Bluetooth Mouse and Thinkpad T520 not working together at all

Hi All (first post),
System:
Lenovo T520
Windows 7
Microsoft Bluetooth mouse
Problem: Not working at all, or working only sporadically.
History: Laptop is a bit over year old (warranty ends in June 2015 IIRC). The sales clerk recommended a bluetooth mouse, so I bought a Microsoft Bluetooth 5000. After the initial pairing difficulties were resolved, they worked swimmingly for about a year. Then I started more and more frequently having to re-pair them (remove device, let Windows find it again, pair them,...). As the mouse had taken a bit of beating, I bought another one a week ago. Didn't really help. The first time I asked Win7 to find the device, it couldn't. The Bluetooth radio was on, and the mouse had a fresh set of batteries, and all the other braindead suggestions of Win7 were eliminated. The bluetooth radio was working, because it detected the neighbors daughter's smartphone through a concrete wall, but not the mouse. I kept pressing the button in the bottom of the mouse that presumably makes it broadcast "I'm here".
I moved to another room. This time detection and pairing up the device went fine. But after I had switched the laptop and the mouse off, and rebooted - nothing happened. I had to go through the remove/add device cycle again. Moving to a different room again. At first nothing. Then Windows finds the device, but gives the error code 0x800070015 (or something like that, not sure about the number of zeros), and fails to configure it.
Any idea what is going on? Why is this becoming progressively worse?
Elsewhere in this forum it was suggested that I should disallow windows to power off USB root hubs. I tried that but it had no effect.
Regards,
Jyrki

Sorry. The error code was 0x80004005. This is the code I get from Add Device ->, when I try to enter 0000 as the paring code (suggested by the mouse start guide. If I try to pari them without a code, Control Panel first indicates that the piece of Hardware was added ok, but it before I get any use out of the mouse, the freshly added pic of the mouse disappears. The red/green light on the mouse never stops blinking.

Similar Messages

Bluetooth mouse and keyboard do not work

I purchased an iMac G5 about 6 months ago. I got it with a bluetooth mouse and keyboard. I have had trouble with it from day 1. Apple had me replace the logic unit, and it worked for a couple of weeks. Then as soon as the 90-day warranty for complimentary service ran out, it began working sporadically. Now it doesn't work at all. It says I don't have a bluetooth module installed or attached to my computer (which is what it said before the logic unit was replaced. The computer works fine with a USB mouse and keyboard. Had I known bluetooth was so tempermental and difficult, I sure wouldn't have got it with my computer.
Unless there is a smart person out there who knows what is going on, I guess I need to buy a new USB keyboard and mouse. Anybody interested in buying a bluetooth keyboard and mouse cheap?

Russell,
The warranty period on your mac is 1 year. The complimentry phone service period is 90 days unless you have a hardware problem. I'd say you likely have a hardware problem and will not be charged for the phone call.
I'd suggest 2 things:
1. Sign up for Applecare as has been recommended countless times.
2. Make the call to tech support and see what they say about your problem.
Good Luck,
John

Bluetooth Mouse and keyboard STILL Not working can someone help me?

i have an apple Bluetooth Keyboard and wireles mighty mouse. Since i have installed leopard months ago it was working fine but then my mouse and keyboard stopped pairing with my Powerbook it recognises the devices but the refuse to pair i changed the batteries and installed the software that cam ith the keyboard and mouse and still nothing works.
Can someone help me please

After updating to 10.5.2 I am still experiencing problems with my Apple wireless mouse and keyboard. This is a Leopard issue ( here is just one blog on the topic
http://aralbalkan.com/1086 ) in 2005 I purchased a Mac Mini which I love and never experienced a Bluetooth problem till I installed Leopard several months ago, now at least once a week, on average 2-3 times a week, I loose connection with the keyboard or the mouse and it takes awhile to re-establish the connection. I was hoping the last upgrade would address this issue but no such luck.

Can not install windows 7 pro using boot camp as mouse and keyboard will not work Help please

I have a new iMac and trying to install Windows 7 Pro using boot camp. I have reached the stage of starting to load windows from the DVD then discovered the mouse and the keyboards not working so I could not interact with windows installation.

Open, if not so already, the Windows formatter. Identify the BC Windows partition. It will be the one listed with the proper size you created and/or will be labeled as a C: drive. Be careful you select the right one or you may be corrupting the entire drive.
Format the partition as NTFS.

I AM USING KEYBOARD WITHOUT MOUSE AND LETTER "H" NOT WORKING

I AM USING KEYBOARD WITH NO MOUSE AND LETTER "H" NOT WORKING
DOES SOMEONE KNOWS WHAT CAN BE DONE.
THANK YOU
MARIA

I saw this issue before where cause was a bad preference for another application.
When I had the "can't type Shift H" problem in Entourage, it was a corrupt preference for FlightCheck, a preflighting program I use in conjuction with QuarkXPress that was the culprit.
First determine if the problem is in your User’s folder by creating a new User in System Preferences and test for the problem there. If it goes away then you know the problem is in your User’s folder.
Use new User to test for problems
Let us know the results

Touchsmart 520-1047c Mouse and Keyboard will not work after sleep mode

I have an issue which I need some help with. When my computer goes to sleep the wireless mouse and keyboard will not work unless I restart, however each one will wake the system up but will not operate after that. I have tried just making the display go to sleep, both go to sleep but that makes no difference same issue occurs. The only work around I have found is going into the power settings and turning the sleep mode off for booth the computer and display. This does not solve the problem it just masks it. New batteries, unplugged and replugged the dongle, updated the bios and all drivers. Don't know what else to try. Anybody know how to fix this? Thank you in advance for your help.

Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I understand that the mouse and keyboard on your desktop computer does not work if your computer enters sleep mode, and I would be happy to assist you in this matter! To correct this issue, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues (Windows 7). This should help enable your system to wake from sleep mode using your wireless keyboard and mouse. I also recommend connecting wired peripherals to diagnose the functionality of your keyboard and mouse. If your system is still not able to wake from sleep mode, please follow the steps below to restore the default power schemes on your computer: Step 1. Click the Start button
Step 2. In the search box, type "Command Prompt"
Step 3. Right-click Command PromptStep 4. Click Run as administrator
Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
Regards

MAC Mouse and Keyboard Do Not Work, when I am trying to re-install the OS using "Command R" option

I am trying to re-install MAC OS 10.8.2, but when I hold "command R" I am asked for the firmware password, but the keyboard and mouse do not work.
If I only select "option" during the boot up process it will ask me for the firmware password, keyboard and mouse work, but I can only select the HD option.
Can someone advise what is the problem here, and your resolution.
I have tried different commands "option + command + R' with no luck.

I tried what was provided on the link, but it is not working.
I hold it down, before the gray screen and the chime, but it only prompts but the firmware password.
I tried based on the specific order in the support document and at a random press and hold.
No go any other thoughts?

Magic mouse and number keys not working

Last year, Wet Baloney had a problem:
I have a first generation iMac with the wireless keyboard of that vintage and a new Magic Mouse.
All of a sudden the keys on the numeric keypad part of the keyboard do not work. The number
keys at the top do work.
Also (all of a sudden) this computer is not detecting my wireless Magic Mouse. There is no battery
problem. The mouse works fine with my MacBook Pro.
Does anyone have any troubleshooting ideas ??
While this question was not answered, Apple decided to archive it anyway so I'm reposting. I had this problem and my sysadmin wizard figured out what is happening. The solution is to open "System Preferences" --> "Universal Access" and select Mouse. Turn off "Mouse Keys". What I don't know is how that got turned on but it happened when I did a Mac OS update that came out around March 28, 2011. Anyway, that fixed both the mouse and the keypad problems. I'm posting so that someone doing the same search I did can find this answer.

Thank You for this!! I was having problems using my Numeric keypad on a wired keyboard - when I used the number keys, the wireless magic mouse would lock up - the only way out was to Force Close the Application . . . Turning off "Mouse Keys" and hitting Shift > Clear turned everything back to normal.

Bluetooth, iSight and Keyboard Backlight not working. Please help!

My Bluetooth stopped working along with my iSight and Keyboard Backlight. I first noticed the weird sign over the bluetooth icon, and it read "Bluetooth not available". I payed no attention to it for a while until I tried to take a picture with Photo Booth and I read "No camera found", for some reason I tried to dim the backlight on the keyboard and a blocked sign appeared under the brightness level, not letting me do anything (Later I was able to use the backlight with the LabTick app). I have tried everything. SMC, PRAM, NVRAM, logging as diferent and new users, booting in safe mode... every solution I have found on the internet has been tested by me. Then I read this about the Hardware Test solution, and surprisingly after performing the Hardware Test no problems were found! So basically my MacBook Pro (mid 2010) is not having any trouble of any sorts with anything. Then why can't I use Bluetooth, iSight or Key backlighting (which only works through LabTick). Given the fact that the hardware test shows no problems I am not comfortable with the idea of taking it to repair. There MUST be something I can actually do to fix these issues.
Does anybody have any idea? I repeat, these are NOT WORKING, NOT FOUND AND NOT AVAILABLE.
- Keyboard Backlight (Only works through LabTick)
- iSight Camera (Not found by any software)
- Bluetooth (No info appears on the system profile, the icon on the menu bar is completely gone)
All three issues happened at the same time, the night before everything was working perfectly fine.
If anyone could help... please!!!
Summary:
MacBook Pro Mid 2010 (http://support.apple.com/kb/SP583) Unibody, can't take out the battery.
Solutions tried:
- Reset SMC: Turning on while holding Shift + Ctrl + Option + Power Button (This makes my MacBook forget about the battery and start up with really loud fan noise, battery icon appears with an X on it, keyboard backlight buttons work, they show brightness level on screen, but the actual light won't work, no bluetooth, no isight)
-Reset PRAM and NVRAM: Turning on while holding Option + CMD + R + P (I have waited for 2 chimes, 3 chimes and 4 chimes at different times, nothing happens. Light, bluetooth and isight are still gone)
-Holding Power Button for 10 seconds, 20 seconds, longer... nothing changes.
-Creating and logging in as new admin user, nothing changes.
-Deleting the bluetooth.plist file and powering off and on again, also rebooting
-Deleting the SystemConfiguration folder, powering off and on again, also rebooting
-Installing "blueutil", didn't help at all, turned it off via terminal with command blueutil off.
-Performing Apple Hardware Test - Shows no erros or problems on any area after one full hour of testing (Performed the extended testing)
-Leaving it powered off overnight
Please anyone help meee!! I can't afford going crazy!
Thank you so much in advance!
Alvarock.

****UPDATE***
Hi guys i got across this forum after searching for bluetooth, front camera and the most ANNOYING no lost keyboard backligth.
After run all the test, procedures, tweeks and, and everything i remenbered that once i sent my MBP to repair at you bring i break, turns out that the little ribbon flex connector coming from the mother board ( from the rigth to left) was loose since the adhesive wich they used shrink do temp changes, anyhow y popped out the glas and found the flex cable totally sticked to the glass pulling out of the pcb board connector, reinstalled it smoothly and that FIXED the camera, bluetooth and keyboard backlight!..
thats it. hope i helped some frustraded owner.

Hints FIRST_ROWS and order by not working together

Hi,
We are facing an issue like we are using hint FIRST_ROWS with a query which have a order by clause, if we are giving both together
it is not working and if we remove either order by or hint it is working
SELECT /*+FIRST_ROWS*/ * FROM (SELECT MYROWS.*,
ROWNUM RN FROM (SELECT * FROM V_REPORT WHERE START_DATE > '22-SEP-04'
AND END_DATE < '22-SEP-08' AND
(GEO_ID in (select GEO_ID from loc where anc = 0))
ORDER BY
ENTITY,OPERATION,NAME
MYROWS)
A simliar query from other view is working fine.
Please help me on the same.

David_Aldridge wrote:
Solomon Yakobson wrote:
Well, ORDER BY implies all rows must be fetched first and then ordered. So yes, FIRST_ROWS does not make much sense in that situation, does it?.
SY.Not in every case -- sometimes an index can be used by the optimizer to returen rows in the correct order without having identified the entire result set.
FIRST_ROWS is deprecated in favour of FIRST_ROWS(n), by the way. http://download.oracle.com/docs/cd/B19306_01/server.102/b14223/usingpe.htm#i1009413
And even if the result set needs to be ordered and no index can be used to avoid the sort operation Oracle offers for "top n" and "pagination" queries the "ORDER BY STOPKEY" optimization which only keeps the top n rows to sort (probably in memory if n is small enough) and eliminates the remaining ones which can make a huge difference if the volume to sort is large.
I've written a note about issues like that recently.
Regards,
Randolf
Oracle related stuff blog:
http://oracle-randolf.blogspot.com/
SQLTools++ for Oracle (Open source Oracle GUI for Windows):
http://www.sqltools-plusplus.org:7676/
http://sourceforge.net/projects/sqlt-pp/

Mouse and keyboard shortcuts not working

I running Firefox 3.6.12 on a Mint 10 Gnome system. Firefox has worked very well for the past month with no problems. Today the mouse quit working when trying to click on any of the pulled down menus at the top, "File, Edit, View..." it also will not work on any pull down menus on screen, address bar, stumble tools... The shortcut keys for the top menu are also not working, Alt F will not pull the file menu down. The mouse works on links and single buttons such as the stumble button or bookmark buttons. Also, right clicking does not work anywhere in Firefox, but works in other programs.
I have rebooted the system and uninstalled and reinstalled Firefox to no avail. Any help would be greatly appreciated.

I started Firefox in safe mode and everything started working as it should.
Restarted in normal mode and everything is again working, I didn't make any changes.
The theme was set at default as I have never changed it. I installed all the addons when I first got Firefox, no new ones have been added in over a month.
Does starting in safe mode reset the addons and plugins? Curious as to why starting in safe mode corrected the problem.

Mouse and trackpad just not working - can't use machine

Hi there,
I have a late 2009 iMac running an up to date version of Mountain Lion and all has been well until today.
My iMac behaving very oddly with my trackpad. I have tried switching it our for a wired mouse and I get the same results. This is what I am experiencing:
The iMac behaves as though I have either:
clicked and held my finger down - on my desktop when I move the cursor around the iMac thinks I'm trying to select an area
right clicked - when I try and click on an icon in the dock, the right click options appear
Additionally I am experiencing the following
iMac doesn't respond to me clicking on an icon
I can't select an option, ie if I do select an option such as 'Continue' (more of that later*) I can't get the iMac to respond to me clicking it
Before switching over to my mouse I replaced the batteries in my BT keyboard and the trackpad. I've also tried attaching a USB keyboard (albeit a PC one)
I have tried the following:
resetting the V/P RAM
booting in Safe Mode
Shutting down, unplugging everything (inc power cord) and left for 10 mins before rebooting
Booting in recovery mode and reinstalling M Lion - I can't even do this
* When presented with the recovery options I can scroll through the 4 options with the up down arrow keys, I can select 'Continue' with the mouse or trackpad (it goes a solid blue colour) but I move forward - either by clicking it or hitting Enter on the keyboard.
I'm now totally stuck as when I reboot (there's been a fair few forced ones) I can't even select my user profile (or any of the Resart/Shut Down options)
Time to make a Genius Bar apppointment, or is there something else I can do?
Thanks
EDIT: I did manage to select my wife's user profile and eventually got into the system, and very strangley if I access the iMac via LogMeIn on my work PC it responds excatly as it should. I can click, select as normal. Even when I'm doing this remotely my trackpad and mouse continue to behave incorrectly (as described above
Message was edited by: TWH3

Man.. I is such a fool sometimes.
So I reinstalled ML - which on my cruddy 4 MB ADSL connection took a fair while. And still the problem was there.
Then I tried one small thing... take the batteries out of the trackpad and then try using the wired mouse. BINGO.
After a few more tests it has bceome clear that it was the trackpad that was at fault. Not my iMac, not my OS. Having it on would screw up what the wired mouse was trying to do. Should've checked that HOURS ago.
I have a spare trackpad (I used to have a Mac from work and bought myself a trackpad for it. No longer have a Mac for work as a switched employers, but ironcially willbe getting one next week!). I have installed the 2nd trackpad and all works fine.
Lesson learned - do more thorough diagnostics!
I'm off to cancel my Genius Bar apppointment

Please help! my iMac keeps freezing, mouse and keyboard do not work after

Early this morning I turned on my iMac and started downloading updates through software update as usual. I was browsing a website in Safari when all of a sudden the "zoom" feature activated itself and I could not turn it off. I restarted and the keyboard started typing different characters but not letters, so I took out my installation CD and it took me quite a while to reboot the computer using the CD as a startup. Since the keyboard had a different input, the C key was not running the CD. I tried loggin into the support page, but it downloaded the links into the desktop. I used system utilities to restart the computer from the CD, I verified the Disk Permissions, then Repaired the permisions, then the Verify Disk and then the Repair disk, in that order. I restarted the computer and everything seemed fine, but after a couple of minutes the mouse starts closing windows, downloading website links into the desktop and then the keyboard freezes and does not let me type! This has repeated over and over, and I don't know what to do!
Posting this message has been quite an achievement, because I have restarted the computer a lot of times in order to finish.
Someone please help! I don't know what else to do!!!
Thanks!

Yes. And since you aren't backed up, you may have to use Prosoft Data Rescue to try to recovery any information that is critical. First though, do you have another Mac you can hook this one up to using Target Disk Mode?
If you do, that's another way to rescue information. Target Disk Mode is explained here:
http://docs.info.apple.com/article.html?artnum=58583
Similarly, if you have a bootable external hard drive, you can try to boot off that with the Startup manager:
http://docs.info.apple.com/article.html?artnum=106178
To rescue your information. This at least will allow you to do further analysis to see what data corruption might have happened. If the drive is invisible when booted off another, that may indicate a directory issue. But first let's see if we can attach or boot off another and see the internal drive of the machine.

My itunes and iphone are not working together. all my software is up to date. what i can do? i need to manage my phone!!

I'm getting extremely frustrated with my iphone and mac.
i have the iphone 4, and the mac is leopard.
I plugged my phone it to manage my music, and a message popped up saying i needed software 10.6.8 or higher.
so i downloaded the 10.7. it's still not working!
i have very little space left on my phone and i need to manage everything.
what do i do??
someone please help!!!!

We need clarification here.
Please don't just state version numbers, also state which software. iTunes 10.7 requires OSX 10.6.8 or higher. Leopard is OSX 10.5.8. You have two alternatives right now. One is to stay with Leopard for a while (ultimately you should upgrade) and install iTunes 10.6.3 which is the last version to work with Leopard. This should work with iOS6 on an iPhone4. The other is to call Apple and order OSX 10.6 (Snow Leopard) and upgrade the computer to 10.6.8 which will allow you to run iTunes 10.7. The caveat is we know nothing about which computer you run and if it even can run any system higher than Leopard.
Here is iTunes 10.6.3
iTunes 10.6.3 - http://support.apple.com/kb/DL1575
If you want to try upgrading:
Get more information about your computer. Go to the Apple in the upper left corner of any window, then "About this Mac" and "More Info..." Copy and paste the information here, but omit the serial number and Hardware UUID (if present). If it says something about Intel or Core Duo or Core 2 Duo in the processor you can upgrade to Snow Leopard (assuming you have sufficient RAM/"memory"). If it says PPC or PowerMac, you cannot.
Kappy 08/2012 post on upgrading to Snow Leopard, then Lion or Mountain Lion - https://discussions.apple.com/message/19401628 - including how to get Snow Leopard and Lion since Apple removed them from the online store.
It would help when posting issues here if you would state exact error messages you see. "It's still not working!" while a description of the situation does not speed us to a diagnosis of the underlying issue.

Looking for a good usb hub that will allow my mouse and external hard to work together

I'm looking for some ideas for a good usb hub that will allow me to use a wireless mouse and an external hard drive at the same time, without shorting out the mouse. The one i currently have, when I plug in just the mouse, it's fine, but as soon as i put the external hard drive into the hub port, the mouse no longer works and i have to reinstall the drivers for the mouse.

Hubs and computers vary in their power needs, but it seems that your setup is lacking in the power department. This isn't a big deal with desktop computers, but since you use a MBP, you're going to do best with a powered USB hub.
If you're looking for a USB hub with power supply, Belkin is generally reliable (and above average in price). But the D-Link is compact, reliable, and has a good price. Aim for a USB 3.0 hub if possible, though 2.0 will work fine with just about anything. Insist on a refund if the hub doesn't work in your system. Make sure it's compact, since you'll be carrrying it around.

Bluetooth Mouse and Thinkpad T520 not working together at all

Similar Messages

Maybe you are looking for