Bluetooth disconnects when using speed dial

When I make a call by dialing the number or taking it from my contacts, the bluetooth headset acts normally. When I dial a contact via speed dial, the bluetooth disconnects and I have to go into the menu and "activate headset" Any thoughts?? Thx

I have the exact same problem. I have had the Pearl since it came out and never had an issue. I just received the 8900 and I now have this issue which is more than annoying. Any help would be appreciated.

Similar Messages

Nokia Car Mode on N8 - Bluetooth disconnects when ...

After recently upgrading to Belle, I installed Nokia Car Mode because it is what I had been looking forward to the most. However it simply disconnects the Bluetooth connection to my car's audio system a few seconds (maybe 5 seconds) after I enter the Music module.
Steps to recreate:
Start car (1999 BMW M3 running DICE Mediabridge 1500 connected to CD43 head-unit). Car's Bluetooth mode is on and car is discoverable.
Launch Nokia Car Mode on Nokia N8
Pair phone with car using the Bluetooth pairing button on the launch screen. Pairing is successful so continue by pressing the Start Car Mode button.
Press on the Music button to enter the Music module. Music attempts to start playing automatically. The display on the head-unit says "PLAYING", but no sound from the speakers and then the BT connection ends in about 5 seconds.
Thinking that perhaps my old BT pairing info might be saved/corrupted and not usable with the new Belle firmware, I performed a complete reset and re-installed Belle using a tool whose named I should not mention, but no luck even with a pristine build.
If I uninstall Car Mode from my phone, I can connect to my car and play music just fine. If you have navigation running simultaneously, the navigation prompts get routed through the car audio by virtue of the music player's streaming. However as soon as I re-install Car Mode, the same problem begins and remains until I uninstall it again. (If you don't uninstall Car Mode from your phone, it will launch itself automatically when it detects a BT connection with a car using the relevant BT profile.)
Here's another observation: During the 5 seconds that the phone has not yet disconnected, the Music Player's progress bar moves at a rate of about 1 second forward for every 5 seconds elapsed. So it is as if Car Mode introduces a performance issue to the playback.
So now I am living with the way things were in the Anna days: I can play music and navigation audio through my car just fine, but I really wish I had the extreme convenience that Nokia Car Mode provides (when it works as designed).
Solved!
Go to Solution.

I just installed Car Mode on my Belle-equipped N8. I have two serious complaints (not sure if this is the best place to post, but here goes
a) (Really inconvenient!) My speed dials DONT WORK! If I press and hold "2" in regular mode, I speed-dial home. In Car Mode, I just see the "2" appear, and it keeps beeping the longer I hold it! There does not appear to be a way to use speed-dial in Car Mode, which is a #FAIL (in my opinion.) You ought to be able to somehow configure this.
b) I love Internet Radio. When you select Music, you go right into the music player and can never select Internet Radio. You ought to be able to add other audio applications to the Music button.
Thanks for listening!

My car bluetooth disconnects when answering a call.

My car bluetooth disconnects when answering a call?

So does mine - but keeps the call going so then have to risk picking up the phone and putting it on speaker - although friends android phone works perfectly - i'm fed up - i have an iphone 5 and i would expect that with paying 600 for a phone and using it in a 40k car - there shouldn't be an issue, but no - my question is why weren't these things adressed before it was issued? - instead of being told ***** to be you but that's just the way it is. Is apple going to pay my fines $300 each for touching my phone while driving - aus law, and finally when i lose my licence because each fine is 3 points are they going to provide a chauffeur?. Apple need to remember before the iphone they were very small indeed, and only big in the graphic art industry. With Androids getting better and better there's now alternatives and the thing is i quit iphone, i quit the rest of the suite as well - ipads, itunes, apps, as well as mac books, and let's not forget ipods - which means i won't be updating any of those either. I'll rather buy Samsung tablet and an android phone and then i'll buy android apps, and update android. Apple need to remember customers vote with their feet, and IBM nearly went under because of it's own arrogance - could it be apple are going the same way?

Bluetooth issues when using smartwatch on the z1s

I'm having some Bluetooth issues when using my smartwatch. I usually use my z1s with my car radio via Bluetooth to listen to music and for making calls. Now that I got a sony smartwatch I always got problems with the calls. It looks like that the Bluetooth turns off during the call when I'm using the smartwatch. I already tried by deleting and pairing again the z1s, but nothing works. Not sure if maybe the z1s does not support the smartwatch and the care radio Bluetooth connection at the same time. However it works fine when playing music! The problem is just with the calls. This never happens before I got the smartwatch.

I have the Tmobile Z1s and a SW2 and have the same issues with multiple devices:
1) Bose Soundlink Mini
2) Sony MBR-100
3) My car's bluetooth
4) Ford Sync
5) Sony SBH20
6) Motorola S305
If the phone connects to the A2DB device, it will typically play fine for several minutes. Then, audio will drop out. If I do nothing, after several minutes my watch will vibrate to show it has disconnected. Sometimes audio then comes back, and sometimes it doesn't.
Sometimes my phone will not connect to my car. Then, if I can get it to connect, it will only allow for phone audio, not media audio.
This issue has been on (2) Z1s's with the SW2. The first I returned due to touch screen issues, which the second one also has. All of the devices above worked perfectly fine with my Xperia Z, Galaxy S2, HTC One, etc. The Xperia Z and the SW2 never had any problems.
Honestly, this phone has been incredibly frustrating. If the upcoming updates for either the SW2 or Z1S don't fix this issue, I'm going to return it and get something else.

Ichat, AIM, & Adium all frequently disconnect when using Air

Ichat, AIM, & Adium all frequently disconnect when using Airport. I use a Linksys Wireless Router with an Airport extreme card. When directly connected to the router, I have no problem. Using a PC with Windows XP, AIM operates fine. Safari and Firefox work fine, although sometimes I receive errors connecting to pages, when I try again no problem. Using any of the chat programs, I lose connection, but then can reconnect. After a few times, the AOL servers will prevent login.
I use COMCAST Cable internet service. My wireless router uses WEP encryption. I would switch to an AIrport Base station, but doubt it would correct the problem.
I have had this problem previously, but it corrected itself. now it is making chat programs unusable.
Any ideas?

Hi John,
By default Linksys units normally have the IP address of 192.168.1.1
Is this true for both your units or have you changed one of them ?
You may only find this out if you connect directly to the Modem one.
Also you have not said if only one of them is doing DHCP.
Example pic 3 on this page. This shows this device as getting it own contact IP address by DHCP (like from your ISP). Further down the page in the pic it shows the device is also acting as a DHCP server to the local net.
If your router is set up like this it could be getting an IP address usng DHCP like this device shows and that would tend to mean that the Modem is acting as a DHCP server as well.
If both devices still have the default IP addresses you will have conflicts, which probably explians the problems you have.
Ralph

Some RST are seen during TCP disconnection when using SSL connection

Some RST are seen during TCP disconnection when using SSL connection
It is expected that the disconnection sequence for a secure connection to be as follow:
client ************************* server
--- alert (warning, close notify) --->
<--- alert (warning, close notify) ---
in any order;
and then:-
--------------- FIN, ACK ------------>
<----------- FIN, ACK ---------------
------------------ ACK ----------------->
Instead of the sequence described above, the TCP connection for a secure connection is closed with an RST.
For instance, Wireshark capture shows that an SSL+SASL TCP connection is closed in the following manner:
client ************************** server
--- alert (warning, close notify) ---->
---------------- FIN, ACK ------------>
<--- alert (warning, close notify) ---
<----------- FIN, ACK ---------------------
------------ RST -----------------> *(This RST message should be investigated, an ACK message was expected)*
Server: OpenLDAP: slapd 2.4.23
Client: (java version "1.6.0_16")
import javax.naming.*;
import javax.naming.directory.*;
import javax.naming.ldap.InitialLdapContext;
import java.util.Hashtable;
import javax.naming.ldap.InitialLdapContext;
import javax.naming.ldap.StartTlsRequest;
import javax.naming.ldap.StartTlsResponse;
class Client {
private static final String DEFAULT_INITIAL_CONTEXT_FACTORY = "com.sun.jndi.ldap.LdapCtxFactory";
public static void main(String[] args) {
//SSL
try {
System.setProperty("javax.net.ssl.keyStore", "c:\\\keystore");
System.setProperty("javax.net.ssl.keyStorePassword", "adminadmin");
System.setProperty("javax.net.ssl.trustStore","c:\\\keystore");
System.setProperty("javax.net.ssl.trustStorePassword","adminadmin");
// Set up environment for creating initial context
Hashtable env = new Hashtable(11);
env.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.ldap.LdapCtxFactory");
// Must use the name of the server that is found in its certificate
env.put(Context.PROVIDER_URL, "ldap://1.2.4.4:16415");
env.put(Context.SECURITY_AUTHENTICATION, "simple");
env.put(Context.SECURITY_PRINCIPAL, "cn=manager,dc=operator,dc=com");
env.put(Context.SECURITY_CREDENTIALS, "password");
env.put(Context.SECURITY_PROTOCOL, "ssl");
// Create initial context
InitialLdapContext ctx = new InitialLdapContext(env, null);
// Close the context when we're done
ctx.close();
catch(Exception e)
e.printStackTrace();
Is it a bug ? Can I expect to have a patch for this issue?
Regards,
Olivier
Edited by: 975464 on 6-Dec-2012 11:21 AM

I agree it should be an ACK not an RST but it doesn't really matter. The connection is closed, and as neither the client nor the server has any pending data it is benign. Worth investigating in a later JRE.

Detect Client Disconnect When using RTMP

Hello,
I hava a Java Server and Clients using RTMP. I've read somewhere that I can detect instantly client disconnection when using RTMP. However I cannot find an example code (in Java) that demonstrates this functionality? Can you help me please?

I am not sure how your client looks, however the lient connect using NetConnection under the hood which spits NetStatusEvents's and you can listen to them ...
C

Network disconnects when using youtube on ipad air

network disconnects and turns it self off when using youtube app on ipad air

Hello paulm250m
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Wi-Fi disconnects or signal strength is less than expected
Move closer to the Wi-Fi router (access point).
Check for sources of potential interference.
Remove any case, stand, or other accessories from your iOS device and see if signal strength improves.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Best of luck,
Mario

FMS auto disconnects when using a class

I am trying to implement a very simple class that will create
an instance of the NetConnection object and connect to the FMS
server. However, the client will connect then immediately
disconnect when the swf is published. My code is as follows...
FLA Code:
import _includes.*;
var obj_conn:Conn = new Conn();
obj_conn.connect();
Conn.as Code:
class _includes.Conn
public function Conn()
public function connect()
var nc:NetConnection = new NetConnection();
nc.connect("rtmp://localhost/classtest");
Please note that the connection works fine if I just create a
NetConnection variable on the FLA itself in the timeline. Any
suggestions/help would be appriciated!

it think this is happen because you use local variable : your
variable is delete at the end of connect() so your NetConnection
will be closed in the same time.
try this:
Conn.as Code:
class _includes.Conn
private var objNetCon:NetConnection;
public function Conn()
public function connect()
this.objNetCon = new NetConnection();
this.objNetCon.connect("rtmp://localhost/classtest");
}

Using speed dial button as paging on provisioned 525g's

Hello everyone!
We recently switched to a hosted phone provider with provisoning for our 2 SPA525G2's but still want to maintain an internal paging function between them using a speed dial button. For less confusion, lets call in ex5.
I have successfully created a dial plan and am able to dial *96 + extension number to activate the paging system. My objective is to just hit ex5 and having it automatically activate the paging function.
I feel I'm very close but need help with the last step.
Please help!

Thanks for your response!
Question, wouldn't that use my provisioned phone system still? How could I directly dial the LAN side IP?
I currently have (<5:[email protected]:5060>S0|xx.<:@192.168.0.104:5061>) which allows me to call the other phone but not page it.

IPhone Wifi and Bluetooth interference when used simultaneously

I am presently using AirFoiI to stream audio from my PC to my iPhone. AirFoil uses the same protocols as AirPlay. AirFoil/AirPlay streams an Alac audio codec using a bandwith of 1,50 Mbs on average irrespective of the audio codec and bit rate of the source file.
The audio stream received on my iPhone through WiFi is send over simultaneously to my Bluetooth speaker.
When using AirFoil/AirPlay, I regularly hear distortions at the beginning of a track and also randomly when a track is playing. The distortions are a lot more when I move the iPhone around. I am almost 100% sure that these sound distortions are because of Bluetooth interference on the iPhone itself when simultaneously receiving an audio stream from AirFoil/AirPlay and sending an audio stream over bluetooth to my speaker.
I also have done some tests using "Net Meter" and "TCP-view" from Sysinternals on my Windows 7 PC. On "Net Meter" I have never seen any WiFi drop outs or distortions regarding my home network.
My bluetooth speaker supports the A2DP AAC audio codec. This was an important feature for me before I bought the device because the AAC audio codec provides normally a relatively good audio quality over Bluetooth. At the time it did not occur to me that there might be a possible Bluetooth interference coming from my iPhone itself. I presumed that the Bluetooth on the iPhone would use a 2,4 Ghz RF channel not in use by WiFi so that WiFi and Bluetooth used on the same device simultaneously could never distort each other. I was clearly wrong. Put shortly, the problems I encounter are presumably solely caused by the firmware/software on my iPhone. I hope this will eventually be resolved with some future iOs 8 updates. There were indeed many people having Bluetooth issues since iOs 8.
I know the best solution would be to wire my speaker optically with an AirPort Express or an Apple TV. I have not yet decided between the two.
Even when there exists a "wired" solution, I think an expensive device such as an iPhone should be able to make sure that there is never interference between WiFi and Bluetooth when used simultaneously on the SAME device/iPhone.
I hope that some specialists will give their views on my "nonprofessional" analysis and some more in-depth information.

Now will this work:
Airport extreme set to BOTH frequencies and my older wifi stuff like Iphone and printer will automatically connect via 2.4GHz and Macbook will connect to 5GHz so that it will not longe be disruppted by bluetooth?
Unfortunately, no one can predict exactly what will happen in advance with wireless and interference issues. Your chances will improve, though. It might be a good idea to understand the store's return policy before you buy.
What if the Macbook will not connect automatically to the 5Ghz network because the 2.4 stream may be slightly stronger. Is there a way to force macbook to connect to 5Ghz?
Yes, use the option to assign a separate wireless network name to the 5 GHz band, and then "point" your MacBook to that network. The other 2.4 GHz devices will connect to the 2.4 GHz band.

N82 restart when tryine to use speed dial 1

Hi,
When i press and hold 1 to access my voicemail my phone restarts.. It just seemed to happn, no changes were made to the phone. I recently installed the newest firmware but it didnt fix it... Any ideas?
Thanks
Chris

You could try doing a restore factory default settings. It won't delete any data of yours, you'll juet have to redo your theme, ringtone, wallpaper etc. settings afterwards.
Enter *#7780# from the standby screen and then supply your security code (12345 unless you've changed it).
I doubt it'll work but it's worth a shot.
The N82 was one of the first phones to have UDP, so maybe a reset might help.
Back up all your data to a computer using PC Suite and then enter *#7370# from standby and provide the security code when prompted.
Check to see if it works now. If it does, restore your data from the backup.
Try again.
If it no longer works then your data was corrupt. Reset the phone again and then restore everything but your settings. If it continues to stop working after a restore then repeat the reset and restore one less element of the backup each time until you narrow it down to the part that's causing the problem, then finally do a last reset and restore all but that element.
If none of the above work then you'll need to take/send the phone into your local Nokia Care Point.
Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

T440p: internet disconnects when using BT mouse

I have the 2x2 Thinkpad wireless card and when I use my bluetooth mouse the internet disconnects and I get a "limited connection". I have the latest drivers for everything.

Hi iphetamine and Jakoob,
Remember that this is users helping users here, moderated by volunteers like me. Although there is some Lenovo presence, they can't patrol the entire community. They do try to help with some of the broader issues.
Any possibility you're in a marginal WiFi reception area, and Bluetooth interferes with it?
I don't work for Lenovo. I'm a crazy volunteer!

Blutooth disconnect when using Skype, now completely fails to reconnect

I have been experiencing the following problem when accepting or placing a video call through Skype. This never happens when running any other software. My system is an ideaCentre B520 with the stock Bluetooth keyboard and mouse using a Broadcom BCM2070 device running firmware 6.5.1.2700 and a Microsoft Bluetooth Enumerator with firmware 6.1.7601.17889.
The Bluetooth mouse and keyboard disconnect during the call and will not pair or connect wit the computer (IdeaCentre B520). The only solution that I have found work, is to remove both devices from the device manager and reconnect with the physical Bluetooth buttons on the computer and the devices. I also un- and reinstalled Skype, but the problem continues, which might be a software issue.
However, today the computer completely failed to pair and connect with the devices. The pairing dialogue is displayed after pushing the Bluetooth button on the computer. I am prompted to press the corresponding buttons on the mouse and the keyboard and the dialogue completes (code number for keyboard is entered) with the message that the pairing was successful, but drivers may need to be updated. The new drivers are installed for the HDI devices as indicated by the bubble and the grey Bluetooth window light the devices as connected. The Bluetooth box will then go into a repeated flickering between connected and disconnected until both devices are deleted from the device manager terminal. Both devices continue to blink as if searching for the receiver.
I had to switch over to a wired mouse and keyboard to type these lines. But this defies the purpose.
I sincerely appreciate any suggestion you might have to solve this problem and get the devices to talk to one another again.
Thanks in advance.
hailaender

You use wrong bluetooth software. The only one that should work is 6.4.0.2100. You can download it from Sony website. I know it may sound strange but I have tested them all. Give it a shot and see what happens.

Apple Wireless Keyboard is lagging and disconnecting when using Macbook Pro via Bootcamp

Hey guys,
I am using my Macbook Pro (I think from 2009) with an external monitor and the apple wireless keyboard (connection via Bluetooth).
First when I set up Bootcamp everything worked fine. But now suddenly the keyboard is lagging (letters sometimes appear after a few seconds or get stuck and typed 20 times or something) and randomly completely disconnecting.
I already downloaded the newest drivers for Boot Camp 64bit from the apple website, but this didnt solve my problem.
I tried disconnecting the keyboard on mac and then reconnecting on the Windows 7 partition again. Also didn't work.
Of course I had to reconnect the keyboard when on the mac.
But it's not that it's not working. I'm using the keyboard via Bootcamp right now. It's just that it's randomly doing this...
Now I don't know what to do. Do some of you have the same issues or have any ideas that might help?

Hey guys,
I am using my Macbook Pro (I think from 2009) with an external monitor and the apple wireless keyboard (connection via Bluetooth).
First when I set up Bootcamp everything worked fine. But now suddenly the keyboard is lagging (letters sometimes appear after a few seconds or get stuck and typed 20 times or something) and randomly completely disconnecting.
I already downloaded the newest drivers for Boot Camp 64bit from the apple website, but this didnt solve my problem.
I tried disconnecting the keyboard on mac and then reconnecting on the Windows 7 partition again. Also didn't work.
Of course I had to reconnect the keyboard when on the mac.
But it's not that it's not working. I'm using the keyboard via Bootcamp right now. It's just that it's randomly doing this...
Now I don't know what to do. Do some of you have the same issues or have any ideas that might help?

Bluetooth disconnects when using speed dial

Similar Messages

Maybe you are looking for