Blue Snowball USB microphone will not connect to audio hardware

My new Blue Snowball USB mic will not connect to the audio hardware in Premiere Pro. It connects well to my Mac but I cannot select it in Premiere Pro. Anyone know of a workaround or some help?

I was able to solve the problem by adding a Mono track first, then recording to that track. It's strange I have to do this, I have a Windows laptop at home that I use with CC 2014 and a Blue Yeti and Premiere just "knows" that I'm trying to record and makes the change.

Similar Messages

My usb modem will not connect to the internet after upgrading to OS X. The modem is active and was issued an IP addreess. There apparently is a connection error between the modem and Safari. Any ideas would be welcomed

MY USB modem will not connect to the Internet. The modem appears active on either USB ports and an IP address is assigned. The interface between the modem appears to be the problem. Any ideas?

mcaila wrote:
Update: I called my ISP (Verizon) and they were not much help.
What did have you do if anything?
I also tried to connect with an ethernet cord, and that too is not working.
What were the results from the Network Diagnostic test when connected by ethernet?
I've been searching online for hours and have found no solution that has worked.
What were those solutions that did not work other than what you already mentioned?

When i try to connect my iPhone 4S into iTunes through wifi or USB it will not connect the other thing is when i hook up my iPad into iTunes it will connect through wifi but not USB? Now is this a issue with my iPad and iPhone or is this iTunes?

When i bought my iPhone and my iPad they both were on iOS 7.0.2 i updated them shortly after thinking the new iOS 7.0.4 was better. i see its not but they both worked great with iTunes before and after the update. My question is why is my iPhone not connecting to iTunes? it will not connect through USB or wifi and i know that the setting to do that is turned on. my iPad connects through iTunes through wifi but not USB. This isnt making any sense but i wanna know is this a iTunes issue? or is it my phone and iPad??

This can sometimes be the result of a faulty/damaaged USB sync cable. Do you have another cable you could test it out with?
B-rock

Sierra Wireless USB card will not connect

I have purchased a Sierra Wireless USB card (AT&T USB Connect 881) to use with a iBook G4. The green power lites are solid green. However, I can not get a signal from AT&T. No one has been able to help solve this problem. I am ready to return it to AT&T for a refund.

Thx for ur reply. I just checked the model of the USB adapter is Belkin Basic N150.
The xp is able to see and identify the iphone wireless network and shows it in available networks with full signal strength. Once I click on connect then an alert message says that it is detecting network type pls wait. Then another message appears stating that "selected network may be no longer in range. Pls refresh the list and connect again"
As suggested by you I will try it on windows 7.

USB port on my iTouch will not connect to anything

My USB port will not connect to any jack I have. If there is a cheap and or easy way to repair that will be great.

This is exactly what's happening to me. It says that it is connected but when I try to connect to like safari or iTunes, stuff like that, it doesn't work!!!!!!!

Blue Yeti USB microphone not working in ALSA/PulseAudio

Hi all,
I recently bought a Blue Yeti USB microphone. It is supposed to require no drivers for Windows and OS X, and so far, it works well under Windows, but I cannot seem to get it to function on Arch Linux. As fair warning, although I am relatively experienced with Linux, I don't know much about the internals of ALSA/PA --- up until now, it has just "always worked", so this is my first real foray into the area. I've tried for many days, with no success, to get this thing working.
So, let's start off first with my configuration.
I have a few audio devices:
An on-board audio solution that I don't typically use. For testing, I have connected an old, crappy pair of headphones, but normally I keep this disabled. It has one capture device. (Analog stereo [or 5.1/7.1/etc] duplex)
An external DAC that is connected via USB and is output-only. So, no capture devices on that. (Digital/IEC958 output)
The Blue Yeti itself, which is connected via USB and supports output (it has an internal DAC) as well as input. So, one capture device here. (Digital stereo output and analog stereo input???)
The HDMI-out stuff for nvidia, which I never use
Here is the output of "arecord -l":
**** List of CAPTURE Hardware Devices ****
card 1: Microphone [Yeti Stereo Microphone], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 2: ALC892 Alt Analog [ALC892 Alt Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
Here is the the output of "arecord -L":
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=Microphone
Yeti Stereo Microphone, USB Audio
Default Audio Device
front:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
Front speakers
surround40:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
4.0 Surround output to Front and Rear speakers
surround41:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
IEC958 (S/PDIF) Digital Audio Output
sysdefault:CARD=PCH
HDA Intel PCH, ALC892 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
Front speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
Here is the output of "aplay -l" (for completeness):
**** List of PLAYBACK Hardware Devices ****
card 0: Audio [USB2.0 High-Speed True HD Audio], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 1: Microphone [Yeti Stereo Microphone], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
If the output of "aplay -L" is needed, let me know, but it's not all that different from arecord -L.
Here is my /etc/asound.conf:
defaults.pcm.rate_converter "samplerate_best"
pcm.!default {
type pulse
fallback "sysdefault"
hint {
show on
description "Default ALSA Output (currently PulseAudio Sound Server)"
ctl.!default {
type pulse
fallback "sysdefault"
# vim:set ft=alsaconf:
I don't remember where the bulk of that came from; maybe it was installed like that or maybe I put it in there. Here is another useful command showing non-commented-out/non-blank lines in the pulseaudio conf:
$ egrep -v '^;|^#|^$' /etc/pulse/*.conf
/etc/pulse/client.conf:autospawn=no
/etc/pulse/daemon.conf:exit-idle-time=0
/etc/pulse/daemon.conf:default-sample-rate = 192000
So, there's not much I've done there. Here's the contents of /proc/asound/cards:
0 [Audio ]: USB-Audio - USB2.0 High-Speed True HD Audio
CMEDIA USB2.0 High-Speed True HD Audio at usb-0000:00:1d.0-1.7, high speed
1 [Microphone ]: USB-Audio - Yeti Stereo Microphone
Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed
2 [PCH ]: HDA-Intel - HDA Intel PCH
HDA Intel PCH at 0xf7530000 irq 52
3 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xf7080000 irq 17
And here's the contents of /proc/asound/modules:
0 snd_usb_audio
1 snd_usb_audio
2 snd_hda_intel
3 snd_hda_intel
Now, here is the output of "pactl list sources" (the Blue Yeti is last in the list):
Source #3
State: RUNNING
Name: alsa_input.pci-0000_00_1b.0.analog-stereo
Description: Built-in Audio Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 7
Mute: yes
Volume: front-left: 17972 / 27% / -33.71 dB, front-right: 17972 / 27% / -33.71 dB
balance 0.00
Base Volume: 6554 / 10% / -60.00 dB
Monitor of Sink: n/a
Latency: 610 usec, configured 100000 usec
Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY
Properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "ALC892 Analog"
alsa.id = "ALC892 Analog"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "2"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xf7530000 irq 52"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1b.0"
sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card2"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "1e20"
device.product.name = "7 Series/C210 Series Chipset Family High Definition Audio Controller"
device.form_factor = "internal"
device.string = "front:2"
device.buffering.buffer_size = "76800"
device.buffering.fragment_size = "19200"
device.access_mode = "mmap"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "Built-in Audio Analog Stereo"
alsa.mixer_name = "Realtek ALC892"
alsa.components = "HDA:10ec0892,10438436,00100302"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
Ports:
analog-input-front-mic: Front Microphone (priority: 8500, not available)
analog-input-rear-mic: Rear Microphone (priority: 8200, available)
analog-input-linein: Line In (priority: 8100, not available)
Active Port: analog-input-rear-mic
Formats:
pcm
Source #11
State: RUNNING
Name: alsa_output.pci-0000_00_1b.0.analog-stereo.monitor
Description: Monitor of Built-in Audio Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 7
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.pci-0000_00_1b.0.analog-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of Built-in Audio Analog Stereo"
device.class = "monitor"
alsa.card = "2"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xf7530000 irq 52"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1b.0"
sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card2"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "1e20"
device.product.name = "7 Series/C210 Series Chipset Family High Definition Audio Controller"
device.form_factor = "internal"
device.string = "2"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
Formats:
pcm
Source #15
State: RUNNING
Name: alsa_output.usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio.iec958-stereo.monitor
Description: Monitor of USB2.0 High-Speed True HD Audio Digital Stereo (IEC958)
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 8
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio.iec958-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of USB2.0 High-Speed True HD Audio Digital Stereo (IEC958)"
device.class = "monitor"
alsa.card = "0"
alsa.card_name = "USB2.0 High-Speed True HD Audio"
alsa.long_card_name = "CMEDIA USB2.0 High-Speed True HD Audio at usb-0000:00:1d.0-1.7, high speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.7:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.7/6-1.7:1.0/sound/card0"
udev.id = "usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio"
device.bus = "usb"
device.vendor.id = "0d8c"
device.vendor.name = "C-Media Electronics, Inc."
device.product.id = "0319"
device.product.name = "USB2.0 High-Speed True HD Audio"
device.serial = "CMEDIA_USB2.0_High-Speed_True_HD_Audio"
device.string = "0"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-usb"
Formats:
pcm
Source #19
State: RUNNING
Name: alsa_output.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.iec958-stereo.monitor
Description: Monitor of Integrated Rate Matching Hub Digital Stereo (IEC958)
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 48000Hz
Channel Map: front-left,front-right
Owner Module: 9
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.iec958-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of Integrated Rate Matching Hub Digital Stereo (IEC958)"
device.class = "monitor"
alsa.card = "1"
alsa.card_name = "Yeti Stereo Microphone"
alsa.long_card_name = "Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.8:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.8/6-1.8:1.0/sound/card1"
udev.id = "usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone"
device.bus = "usb"
device.vendor.id = "b58e"
device.vendor.name = "Intel Corp."
device.product.id = "9e84"
device.product.name = "Integrated Rate Matching Hub"
device.serial = "Blue_Microphones_Yeti_Stereo_Microphone_REV8"
device.form_factor = "microphone"
device.string = "1"
module-udev-detect.discovered = "1"
device.icon_name = "audio-input-microphone-usb"
Formats:
pcm
Source #23
State: RUNNING
Name: alsa_input.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.analog-stereo
Description: Integrated Rate Matching Hub Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 48000Hz
Channel Map: front-left,front-right
Owner Module: 9
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 17775 / 27% / -34.00 dB
Monitor of Sink: n/a
Latency: 949811526 usec, configured 100000 usec
Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY
Properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "USB Audio"
alsa.id = "USB Audio"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "1"
alsa.card_name = "Yeti Stereo Microphone"
alsa.long_card_name = "Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.8:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.8/6-1.8:1.0/sound/card1"
udev.id = "usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone"
device.bus = "usb"
device.vendor.id = "b58e"
device.vendor.name = "Intel Corp."
device.product.id = "9e84"
device.product.name = "Integrated Rate Matching Hub"
device.serial = "Blue_Microphones_Yeti_Stereo_Microphone_REV8"
device.form_factor = "microphone"
device.string = "front:1"
device.buffering.buffer_size = "19200"
device.buffering.fragment_size = "4800"
device.access_mode = "mmap"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "Integrated Rate Matching Hub Analog Stereo"
alsa.mixer_name = "USB Mixer"
alsa.components = "USBb58e:9e84"
module-udev-detect.discovered = "1"
device.icon_name = "audio-input-microphone-usb"
Ports:
analog-input-mic: Microphone (priority: 8700)
Active Port: analog-input-mic
Formats:
pcm
Honestly, I think that's about all of the configuration info I can give. Here are some screenshots of pavucontrol, though, in case you are not yet sated: http://imgur.com/a/ngyLl
Now, on to the debugging stuff. First: everything except Blue Yeti recording works. The external DAC works, the on-board audio (both input and output) work, using the DAC in the Blue Yeti to play music/monitor the microphone works (so it works as an output). The only thing that doesn't work is actual recording from the Blue Yeti itself.
When I try to record from the Blue Yeti with parecord -v, I get very strange behavior. Essentially, the "latency" of the microphone measured is exactly the same as the time it has been recording. That is, if it has been recording for 5 sec, then the latency is 5000000 usec. Also, if I try to record something in Audacity, I get no result except for a message box that says "Latency Correction has caused the recorded audio to be hidden before zero. Audacity has brought it back to start at zero." Also, pavucontrol doesn't show an input volume bar for the Blue Yeti, as in the above screenshots, whereas it normally will for microphones that are getting input. The Yeti is not muted, either, so it should be picking up ambient fan noise and such.
Does anyone have any ideas? Is there some configuration error I've made? Typically, this sort of stuff simply works out of the box for me, so I am somewhat stuck on what to do. Could it be a driver-level bug?

I'm not sure what you mean by "mixed with audio in Alsamixer". Can you clarify?
With that said, my problem did mysteriously fix itself after some update (presumably to alsa). Unfortunately, I noticed it in passing one day while I was changing the volume of something in pavucontrol, so I don't remember the exact update that caused it to work. But yes, my current setup does work now: I can listen to audio through my DAC and use the Yeti for recording. However, I have found that use of the Yeti crashes Google Hangouts, although it works perfectly in every other program I've tried.
As documentation, here is my current working setup (it is very similar to the above): in PulseAudio, the DAC is set to be a Digital Stereo (IEC958) output. The Yeti (called an 'Integrated Rate Matching Hub' in pavucontrol) is set to be an Analog Stereo Input. In the input devices section, I have the Yeti's volume set to around 58% (-14.31 dB), which is past the base volume a fair ways but produces decent levels for recording. The DAC's volume is set to 100% (0dB gain, the DAC takes care of the level). In alsamixer, I have the mic level for the Yeti set to 40.
Edit: This is a long-time-later edit, but let me say that when you have multiple USB audio devices, what USB hub and in what order they are connected seems to matter a great deal. If you can't get your Blue Yeti to work, try moving it to a different set of USB ports (controlled by a different controller) on your motherboard. This magically fixes the issue for me.
Last edited by rwiggins (2014-12-14 00:26:39)

I have three Blue Yeti USB Microphones, and when I try to create an aggregate device in Audio MIDI on my MBP it lets me select two microphones but not the third. I need all three for a podcast, any solutions?

I have three Blue Yeti USB Microphones, and when I try to create an aggregate device in Audio MIDI on my MBP it lets me select two microphones but not the third. At first I thought maybe the third microphone was just defected or something but I tested the mic individually and it works fine. It'll let me use two Blue Yeti's and another microphone but not three Yeti's at once.

David Boroditsky wrote:
The problem is that the mac chokes on having 2 identical mics attached at the same time.
Ive had 2 identical USB AT2020 mics connected at the same time on both macbook pro and macbook Air.
The "Yeti" mics, are, lets say undesirable, and low to mid computer consumer mics.

My ipod touch has a usb cable picture with an arrow pointingto the itunes logo. the ipod will not connect to a computer and is unable to be turned off as there is no red power slider when the powerbutton is pressed. what can i do to fix this?

my ipod touch has a usb cable picture with an arrow pointing to the itunes logo. the ipod will not connect to a computer and is unable to be turned off as there is no red power slider when the power button is pressed. what can i do to fix this?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

TS3274 How can I connect tv to ipad? Want it to use netflex but will not connect using USB cable.

How can I connect tv to ipad? Want it to use netflex but will not connect using USB cable.

http://store.apple.com/us/browse/home/shop_ipad/ipad_accessories/cables_docks
You should find a solution here

My iPod 4th-gen charges just fine in any wall outlet, but when connected to my brand new ASUS Windows-8 laptop's USB 3.0 port the charging process just keeps "blinking" on both the iPod and the laptop and will not connect to Itunes...

Hi, I HATE to ask for help with this, but I HAVE looked everywhere and Google searched different wordings and have not found anything similar nor a solution to my problem! My good old iPod 4th-gen charges just fine in any wall outlet, in any house, but when I connect it to my brand new ASUS laptop that has Windows-8 and 3.0 USB ports using the charging/data cable, the charging process just keeps "blinking" BOTH the iPod and the laptop and it will not connect to ITunes and I get "A Device is Detected" message that keeps popping up and going away over and over right above the Windows desktop toolbar. When I go to control panel and select "Devices" it does show the iPod, but for only a split second and than it disappears, but than it comes back again for a split second and than it disappears again and just keeps doing that over and over and over! I have tried resetting the iPod while it is plugged into the laptop by holding the power and menu buttons, that did no good. I also tried uninstalling iTunes and any other Apple stuff listed and reinstalling it all, that did NOT work! The iPod, the laptop and iTunes ARE all fully updated! I AM using a brand new charging/data cable that I just opened up an hour ago (I've learned to keep a few brand new ones around at all times since these piece of garbage rip-off cables hardly last a week, even when you baby them!). I also tried a few old cables, they all do the same thing! I would like to get this piece of junk to connect to my new laptop, even if only once, so that I can change/delete some songs and transfer a few dozen photos,since I haven't been able to do any of that stuff since my old laptop (that NEVER had any problems connecting) died way back in May! lol. I hope somebody knows a fix or solution! Thank You!

Try on another computer to help determine if iPod or computer problem.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

My 3rd generation ipod touch will not connect to itunes. i plug it up to the computer by USB and it makes a jingle and my computer recognizes it in the my computer screen, but it will not connect to itunes. what should i do?

my 3rd generation will not connect to itunes when i plug it up to the computer by USB. i have tried to do it with itunes open and closed. it wont recognize it but it is recognizes in the my computer screen. it even makes a jingle when plugged up. on my ipod i can download music wirelessly from my itunes. other than this issue my ipod works just fine. what should i do?

Try
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
Before you reinstall the Apple software, also remove iCloud vi Control Panel Remove programs. The reinstall the Apple programs
New cable and different USB port?
Runs this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Try on another computer to help determine if computer or iPod problem

My iPod will not connect to the iMac via USB.

I can no longer charge nor sync my ipod because it will not connect via USB. What can I do to fix this?

What have you tried so far in terms of troubleshooting this issue? Are you plugging the iPod into a high powered USB 2.0 port on the back of your PC? Have you tried a different USB cable?
What happens if you try to reset the device with it still connected to the PC?
How to reset iPod
Has this iPod ever worked on this PC or is this the first time you have time you have tried connecting it?
Have you carefully worked through each and every single suggestion in this Apple support document?
iPod not recognized in 'My Computer' and in iTunes for Windows
B-rock

HP Officejet Pro 8500A 910A, Vista 32-bit, will not connect via usb to my PC!!!

I used to have this all in one connected to my pc, until I was experiencing a few printing issues, so I decided to uninstall it! When I tried to reinstall it, the pc will not connect it. I have tried different ports and have replaced the cable, also downloaded the latest software and drivers all to no avail. I can connect wirelessly to my laptop, but unfortunately this isn't a solution for my desktop as it's not wireless, therefore it has to be connected via usb. At my wits end, please help me!!!!!
This question was solved.
View Solution.

Hello,
Can you try inserting a flash drive into one of the USB ports in the printer, to make sure it reads it?
The port on the printer might be what's giving you the issue. Also, can you try connecting the printer USB to a different PC?
Let me know the outcome.

HT201210 ipod touch frozen on connect usb and will not sync

my ipod touch has frozen on connect usb and will not sync

Hi kittens53,
Thanks for visiting Apple Support Communities.
You can use these articles to troubleshoot the connection between iTunes and your iPod:
iPod not recognized in 'My Computer' and in iTunes for Windows
http://support.apple.com/kb/TS1369
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Regards,
Jeremy

HT5299 I have a Gdrive mini and 2 LaCie hard drives that connect fine using USB. Thunderbolt to fire wire 800 adaptor will not connect to either my MAC air or LaCie drives. Help

I have a G drive mini and 2 LaCie hard drives that connect fine using USB. Thunderbolt to fire wire 800 adaptor will not connect to either my iMAC or Mac air or LaCie drives. Help

Have you tried any of these soundcards designed for 2.0?
The 3.0 port is categorically designed to be comoatible with all 2.0 devices. The port itself will adapt to the usage parameters of the device.
But if you really want to downgrade, then simply plug any 2.0 hub into a MBA 3.0 port. The ports on the hub will be 2.0.

Blue Snowball USB microphone will not connect to audio hardware

Similar Messages

Maybe you are looking for