Blue Screen on T60p after using ThinkVantage to update on 5/7/2008

Yesterday I used the Thinkvantage to update my T60p system and afterwards I had the Blue Screen of death. I could re-boot in safe mode and in MSCONFIG if I use selective startup, I can boot the system. If I go back to regular startup, it consistently gives the blue screen. How do I identify the problem and how do I deal with it?
Thanks!

Hello,
Have you tried re-enabling the modules in the System Configuration Utility (filename: MSCONFIG.EXE) and rebooting after each change to see if you can find the faulting application?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Similar Messages

Blue Screen error message after using Rescue and Recovery.

Good morning - I unfortunately had to use the IBM Rescue and Recovery feature to restore my factory settings. However, now my computer is giving me a blue screen error during the startup process. Unfortunately it is not on the screen long enough for me to get too much information from it, but I have been able to get win22n51.sys as being some sort of error message. If I start the computer in safe mode it will load without the error. If I use the safe mode plus networking it gives the error. So I'm assuming it has something to do with the network drivers?
I would appreciate any ideas you all have for resolving/further diagnosing this problem.
Thank you!

Hello,
Perhaps this Lenovo knowledgebase article, "XP Crash: System may hang or restart with a previous version of the Intel PRO 2200BG Mini PCI adapte..." will be of help to you in resolving the problem?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Blue Screen of Death after GPIB Software Drivers 2.1 install, nipsbfw.sys, nipalk.sys

I get a blue screen of death after I upgraded the GPIS Software Drivers to 2.1. The screen complains about the following files: nipsbfw.sys and nipalk.sys.
I'll copy down the exact message and post it...

Hello fkwok �
First, make sure GPIB software driver 2.1 is the correct driver for your operating system and board by clicking here.
If you are using Windows 2000, this KnowledgeBase is extremely useful.
If these suggestions do not solve your problem, please post the exact message and I will look into the issue some more. Have a great day!
Becky B.
Applications Engineer
National Instruments
Becky Linton
National Instruments
Field Engineer
Office: 734-464-2463
Cell: 248-709-2822
Email: [email protected]

Qosmio F20 blue screen of death after shutdown

Hi there,
I get the blue screen of death after shutdown on my Qosmio F20 laptop.
Error is IRQ_NOT_LESS_OR_EQUAL.
I assume that it is somehow related to tv tuner card.
I have tried to restore system - no good. After restoration for some time it was OK. But then BSOD appeared again.
Sometimes it also appears when I connect USB HDDs or even when I insert DVD disk.
And for shure everytime I shut laptop down.
Has anybody got ideas?

Hi
Reading you last message I really dont know what you expect from this forum ?:|
We all here can provide only some suggestions and opinions.
Without any notebook tests and checks nobody will be able to provide a magic solution
I hope you understand this.
So back to the notebook issue.
There is a one way to find out if the issue could be related to the software or hardware.
You have to reinstall the notebook with the Toshiba recovery CD. If the same BSOD will appear after the installation from the recovery CD then the chance are that the hardware is faulty!
I think you should check this out.

Blue screen when attempting to use the dedicated video card

I keep getting a blue screen when attempting to use the dedicated video card.
I managed to install the AMD driver for it but without the other components like the Catalyst Control Center as it blue screened on startup when attempting to load the Catalyst Control Center.
The OS loads fine. Any applications that don't use the dedicated video card runs fine. All other drivers install fine as well.
Applications like games and Photoshop that switch to the dedicated video card on startup automatically crashes, the OS freezes then a blue screen appears.
What could be causing the problem? This problem just recently appeared. Two weeks ago.

boogs wrote:
I tried installing the drivers for my laptop from HP's support site. Still the same result.
This problem only appeared a few weeks ago. Before that, the same drivers from the HP site installed and functioned normally.
Could this be a problem with the graphics card itself?
Note sure but if we can know the system P/N others can look to see what drivers it has for the graphics to know what is there.
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

To make sure that this is not software related, set it back to factory settings, without using any backup data afterwards. Set up the rest of the personal settings manually and test the phone. If it still does not work, this is a hardware issue and the phone has to be serviced by Apple or an Authorized Apple Service Provider:
Use iTunes to restore your iOS device to factory settings - Apple Support
Find an Apple Authorized Service Provider
iPhone - Contact Support - Apple Support

After using Nokia Software Updater my preffered la...

Hello everybody,
I use Nokia E51. "If my Russian language is no longer available after using Nokia Software Updater, I need to return my Nokia E51 to a Nokia Care point to have this language reinstated." But I don't know where is Nokia care point and is it possible to reinstate, if I tried to update second time after language was missed?
Please help me,
Sicerely yours)))
Garry

Common problem
you phone was an import originaly meant for another market,
either the importer or retailer added the russian language pack before selling it on
When you connected your phone to NSU it looked at the product code then installed the firmware for its orignal region
this overwrote the installed languages
the only legitimate way of getting your russian language back is to go to a nokia care point and pay to have them do it
You can find your nearest care point by using these links:
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

Blue screen on restart after 10.4 install

i have an ibook and tried to upgrade to 10.4 from 10.2.8. after having to try twice to install 10.4 (i kept getting the "try again" error message), it worked. but on restart, after the grey "OS X" screen, it goes to a blue screen and just sits there like it's finished starting up. the screen saver even goes on after awhile.
any help will be greatly appreciated!
ibook Mac OS X (10.4)

You could try to boot with Command-V and see if anything relevant shows up there (verbose boot mode).
Where does the CD you use to install comes from ? Is that a retail version or one delivered with another machine ?
If you have another mac, you can try to apply the combo update 10.4.8 to your system (attach your sick mac's hard drive by booting it in Target mode ("T" key at early boot state).

Satellite P20-771: Blue screen error message after OS reinstalling

I have a laptop Satellite P20-771 / Pentium 4 3.40GHz (800/HTT) / XP Home/ 17' with nVidia Geo5700 driver.
As I had some problems with software, and I reinstalled everything using the provided CDs. Unfortunately the computer keeps malfunctioning giving me blue screen errors, that are due (this comes out when I sumbit the error to Microsoft) to device drivers. I updated everything (I hope) from the Toshiba page, but I am not an expert and I am worried that I missed something or that something has not been loaded in the right order or that the setting are incorrect.
Thank in advance for your help
Roberto

Hello
I have also P20 (red one) and have never had any problem after using provided recovery media. According to your posting there must be two possible reasons for blue screen:
1. you have installed some additional software that causes bluescreen or
2. there is some hardware component responsible for that (new memory module or maybe some external device connected to the unit)
Sorry but I dont see any other reason. On this way it is not easy to give precise answer and we can just speculate why this happen.

Blue screen of death after installing Boot Camp on Windows 7

Hello and thanks for the help!
Brnad new user to Boot Camp here. After a new install of Windows 7, I install Boot Camp but then when rebooting Windows I get the blue screen of death. When letting Windows attempt a repair, it fails and I am forced to Recover Windows 7 to a state before I installed Boot Camp.
Help!?

Solution for this problem is simple. You have to apply Mac Book Air SMC Update 1.7 which you can do from Mac OS X with Software Update or you can download required update manually from Apple support site. If you don't use BootCamp and have installed Windows without it, you will have to boot Mac OS X from external drive just to apply required update. After you applied SMC update, you can boot to Windows and apply BootCamp update 3.2 and 3.3.
There is a known problem with Mac Book Air EFI Update 2.3, which you won't be able to apply and it will show in Software Update every time you check for updates. There is no solution for it yet.
You get BSOD if you have BootCamp 3.1 and Windows 7 SP1 installed and you have commited Windows update which will break applemtp.sys as your SMC firmware is too old. It applies to Windows 7 32 bit and 64 bit versions in BootCamp or native install.

Blue Screen of Death After Trying To Install Windows On Pavilion ze4900?

After my hard drive died in my Pavilion ze4900, I replaced it with another notebook hard drive I had laying around.I also tried installing Windows XP home from a Windows installation CD, the same OS the laptop had before the hard drive died. All went well until the laptop was done loading all the installation files, instead of giving me the option to either install Windows or repair Windows, the laptop ends up showing me a blue screen with the message: " A problem has been detected and windows has been shutdown to prevent damage to your computer." What can I do to resolve this issue? I have installed Windows XP on another computer using the same CD, so the CD hasn't gone corrupt and the replacement hard drive is barely used. Any help would be greatly appreciated!

, Hello and thanks for posting on the HP support forums. The first thing you will want to check is if there are any issues with the hard drive you put in. Run the BIOS diagnostics for the hard drive and the hard ware to make sure there are no issues. HP Notebook PCs - System Diagnostics (F2) And. HP Notebook PCs - Testing a Hard Disk from the BIOS Please let me know how things go. Thanks again for posting and have a great day.

Blue screen of death after update

I just recently received notification that there were updates for my iMac 700. After checking to be sure what the updates were (iTunes and OS security update) I clicked on Update. Not long after this started I was called away for several hours and on return and waking the computer from sleep (options set for 3-screen saver, 5-turn off screen, and 10-sleep) I noted the expected notice about restarting the computer to finish the installation. I clicked Restart and then had to divide my time between two computer almost adjacent to each other. After several minutes when I expected the computer to have finished the install and restarted, I checked and only a blue screen with the spinning time marks were showing. As I watched the screen went black for several seconds then the Blue Screen and Time Marks returned. This same scenerio happened several times over the next hour telling me there was something wrong with the OS and because of lateness I decided to wait until the next day to check the computer. The next morning I turned the computer back on and watch as the blue Apple screen came up for a short time then the spinning Time Marks came on. This lasted about 5 minutes then the screen went black for several seconds (previous was for shifting between multiple updates) but after this happened several times it indicated there was definitely something wrong with the OS. I pulled out my OLD original Tiger (10.4.0) install disks and opened first aid>disk check and ran the disk verification which passed with no notices whatsoever. I then started to re-install 10.4.0 but when it notified me that it could not install because there was newer version of os (10.4.11) installed and to use Options. I quit out of this because one of the options was to erase the disk and because of the install failure in this manner would be unable to backup what was on the computer. I then pulled out the Apple Care disk that came with the computer but that was in classic (9.2) but had not fully loaded after almost a half hour so discontinued the load. What is the data integrity safety factor in reloading 10.4.0 using the save data option as this is the only thing I can see to restore the computer at this time.
Sparkgapper

It appears to be time for a relatively painless Archive & Install, which gives you a new/old OS, but can preserve all your files, pics, music, settings, etc., as long as you have plenty of free disk space and no Disk corruption, and is relatively quick & painless...
http://docs.info.apple.com/article.html?artnum=107120
Just be sure to select Preserve Users & Settings.
I only use Software Update to see what is needed, then get them for real via...
http://www.apple.com/support/downloads/
That way I can wait a week or so, check the forums for potential problems, and get Permissions & such in order before installing.

Skype causes Blue Screen of Death after a while in...

Hello, I'm currently having a problem with my skype where it will cause my computer to BSOD after a while in a call, it's only happening during skype calls, not during other voice communication programs like steam's voice calling and the blue screen is more likely to happen when I'm running Firefox.
The Blue screen error I get is "Clock Interrupt was not receieved on a secondary processor within the alloted time interval."
Any help would be appreciated.
Solved!
Go to Solution.

The issue might be triggered by Skype and other software but definitely not due to Skype. It's a very broad multiple CPU timing's issue that can be caused by several things.
1. Problematic BIOS settings
2. Failing hardware/drivers
3. CPU/Fan/HW monitor control programs
4. Power management settings
As a temporary workaround you can try setting the processor affinity for Skype or set your Windows to boot off only 1 CPU using msconfig.
http://www.addictivetips.com/windows-tips/how-to-set-processor-affinity-to-an-application-in-windows...

Flashing blue screen on startup after unplug

MacBook Pro - Leopard 10.5.8
After closing MBP, thus sending it into a state of sleep, I accidentally unplugged it. (No battery.)
When I turn it on, it goes past the Apple logo to the blue screen and keeps flashing two shades of blue, with an occasional loading wheel.
-I've repaired disk and disk permissions via OS Disc.
-I flashed the PRAM.
-I can boot XP Bootcamp partition.
-I cannot Safe Boot.
Any ideas?

I am now running 10.6.8 off an external drive. I copied my Applications and pretty much everything from Library folders that weren't Apple system stuff (it wouldn't let me replace those). I just tried to open Pro Tools and it can't because something is missing. Any idea what this might be and if it might be something I should try to salvage from the corrupt system drive using Data Rescue?
I can reinstall Pro Tools from scratch, but I'd rather not if I can just easily find the files it needs.
Here is the error report:
Process:         Pro Tools LE [2997]
Path:            /Applications/Digidesign/Pro Tools/Pro Tools LE.app/Contents/MacOS/Pro Tools LE
Identifier:      com.digidesign.ProToolsLE
Version:         ??? (???)
Code Type:       X86 (Native)
Parent Process: launchd [124]
Date/Time:       2014-06-13 06:05:47.545 -0700
OS Version:      Mac OS X 10.6.8 (10K549)
Report Version: 6
Interval Since Last Report:          5528 sec
Crashes Since Last Report:           234
Per-App Crashes Since Last Report:   1
Anonymous UUID:                      B4863945-9577-4D54-832E-BDC91F92DD76
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: @executable_path/../Frameworks/CFnd.framework/Versions/A/CFnd
Referenced from: /Applications/Digidesign/Pro Tools/Pro Tools LE.app/Contents/MacOS/Pro Tools LE
Reason: image not found
Binary Images:
0x8fe00000 - 0x8fe4163b dyld 132.1 (???) <4CDE4F04-0DD6-224E-ACE5-3C06E169A801> /usr/lib/dyld
Model: MacBookPro5,1, BootROM MBP51.007E.B06, 2 processors, Intel Core 2 Duo, 2.8 GHz, 4 GB, SMC 1.33f8
Graphics: NVIDIA GeForce 9600M GT, NVIDIA GeForce 9600M GT, PCIe, 512 MB
Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.10.131.42.4)
Bluetooth: Version 2.4.5f3, 2 service, 19 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Serial ATA Device: Hitachi HTS723225L9SA62, 232.89 GB
Serial ATA Device: HL-DT-ST DVDRW GS21N
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0x24400000 / 3
USB Device: External USB 3.0, 0x0480 (Toshiba America Info. Systems, Inc.), 0xa006, 0x24100000 / 2
USB Device: USB 2.0 Hub [MTT], 0x1a40 (TERMINUS TECHNOLOGY INC.), 0x0201, 0x26200000 / 2
USB Device: USB 2.0 Hub, 0x1a40 (TERMINUS TECHNOLOGY INC.), 0x0101, 0x26270000 / 8
USB Device: iLok, 0x088e, 0x5036, 0x26271000 / 11
USB Device: Composite Device, 0x059b (Iomega Corporation), 0x0370, 0x26272000 / 10
USB Device: WD10EAVS-00D7B1, 0x13fd (Initio Corporation), 0x1340, 0x26273000 / 9
USB Device: My Book 1140, 0x1058 (Western Digital Technologies, Inc.), 0x1140, 0x26260000 / 7
USB Device: My Book 1140, 0x1058 (Western Digital Technologies, Inc.), 0x1140, 0x26210000 / 6
USB Device: My Book 1140, 0x1058 (Western Digital Technologies, Inc.), 0x1140, 0x26230000 / 5
USB Device: FA GoFlex Desk, 0x0bc2 (Seagate LLC), 0x5071, 0x26240000 / 4
USB Device: My Book 1140, 0x1058 (Western Digital Technologies, Inc.), 0x1140, 0x26220000 / 3
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0236, 0x04600000 / 3
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x04500000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 / 2
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8213, 0x06110000 / 3
FireWire Device: 003Rack, Digidesign, Up to 400 Mb/sec
FireWire Device: FreeAgent FW, Seagate, Up to 800 Mb/sec

Blue Screen Issue started after warrenty over

Hi I bought HP laptop and exactly after warrenty period there is some problem.
And HP customer support provided many drivers to install but non is working out.
Seems that if we have extended warrenty we will be getting the right driver to install.
My previous laptop was HP, so i got another. and now i will not repeat this mistake.
Any soln for blue screen.
Regards...
This question was solved.
View Solution.

OK, stop 0x0116 indicates a problem with your graphics driver.
I suggest you boot your system in safe-mode (hit F8 repeatedly prior to the windows loading screen pops up, and you should get a startup menu. Select boot to safe-mode. Starting the system in safe-mode should work, and you should then be able to uninstall your graphics drivers.
After uninstalling reboot normally and reinstall using the latest graphics drivers available.

Blue Screen on T60p after using ThinkVantage to update on 5/7/2008

Similar Messages

Maybe you are looking for