Blue Screen, reboots now getting 2 vertical lines

I have the Z10 and I got the blue screen, wouldn't turn back on. Today I got the blue screen. It shut off and restarted, then went blue again after about a minute, restarted and then there were 2 vertical lines (one blue, one white) down the screen. Now it won't go back on at all. Advice?

Well, I had a very similar issue but I traced it to an app. Some people who have gotten the blue screen have pulled their battery before it shut down and apparently that killed the phone. I say apparently because that's what they reported but never followed up on some advice.
Have you tried to see if BBerry link will see the phone?

Similar Messages

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

Reinstall OS X:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

Chose wrong display settings, resulting in blue screen. Now what...

I just purchased a new Mac Mini and connected it to my LCD TV with an HDMI cable. Everything was working fine untill I switched the display setting from 1080i to 1080p (or vice versa, I'm not sure) which resulted in a blue screen. Now I can no longer see my desktop, how do I fix this ?
Nevermind. I just found the solution in another topic. Starting the Mac in safe mode solved my issue.
Message was edited by: ScorpioLoco

Hi,
I've also had the same problem you've mentioned and had it kind-of resolved.
I had the horizontal grey area on my screen which got worse over time. I had it sent away to Apple to be repaired and it came back pretty much the same as they couldn't find anything diagnostically wrong with it. I then went to the Genius bar and, fortunately, they recognised that there was a grey banding and replaced the LCD panel.
This did get rid of the grey banding, although brought a whole new set of problems.
Don't put up with the genius staff trying to baffle you or make you feel like you are being silly for complaining - the iMac is not a cheap machine and you have the right to make sure it is fit for purpose. A grey/uneven screen is not fit for purpose.
Ask them to replace your LCD panel and glass, but inspect it when you collect it to make sure it is an even brightness and colour. My replacements have been brighter on the left hand side than the rest of the screen or had a blue tint on the left or a yellow tint on the right. If you don't like it, don't accept it - as I have been told repeatedly by Applecare and the genius bar 'all the lcd panels are different you have to find one you like' i.e. put up with!
Eventually the cost of the replacement panels will mount up and they will offer a replacement. It has taken me almost a year to get my replacement. Just keep on at them until it is resolved.
Also, on your first pic there is a rectangular mark - this could be screen persistance and can be easily removed by using a white screensaver for a few hours. I found mine did it when i had the brightness on full (to compensate for the greyness!).
Hope this has helped, good luck!

When i turn my ipod on i get purple vertical lines and thats all it does, what is wrong with it?

When i turn my ipod on i get purple vertical lines and thats all it does, what is wrong with it?

It may have a bad display screen but you could try resetting to see if that helps.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds).

Annoyingly Blue screen reboot

Haven't seen this topic yet... I am having a blue screen reboot problem. It happens ONLY when you are closing down a program. But randomly. Could be 3 - 4 times an hour, or 1 time an hour who knows whenever it feels like it...Any ideas???
BTW I have MSI K8N Neo 4 Platnuim Motherboard
AMD 64 3200+ Processor
Kingston Value ram 256X2
Antec 550 watt total control PS
ATI Redeon X700 pro 256 mem video
6 total fans running
Seagate 200 GB SATA HD
Creative 12X ovation cd/dvd
Pioneer A07 DVD-R burner
Also I have reloaded 4 time now in three days. I had a Nvidia 6200 video card prior to this. Thought it may be that. Starting to think it may be an overheating problem. Don't know which utility works best for managing temp and fan speeds. Fans run full speed all the time. Lets say about 2800 rpm. Not sure how to increase them
Any other info needed please ask.
This one is driving me up the wall!!!!
Thanks
Dave
:stop:UPDATE!!!!! Well it crashed again. This time upon reboot I got a message about the file called SYSTEM in the Windows32/config dir was corrupt. I could try to repair. It didn't work.. SO instead of reloading all that again I changed the HD to a UDMA 40 GB Seagate. Have been loading software half the day now with no problems. It is alot slower but no errors. Went on Seagate Web site and read about the SATA drive. No where did it say anything about having to load RAID drivers. It says that windows will recognize it as long as you have the LBA mode selected. No my question is : Will it hurt anything without the RAID drivers ?? ANYTHING!! And has anyone out there had this kind of problem as I entered above??? Please someone help.. I am almost bald!!!!!

Might be some Windows file corrution. Suggest you repair your Windows installation.
[How to Repair your Windows

TV Screen says "No signal" when I try to use apple TV. Was working. ie Little Apple symbol would appear on TV screen, but now get "No signal" Internet connection working (light on apple TV)...tried new HDMI cable but still "No signal"

TV Screen says "No signal" when I try to use apple TV. Was working. ie Little Apple symbol would appear on TV screen, but now get "No signal" Internet connection working (light on apple TV)...tried new HDMI cable but still "No signal" HELP please

Same exact problem with my Apple TV. Worked like a charm the first two times we used it. Haven't used it in about a month, now no Apple logo when I turn it on, or the logo appears momentarily and distorted, and then an error message from my Samsung HD TV: Mode Not Supported.
What changed?
Bill O'Rourke
***@***********.com
<Email Edited by Host>

Black screen with a thick white vertical line down the middle?

I turned my iPod touch 5 off, it was at about 10%. I turned it back on a few minutes later and there was the apple logo, as usual, but with small white writing on the black background. Then, I plugged it into my charger, and the logo and writing faded away. Instead, there then was a black screen with a thick white vertical line going down the middle, and it seems to be stuck like that. What happened and how do I fix it??
Note: My home button is stuck and does not work. Also, I never updated my iPod to iOS 7.

Try:
- iOS: Not responding or does not turn on
When it says place the iPod in recovery mode,
Place the iPod in recovery mode using one of these programs:
For PC
RecBoot: Easy Way to Put iPhone into Recovery Mode
or
http://joshuabailey1997.wordpress.com/2010/09/02/recboot-v1-3/
If necessary:
Download QTMLClient.dll & iTunesMobileDevice.dll for RecBoot
and
RecBoot tip
RecBoot may have problems on 64X windows, then try:
Tenorshare ReiBoot – Enter & Exit iPhone, iPad, iPod Recovery Mode with a Single Click
For MAC or PC
The Firmware Umbrella - TinyUmbrella
Installs blootware on PC too
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

HT4528 my month and a half old iphone 5s had a blue screen and now just has a black screen. will not reboot or restore through itunes. what do i do?

my iphone 5s has been showing a blue screen and shuttiing down. yesterday night it did just that and now will not reboot or even restore through itunes.
what should i do?

Your iPhone is in recoverty mode at the moment so to possibly get it back up and running you would need to do a restore as you have been trying. Follow the steps in the article below for the specific error messages you have been receiving. If after following all steps the issue remains book an appointment at a local Apple Retail Store to have the iPhone evaluated.
Resolve specific iTunes update and restore errors

HELP Iphone 5s random reboots, blue screen reboot and now stuck at black apple screen.

I recently purchased a iphone 5s and after about 2 weeks it has started to randomly reboot. It then progressed to rebooting with a blue screen. Attempting to fix the problem I connected the iphone to my computer which told me the backup was corrupt. As I attemped to delete old backup my phone rebooted to a black screen with a bunch of white writing saying things like panic. I have attempted to hard boot the phone many times and it will not go past the black screen with the apple logo. Please help.

Nothing happened, i managed to get my computer to recognise it and now restoring... but it says 3 hours remaining?! Will i lose everything?

My computer keeps showing a blue screen everytime i get online and says memory dumping error

what should i do when my cpu keeps turning off everytime i turn it on and go online. plus their will be a bunch of pop ups that just open up without my permision

Hello gsxbilly750:
         Welcome to HP's forum and malware / virus world oh what fun. First thing is to get your comperter in safe mode. Seeing it has start up issue already I dought if F-8 key will work. So we will do a fource shut down. Turn on your computer let it go to Windows screen then just disconect the power cord from power supply box. Whait until your computer is completely shut down. Now reconnect the power cord and turn on your computer. Use your arrow keys and select safe mode with net working. If this just started happening yesterday then open up Recovery Manager and Select Microsoft System Restore. Click yes in white box click next eventually you will get to a date list choose a date before this happened click next. Let it complete system restore. This is will fix your issue some times. Depends on how much damage was done by malware or virus. If to much damage was done then you need to do a complete system restore. With blue screen of deaf you might have to. Follow the same steps above but select System Factory Restore.
          If you prefer to try cleaning your computer with out doing systems restore. You first need to download Malwarebytes http://www.malwarebytes.org/lp/malware_lp/?utm_source=adcenter&utm_medium=cpc&utm_term=malwarebytes%... Ounce downloaded the trial verson. Type in services in All program search box and open services. Look for your Anti Virus software in list you need to change it from start to stop. Do not close out service window leave it opened. Now open up Malwarebytes and run the scan. Ounce scan is done click fix or delete effections. Then ounce that has been completed you need to uninstall Malwarebytes. Malwarebytes is unistalled. Go to Services window and find your Anti virus software and change it back to start. Close out services window now. Open your Internet Explorer Browser goto tools select Internet Options . Click on Advance tab. Click reset. Close out Internet Explorer and reopen it goto tools again select Internet Options now check mark box delete on exit . Click on Advance tab go down the list and check mark box under securty section Epmty Temporary Files when browser is closed.   click ok. Then click on tool and select Managed Add ons then enable your tool bars ones that you realy need. This now has fixed your Internet Explorer issue. Ounce you fixed these issues reboot your computer.
          If you are still having troubles with bl7e screen Let us know. Thank you frrw.

Constant Crash / Blue screen reboot

I just purchased this P505-S8010 2 weeks ago Everything was great for the first couple of days. Then it crashed and rebooted I didn't think about now 2 weeks later its crashing all the time. Does any one have a clue? Or should I just return it and start over. I have installed Office 2007, Adobe Photoshop and Corel draw. that's it. HELP?

If you can, return it. Run to the store to return it. My P505 has been blue-screening since March and will be going back for it's 4th visit to the repair depot. The longest I have had it before shipping it back was 2 weeks. the shortest was 5 minutes. I'm told they will not extend the warranty and until such time as Toshibe decides it is not repairable, I will get neither a replacement nor a refund, we just continue the cycle of I call, they send a box, I send to them, they take less than a day to fix, send back to me. Only people profiting from this is UPS and ASUS, whom I bought a netbook to use while mine spends to much time traveling the country.

Screen fields not getting displayed after Line 16

Hi All,
There is a screen exit created in IW51, now the new requirment is to add 3 more fields. I added the fields below the exiting fields, in line number 15 , 16 &17. After executing the Tcode I could find that the field created in line 17 is not getting displayed in runtime. I have increased the screen length. The fields if moved to line numbers below 16 then they are getting displayed. Can anyone help me to find why it is not getting displayed after line 16.

Hi,
Can you give me the Enhancement name?
I searched for the exits using package , but i did not find any screen exists for that IW51 Tcode?

Hotspot cause Blue screen & reboot on laptop why??/

When I use my Razor Maxx HD as a hot spot with my laptop, the laptop goes to a blue screen and reboots. What do I do????

EDIT:
I just kept rolling back the driver until I got to 15.2.0.19 and it worked.
Thanks everyone!
===========================================================================================================
I'm having the same issue with the same wireless card in my work laptop.
Can you tell me which driver version now works for you? I don't see any updates, so I might be on the latest right now (15.3.1.2).
The hotspot worked on my previous laptop, but I just got this replacement and the BSOD appears every time that I try using my Droid Incredible 4G.
Thanks!

My acer laptop turned screen into pink and with vertical lines...what's wrong

Hi everyone!I need your help. I bought my acer laptop 7 months ago. I was browsing online then suddenly the screen turned pink and it got some vertical lines now. I tried to removed the battery and pressed the power button for a minute but still the screen is pink when i turned it on. I've noticed the vertical lines are moving every 5 munites. Please help...im stressed with this laptop! last month acer replaced the Hard drive because it went very slow and then now another problem arise.

i already tried to move or tilt the screen and even press it but still the screen is pink... Yes perhaps I need to bring this again at the service center Thanks!

Glowing black screen during charging? White vertical lines

Hello all,
Last week i updated my pb to os 2.1 and everything went well. But now I am facing another problem. Sometimes (not always ) when I charge my pb (completely turn off) then the black screen starts glowing during charging and it keeps on glowing throughout the charging period and my pb becomes very hot. And when I turn on my pb after this then white vertical lines appear on the half portion of the screen. The screen also develops white patches but these patches and lines disappear after 5 minutes of usage.
So why is it happening? Is there any problem with my pb? Help someone
Thanks

Hi abhibharti,
Please contact our direct BlackBerry® PlayBook™ tablet support team for further investigation into this issue. You can find the contact information here: http://bbry.lv/JRKRGm
Thanks.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

Blue Screen, reboots now getting 2 vertical lines

Similar Messages

Maybe you are looking for