Bluetooth Remote Control Quit Working

I have a new 8350i and downloaded the new 5.0.0.807 (?) version software. For some reason, after doing this, the ability of my Plantronics Voyager 815 headset to perform remote controls (answer, hang up, volume, etc) has quit working. Has anyone else had this happen to them? What can I do to correct this? Thanks in advance!
Solved!
Go to Solution.

I thought I'd lost my mind with this phone.  I too updated my phone with the latest software and now I am having all kinds of bluetooth problems, I have the problem with the remote controls on my headset not working.  I have a problem where if I put the phone in the case while talking to someone it hangs up even though I have it set to NEVER do that.  The phone also is having major pairing issues with the two cars hands free radios I have, once the phone is paired to the radio, I can no longer listen to the car radio, I have to drive in silence, so I go back to the headset, which I cannot answer calls or hang up calls with.  I have pulled the battery, but that is only a temporary fix, it starts misbehaving within a day or two, tops.
I used to love this phone, now I am nothing but frustrated with it.
If anyone hears of a solution that works for more than a day, please post what you did.
Thank You

Similar Messages

  • Nokia Bluetooth Remote Control

    Can someone suggest a Bluetooth remote control app that will work with a Nokia touch screen phone? I've tried Phone Remote Control with some success but its not fully touch screen compliant.
    Thank you in advance.

    Vectir - WiFi and Bluetooth Remote Control should do the job but since you didn't mention your phones model, i can't say for sure. You can check device compatibility on the Vectir Nokia Bluetooth Remote Control page.
    My friend uses this as a touch screen remote control on his 5800 Xpress music. I use in on my N95. Pretty slick app.

  • The remote controls stopped working

    I bought with an official Apple dealer the new i Pod Shuffle (generation 3) to use during my bike rides. After the first ride the remote controls stopped working and the voice over feature spontaneously started repeating the songs title. As well the volume control stopped working altogether. I didn't have time to return the Shuffle after only a week so I disable the voice over feature and keep on using my Shuffle with no volume adjustment, fast forward etc ….
    After a visit to the Apple website I saw that several owners complained about this problem and assumed Apple would know about it and be ready to offer a fast solution. So picked an official Service Center as close as possible from my location.
    First shock the Service Center was dirty, the paint obviously several decades old and faded, the light kept to the minimum.
    Second shock not Tech on duty to check something as simple as a headsets. I realized there was no way to have a fast resolution to my problem. The Shuffle will be send to a regional repair center, I could have save the trip and just go to an Apple dealer. What the use to have Service Centers if they don't provide service?
    Now when a product is returned, after 25 days of ownership (can't say use), a product designed by a company with the reputation of Apple you expect some kind of sign that the company is sorry, stands behind it's product and will do all possible to solve the problem. WRONG.
    Third shock. The person who took my Shuffle obviously never saw a Shuffle generation 3 before or even knew it existed. She explained over and over that I may (but it sounded more like I will) be charge for the repair. Even asked me to pay upfront a basic fee to cover the time of a Tech checking on the product. And that the Tech will give me a quote if I am to be charged. Furthermore She found tons of reasons why eventually I would be charged to repair the product, however no technical person ever checked on the product. Well I guess only users read messages on Apple website not employees of Apple.
    So what now? I am suppose to receive an E-mail in 24 hours to 5 working days, in which I'll be explained the result of the Tech investigation.
    I guess most owners of Apple products have a better experience with the Customer Service or where the reputation of Apple being a “cool” company comes from? But based on my experience it looks like Apple's products and Apple's Customer Service may not meet Apple's reputation or customer's expectations. Or am I asking for too much?

    I seriously doubt you were at an Apple Store and you were not dealing with Apple employees. You were dealing with a 3rd party shop that does work on Apple products.
    Don't know where you are located but you could contact Customer Service at Apple and complain but they are somewhat limited it dealing with a 3rd party company. But they will at least have you complaint on file. Or you could attempt to find an actual Apple Store and take your Shuffle there. Or you could try one of the workarounds listed on the threads here.

  • Remote control stopped working on MacBook Pro

    I have two MacBokk Pros (2008 and 2011), with two remote controls that worked fine and interchangeable until about a week ago. Now both remotes work only on the older one of our computers, but not on the newer one. I have looked into the Security prefs panel, "Disable Infrared Receiver" is unchecked, "this computer will work with any available remote control" is shown underneath - everything look like it was before.
    Holding "Menu" and "Fast Forward" to pair the remote produces no results after 5 seconds or more.
    I also did the the "iSight test" mentioned elsewhere in this forum, the batteries in both remotes are fine and sending a signal.
    That leads me to suspect there might be a problem with the infrared receiver. But is that a hardware or software issue and what should be done next, considering that I'm about 200 miles from the next Apple store?

    Thank you! Yes, I've seen this troubleshooting page and followed those suggestion, that's where I also found the remote control battery test mentioned above.
      Product ID: 0x8242
      Vendor ID: 0x05ac  (Apple Inc.)
      Version: 0.16
      Speed: Up to 1.5 Mb/sec
      Manufacturer: Apple Computer, Inc.
      Location ID: 0xfd110000 / 3
      Current Available (mA): 500
      Current Required (mA): 100
    The only difference here is a "3" in the Location ID where your's shows a "2"
    UPDATE: The SMC Reset tip worked! Thank you!!!  

  • What remote controls will work with the iMac 27inch.

    Okay I hung the new iMac on the wall in my kitchen. Used the apple adapter I have a little apple remote control that works the dvd player fine. Of course the wireless keyboard and the wireless mouse work fine. I have an elgato tuner because this iMac is my dvr/tv does anyone have a remote that will work the iMac as a dvd and work the elgato hybrid tuner. Just trying to make this simple. Thanks

    iTunes itself, that is it's built-in remote speaker function, will work only with an Airport Express. There may be other wireless speakers that have their own drivers or transmitter; someone else here may be able to make a recommendation.
    Message was edited by: Dave Sawyer

  • Remote Control does work with Sylvania Color TV/DVD Model 6520FDF

    I cannot get the remote control to work the volume on a Sylvania Color TV/DVD Model 6520FDF TV.   Can anybody help me?

    Have you tried the scan mode to scan for the proper code?
    TV/DVD combo units are notoriously hard to program to universal remotes.  So if you did a scan and none of them worked then the likelihood is that the remote just will not work with that unit. If you have not tried a scan, here is the instructions to do so.
    WHAT IF NONE OF THE CODES WORKED?
    If none of the codes worked, try the following procedure. (As before, we will use the example of a TV. For other devices use the appropriate Device Key instead of the TV key in step 2 and 3.) 1. Turn on your TV.
    2. Press and hold the TV key.
    3. While holding down the TV key, press OK.  4. Release both keys. The Device Keys will blink twice.5. Press 9 - 2 - 2. 6. Point the remote at the TV.
    7. Press PLAY.8. Press FASTFORWARD (FF). Every time you press FF the remote sends out a new power-off command to the TV. Keep pressing FF until the TV turns off. (You can press REWIND to go back.) 9. When the TV turns off, you have found the right code. Press OK to store this code. Note: There are over 300 TV and DVD codes. The most common codes are tried first, but you may still need to press over 300 times to find the right code. If you reach the end of the list of codes the entire remote will flash twice and return to normal operation. You can exit programming at any time by pressing Exit.
    Message Edited by spacedebrismark on 05-17-2009 02:26 PM
    ====================================================================================
    Error exists between keyboard and chair.

  • Audigy 2 ZS Platinum - Remote Control not work

    hello all.. Sorry for beating a dead horse. My installation on a P4 3.0 ghz machine of the Audigy 2 was flawless. All hardware diagnostics that have been run have been successful. Everything works. I updated all drivers. Everything is functional on the unit.....but...the remote control doesn't work.
    When I got to setup the remote control and it asks to select a transmitter (rm-500) from a drop down list, it shows rm-500. but it the drop down list for the receiver is BLANK? I've tried several suggestions from the forum but it still doesn't work.
    Have I missed something or is it quite possibly just a dud unit that I have to take back.
    thanks for all suggestions and ideas...
    sony

    OK, let's see, you have a device that is still under warranty. You properly installed said device. You put batteries in the remote but it does not work no matter what you try. It seems to me that you have only one option and you mentioned it in the penultimate sentence in your post.
    Hope it's not a long dri've.:smileyvery-happy:
    Richard
    Message Edited by sf3454 on 03-3-2005 03:28 AM

  • Remote control not working on Touchsmart 610-1030uk

    Had been working fine for long time. Now out of warranty. Battery fine. Indicator on remote and on PC (white LED on front panel) both show IR is working. Mouse and keyboard still work fine. I have tried uninstalling and reinstalling drivers for Microsoft eHome infrared transceiver but still can't get the machine to respond to remote control. 
    Any thoughts?
    This question was solved.
    View Solution.

    Hello frrw. Sorry to waste your time. I changed the batteries and it works fine. It seems the red LED on the remote and the white LED on the PC that flashes when I press a button on the remote do not mean that the batteries are strong enough. 
    Meanwhile I have that recurring problem with blu-ray players. I will post a new question and maybe you can help. 
    Many thanks. 

  • BT Vision Box and Remote Control not working prope...

    Hi,
    Can anybody help me please?
    I have a black BT Vision Box. The remote control had increasingly been sticking so tonight I just turned the power off tonight, left it off for 20 seconds and turned it back on.
    It seemed to turn back on and reboot itself normally, it took the amount of time it normally does on a couple of occasions when it froze a few months back. However since I rebooted it approximately 3 hours ago it has been turning itself off and rebooting itself every 10 minutes or so. On one occasion when I turned it off on the front of the machine and left it for a few minutes, it turned itself on and started rebooting itself again. 
    The remote control is worse than when it was sticking, now there is a delay of up to 30 seconds after I press a button. Sometimes it does not work at all, when that happens it just becomes stuck and eventually reboots itself.
    So far I have tried turning it off and on again, I have also tried rebooting the internet connection (which is working fine). I have tried pressing the off button on the actual box for 10 seconds and resetting it that way. I have put new batteries in the remote. Nothing has worked. If anyone can help me that would be great.
    Solved!
    Go to Solution.

    Hi, 
    Unfortunately I can't get that far now.
    I turned all TV related systems off last night in an effort to see if it would work properly today.
    I came home from work and turned everything on. The system boots itself up until it gets to a grey screen that says "Nearly there..." with the BT logo in the bottom right corner. It stays like that for approximately one minute. Then it turns itself off and starts rebooting itself again. 
    I have tried pressing the on/off button on the front of the box and holding it in for 10 secs or so until the box turns itself off and reboots but the effect is still the same as above. 
    Do you have any other suggestions pleaase, aside from throwing it in the bin?

  • Win2k8 Remote Control Not Working With SRSS 4.2 + SRWC 2.2

    Hi there.
    I have an install of Windows Server 2008 (32bit) with SRSS 4.2 & SRWC 2.2 setup. I was previously on SRSS 4.1 & SRWC 2.1 and having the same issue I am having now, which to me tells me this problem is unresolved or i'm being a total muppet. (hopefully not the last one)
    Windows Terminal Server environments has this awesome remote control feature where you can login to an RDP session which is already active and take control of the session while the end user is still logged in.With Server 2003 this works perfectly fine- it's brilliant. WIth 2008 it is a nightmare. It works for a split second and then closes off. The end users session also gets locked out (not logged out) and they have to put their windows credentials in to carry on working again.
    Now... I can remote control users who are logging in via Remote Desktop on Windows XP/Vista etc.. but I can't with the Sun Ray Sessions. Does the SRWC 2.2 fully compatible with RDP 6.1 or is there any information anyone can give me to point me in the right direction of resolving this issue, like I said.. Win 2k3- Works like a dream....
    Any help would be greatly appreciated.
    Regards
    - Joe.

    I just realised I hadn't posted the logs from SRSS Server with the issues. I have just tried on another WIN2K8 Server which wasn't configured by myself or my company and the same symptoms occurred. See logs below:
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4095]: [ID 702911 user.notice] /opt/SUNWuttsc/bin/uttsc[104]: 4116 Abort
    Oct 1 10:58:06 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4117]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4123]: [ID 702911 user.error] /opt/SUNWuttsc/bin/uttsc exited with error code 134 - exiting
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcrit: [ID 702911 user.notice] Info: critical application uttsc (pid=3902) exited with non zero status: 134
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 422571 user.info] Info: a critical application has exited.
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 126805 user.info] Terminating Kiosk Primary Session ( pid=3902 )
    Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 308018 user.info] kioskcritd stopped
    Oct 1 10:58:07 ESL-SOLARIS-SPARE utauthd: [ID 794400 user.info] SessionManager0 NOTICE: EMPTY: ACTIVE session
    Oct 1 10:58:15 ESL-SOLARIS-SPARE kiosk:utkioskconfig:refresh[4381]: [ID 702911 user.info] Enabled Kiosk Mode for display ':2'
    Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 118685 user.info] pam_sunray_amgh::[DPY=2] AMGH_SUMMARY: token=pseudo.00144fb78760, username=, AMGH_Done?=NO(Local Session), Details=AMGH is not configured., AMGH_Target=*NONE*
    Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 976841 user.info] pam_kiosk: pam_sm_authenticate: Initiating Kiosk session with user utku2
    Oct 1 10:58:15 ESL-SOLARIS-SPARE kioskcritd[4420]: [ID 190395 user.info] kioskcritd started
    Oct 1 10:58:57 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4612]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
    Anyone able to help me out?

  • Will remote control earphones work with the nano 5th gen?

    I've been trying to figure out if the remote control earphones will work with the 5th generation nano. It doesn't look like it comes with it, which is very sad, so I'm wondering if it would be worth it to buy it separately. Does anyone know if you can still use it to change songs and volume etc. on the nano? Please help!

    Good to know! Thank you very much

  • Car Bluetooth Steering Controls Not Working with iOS7

    Hi - I have 2013 RAV4. The a steering controls stopped working after updating to iOS 7.
    I can't switch to next song or previous song which i was able to do with iOS6.  Any suggestions how to fix this?

    There are some other discussions on loss of lock screen and control center music controls.
    https://discussions.apple.com/message/23063432#23063432
    https://discussions.apple.com/message/23042786#23042786
    https://discussions.apple.com/message/23071045#23071045
    I believe it is the same issue, which would indicate that it is an issue with the phone, nothing to do with the car/stereo/speakers/etc.
    When I lose Bluetooth control I also lose lock screen (and control center) controls.  Other controls work, but no play, pause, skip forward/back, and of course no song resume on reconnection.  A hard phone reset or power cycle fixes it every time, I never have to mess with the car.  However, the issue re-occurs about every 2-4 days and I have to reset the phone again to get control back.  Does everyone else lose lock screen control at the same time as BT?
    It may be a hardware issue.  I have a 4S.  What phone models are exibiting the BT issue?

  • XFI-64 Bit Driver, remote control not work

    I have just installed the 64Bit drivers for my X-fi Fatality. The sound works however the 'sound console' that plugs into the dri've bay at the front of my pc does not seem to be working. I press start on the remote control and nothing happens. The X-fi volume icon does not appear in the system tray. When I boot up the 32 bit version of windows all is well and i can use the remote control and all of its functions. Can anyone help as this is now very frustrating.

    Originally Posted by MiLoCzE
    Hi men, if you will use remote control, you must install ECUP_PCVTAPP_LB_3_40_21 . :-)
    What is " ECUP_PCVTAPP_LB_3_40_21 " ?
    I searched on the internet and all I could find about it is that it's a virus? Can you tell me something more about that file ?
    http://www.pc-face.com/exe-file-erro...exe-fix-22694/

  • Remote control stops working after a few days

    NW 6 SP3
    ZFD 3.2 SP2
    After importing workstations, remote control works fine. After a few
    days, remote ping might work but NOT remote control. Sometimes even remote ping errors out with the message that the "REMOTE MANAGEMENT
    AGENT
    IS NOT RUNNING"(when it appears it is). If I stop and start the
    "novell
    wuser agent" service, then I can usually remote control the
    workstation
    again. Occasionally, however, I get the message "The Remote
    Management
    agent was unable to locate the workstation in NDS". At which point I
    have
    to delete the workstation object and re-import the workstation to be
    able
    to remote control it again.
    Any help is appreciated.
    Jeff

    > [email protected]
    >
    > >
    > > The login script is running wsreg32.exe with the /s parameter
    > > pointing to the server servicing the import services.
    >
    > Is there a reason you are using this?
    > instead of DNS, hosts, or registry?
    >
    > As I am wondering if maybe at times the workstation manager tries to
    > registr, but can't find the server, even the wsreg is running.
    > Normally onces the workstation has registered it doesn't need the
    > address again, but if for whatever reason cannot find it's
    workstation
    > object it will need to resolve the import services.
    >
    > --
    > Jared L Jennings, CNE
    > Novell Support Forums SysOp.
    > http://support.novell.com/forums/faq_nntp.html
    >
    > Posting with XanaNews Reader 1.15.8.2
    > Geek by Nature, NetWare by Choice.
    I have a different server for each site(city) hosting the import
    services. There is only one variable allowed in DNS so all sites
    would
    try to get services and register to the same server.
    Using the container login script for each site to set the /s parameter
    was
    easier than changing the registry setting for each
    workstation...especially if that server changed. This way I would
    only
    have to change it one place.
    If the workstation has already been registered and imported AND I can
    remote control it, does it NEED to find the import server again if it
    hasn't been rebooted since the last time I remote controlled it?
    Thanks, jg

  • SCCM Remote Control Feature Working

    Hi,
    Would like to get some insight into the working of SCCM 2012 remote features.
    When an admin starts a session (i.e. right click on machine > Start > Remote control). How is the connection made. I know this uses TCP 2701 port but what I mean is,
    If the standalone primary server is hosted in US and the UK site admin starts a remote control session for a machine present in UK locally. Does it makes a connection  from the admin's machine to the local machine or if the connection is established
    by first connecting from UK to Primary server and then from primary to the local UK machine ?
    Also, in another scenario, if admin is using SCCM console which is published on CITRIX. How will the connection proceed, i.e. would it be from admin machine to citrix farm, then to primary server and all the way back to the local UK machine.
    Thanks

    Thanks Torsten,
    What
    i need to make sure if i am not confusing it,  there would be a LAN connection if the machine is in the same region as I specified for example? for the scenario where the console is locally installed ?
    OK. We have majority of machines using CITRIX to use SCCM console, going by your answer, each of the machine will hit the CITRIX server and make a connection from there. 

Maybe you are looking for