" tab, select the "Startup and Recovery" Settings button, select "small memory dump" from the popup. When it crashes, look for the MiniDump file. It's usually in the folder "C:\WINDOWS\Minidump" and is called something like Mini<number>-<number>.dmp.
send it to this email address
in the email, put the URL to this discussion thread, so that whoever gets it has some context. Also give as much information about the context of the crash (in the email) as you can.
love, b

Blue screen of death when connecting ipod or running itunes

Please help me, I get the blue screen of death and its down to my itunes/ipod i think.
Uninstalled Itunes (tried doing this in safe mode but it wouldnt let me saying you cant do this) and re-installed it but when try to use it (ipod not connected) my screen either freezes a few moments later or the BSOD appears.
Ive ran a windows disk check and a system mechanic 7 one as well, a few folk on here have said my ipod might need reset but this is happening without the Ipod connected so is still an issue?
My ipod seems to be working fine, obviously i cant even access itunes to reset it or see its status.
Any help would be greatly appreciated.

Have you tried this?
http://support.apple.com/kb/TS2280
CG

Blue Screen of Dead when installing Nvidia

Similar Messages

Maybe you are looking for