Blue Yeti USB mic is SUPER loud!

Just bought this so hoping it's operator error, but even with mic gain turned all the way down, it pegs in the red. Played with Audio Preference settings to no avail. Any suggestions or is this mic too hot for GBand?

For those on a Mac that are still having this problem (me), open Audio Midi Setup from your Utilities folder and check the settings for your Yeti in there.
I found that mine was automatically turned up by 20db which is what was giving me such awful distortion. Bringing it down to about 6db on each side seemed to be the magic number, and I can of course use the knob on the mic to fine tune that.

Similar Messages

Blue Yeti USB Mic not audible

Hi Everyone,
I plugged my new USB microphone into my MAC and recorded a track of vocals which worked fine.
But when I went to record a second track of vocals, the sound is not recording?
I can hear the sound through the headphones, but the sound is not recording to the track or garage band.
Any help much appreciated.
Thanks.

Hi Gary,
I am embarrassed to say that I have been doing this support stuff for quite a while and have never opened up that utility. I don't support Midi Devices, so when I saw Midi in the name, I just bypassed it.
But you were correct, that fixed the issue. In the utility, the output tab was set to 44.1K instead of 48K, changed that to 48K and it worked perfectly, QT now captures at 48K and sounds good. I have not tested it in FCP 5.1 yet, but I assume that FCP will also capture at 48K, now that the Mic is set correctly.
Follow up question 1, the "M" slider (I am assuming that is the "Master" Slider you were referring to in your post) is not selectable on either the Input or Output side, it is grayed out, is there a way to enable that slider?
Follow up question 2, the Input side is set to Value = 0.53 and dB = 24.00 and the Output side is set to Value = 0.27 and dB = -18.00. With those settings, the test VO's I have run sound pretty good, but should I make any changes to the default Values list above (like make the input and Output side match) or should they be left at the default values?
I really appreciate your input and was hoping to find a way to set the properties of the Mic, but I didn't know that the "Audio Midi Setup" was the place to do that.
Thanks a lot!
Kalagan

Blue Yeti USB microphone not working in ALSA/PulseAudio

Hi all,
I recently bought a Blue Yeti USB microphone. It is supposed to require no drivers for Windows and OS X, and so far, it works well under Windows, but I cannot seem to get it to function on Arch Linux. As fair warning, although I am relatively experienced with Linux, I don't know much about the internals of ALSA/PA --- up until now, it has just "always worked", so this is my first real foray into the area. I've tried for many days, with no success, to get this thing working.
So, let's start off first with my configuration.
I have a few audio devices:
An on-board audio solution that I don't typically use. For testing, I have connected an old, crappy pair of headphones, but normally I keep this disabled. It has one capture device. (Analog stereo [or 5.1/7.1/etc] duplex)
An external DAC that is connected via USB and is output-only. So, no capture devices on that. (Digital/IEC958 output)
The Blue Yeti itself, which is connected via USB and supports output (it has an internal DAC) as well as input. So, one capture device here. (Digital stereo output and analog stereo input???)
The HDMI-out stuff for nvidia, which I never use
Here is the output of "arecord -l":
**** List of CAPTURE Hardware Devices ****
card 1: Microphone [Yeti Stereo Microphone], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 2: ALC892 Alt Analog [ALC892 Alt Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
Here is the the output of "arecord -L":
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=Microphone
Yeti Stereo Microphone, USB Audio
Default Audio Device
front:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
Front speakers
surround40:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
4.0 Surround output to Front and Rear speakers
surround41:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Microphone,DEV=0
Yeti Stereo Microphone, USB Audio
IEC958 (S/PDIF) Digital Audio Output
sysdefault:CARD=PCH
HDA Intel PCH, ALC892 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
Front speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC892 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
Here is the output of "aplay -l" (for completeness):
**** List of PLAYBACK Hardware Devices ****
card 0: Audio [USB2.0 High-Speed True HD Audio], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 1: Microphone [Yeti Stereo Microphone], device 0: USB Audio [USB Audio]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 2: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 3: NVidia [HDA NVidia], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
If the output of "aplay -L" is needed, let me know, but it's not all that different from arecord -L.
Here is my /etc/asound.conf:
defaults.pcm.rate_converter "samplerate_best"
pcm.!default {
type pulse
fallback "sysdefault"
hint {
show on
description "Default ALSA Output (currently PulseAudio Sound Server)"
ctl.!default {
type pulse
fallback "sysdefault"
# vim:set ft=alsaconf:
I don't remember where the bulk of that came from; maybe it was installed like that or maybe I put it in there. Here is another useful command showing non-commented-out/non-blank lines in the pulseaudio conf:
$ egrep -v '^;|^#|^$' /etc/pulse/*.conf
/etc/pulse/client.conf:autospawn=no
/etc/pulse/daemon.conf:exit-idle-time=0
/etc/pulse/daemon.conf:default-sample-rate = 192000
So, there's not much I've done there. Here's the contents of /proc/asound/cards:
0 [Audio ]: USB-Audio - USB2.0 High-Speed True HD Audio
CMEDIA USB2.0 High-Speed True HD Audio at usb-0000:00:1d.0-1.7, high speed
1 [Microphone ]: USB-Audio - Yeti Stereo Microphone
Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed
2 [PCH ]: HDA-Intel - HDA Intel PCH
HDA Intel PCH at 0xf7530000 irq 52
3 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xf7080000 irq 17
And here's the contents of /proc/asound/modules:
0 snd_usb_audio
1 snd_usb_audio
2 snd_hda_intel
3 snd_hda_intel
Now, here is the output of "pactl list sources" (the Blue Yeti is last in the list):
Source #3
State: RUNNING
Name: alsa_input.pci-0000_00_1b.0.analog-stereo
Description: Built-in Audio Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 7
Mute: yes
Volume: front-left: 17972 / 27% / -33.71 dB, front-right: 17972 / 27% / -33.71 dB
balance 0.00
Base Volume: 6554 / 10% / -60.00 dB
Monitor of Sink: n/a
Latency: 610 usec, configured 100000 usec
Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY
Properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "ALC892 Analog"
alsa.id = "ALC892 Analog"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "2"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xf7530000 irq 52"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1b.0"
sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card2"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "1e20"
device.product.name = "7 Series/C210 Series Chipset Family High Definition Audio Controller"
device.form_factor = "internal"
device.string = "front:2"
device.buffering.buffer_size = "76800"
device.buffering.fragment_size = "19200"
device.access_mode = "mmap"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "Built-in Audio Analog Stereo"
alsa.mixer_name = "Realtek ALC892"
alsa.components = "HDA:10ec0892,10438436,00100302"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
Ports:
analog-input-front-mic: Front Microphone (priority: 8500, not available)
analog-input-rear-mic: Rear Microphone (priority: 8200, available)
analog-input-linein: Line In (priority: 8100, not available)
Active Port: analog-input-rear-mic
Formats:
pcm
Source #11
State: RUNNING
Name: alsa_output.pci-0000_00_1b.0.analog-stereo.monitor
Description: Monitor of Built-in Audio Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 7
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.pci-0000_00_1b.0.analog-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of Built-in Audio Analog Stereo"
device.class = "monitor"
alsa.card = "2"
alsa.card_name = "HDA Intel PCH"
alsa.long_card_name = "HDA Intel PCH at 0xf7530000 irq 52"
alsa.driver_name = "snd_hda_intel"
device.bus_path = "pci-0000:00:1b.0"
sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card2"
device.bus = "pci"
device.vendor.id = "8086"
device.vendor.name = "Intel Corporation"
device.product.id = "1e20"
device.product.name = "7 Series/C210 Series Chipset Family High Definition Audio Controller"
device.form_factor = "internal"
device.string = "2"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-pci"
Formats:
pcm
Source #15
State: RUNNING
Name: alsa_output.usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio.iec958-stereo.monitor
Description: Monitor of USB2.0 High-Speed True HD Audio Digital Stereo (IEC958)
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 192000Hz
Channel Map: front-left,front-right
Owner Module: 8
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio.iec958-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of USB2.0 High-Speed True HD Audio Digital Stereo (IEC958)"
device.class = "monitor"
alsa.card = "0"
alsa.card_name = "USB2.0 High-Speed True HD Audio"
alsa.long_card_name = "CMEDIA USB2.0 High-Speed True HD Audio at usb-0000:00:1d.0-1.7, high speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.7:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.7/6-1.7:1.0/sound/card0"
udev.id = "usb-CMEDIA_USB2.0_High-Speed_True_HD_Audio-00-Audio"
device.bus = "usb"
device.vendor.id = "0d8c"
device.vendor.name = "C-Media Electronics, Inc."
device.product.id = "0319"
device.product.name = "USB2.0 High-Speed True HD Audio"
device.serial = "CMEDIA_USB2.0_High-Speed_True_HD_Audio"
device.string = "0"
module-udev-detect.discovered = "1"
device.icon_name = "audio-card-usb"
Formats:
pcm
Source #19
State: RUNNING
Name: alsa_output.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.iec958-stereo.monitor
Description: Monitor of Integrated Rate Matching Hub Digital Stereo (IEC958)
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 48000Hz
Channel Map: front-left,front-right
Owner Module: 9
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 65536 / 100% / 0.00 dB
Monitor of Sink: alsa_output.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.iec958-stereo
Latency: 0 usec, configured 100000 usec
Flags: DECIBEL_VOLUME LATENCY
Properties:
device.description = "Monitor of Integrated Rate Matching Hub Digital Stereo (IEC958)"
device.class = "monitor"
alsa.card = "1"
alsa.card_name = "Yeti Stereo Microphone"
alsa.long_card_name = "Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.8:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.8/6-1.8:1.0/sound/card1"
udev.id = "usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone"
device.bus = "usb"
device.vendor.id = "b58e"
device.vendor.name = "Intel Corp."
device.product.id = "9e84"
device.product.name = "Integrated Rate Matching Hub"
device.serial = "Blue_Microphones_Yeti_Stereo_Microphone_REV8"
device.form_factor = "microphone"
device.string = "1"
module-udev-detect.discovered = "1"
device.icon_name = "audio-input-microphone-usb"
Formats:
pcm
Source #23
State: RUNNING
Name: alsa_input.usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone.analog-stereo
Description: Integrated Rate Matching Hub Analog Stereo
Driver: module-alsa-card.c
Sample Specification: s16le 2ch 48000Hz
Channel Map: front-left,front-right
Owner Module: 9
Mute: no
Volume: front-left: 65536 / 100% / 0.00 dB, front-right: 65536 / 100% / 0.00 dB
balance 0.00
Base Volume: 17775 / 27% / -34.00 dB
Monitor of Sink: n/a
Latency: 949811526 usec, configured 100000 usec
Flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY
Properties:
alsa.resolution_bits = "16"
device.api = "alsa"
device.class = "sound"
alsa.class = "generic"
alsa.subclass = "generic-mix"
alsa.name = "USB Audio"
alsa.id = "USB Audio"
alsa.subdevice = "0"
alsa.subdevice_name = "subdevice #0"
alsa.device = "0"
alsa.card = "1"
alsa.card_name = "Yeti Stereo Microphone"
alsa.long_card_name = "Blue Microphones Yeti Stereo Microphone at usb-0000:00:1d.0-1.8, full speed"
alsa.driver_name = "snd_usb_audio"
device.bus_path = "pci-0000:00:1d.0-usb-0:1.8:1.0"
sysfs.path = "/devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1.8/6-1.8:1.0/sound/card1"
udev.id = "usb-Blue_Microphones_Yeti_Stereo_Microphone_REV8-00-Microphone"
device.bus = "usb"
device.vendor.id = "b58e"
device.vendor.name = "Intel Corp."
device.product.id = "9e84"
device.product.name = "Integrated Rate Matching Hub"
device.serial = "Blue_Microphones_Yeti_Stereo_Microphone_REV8"
device.form_factor = "microphone"
device.string = "front:1"
device.buffering.buffer_size = "19200"
device.buffering.fragment_size = "4800"
device.access_mode = "mmap"
device.profile.name = "analog-stereo"
device.profile.description = "Analog Stereo"
device.description = "Integrated Rate Matching Hub Analog Stereo"
alsa.mixer_name = "USB Mixer"
alsa.components = "USBb58e:9e84"
module-udev-detect.discovered = "1"
device.icon_name = "audio-input-microphone-usb"
Ports:
analog-input-mic: Microphone (priority: 8700)
Active Port: analog-input-mic
Formats:
pcm
Honestly, I think that's about all of the configuration info I can give. Here are some screenshots of pavucontrol, though, in case you are not yet sated: http://imgur.com/a/ngyLl
Now, on to the debugging stuff. First: everything except Blue Yeti recording works. The external DAC works, the on-board audio (both input and output) work, using the DAC in the Blue Yeti to play music/monitor the microphone works (so it works as an output). The only thing that doesn't work is actual recording from the Blue Yeti itself.
When I try to record from the Blue Yeti with parecord -v, I get very strange behavior. Essentially, the "latency" of the microphone measured is exactly the same as the time it has been recording. That is, if it has been recording for 5 sec, then the latency is 5000000 usec. Also, if I try to record something in Audacity, I get no result except for a message box that says "Latency Correction has caused the recorded audio to be hidden before zero. Audacity has brought it back to start at zero." Also, pavucontrol doesn't show an input volume bar for the Blue Yeti, as in the above screenshots, whereas it normally will for microphones that are getting input. The Yeti is not muted, either, so it should be picking up ambient fan noise and such.
Does anyone have any ideas? Is there some configuration error I've made? Typically, this sort of stuff simply works out of the box for me, so I am somewhat stuck on what to do. Could it be a driver-level bug?

I'm not sure what you mean by "mixed with audio in Alsamixer". Can you clarify?
With that said, my problem did mysteriously fix itself after some update (presumably to alsa). Unfortunately, I noticed it in passing one day while I was changing the volume of something in pavucontrol, so I don't remember the exact update that caused it to work. But yes, my current setup does work now: I can listen to audio through my DAC and use the Yeti for recording. However, I have found that use of the Yeti crashes Google Hangouts, although it works perfectly in every other program I've tried.
As documentation, here is my current working setup (it is very similar to the above): in PulseAudio, the DAC is set to be a Digital Stereo (IEC958) output. The Yeti (called an 'Integrated Rate Matching Hub' in pavucontrol) is set to be an Analog Stereo Input. In the input devices section, I have the Yeti's volume set to around 58% (-14.31 dB), which is past the base volume a fair ways but produces decent levels for recording. The DAC's volume is set to 100% (0dB gain, the DAC takes care of the level). In alsamixer, I have the mic level for the Yeti set to 40.
Edit: This is a long-time-later edit, but let me say that when you have multiple USB audio devices, what USB hub and in what order they are connected seems to matter a great deal. If you can't get your Blue Yeti to work, try moving it to a different set of USB ports (controlled by a different controller) on your motherboard. This magically fixes the issue for me.
Last edited by rwiggins (2014-12-14 00:26:39)

I have three Blue Yeti USB Microphones, and when I try to create an aggregate device in Audio MIDI on my MBP it lets me select two microphones but not the third. I need all three for a podcast, any solutions?

I have three Blue Yeti USB Microphones, and when I try to create an aggregate device in Audio MIDI on my MBP it lets me select two microphones but not the third. At first I thought maybe the third microphone was just defected or something but I tested the mic individually and it works fine. It'll let me use two Blue Yeti's and another microphone but not three Yeti's at once.

David Boroditsky wrote:
The problem is that the mac chokes on having 2 identical mics attached at the same time.
Ive had 2 identical USB AT2020 mics connected at the same time on both macbook pro and macbook Air.
The "Yeti" mics, are, lets say undesirable, and low to mid computer consumer mics.

Kernel Panic when using Garageband with Blue Snowball USB mic

*HI ALL,*
*I purchased Mac Pro recently about 3 weeks ago. I am on the latest updates including the recent firmware update. However whenever I use garageband with external USB mic(Blue Snowball) my Kernel Panics and OS freezes and forces me to Power On again. It happened 20 times so far in few hours.*
*I opened garageband first time today after bought this external mic from apple store. I did not use garageband without this mic plugged into USB, I only used garageband with MIC plugged in and in couple of minutes to 5 minutes of using garageband the Kernel Panic occurs. Need your help please. Here is the message I get after login again which I reported consistently to Apple. Any immediate help is appreciated. I use iMove, iPhoto and other apps without any problem. Harddisk verification went o.k.*
Sun Apr 6 22:13:35 2008
panic(cpu 7 caller 0x001A8C8A): Kernel trap at 0x004209d5, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x0000000c, CR3: 0x013fe000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x0ea7c3c0, ECX: 0x1059f4f0, EDX: 0x85ccfb8c
CR2: 0x0000000c, EBP: 0x85ccfb08, ESI: 0x0ea7c3c8, EDI: 0x0ea7c3d0
EFL: 0x00010202, EIP: 0x004209d5, CS: 0x00000008, DS: 0x11ac0010
Error code: 0x00000002
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x85ccf8f8 : 0x12b0f7 (0x4581f4 0x85ccf92c 0x133230 0x0)
0x85ccf948 : 0x1a8c8a (0x461720 0x4209d5 0xe 0x460ed0)
0x85ccfa28 : 0x19ece5 (0x85ccfa40 0x4256f6 0x85ccfb08 0x4209d5)
0x85ccfa38 : 0x4209d5 (0xe 0x85cc0048 0x10 0xe920010)
0x85ccfb08 : 0x42028d (0xea7c3c0 0x85ccfb8c 0x0 0x0)
0x85ccfb58 : 0x420c0e (0xea8b700 0x420978 0x85ccfb8c 0x0)
0x85ccfba8 : 0x6055d9 (0xea7c3c0 0x0 0x85ccfc08 0x615b08)
0x85ccfc08 : 0x609a11 (0xe92a000 0xeed0240 0xf56bff 0x0)
0x85ccfc68 : 0x86334bde (0x13c56800 0xeed0240 0xf56bff 0x0)
0x85ccfcd8 : 0x86334ddd (0xfbe4400 0x2 0x1 0x14)
0x85ccfcf8 : 0x86335056 (0xfbe4400 0x14 0xf7f4a80 0x7c79d6)
0x85ccfd38 : 0x86335156 (0xfbe4400 0x54 0x0 0xf7f4a80)
0x85ccfd88 : 0x9f2e64 (0xfbe4400 0x8634d000 0x862c1010 0x110a)
0x85ccfdf8 : 0x9eec9f (0xfd03600 0x10506588 0x110a 0x3ea740)
0x85ccfe68 : 0x9ee169 (0x13d7d000 0x110a 0x13c4c940 0x13dbab7c)
0x85ccfea8 : 0x43c47e (0x13d7d000 0x110a 0x55f 0x1)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AppleUSBAudio(2.5.4b4)@0x86326000->0x8634cfff
dependency: com.apple.iokit.IOAudioFamily(1.6.4b7)@0x9e4000
dependency: com.apple.iokit.IOUSBFamily(3.0.8)@0x5ff000
com.apple.iokit.IOAudioFamily(1.6.4b7)@0x9e4000->0x9fafff
dependency: com.apple.kext.OSvKernDSPLib(1.1)@0x9e1000
com.apple.iokit.IOUSBFamily(3.0.8)@0x5ff000->0x626fff
BSD process name corresponding to current thread: GarageBand
Mac OS version:
9C7010
Kernel version:
Darwin Kernel Version 9.2.2: Tue Mar 4 21:17:34 PST 2008; root:xnu-1228.4.31~1/RELEASE_I386
System model name: MacPro3,1 (Mac-F42C88C8)

I've been getting a number of kernel panics when using USB Mics with Skype, though I have not experienced any crashes when using Garageband.
The crash report cited the AppleUSBAudio driver as the culprit. Here's the set up:
MacBookPro Core2 2.66 15"
Mac OS X 10.5.2
Blue Snowflake USB Mic, Blue Snowball USB Mic
Skype (latest rev - 2.7.0.257)
AppleUSBAudio.kext version 2.5.6b3
Seems to be a lot of crashiness with USB Audio in 10.5.2 - let's hope we see a patch soon

My Mac Mini isn't recognizing my Blue Yeti (USB) microphone.

I've had both Mac mini & Blue Yeti for about a year. They both individually work perfectly fine, but it wasn't until recently I decided to use the mic on my mini.
When I plug my Blue Yeti microphone into the USB port on the back of the Mac Mini, the light on the microphone turns on. In which indicating that the microphone is on. Yet, when in applications such as audacity, garage band, and reaper it will not recognize the microphone. Disabling me from recording at all. (I also tried Mac preferences via audio, to see if it appears there. Unsuccessful.)

Yes, when i go to System Preferences>Sounds>input the only thing that appears is
And also all the ports work, ive tested it out with my iphone charger.
How do i look up the system report ?

Blue Yeti Pro Mic recognized but not working

I just recently got a Blue Yeti Pro and I can't get it to work on my Mac. There is no sound coming out of it. It only seems to work when I plug in the headphones. The red light is on, I've tried restarting my Mac, plugging and unplugging the mic, updated my OS, switching usb ports. Nothing seem to work! HELP!!!

WHEN IT'S SELECTED, THE INPUT VOLUME IS GREYED
THAT IS NOT YOUR PROBLEM, SOMETHING ELSE IS:
http://www.bulletsandbones.com/GB/GBFAQ.html#volumesliderdisabled

Yeti USB mic not recognized

Hi, I'm new on this stuff
well today I bought the Yeti USB microphone but it seems that is not working and is not recognized by any usb port on my iMac
I did just as the manual said and I quote it:
"1. Plug the microphone into your computer’s USB port using the provided USB cable.
2. From the main Apple menu, select the “System Preferences.”
3. Select the “Sound” icon.
4. Now select the input tab and select “Yeti Stereo Microphone.” "
When I plug the mic the mute button turns on like for a second and then its off
also the Yeti Stereo Microphone does not appears...
I would thank you if anyone could help me out

If you have followed the directions exactly, it may be that the unit is defective. Return it and try another one.
Let us know how you make out,

PP does not see my yeti USB mic even though System control panel does??

Not sure why this is not working..
Thanks
John

This is not unexpected. USB audio is iffy.
Use a normal mic plugged into the Mic input on your rig.

Output sound distortion when USB Mic Connected

Hi everyone,
Really appreciate anyone’s help on this sound distortion problem.
I have been using the new 2014 iMac 27' for last 8 Months, bought Brand New, and recently updated to Yosemite. Everything worked fine including recording, until this update.
I'm using Blue Yeti USB Mic for recording, and few days after the update I was trying to record in GarageBand and the output sound (via headphone connected to USB MIc) started to distort and then suddenly dropped the bitrate/ sound and I could only hear some clicks. I reinstalled the GargeBand, still its the same distortion happens. The sound gets back to normal, only for few seconds, after I unplug the USB cable from the Mic device. And I tried changing the bit rate and again sounds starts to drop after few sec. This happens only when I connect the Blue Yeti USB Mic and sound output from the Mic itself. Same thing happens with iTunes as well. Output sound from Internal mic and speakers are working fine as normal.
I tried connecting the USB Mic to my Windows laptop and its working fine with the Cubase 5 without any problem. So the problem is with the output sound, when external Mic connected.
I don’t know the solution for this. Have checked on every single blog/ thread, sill couldn’t find the answer I’m looking for, to fix this.
It would be great if you have any kind of a solution for the same.
Info : FYI
Mac
OS X Yosemite: Version 10.10.2
iMac (27-inch, Late 2013)
Processor : 3.2 GHz Intel Core i5
Hard-drive : 1 TB SATA Disk
Ram: 8 GB 1600 MHz DDR3
Graphics: NVIDIA GeForce GT 755M 1024 MB
Built-in Output:
Default System Output Device:       Yes
Manufacturer:                                  Apple Inc.
Output Channels:                             2
Current SampleRate:                      48000
Transport:                                        Built-in
Yeti Stereo Microphone:
Default Input Device:                      Yes
Default Output Device:                    Yes
Input Channels:                               2
Manufacturer:                                 Blue Microphones
Output Channels:                            2
Current SampleRate:                      48000
Transport:

Nope. The larger buffer didn't work. What did work was running a cord out of the 1/4-inch jack from the direct box to a 1/4-to-1/8-inch adapter and then into the mic/line-in jack on my computer. I set GarageBand to use the built-in line-in and had no static problems. It's a stopgap until this gets fixed.
A post by LinuxMercedes on Oct. 3 at http://discussions.apple.com/message.jspa?messageID=8158914 may provide a solution.

USB Mics, Sampling Rates and "dumb" apps--help please

I hope someone here can explain this better than the support people at Blue did.
I have a Blue Yeti USB mic. It has a fixed output of 16 bits/ 48kHz. In most recording apps, I can set the sample rate in the app to match at 48kHz. What happens when using this mic with a "dumb" app like Camfrog or Skype, where the user cannot set a matching sample rate in the app? Will the pitch be affected due to the 48 kHz fixed rate of the mic, as opposed to a more common 44.1 kHz?
Any insight into this would be great. I could ask people on Camfrog if my voice sounds right, but they don't know what my normal voice sounds like!
Thank you.

Darn. Not being able to type at login sounds like an issue mine has every so often, although if you don't log in RIGHT AWAY on mine, you have to force it down and restart because when you type, it pinwheels and never stops. Mine also hasn't been able to restart or shutdown so I haven't been able to apply updates.

IPad 3 Blue yeti too much power warning

unable to use Blue Yeti USB mic with garageband on iPad 3 "too much power needed" warning

I have an almost identical problem with a mac mini connected to a Dell monitor usb hub .. eveytime the computer wakes up I get this message, however no usb devices are turned on (other than keyboard and mouse) and the monitor hub is connected to a webcam( not on ) and a printer (also not on ). The problem seems to be the hub because if I connect the keyboard to the hub I need to use the mouse to wake the mac up. I suspect this happens when the dell monitor is off or goes into powersave mode. Once the mac and dell are both awake everything functions normally so the message seems to be erroneous .. I'd just like to stop it appearing ... any Ideas?

Blue Snowball USB microphone will not connect to audio hardware

My new Blue Snowball USB mic will not connect to the audio hardware in Premiere Pro. It connects well to my Mac but I cannot select it in Premiere Pro. Anyone know of a workaround or some help?

I was able to solve the problem by adding a Mono track first, then recording to that track. It's strange I have to do this, I have a Windows laptop at home that I use with CC 2014 and a Blue Yeti and Premiere just "knows" that I'm trying to record and makes the change.

Help With Audition CS6: Adding windows sound to accompany USB Mic

Hey Guys,
I have a Blue Yeti USB microphone that I wil be using to create a podcast with a friend over skype. When I am setting up audition cs6 I cannot seem to get the USB mic AND skype audio to be recording at the same time. Is this because I do not have a dedicated sound card, or is there something else I am missing?
On a side note, when I set the multitrack to the stereo mix, it says that there are two different types of audio signals and wont record.
Thanks for your help!

dancalgary wrote:
I have been using Audition on this computer for the past few months now. The computer itself is an Alienware laptop, with the most optimal specifications we could get. So right away ram, disk space, disk writing speed, processor, and sound hardware should not be an issue at all.
I take it that you are using the internal sound hardware, then. If this is the case, then you could easily have problems with the sound device, because there isn't a single laptop made that has a decent sound system in it. For a start, none of them support ASIO - which is inherently what Audition uses to produce its output. What happens to get around this is that Audition has to provide an internal extra driver to drive the default sound driver, and this is at best a compromise. If you want decent sound from a laptop, then you need an external sound device with an ASIO driver.
As for W8, well I'm with Bob on this one. It's new, slightly weird, and as with all M$ operating systems, all bets are off until at least the first service pack is issued. If you have anti-virus software that's any more aggressive than AVG, then turn it off. The other common gotcha is wifi - some systems manage to give a massively high priority to wifi polling, and sometimes just turning it off completely is the only way to get any sort of performance at all. I must say though that lately this doesn't seem to have been anything like as much of an issue as it used to be back in the bad old days...
But, if you have badly stuttering playback, then it sounds as though your HD streaming isn't working as it should, and that something else is getting priority access to the drive - which is sometimes where virus scans can catch you out. You really do need to stop pretty much everything unnecessary running, one way or another. And get an external sound device that uses ASIO - this effectively bypasses most of the OS, and gives Audition pretty direct access to the device.

Blue Yeti microphone being activated by OS - won't stay muted!

I upgraded to Yosemite last night and I love it but for one very annoying bug: I use a Blue Yeti USB microphone as my input device, but since it has such an active diaphragm I keep it muted using the front mute button (turning the input to zero doesn't quite do it) to prevent feedback. Since upgrading, there are a huge number of applications that "un-mute" the mic without my input. Anything, it seems, that might potentially use a microphone activates it. As a result, if I have music playing I will suddenly have the mic feeding back without my consent - very annoying! Is there a fix to this? Any ideas?

It seems that any time a system sound of any kind is played it trips the mute switch. Very annoying.

Blue Yeti USB mic is SUPER loud!

Similar Messages

Maybe you are looking for