Blue tint after login and/or leaving the screensaver

Allot of the time when I leave the screensaver or login my screen decides chuck in an aqua blue tint.
Any ideas how to go about fixing this?
Thanks very much in advance!

HiJim,
Did you ever figure this out? WHat was causing the purple blue tint after waking?
I have my iMac G5 with X.4.11 set to wake up in the morning, but when I get to my desk I see the purple light blue screen. Upon moving the mouse I can see the screensaver is working “underneath.”
Sure would love to fix this.
Anybody able to help?
Thanks, and so long for now, TOM

Similar Messages

Blue screen after login and HD and startup disk is full -how to erase data?

Blue screen after login and Hard drive and startup disk is full -How do I get in to erase data?

this user tip might help:
Your Mac needs adequate hard drive space to operate normally. How full can a drive be before it's too full? There is no hard and fast rule that says “X” amount or “%” of free drive space is needed. A low amount of RAM requires more drive space for Virtual Memory’s swap files.
Problems from insufficient RAM and free hard disk space are discussed in this link
http://www.thexlab.com/faqs/lackofram.html
Here’s some general guidelines for minimum hard drive free space:
1. As a general rule, your available space should be 5GB as an absolute minimum as it generally requires that much free space to perform an Archive and Install of Mac OS X and still preserve some free space for VM swap files.
2. Some say that your hard drive should have at least 5% of it's capacity available for use. Still others say 10% to 15%. If you routinely process complex graphics and videos, even more space is required.
Look at these links about freeing up more space.
Where did my disk space go?
_*http://www.macfixitforums.com/showflat.php?Cat=&Board=Forum38&Number=770243*_
Download & use WhatSize described in this link or Disk Inventory X @ _*http://www.derlien.com/*_
Freeing space on your Mac OS X startup disk
_*http://www.thexlab.com/faqs/freeingspace.html*_
Amazing Disappearing Drive Space
_*http://www.pinkmutant.com/articles/TigerMisc.html*_
Increase HD Free Space
_*http://macosx.com/forums/howto-faqs/275191-how-easily-increase-hd-free-space-lap top.html*_
How to free up my disk space
http://www.macmaps.com/diskfull.html
JGG

I am trying to run page 192.168.0.170 for my IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

I am trying to run page 192.168.0.170 for viewing IP Cameras but after login and password the page is not responding. Plz help!

After installing new OS i can't type a login and password because the font is not supported. DO NOT KNOW WHAT TO DO!!!!HELP PLS?!

after installing new OS i can't type a login and password because the font is not supported. DO NOT KNOW WHAT TO DO!!!!HELP PLS?!

Hello Pete from another old guy,
It sounds like you have an older iMac than the 2006 and newer model this forum covers. The problem is that, in 2006, Apple changed from PowerPC to Intel processors and third-party developers soon stopped making new software for the older processors. That's why you cannot upgrade Flash player--the current version requires a Mac the "2006 and later" processor.
However, not having a current version of FlashPlayer should not affect your ability to download. If you try downloading, do you get an error message or does something else happen?
Do you have another web browser like FireFox or Camino on your computer?
but would love to get my MAC back up to date and running right.
Well, "running right" may be doable but "up to date" may not be. You are already at as high a Mac OS level that a pre-2006 Mac can use. We need to pin down your variant to make recommendations. From your Apple menu at the left end of the menu bar, do "About this Mac":
That brings up this window:
Let us know what yours say for "processor." The two choices are "PowerPC" as in the example, or "Intel." If you have an Intel processor, you have more options available.
Awaiting your report,
Allan

Menu tabs disappear completely after login and appears if only i press on item node at hire level

I'm using a Menu Model to Create a Page Hierarchy in my adf application on Jdeveloper 11.1.2.3.0
it is in three levels level 1 have 2 item nods (home - Help) displayed as buttons
                            level 2   contains 5 item nods about the managements displayed as tabs
                            level 3   is about reports displayed as list
the point I have apply security in the application using Adf security wizard and i assign roles and users and grants
all works fine but level 2 tabs disappear completely after login and appears if only i press on Home item node at run time
I create 2 users (admin) has all roles and can view all tabs in level 2 of my navigation and another user (emp) which can view one Tab page in level 2
Point 1 --the item nod are rendered according the #{securityContext.regionViewable['oracle.view.pageDefs.RentManagPageDef']}     (EL ) expression language
and other item nod render property are set as the same but in the page name definition
it works fine
_ Point 2 in my page template I set #{menuInfo.rendered} for renderd property of the command navigation item
it works fine
- point 3 I add a go link in my template to explicit perform log in log out from the app and redirect the user to the required page
Destination is
#{securityContext.authenticated ? "/adfAuthentication?logout=true&end_url=/faces/wearhouse.jsf" : "/adfAuthentication?success_url=/faces/company.jsf"}
and its also works fine
the problem is in the level 2 navigation tabs which is diaper after explicit log in the app directs the user to the correct page successfully
But the tabs are not rendered till I press on home button on Level 1 navigation it appears and it appears correctly cording the logged in user validation
in another words i log in as user (admin) i get directed to the successful log in page in the link go but level 2 tabs are invisible or not rendered at all    I click on Home button in level1 navigation the tabs
become rendered or viewable and i navigate normally
I log out as admin the level 2 tabs becomes invisible again
then I log in as (emp) i get directed to the successful log in page and level 2 tabs are still invisible or not rendered
I click on Home button in level1 navigation the only one tab the user emp authorized to it gets rendered (appears)
and its semi correct behavior because this is what I want him to see only
my tries to find solution
I tride to use
#{securityContext.userInRole['division']}
on the menu node item   I found same behavior level 2 tabs gets hidden till i click on home link at run time
I tride to use #{securityContext.authenticated} to control item nods rending
all tabs remains visible and i dont want that ain adition if user clicks on a tab of page he has no authority on it i recive server error
I read 30.7 Creating a Login Page in the Fusion Developer's Guide for Oracle Application Development Framework to finde about redirecting user
and it is using the same as i did from adf tutorials
I tried to make new navigation app on fast
maybe i made incorrect change in any stage of my original app
but I found same behavior
I tried to set disabled property instead of rendered property the tabs are always rendered   but I got server error when I click on a tab which a user does not authorized
So I doubt maybe problem in the El or the way I use to control rendering item node
or there additional step to stop all the tabs disappear after login
I hope please some one Help or tell me what i have to read about in the developer guide or interface developer guide or article on the web
I'll be gratfule
I know maybe it is small issue but help me please

Hi,
have a look at the sample that comes with this article: Oracle ADF: Security for Everyone It uses resource remissions to authorize panel tabs.
One test to run is to print the outcome of the security evaluation (e.g. output text) to see what it returns.
Frank

Ios7 bookamrking web application to home screen via Safari crashes after login and when we try to open any link inside. Can anyone please tell me if there is any scheduled fix for this bug in safari?

ios7 bookmarking web application to home screen via Safari, crashes after login and when we try to open any link inside from the icon that gets created on the home screen. Can anyone please tell me if there is any scheduled fix for this bug in safari?
From what i understand i see that - Cookies are not transferred between your website and your webapp when installing the icon on the home screen (for authentication purposes for example). It was working until 6.1 and now it’s not working anymore.
Can someone please tell me if this bug will be fixed in any future release, if so the ticket number of some kind that i can track, or if there is a workaround for this issue?

ios7 bookmarking web application to home screen via Safari, crashes after login and when we try to open any link inside from the icon that gets created on the home screen. Can anyone please tell me if there is any scheduled fix for this bug in safari?
From what i understand i see that - Cookies are not transferred between your website and your webapp when installing the icon on the home screen (for authentication purposes for example). It was working until 6.1 and now it’s not working anymore.
Can someone please tell me if this bug will be fixed in any future release, if so the ticket number of some kind that i can track, or if there is a workaround for this issue?

How can I take off the text on the bookmark bar and just leave the Icons of the bookmarks on the boomark bar ?

I'd like to save space for more sites on my bookmark bar so I'd like to take off the text on the bookmark bar and just leave the site Icon's...that way there will be much more space to add on more sites to my bookmark bar.

SImple open the bookmark properties and erase the name, to open the bookmark properties:
*Go to '''Bookmarks''' >> '''Show all bookmarks''' >> or press '''Ctrl+Shift+B ''' click on the bookmark to see the properties.
*Go to bookmark page click on the blue star to see the properties or Press Ctrl+D

I tried updating to iOS 8.1 but it have the apple symbol and a blue screen pops up and it restarts the process and its been going on about 3 weeks already. I dont know what to do? Is my iPad broke cause I just got that iPad in August.

I tried updating to iOS 8.1 but it have the apple symbol and a blue screen pops up and it restarts the process and its been going on about 3 weeks already. I dont know what to do? Is my iPad broke cause I just got that iPad in August.

Hi You may have a hardware fault take ipad to Apple Store. Ring then first to make an Appointment take box and you purchase paperwork they may give you A replacement. Before you do that Try a Reboot hold down power button & menu button hold both down until you see Apple Logo you may need to hold down for up to 30 Seconds But you may need to do this more than once. If it doesn't work take back to Apple Store. Cheers Brian

HT5621 I have 14 cent on my apple account and cannot leave the Irish apple store for the Canadian store,how do I use this 14 cent or delete it from my account?

I have 14 cent on my apple account and cannot leave the Irish apple store for the Canadian store,how do I use this 14 cent or delete it from my account?

Greg the king hyland wrote:
... ,how do I use this 14 cent or delete it from my account?
Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

I am having problem downloading application on Mac app store, when I try to login and start downloading the application, it will say "Your device cannot be verified"

I am having problem downloading application on Mac app store, when I try to login and start downloading the application, it will say "Your device cannot be verified"

Back up all data before proceeding.
Step 1
Triple-click anywhere in the line below on this page to select it:
/Library/Preferences/SystemConfiguration/NetworkInterfaces.plist
Right-click or control-click the line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and test.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
Log out, log back in, and test. If there's no improvement, continue.
Step 2
Reset your computer’s PRAM.

Why doesnt the DVD version of iworks work, after uploading (and then deleting) the trial version?

why doesnt the DVD version of iworks work, after uploading (and then deleting) the trial version?

Check out this discussion in the iWork forum. Yvan's AppleScript (about 6 messages down) will solve your problem.

I've downloaded adobe after effects and now at the end of downloading it appears "errot extracting t

I've downloaded adobe after effects and now at the end of downloading it appears "errot extracting the product installer (error 101). check for availbale disc space on your computer and try downloading the product again. I have 193 GB of free space in my system. ????

We cannot know. You are not telling us anything about your system. This error usually occurs due to running out of temporary disk space in the relevant folders. Check this:
Installation Preparations
Important Directories
Other than that, refer to this:
Troubleshoot Adobe Download Assistant
In short: Do a little housekeeping, download again.
Mylenium

LCD goes blue/black after login; fine in Safe Mode

My mom's mac mini is experiencing a very frustrating problem.
She has an Acer 19 inch LCD. After startup she'll start up Safari or iChat or Mail, etc. and her display will go all blue and then just go black. Sometimes it will flicker back to usable and then go back to blue/black after a few more seconds.
We've been troubleshooting for a few days now and have discovered the following:
- When logging in under Safe Mode, the monitor works just fine.
- Removing all Login Items from her account doesn't help.
- Resetting the PRAM and trashing the plist file doesn't seem to help at all.
- Creating a new user account and logging in under that new test account doesn't help either.
So the bottom line is that Safe Mode works, but Normal mode does not.
Any help/ideas on what to try next?

OK, that helps. So this is a wide Acer 19-inch? 1440 x 900 native? Interesting that in Safe mode it defaults to 1360 x 768.
What I would tell her to try is the following: Boot Safe and then go into Displays preferences and switch the resolution to 1024 x 768. Refresh should be 60Hz. Then restart normally. Often, when you switch resolutions in this way while in Safe mode, during a normal restart, that last selected resolution will persist allowing the screen to come up in 1024 x 768 booted normally. Then, have her go into Display preferences again and see if 1440 x 900 at 60Hz is a selectable option (I assume that is native). If it is, select it. Hopefully things will return to the way they were back when the monitor worked fine.
Since you are remote, it might be worthwhile for you to spend a little time and learn how to screen share remotely over iChat. It's pretty easy to do if you are both running Leopard and it will allow you to control her computer remotely so you can administer to it those times when she needs help. Good luck.

Satellite L500 - blank blue screen after login to Win 7

Hi
I have this laptop and i can start up the laptop and it loads fine to the login page i then can login but when the screens opens after login it appears as a blank blue screen with the document folder open i have no background picture and no startup menu nothing else except the document folder.
From there i can access my files etc and anything else internet etc everything but i dont know how to get the screen back to normal.
If i go on background display i can see the image that should be on the background and change it but nothing happens on the full screen.
I have no restore point as yet as new laptop for xmas, i do have backup discs but think its just something to do with the display.
If go into files and folders it shows me the icons on the desktop but all i see is this blank screen.
Any ideas please, if not would restore files work or full back up disc
Thanks very much for any help

Hi
Check this:
Click right on the desktop and choose Personalize.
There you should check the area: Basis design and design with high contrast
Choose Windows 7 basic.
Then reboot the unit.
Usually this should help to get the Windows 7 common design and desktop settings.
But if this will not help then you could use an fast solution which would be a usage of the recovery disk of HDD recovery option.
This would format the HDD and would reinstall everything again

Can't see desktop with blue screen after login

Hi
we have a server 2008 ent SP2 that sometimes when use remote desktop or via vmware console to access this server, after login we got blue screen and can't see desktop. after force reboot it recovery.
From application log, we find some error:
Description (Event ID: 1000):
Faulting application Explorer.EXE, version 6.0.6002.18005, time stamp 0x49e01da5, faulting module msshsq.dll, version 7.0.6002.18255, time stamp 0x4be071d5, exception code 0xc0000005, fault offset
0x000063fd, process id 0x1300, application start time 0x01cf9a43236d46dd.
Description(Event ID: 9009):
The Desktop Window Manager has exited with code (0x40010004)
Description(Event ID: 1530):
Windows detected your registry file is still in use by other applications or services. The file will be unloaded now. The applications or services that hold your registry file may not function properly afterwards.
DETAIL -
1 user registry handles leaked from \Registry\User\S-1-5-21-249263827-1212357926-315576832-391740:
Process 3812 (\Device\HarddiskVolume1\Windows\System32\winlogon.exe) has opened key \REGISTRY\USER\S-1-5-21-249263827-1212357926-315576832-391740

Hi,
In general, event ID 1530 means there are some data in the user profile are still be accessed when the user log
off from the Terminal Server. Please check if any of the data is still remained in the user profile supposed to be deleted. You can use Process Monitor or Process Explorer in order to find the software which is using the data and find the solution. If there
is no such data remained, the Windows have possibly stopped the process and deleted the data when log off. In such a case, you can ignore the Event 1530.
In addition, I recommend running SFC /Scannow from an elevated command prompt and check a dump file for Windows
Explorer under C:\Localdumps.
Besides, you can also download
Autoruns to troubleshooting Explorer issues. Please run Autoruns as Administrator, go to Options menu, Filter, select Hide Microsoft Entries and Ok. After that, open the Explorer tab,
and you will see all DLL that are running inside File Explorer, so start disabling and testing if Explorer crashed.
Furthermore, the KB below may be helpful:
http://support.microsoft.com/kb/961038/en-us
Best regards,
Susie

Blue tint after login and/or leaving the screensaver

Similar Messages

Maybe you are looking for