Blue screens with my new P45 Neo3-FR motherboard

Blue screens with my new P45 Neo3-FR motherboard
I have recently purchased this Motherboard and being trying since few overclocking combinations unsuccessfully
I have a Dual Core E8400 Rev.E0 processor and the best I had so far is 3.6 MHz (400x9) at stock voltage.
I am trying to achieve 450 FSB (450x8.5) stable with memory @900 MHz.
I have increased Vcore to 1.28v and 1.31v, Vram is on 1.9v and I left all other voltage settings on Auto.
Disabled CPU C1E function and & Spread spectrum.
As soon as i raise the clock over 400MHz is when the problem start.
Most of the time is happening when the machine has been left (idle) for a while, I just click anywhere,or just start a programme
and suddenly I get a blue screen and the machine re-boot, and again I run Prime for 3 hours (torture test) and not a single blue screen.
Very weird..
I have 2 MB (2 x 1024) dual corsair memory DDr2 PC6400 XMS2 (5-5-5-18) modules and an ordinary Ati Radeon Powercolor HD 3600 graphic card.
I tried to run both memory stick in single mode and one at the time, but still getting those blue screens.
I have built this system re-using a couple of years old power supply from Hyper (505W).
I need some advice as I am trying to establish which component is to blame.
Could this be caused by the PSU, perhaps malfunctioning or inadequate for this motherboard ?
Also thinking about the memory....memory seems running OK till 960 MHz with processor at 400 x 9 (1:1.20 ratio).
Or perhaps is the Motherboard ?
I have Vista Home Premium Edition OS.
Please advice guys.

Hi Guys,
I`ve just updated to Bios v.1.71b
Raised FSB to 445 Mhz and kept multilier to 9x (445 x 9 = 4.005 Ghz)
Vcore to 1.335v
Dram to 1.904v
MCH to 1.304
VTT FSB to 1.34v
ICH still on Auto
Disabled C1E support, Spread spectrum and Intel EIST support.
Set ram to 1:1.00
Tested several times with Super PI & Intel Burn Test and machine is stable so far.

Similar Messages

I was able to use the program before. Now when I go in all I see id the blue screen with the new upgrade info.

I was able to use the numbers program before. Now all I see is the blue screen with the new updates. How do I fix this. I have already downloaded the new version of Icloud & open office $ installed.

Are you talking about doing this on your iphone? Or something else?

How can i get my hp dv-7 to stop blue screening with the new ocz vertex 3 ssd

installed a new ocz vertex 3 ssd on my pavilion DV-7-6b75nr and it will now not stop blue screening.Even took it to a computer shop and they could solve the issue. is this laptop not meant for sata 3 SSD's or do i need a certain one or does hp have to install it? windows7,computer 3 weeks old,I7 processer...using the SSD for my os and main boot drive..Computer shop said i might need to rewrite HPs bios...??

Hi,
You can find the list on the following link:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02763358&tmp_task=prodinfoCategory&cc=us&dlc=en...
Please install the following list:
1. Software multimedia
2. All components of Software solutions
3. Utilities
from the following link:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5064...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Blue Screen with installing new Windows on already pre-installed one

Hello everyone, I am sorry if that topic has already been dealt with, and if I am asking about the same thing. I found a few posts relating to my problem, but it did not fully help, so...
I bought a M70 in Germany, it has Win XP HE already installed, but I wanted to install my Windows with a different language. When I boot the computer from the disk, there is first this blue screen saying that it is loading many drivers, etc. Then, it suddenly stops when it finishes loading all the stuff. There is only a cursor in the upper left corner (the one in DOS operating mode) and nothing happens. What could be a problem?
Is there some kind of blockade on the hard disk preventing me from formatting the partition and installing a different system? My own windows does not include SP2 on the cd, usually I install it later on.
I saw at least one similar post, someone suggested browsing the download section on the website to find some information, but I failed in doing that. Can someone help me? I would be extremely grateful for any information!
mike

Hi guys, unfortunately, I am still in Germany, and I have limited access to any windows software. I can use a Win XP SP2 install cd only when I go home next month, so right now I am trying whatever else I can. I thought of installing the Windows from the recovery cd on another partition, but it stubbornly wants to do it on the main one, wanting to completely remove everything from the main partition. At least, then I could format the C partition using Windows installed on another partition, but it does not work anyway. I guess I have no other choice but to wait until I have access to a cd with Win XP SP2 on it. I really hope that is the cause of the problem. I will try to get any other copy of Win just to try it out, and I will keep you guys informed. If you have any other ideas, share them with me, please.
Regards, Mike.

Stuck on blue screen with clouds rainbow, floated ...

As it says.
When I start Skype, it goes straight to a blue screen with blue clouds and a green rainbow at the bottom. I get no prompt to login. I have followed various guides, such as renaming login to login1, deleting login, restarting the computer, uninstalling then installed skype (which gets me an error code 2734 I think), uninstalled and installed Internet Explorer. I have run windows update and everything is up to date. I also followed the advise in the floated topic, and even after using Command Prompt (which was not in Accessories folder, had to search cmd to find it) and restarting, the 'click this button' does not work.
Skype was working fine on Sunday, and now it is broken. The only thing I have done in the meantime is run a repair tool for Windows Media Player as a game I installed required it to play in game music.
EDIT: I use Windows 7.
Solved!
Go to Solution.

Scripting in Internet Explorer might be disabled by an Antivirus software. What Antivirus software is installed on your computer?
Meanwhile you can try the “legacylogin” workaround, which should enable login to Skype using the old legacy login window. However, you will not be able to login using Microsoft account (email address).
Quit Skype. Make sure that you don’t see any Skype.exe processes in Windows Task Manager. If necessary, then stop these processes.
Open this folder on your computer:
C:\Program Files (x86)\Skype\Phone\
You should see there the Skype application file (Skype.exe). Right click on the Skype.exe file and select: Send to – Desktop (create shortcut). Right click on the newly created shortcut and select Properties and then the Shortcut tab. In the Target field you will see now:
"C:\Program Files (x86)\Skype\Phone\Skype.exe"
Click with your mouse on the text in the Target field and move your curser one space after the last quotation sign and add the text /legacylogin. The text in the Target field should now read:
"C:\Program Files (x86)\Skype\Phone\Skype.exe" /legacylogin
Click OK to save the changes. Start Skype using this new shortcut. Can you now login to Skype?

Blue screen with cursor at boot. And everything after that.

Dear Forums,
(Please note, I'll refer to the machine as a Server, but it is only using 10.4 client; I am merely using the Sharing capabilities of such).
I have a MDD G4 that I'm using as a server. When I start it up, I get the Blue Screen with Cursor (BSwC) at boot - and it never goes past that. (Can't move the cursor either).
I have read the articles
http://docs.info.apple.com/article.html?artnum=106464
And Dr. Smoke's
http://www.thexlab.com/faqs/startupitems.html
http://www.thexlab.com/faqs/repairprocess.html
I've also tried AppleJack and clearing out caches, zapping PRAM, etc. All the standard fare.
It will boot into safe mode just fine, and it is still acting as a server just fine.
I have also tried Multiple Users (to no avail).
I tried a reinstall of Tiger, which, interestingly enough, didn't give me the option for Archive and Install and Preserve, but instead only gave me the option to Upgrade (hm, from Tiger to Tiger). While this fixed nothing, the server continued to work after this.
Then I had the bright idea to install the OS to the 2nd drive I had within. 'Surely this would work,' I thought. But alas. It did not. In fact, clean installation, new disk, (and yes, I booted from this 2nd disk), the same BSwC problem.
So, please, Dear Apple Support Discussions, let there be someone out there smarter than I (I'm really not that smart, but I do follow instructions well).
-Ty

How long did you wait for the blue screen to go away? I also have a iMac G5 2GHz ALS.
My computer has been having a problem where on the first boot of the day, it it would hang in the gray screen for about 1.5 minutes and the blue screen for about 4 minutes. I thought it was permanently hung but discovered that it would eventually present the login screen. I could then login normally but none of my firewire external drives would mount. I could restart over and over and the same situation would be present.
Resetting the SMU seems to cure the problem and rebooting would be quick and all firewire drives mounted correctly. I could then reboot as many times after and normal behavior of the iMac would be repeatable.
However after having the system down for several hours and restarting it, the problem would be back.
I have now moved all my firewire drives to a powered hub and will watch over the next day or so to see if that changed anything.
Robert

Blue screen with rotating gear

I have installed a new hard drive in a mac mini PPC. When I try to install OS X from the original disk, I get as far as the language selection screen and then it goes to a blue screen with a rotating gear. I have left it there for an hour and nothing changes. I did make sure to format the drive before I tried to install. I don't know what to try but I am very stuck at this point.

Matthew:
Check your formatting against these directions:
Formatting, Partitioning Erasing a Hard Disk Drive
• With computer shut down insert install disk in optical drive.
• Hit Power button and immediately after chime hold down the "C" key.
• Select language
• Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• Select number of partition in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
Open installer and begin installation process.
cornelius

Can I use a blue screen with Final Cut Pro X?

Hi, I am at a school that uses Macbooks and has just purchased a blue screen (with lighting). I am new at chromakey / blue screening. I know that you can use iMovie for green screens, but could somebody please tell me what is a good software to use for a blue screen? Does Final Cut Pro X work with blue screens?
If anyone has any advice I would be very grateful!!
Thanks,
From Michelle.

The keyer effect in FCPX works very well with blue screen. Open effects browser and look for Keyer. When you add it to your blue screen clip it will automatically pick up the blue screen and key it out. You also have several controls to fine tune the edges etc.

What does it mean when you computer crashes and when you turn it back on it shows you a blank blue screen with a little folder and a question mark in the middle?

What does it mean when you computer crashes and when you turn it back on it shows you a blank blue screen with a little folder and a question mark in the middle? It's a old imac from 1997.

I don't have original discs that it came with.
Then you still can use the second option with the keyboard combo I posted, called "resetting the PRAM."
Also when you way hold the c key down do you mean turn computer off and turn back on holding the c key?
Yes, or you can simply restart. As you don't have the CDs, this isn't on the plate any more.
The internal backup battery is not expensive and, in most iMacs is user-replacable. If yours has a tray-loading optical drive like this one:
it takes a major teardown to replace the internal battery. If this is the case, you'd be better off to leave the computer plugged in all the time; that eliminates the main reason for having a working battery.
If it has a slot-loading optical drive like this one:
things are much easier. The battery is visible through the RAM access door on the bottom of the computer case. The manual:
http://manuals.info.apple.com/en_US/iMacG3_2000UserManual.PDF
has sketches of how to access the RAM and therefore the backup battery. Unfortunately, the pdf on the manual goes up sideways on-screen and the RAM instructions are pretty deep into the manual. It's probably easier to scroll (for a while) to the section on adding RAM and print the applicable pages.
When you work on the battery, some sort of non-conductive pliers or large tweezer or forceps help unless you have tiny fingers. Make sure to note the polarity of the old battery and install the new one in the same orientation.
The battery itself is readily available. If price is no oblect, you can get it for a small rasom from Radio Shack Store ("Tandy" outside the US) as part number 23-026.
Online, they are dirt-cheap even after adding shipping. I buy backup batteries form this outfit:
3.6v Newer Technology Lithium 1/2 AA PRAM Computer Clock Battery

Froze on Blue Screen with Apple and loading bar

My Ipod Touch was updated wtih new updates. It is now froze on a dark blue screen with an apple on it. Then a loading bar with nothing loading. I can't get it to turn off, or anything. Not sure what to do next.

Welcome to the discussions,
did you try to reset the ipod by holding the sleep and home button until the Apple logo comes up again? If this is not working, connect in recovery mode and restore.
Recovery mode: http://support.apple.com/kb/HT1808

Start Up problems, I'm past the grey screen now at blue screen with spinning gears.

Hello I'm working on my Mothers I Mac I believe its a G5,, I do see IMAC 8.1. Today when she turned it on all that came up is a gray screen with a spinning gear. I tried Disk Utility but the HD wasn't being recognized. After a few more trial and errors I finally reset the SMU, Which when I ran disk utility again the hard drive was recognized. I verified it and it said HD seems to be ok. I restarted and sure enough I made it past the gray screen but now Its stuck on a blue screen with a spinning gear. It looks almost like the login screen is trying to load but never comes up. Every 10-20 sec it flickers and the gear just keeps spinning. The fan was never coming on, not until I reset the SMU so I'm currently letting it cool down. Hoping this helps. Should I run the disk utility again and click the repair hd, even though no errors were listed when I verified it.

An iMac 8,1 is an Intel model. Are you sure it's a G5 (not an Intel model?)
Perhaps you should try reinstalling OS X:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Reset PMU and Powerbook won't boot past the blue screen with "Mac OSX" box

Hi-
Problem: I tried to reset my PMU, and now when my computer restarts it won't go past the blue screen with the "Mac OSX" logo in the box (and progress bar, that never fills up). I then also tried to reset PRAM, but it still won't boot properly.
Backstory--
I've had my 12-inch Powerbook G4 for about 3.5 years already, so things are starting to get a bit out of whack. I replaced my battery about 3 months ago, which has been great, but recently my power-cord has been wonky (having to unplug it and replug it in to make sure it actually charges the computer, the light flickers on and off, etc). Today it actually started producing SPARKS at the place where the thin white wire meets the white plastic power brick, so I decided it was time to get a new one. Brought it home, plugged it in, and since it seemed like the battery indication icon on the menu bar was all out of sync with the powercord colored-light, I tried restarting it a few times, but still the same. Then, I decided to reset the PMU, which may have been a huge mistake. And now it won't boot past the blue screen... Any advice? I'm going to try restarting it in "safe" mode, but I'd be so grateful for any recommendations. Hope I haven't done something irreversibly stupid with the PMU reset.
Thanks,
Samantha

Hello all,
Thanks for all of your great suggestions and info-- here are a few responses.
1) The disk I just borrowed from my friend appears to be the full retail version-- it looks just like the links that Ali B sent, and is in a large box saying "Mac OSX Tiger, version 10.4"... will this be the proper disk to do an Erase and Install? The only other disks I have came with my Powerbook when it was originally purchased, when it came Panther (I think, 10.3?). Would I use both sets of these disks to do erase and install? Or only the Tiger OSX disks?
2) I get the sense that Disk Warrior or Tech Tool might be necessary, but does it make sense to TRY to do erase-install before buying them? Also, are there any downloadable (for pay) versions of this, or would I need to track down the actual physical disks in Hong Kong or wait for them to be shipped?
3) I haven't yet tried the S.M.A.R.T. test, should I do that first? What is the procedure? Are there any results or ways to know if the drive is too far gone (so that I might instead replace the internal hard-drive) instead of pay 100 USD first to do the disk repair?
4) Cornelius said: "An alternative would be to completely reformat and erase the entire HDD, then re-install and restore your data from backup. If your backup is in the form of a bootable clone of the entire HDD, you can just clone it back." I use Super-Duper to back-up and the most recent one copied the whole thing-- what would be the later procedure of "cloning it back"?
5) As I'm able to use my computer pretty normally right now, but does it still mean that it might crash/die at any moment? Is there any way to tell?
Thanks so much!

HP 6525 Photosmart Blue screen with On/Off icon and "B8564450" message

Found my HP6525 in the following state:
- Blue screen, with an On/Off icon and various error messages
- Cannot turn printer off; press On/Off switch and HP logo appears and then an new or same Blue Screen appears with the same or different error message all starting with the letter "B"
- Removing power cord from printer, and reattaching results in same scenario
- cannot really turn printer OFF, just multiple instances of the Blue Screen on display
- Cannot do anything else since there are no other controls other than the touch-screen.
- Printer was set up for Wireless/Bluetooth operation with the two computers having wireless access being a
- Windows 7 Laptop
- Apple iPad
Both worked flawlessly before this???
What happened??
-Unfortunately, this is the FIRST occurrance of this level of issue with a long line of HP inkjets?????
How can I reload firmware?
- connecting via USB cable, and doing setup or something different?

Hello,
This seems like a hardware issue, I would suggest calling HP @8004746836 and see what options they have to replace or repair the printer.

Blank Blue Screen with diagonal lines

My new ACD 23 display is occassionally showing a blue screen with diagonal lines running through it. When I reboot, it comes up fine. I am using the monitor with a PC. It usually happens in the morning after it has been in sleep mode and I start the days work.
Any ideas as to what this could be?
Thanks,
J. Paul
Macbook Pro & Dell PC Windows XP

Only your OEM DVD has AHT, and not if you have installed a newer OS or reformatted.
Swap graphic card. You have a 3-4 yr old system.
Don't rely on fsck or Apple First Aid either.

Grey and Blue Screens with Spinning Pinwheel

Mid 2009 Macbook Pro 13 inch with Mac OSX Snow Leopard installed. 2.26 GHZ 4 GB 160 GB Version 10.6.3
I got this dead Macbppk Pro from my daughter . I put in a new battery and re-installed Mac OSX Snow Leopard from the licesned disc she bought so I could get rid of all her files and have free space and to make the Macbook now mine with my passwords etc. I got free support from Apple on how to install the disc and overwrite everything that was on it.
Until now ... I get a Grey Screen with the Spinning Pinwheel for endless time.
So the I tired the Hold Alt/ Option + Command + holding the P and R buttons while starting it up and got a Blue Screen with the spinning Pinwheel.
Any Help on what to try next ?
I only use it about once a month because I have a desktop. Does using it only once a month harm anything ? Should I be doing anything to not have this problem with it ?
Or do I have to re-install the disc again and if so .... what would be the procedure to do so ( I forget )
Thanks Eric

Hi Eric,
Thanks for visiting Apple Support Communities.
If your MacBook Pro is only starting up to a blue screen with spinning pinwheel, reinstalling OS X may be necessary. I would recommend going through all of these steps first:
Restart the computer in safe mode. If the computer successfully starts up in safe mode, choose Apple menu > Restart to see whether the computer will restart normally.
Starting up in safe mode
If you see the login window prompting you for a user name and password, but starting up doesn't progress, you may have incompatible login items.
Eliminating incompatible login items
Repair your startup disk or disk permissions by starting up from your Mac OS X installation disc and using Disk Utility.
Repairing a disk
Back up your disk and then reinstall Mac OS X by starting up your computer with your Mac OS X installation disc.
Reinstalling Mac OS X
From:
Mac OS X 10.6: If you see a blue screen at startup
Best Regards,
Jeremy

Blue screens with my new P45 Neo3-FR motherboard

Similar Messages

Maybe you are looking for