Blue Screen While installing XP on my GX630

Hello
I seem to be having an issue installing either Windows XP 32/64 bit on my brand new GX630
When i put the disc into the computer it begins to load and just before the part where u hit F8 to agree to microsofts agreement i get a
Stop 0x0000007B (0xFFFFFADF90C323C0, 0xFFFFFFFFC0000034, 0x000000000000000, 0x0000000000000000)
blue screen.   Has happened to me every time ive tried it on both XP 32 bit and 64 bit.
i did some research on this and this is what i got
Quote
The Stop 0x7B message indicates that Windows XP has lost access to the system partition or boot volume during the startup process. Installing incorrect device drivers when installing or upgrading storage adapter hardware typically causes stop 0x7B errors. Stop 0x7B errors could also indicate possible virus infection.
The second parameter is very important because it can indicate whether the 0x7B Stop message was caused by file system issues or problems with storage hardware and drivers. Values of 0xC000034 or 0xC000000E typically indicate:
• Disks or storage controllers that are failing, defective, or improperly configured.
• Storage-related drivers or programs (tape management software, for example) that are not fully compatible with Windows XP Professional.
Would i have to remove the partitions on the harddrive?
Or has anyone else had this problem?
I have no issues at all with Vista other then the fact that its vista...............
p.s. id like to keep the restore partition on the harddrive.
thx for your time.

you've done well

Similar Messages

  • Mac gets blue screen while installing Windows 7 with bootcamp

    I had a problem while trying to install Windows 7 Ultimate 64-bit on my MacBook mid-2010.  When i would create the partition using bootcamp assistant and my computer restarted into the install process, i would get a blue screen.  The blue screen would occur after my computer restarted and was completing the installation.  If I try to reboot the machine, it gives me an error "The computer restarted unexpectedly or encountered an unexpected error.  Windows installation cannot proceed.  To install Windows, click ok to restart the computer, and then restart the installation."  I first tried this on yosemite, but when it was not working I tried wiping the hard drive and i installed mavericks.  I got the same problem, so it does not have to do with the OS.  I have installed Windows 7 32-bit on this computer before.  But i still get the same error with 32-bit also.  I know that this computer supports windows 7 and 64-bit too.  If anyone know why this might be happening and how i can fix it, please let me know.  Thank you. 

    It is good to see that it is indeed a USB2.
    The support software on the USB is used in the Pre-boot environment setup and provides drivers for Apple specific hardware, GPU, BT, Mouse, etc. You can verify that by looking at the USB contents. The DVD contains generic drivers when hardware is not recognized as defaults to use. Apple does enough 'secret sauce' to make them different. The following does not explicitly state the USB2 need when using the DVD Installer and mentions W8 (not W7).
    From Boot Camp: Creating an ISO image from a Windows installation DVD - Apple Support
    Insert a blank USB 2 flash drive that is a least 16GB in size into a USB port on the computer. Boot Camp Assistant uses this drive to store the Windows 8 install media and support drivers during installation of Windows.
    Note: This flash drive needs to be formatted for the FAT32 file system and must use the Master Boot Record partitioning scheme. Use Disk Utility to check the format of the flash drive before proceeding, and partition or erase the flash drive if necessary.
    I suspect the GPU is not getting the correct driver and the Installer fails. The Generic VGA should work. From the OS X side, can you see files in your BC volume? If yes, can you look for logs in the BC volume at the following locations.
    ./Windows/Inf/setupapi.dev.log
    ./Windows/Inf/setupapi.offline.log
    ./Windows/Inf/setupapi.setup.log
    ./Windows/Logs/SetupCleanupTask/setupact.log
    ./Windows/Logs/SetupCleanupTask/setuperr.log
    ./Windows/Panther/FastCleanup/setupact.log
    ./Windows/Panther/FastCleanup/setuperr.log
    ./Windows/Panther/setupact.log
    ./Windows/Panther/setuperr.log
    ./Windows/Panther/UnattendGC/setupact.log
    ./Windows/Panther/UnattendGC/setuperr.log
    ./Windows/setupact.log
    ./Windows/setuperr.log
    ./Windows/System32/Sysprep/Panther/IE/setupact.log
    ./Windows/System32/Sysprep/Panther/IE/setuperr.log

  • Blue Screen while Installing Win XP on T510

    Hi
    I am getting Blue Screen Error while Installing Windows XP Pro on ThinkPad T510 during setup. It comes after Win XP's disk has loaded all the drivers and files to start installation. It can load Win 7 and Run but not XP or Server 2003
    "A Problem has been Detected and Windows has been shut down....
    Tech Info
    ***STOP: 0x0000007B
    Any help please? Thanks
    Solved!
    Go to Solution.

    You needs this driver http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70477
    when installing Windows XP you will see probmt to press F6 to add 3rd party driver using floppy disk... yes that right a floppy disk only option!.
    or you can add driver to Windows XP cd using Nlite program. www.nliteos.com
    maybe the easies option is to change AHCI option from bios that you have already did.
    i havent seen any performance issues if XP uses compatibility mode.

  • Adobe Creative Suite 5.5 Master Collection turns into blue screen while installing disc #2

    I purchased a windows version of Adobe in Sep this year.
    I have tried more than 4 times, but still can't install the software.
    My laptop turns into blue screen and restarts itself after the system tells me to insert second disc to continue the installation process.
    I had the extact same version of Adobe installed on this computer before, but I can't seem to install the software again after recovered my computer.
    computer spec:
    Win7 Home Premium
    Service Pack 1
    i5-2410 @ 2.30GHz
    64 bits
    8GB RAM
    500GB SATA
    Thank you so much and appreciated if anyone or the actual Adobe tech can solve my problem.

    Hi Mylenium,
    Thank you for taking the time to read over and answer my question.
    However, I don't think this is a driver issue. I actaully had the following softwares installed from the disc--- Adobe Audition CS5.5, Adobe Bridge CS5.1, Adobe Device Central CS5.5, Adobe ExtendScript Toolkit CS5.5, Adobe Extension Manager CS5.5, Adobe Media Encoder CS5.5, Adobe Pixel Bender Toolkit 2.6, Mocha for After Effects CS5.5, Adobe LiveCycle Designer ES2, Adobe Acrobat Distiller X, Adobe Content Viewer, and Adobe Widget Browser.
    Before the installation process started, I chose to install everything that's on the disc.
    But I can't get the softwares that I really need such as photoshop, after effect, indesign, illustrator, and so on.
    Again, thank you for your help,
    Kevin

  • Blue screen while installing Boot Camp support software in Win7 Ultimate x64

    2012 macbook pro with OSX Mavericks. Installing Win7 ultimate x64 using boot camp assistant and a USB drive went flawlessly. Then I downloaded and installed the boot camp support software from support.apple.com/kb/DL1638
    Running setup.exe bluescreens my computer and makes the windows partition unbootable after that, even in safe mode. I performed a system restore to roll back the boot camp software and booted again, and checked the log file. It pointed to an intel USB driver. I then deleted IntelxHCI from the Drivers/Intel folder, ran setup.exe again, and everything installed perfectly.
    My question is: what is the Intel usb 3 extensible host controller, why is it included in the support software, and why does it immediately brick my Windows partition?

    I have re-installed Windows 7 about 20 times already, I am experiencing the same problem as you are. The issue must be some kind of driver being installed by Boot Camp. When I leave my fresh Windows 7 install with no Boot Camp, the error or blue screen never occurs. This is weird.
    Help please Apple...

  • Blue screen when installing Win XP Home

    Getting blue screen when installing Win XP Home on 915P Neo2 Platinum motherboard with the on-board LAN port enabled! Any idea to fix this?

    disable onboard lan then reneable it after you get xp installed see if that works.  try to get the latest bios for your motherboard to.

  • Audigy 4 gives blue screen during install of drivers on Windows XP SP3

    FAudigy 4 gives blue screen during install of drivers on Windows XP SP3! Specs
    Asus a8n-sli
    GB RAM
    6600 GT
    Audigy 4
    LC Power 550 W PSU
    I put in the installation CD that comes with the card. I want to install everything (full install), and mid-install I get a blue screen.
    I then uninstalled everything and tried only to install the updated drivers from the website in safe-mode and still a blue screen. Should I get the dump file and send it to Creative?
    How do get this card to work like it should? I also have a remote control that came together with the card.
    Im currently using the onboard AC97 Realtek ALC850 soundcard.
    Whats the whole procedure to make this work? Detailed please. How do I eliminate all traces of the audigy on my PC?

    Re: Audigy 4 gives blue screen during install of drivers on Windows XP SP38 Perhaps you'd want to read this old thread of mine about my misadventures with the same exact card you are trying to use. IMHO that card was not worth the time and money I spent on it (even even less the time and money it caused me to spend afterwards to repair the damage it caused.
    Message Edited by CreativeSkeptic on 2-23-2008 0:4 PMMessage Edited by CreativeSkeptic on 2-23-2008 0:4 PM

  • I5 17''MBP  gets blue screen during install windows 7 32 bit

    Hello all:
    I heard that quite many people get classic windows' "blue screen" during using windows , whatever Windows XP, Vista or 7. But now i face the "blue screen" during install Windows 7, which means I even can not complete installation.
    I bought my Macbook Pro i5 17'' one month ago, and I'm trying to install Windows 7 but I face the problem during the installation. After finishing first 4 steps the computer would restart and start to "finish installation", but at this time it gets "blue screen" and shows "error: 0x0000009c" and stuck there. I have to shut down the turn off button and interrupt the installation.
    I don't know if there's any one else face this unlucky situation. I searched on the net and it says the problem could be from memory, graphic card (too new), or even overlocking the cpu,whatever it must be the problem of hardware. I thought it might be the problem of compatible.
    If anyone knows how to deal with this problem??!! I do need to use some software under Windows system!

    It is good to see that it is indeed a USB2.
    The support software on the USB is used in the Pre-boot environment setup and provides drivers for Apple specific hardware, GPU, BT, Mouse, etc. You can verify that by looking at the USB contents. The DVD contains generic drivers when hardware is not recognized as defaults to use. Apple does enough 'secret sauce' to make them different. The following does not explicitly state the USB2 need when using the DVD Installer and mentions W8 (not W7).
    From Boot Camp: Creating an ISO image from a Windows installation DVD - Apple Support
    Insert a blank USB 2 flash drive that is a least 16GB in size into a USB port on the computer. Boot Camp Assistant uses this drive to store the Windows 8 install media and support drivers during installation of Windows.
    Note: This flash drive needs to be formatted for the FAT32 file system and must use the Master Boot Record partitioning scheme. Use Disk Utility to check the format of the flash drive before proceeding, and partition or erase the flash drive if necessary.
    I suspect the GPU is not getting the correct driver and the Installer fails. The Generic VGA should work. From the OS X side, can you see files in your BC volume? If yes, can you look for logs in the BC volume at the following locations.
    ./Windows/Inf/setupapi.dev.log
    ./Windows/Inf/setupapi.offline.log
    ./Windows/Inf/setupapi.setup.log
    ./Windows/Logs/SetupCleanupTask/setupact.log
    ./Windows/Logs/SetupCleanupTask/setuperr.log
    ./Windows/Panther/FastCleanup/setupact.log
    ./Windows/Panther/FastCleanup/setuperr.log
    ./Windows/Panther/setupact.log
    ./Windows/Panther/setuperr.log
    ./Windows/Panther/UnattendGC/setupact.log
    ./Windows/Panther/UnattendGC/setuperr.log
    ./Windows/setupact.log
    ./Windows/setuperr.log
    ./Windows/System32/Sysprep/Panther/IE/setupact.log
    ./Windows/System32/Sysprep/Panther/IE/setuperr.log

  • Can anyone help me with blue screen while updating to ios8?

    help me with blue screen while updating to io8.2

    I don't have a 4G device, but I thought you can use mobile safari, the safari on the iPad, on 4G.
    You could also try looking for a third party app. The official facebook app has been non to barely functional for years. I use mobile safari on my iPad although I do have a couple  of apps I've used upon occasion.

  • HT4718 My macbook air is stuck at the "installing software updated" screen while installing update for the osX. What should I do?

    My macbook air is stuck at the "installing software updated" screen while installing update for the osX. What should I do?

    Welcome to Apple Support Communities
    If your Mac has been installing software updates for a long time, Software Update is probably frozen. Hold the Power button until your MacBook Air turns off, and turn it on again. OS X should start up.

  • Blue Screen after installing 2nd HD as Slave

    As soon as I installed a 2nd HD as slave, I get the occasional blue screen, with the following:
    MACHINE_CHECK_EXCEPTION
    Stop: 0x0000009C (0x00000004, 0x805366F0, 0xB2000000, 0x00070F0F)
    I have had no problems for the past two weeks until I installed this 2nd HD. By the way, the 2nd HD is relatively new, I have used it in another computer and has never given me problems.
    Here are the steps I took and what I observed:
    1) I BOOT using the 1st HD (PRIMARY). I disabled the 2nd HD from "Device Manager". (Basically, I am trying to isolate the two drives)
    2) Everything is fine. I can work and play games while I am using the 1st drive.
    3) Next, I BOOT using the 2nd HD (SLAVE). I disabled the 1st HD from "Device Manager".
    4) Problems begin. I get that Blue Screen - sometimes during the BOOTING, sometimes while I am working in windows.
    It seems to come down to something going on with the "slave channel"
    I have installed the NVIDIA CK8S Parallel ATA Controller (v2.5) as well as updating to (v2.6).
    Here are my system specs:
    OS: Windows XP (All updates, excluding service pack 2)
    AThlon64 2800+
    MSI K8N Neo Platinum (MS-7030)
    1 GB OCZ PC3500 memory
    ATI x800pro
    Western Digital WD800JB (Primary)
    Western Digital WD800BB (Secondary)
    Audigy 2 ZS
    Please Help!

    well, as I suspected you have 18amps on the 12v rail, same as me, I get those same errors when burning a DVD from an ISO, (got the BSOD 3 times actually), doing the same thing, and the other day I got it while surfing, I have a high quality PSU, a thermaltake 480 but unfortunately it has also 18amps on the 12v rail, so I'm waiting to duplicate the BSOD and take out some parts to see if the problem remains...
    I did this the other day to check how much current I was using.. I don't believe this is not even 90% accurate, but at least to give you an idea..
    AMPS
    7.73 - cpu
    0.30 - mother
    0.25 - system fan
    0.25 - 2nd system fan
    0.25 - PSU Fan 1
    0.25 - PSU Fan 2
    0.25 - cpu fan
    2 - 2x ide HDD
    0.85 - DVD Drive
    0.75 - DVD RW Drive
    13amps  === Total
    Now, if you have a 18amps power supply remember that those specifications could be under ideal conditions, (no heat, etc). I assume that what mine is really providing is something between 13 - 15 amps, yours could be even lower, do you have another PSU you could try with? (I don't, so I haven't had the chance),
    Also, if that doesn't help, try removing all the other components from your system, and leaving only the most basic stuff,,,e.g. remove fans (leave cpu fan of course), cdrom, dvd, floppy, video card, etc etc, leave just the two harddrives.... please let me know if that solved the problem for I'm also thinking about getting another PSU.. but wanted to make sure before..

  • Blue Screen When Installing Boot Camp Updates

    For some unknown reason, whenever I put in the OS X install disc in order to use my internet, wireless mouse, etc. The Blue Screen of Death or what I believe that to be, pops up for an instant and then my computer immediately restarts. I've tried this 5 or 6 times and finally decided to make a post. Thanks in advance.

    Everyone is having that issue. There seems to be a major bug with the bluetooth Boot Camp / wireless drivers where you get a blue screen of death whenever your computer has been idle for a while and then you start typing on the wireless keyboard.
    Wish Apple would fix this problem - my computer crashes several times a day.

  • Blue screen while working

    Hello everyone, yesterday i had 3 times cpu panik so i decided to make a clean install of the OSX on my computer. While i was watching a video on youtube (after the clean install) the computer displayed a blue screen (see images) and in order to remove it i have force the computer to reboot. Does any one know whats the problem?
    I want also to mention that the summer i have changed the logic board twice for the same problem.
    My previus post : https://discussions.apple.com/message/23969484#23969484

    Insert your original installation disk and follow the Hardware Test instructions, if possible.
    Otherwise take it in for servicing.

  • Blue Screen while working on my iMac G5 17", 2GHZ

    Hello
    I wonder if my onboard graphic card in my iMac G5, 2Ghz, 17" is broken
    While working a display filling blue screen appears during 2-3 seconds. After that incident, my deskop wallpaper is gone. Also the iMac becomes very slow. I've resettet the PRAM, reinstalled the system (archive & install) and exchanged the RAM modules. Nothing helped.
    Is my graphic card broken?
    What can I do?
    Hossie

    Insert your original installation disk and follow the Hardware Test instructions, if possible.
    Otherwise take it in for servicing.

  • HELP - Laptop constantly blue screens since installed new E4200

    I posted earlier about problems with a laptop connected to an E4200.  I am connecting to our wireless network and then using AT&T Global Dialer to access my company's network via VPN.  I have two desktops using the wireless network with absolutely no problems but the laptop constantly blue screens and/or loses the VPN connection.  This started the day we installed the new router.   Today I noticed that when I view all of the available wireless networks on the laptop, I see two of them for our home network (in addition to all of my neighbors' networks).  The duplicate SSID's have different MAC's and are on different channels.  Could this be causing my problem?  We had an older Linksys router prior to the E4200 and had absolutely no problems with the laptop.  Is this because the E4200 is dual band?  Would I be better off without this feature? 
    When I view the available wireless networks on my desktop, I only see the one home network, not two.  I also see only one of our neighbors' instead of six or seven (not sure if this is significant).  I don't know why the laptop sees two but the desktop sees one.  Any suggestions from anyone for this?
    I called technical support and all they wanted to do was sell me an extended warranty.  She wouldn't or couldn't answer my question about why the laptop saw two SSID's for my network and whether this could be causing me problems.

    Well, I connected the laptop to the guest network and haven't had any problems since.  I left it up about 5 1/2 hours last night and it stayed connected with no blue screens.  So far, so good this morning, although I can't say definitively it is fixed because once it went a whole day without blue screening, and once it only had problems one time during the work day.  However, five to six times a day had become the norm, so I am hopeful.
    I am convinced that the problem is that it could see two networks with the same name.  Probably those are there because it is a dual brand router and one is 2.4 and the other 5 ghz, but I don't know how to tell for sure. 
    I can't change the wifi card on my laptop because it belongs to my company.  I did check to make sure it could handle 5ghz and it can.  I also have the latest version of the firmware.
    I have searched and searched the internet and it seems I am the only person in this world having this problem.  If anyone has any ideas for anything else to check, that would be great, just in case connecting as a guest doesn't work long term.  I did check the settings and they are the same for 2.4 and 5 ghz, so why do I see two networks on the laptop, while I see only one on the desktops?  I am using Thankvantage Access Connections on the laptop.

Maybe you are looking for

  • Contoling structure of view.

    Hi, Can we define the column datatype sizes during creation of view. Let us consider the following view creation script. create or replace view cmonlftWCr select custcd,custnm,excldlryn,exdlrfrm,to_char(billdate,'YYYY-MM') Month, sum(billqty) MthQty,

  • Can someone make iBooks have the Option to view 2 pages in landscape mode so it can use up all the pixel real estate?

    Can someone make iBooks have the Option to view 2 pages in landscape mode so it can use up all the pixel real estate? Apple usually does this for OSX and its great when compared to windows where it doesnt use up all the real estate for viewing applic

  • JDBC Receiver to ORACLE Stored Procedure

    Hi Experts I browed the forum and could not find a strait answer to my problem. Hence I am posting this thread. I have a sync call using JDBC Receiver to ORACLE stored procedure. The definition of the procedure is as follows: CREATE OR REPLACE proced

  • Planning table

    Hello, In planning table MF50 , the row 'not yet assigned ' is displayed from where we can assign plnd orders to any Packign line. But when i assign the qty from this row to any other packing line the qty from 'not yet assigned ' is not getting deduc

  • Tabs on the actual bottom of the page?

    Hi. Is there a way to make tabs appear on the actual VERY bottom of the page? And I don't mean that "bottom" which is still on top, gosh, who named that feature? Basically, I want all my tabs to appear at the bottom but I'm not keen on using any plug