Bluetooth stopped working after update to PR1.3

After updating my N9 to PR1.3 the bluetooth stopped working. Trying to connect it to my laptop or other phone is unsuccessful, only get "Transfer failed" message. Anyone has this problem, too?

@RSmaster
PR1.3 still transfers OK to my Mac, although always takes longer to go through than from Symbian device!
Happy to have helped forum with a Support Ratio = 42.5

Similar Messages

  • Bluetooth stopped working after updating to iOS 6.1

    Yesterday I update the software on my iPhone 4 to iOS 6.1 and after starting back up it would not find my bluetooth headset (that I've used for the last year).  It will not find any bluetooth devices.  Previously, it would locate my headset, iPad, and iMac but now it lists them but will not connect and only shows a continuous search.  The bluetooth icon is gray in color. 
    I've turned the phone off and on several times, and also done a hard reset twice - the results have been negative.

    Try going into setting> General> Reset> Reset Network setting and if that does not work try reset all settings.

  • Wifi iPad 3 charger stopped working after updating to iOS 6, help!

    Wifi iPad 3 charger stopped working after updating to iOS 6.  The little iPhone charger charges it very very slowly, but the charger gets really hot after a while.  I restored it and everything works but the charger.  It's only a few months old, should I try a new iPad wall charger block?

    Hi,
    I did this after reading the forums and it made no difference. it has actually charged from 14% to 67% but thats taken over 12 hours.
    Will monitor it and if no joy will go to a apple store
    Thanks

  • Earpiece stopped working after updating to 5.0.1.

    It worked fine the night before.  Then it stopped working after updating to 5.0.1.  I can only hear calls on speaker.  Did anyone else have this problem.  I have tried all the fixes, restart, reboot, restore.  No debris in the headphone jack, and when volume is turned up or down it doesn't show headphones on the screen.  Nothing covering the earpiece.  Tried to blow out headphone jack with compressed air.  I'm thinking it is a glitch in the software.  Using Iphone 4 on Verizon.  Any thoughts or ideas?

    you can try reading the posts listed to your right in the "More Like This" box or by searching this forum.

  • HT201371 Touch ID stopped working after updating to IOS 7.1.

    Good morning to all,
    My touch ID stopped working after updating to IOS 7.1.
    It was working perfectly until the update and then it stopped recognizing my prints
    I've reset the phone and deleted my fingerprints and now I can't even add a fingerprint again.
    I am sure this is not a hardware problem since the phone was working perfectly before the update and it didn't fall nor anything similar.
    Also the sensor is clean as well as my fingers.

    Same problem... I think we all should let Apple know of this issue. http://www.apple.com/feedback/ tell them the probelm. So when they get too many complains they will surely fix it ASAP with a software update.

  • My Plug in "Free Download Manager" stopped working after update

    == Issue
    ==
    I have another kind of problem with Firefox
    == Description
    ==
    My Plug in = "Free Download Manager" stopped working after I updated FIrefox !
    It worked fine previously ! What did I do wrong ??
    **** Also I've forgotten my User name, but Firefox says that my email is registered already
    I was on some other Internet provider; and have been a PC user since 1987 ! I am a Retired Network Administrator for both Microsoft NT4 & Novell 4.x Networking; and a former IS Dept. Tech' for an Orlando, FL Corp' that had over 500 PC's;
    both Lap & Desk Top for some 3 1/2 yrs.
    ***** I CONSTANTLY RECOMMEND FIREFOX TO EVERYONE THAT IS EITHER MY CLIENT -- OR ANY OTHER CASUAL CONTACT *****
    ***** In fact I suggested your Browser to 3 people Today; Wed. the 14th of July 2010 *****
    Respectfully;
    Raymond E Bachelor
    aka "New System Services"
    <blockquote>Removed personal info. Please don't out yourself, or post personal info on forums. thanks! -T </blockquote>
    == This happened
    ==
    Every time Firefox opened
    == I updated Firefox to the Newest Version !
    ==
    == Troubleshooting information
    ==
    PLEASE !!!!
    SEND ME MY LOGIN INFO I have an active email entry; but I've lost track of my Username over the years !
    == Firefox version
    ==
    3.6.6
    == Operating system
    ==
    Windows XP
    == User Agent
    ==
    Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2.6) Gecko/20100625 Firefox/3.6.6
    == Plugins installed
    ==
    *-Shockwave Flash 10.1 r53
    *Adobe Acrobat Plug-In Version 7.00 for Netscape
    *Office Plugin for Netscape Navigator
    *np-mswmp
    *getplusplusadobe16263
    *Default Plug-in
    *Delivery Network Acceleration by BitTorrent™
    *Windows Presentation Foundation (WPF) plug-in for Mozilla browsers
    *Npdsplay dll
    *DRM Store Netscape Plugin
    *DRM Netscape Network Object

    I hate it when updates break things instead of fixing them. Can't Mozilla leave well enough alone? At the very least, each new release should be tested so it works with ALL PREVIOUS extensions!
    Wait till you "update" to firefox 4 and EVERYthing breaks, including the buttons that come with it. There is no arrow next to the dropdown button, right clicking the tab bar doesn't bring up the correct menu, but one as though it were the menu bar (which is missing) and the information bar is missing. True, it's fast, but you'll spend weeks getting it to work properly.

  • Why do some apps stop working after update to iOS 6?

    I notice one of my apps stopped working after the iOS 6 update, in particular Uno HD, which I paid $5 for.  Why did this happen?

    I had solved the problem by installing the free app, which seemed to reset something, then I deleted the free app, and the paid version continued to work until the next day.  I was going to show one of my friends the game, and then it once again would not open- the same problem was back, as soon as I went to open it, it crashed back to the desktop without opening the game.  I had to re-install the free version again, and for a while, neither version would work, but then after a while, it started working again.  I guess I have to leave the free app installed or I won't be able to use the paid version of Uno.
    EDIT
    Just checked again, took the Uno app out of resident memory by double-pushing the home button and holding the app icon til it starts to shake, and then hit the minus symbol, which deletes it out of resident memory.
    Went to open it again, and it of course crashed back to the desktop again.  So there is some issue with it that is making it unstable.
    I have to keep pushing on either one of  the app icons continuously until one of them starts, and then the other one will start.
    Gameloft needs to do an update.
    Message was edited by: Sonic Bodhi

  • The inspector stopped working after update

    The inspector stopped working after an update. When I click on the inspector button it says "An unexpected error has occured. Please quit and reopen Keynote." Quitting and reopening Keynote does not fix the problem. Inspector does not work in Pages either (it doesn't do anything when I click on it), but it does work in Numbers. I also am having problems opening files created in Numbers before the update.

    Hi jeau300!
    Here is an article that can give you some tips about using your computer with your external monitor in closed clamshell mode:
    Mac notebooks: How to use your computer in closed clamshell (display closed) mode with an external display
    http://support.apple.com/kb/ht3131
    How to disconnect your Mac notebook from the display after use:
    For best results it is recommend that you put your computer to sleep before disconnecting your display.
    Note: Some DVI and Mini DisplayPort displays—including Apple's aluminum-framed DVI displays and the 24-inch and 27-inch LED Cinema Displays—can be unplugged without putting the computer to sleep. If you aren't sure whether your display supports this feature, put your computer to sleep before unplugging the display.
    Take care, and thanks for visiting the Apple Support Communities.
    Cheers,
    Braden

  • Send Link and Mail To are stop working after update to FF v.13 on WinXP

    Send Link and Mail To where stopped working after upgrade to FF13 on win XP. I'd appreciate any suggestions.
    Thank you in advance

    Can you check to see whether your mailto setting got changed?
    orange Firefox button ''or'' classic Tools menu > Options > Applications
    In the Search box above the list, type or paste '''mailto''' and pause while Firefox filters the list. On the right side, you can select your mail application. Unless it's missing. Are you able to establish the connection?

  • Audi AMI bluetooth stopped working after 4.2.1 update

    Don't think there is a fix for this, but so others don't run into the same issue...
    Seems the latest OS update limits the bluetooth connectivity, i can make calls (iPhone 4) but the bluetooth connection drops after about 3secs, and carries over to the phone. I've tried deleting all parings on both sides etc, but haven't found a solution as yet. everything was fine on previous version, and to some extent it does work still just for 3 secs only.
    let me know if anyones found a fix to this, and before i get lots of chimes in about getting the car bluetooth upgraded, i understand that approach, however the os change has stopped this not the car, apple created the issue, they should address, or test such that they can pre-warn etc.

    Hi there,
    I have had exactly the same problem on my 2009 Audi A4 with my iPhone 3G which I have just upgraded to 4.2.1, I have tried re-pairing the phone and also doing a factory refresh on my iPhone. If you find a fix, I would be interested in knowing what it is.
    All the best,
    Rich

  • Bluetooth stopped working after 7.1.1 update

    My iphone 5s stopped pairing in my truck, pretty sure after the 7.1.1 update, anyone have a fix?

    Same problem here. no wifi or bluetooth after updating to iOS 7.1.1
    Off to genius bar tomorrow. restore via itunes didnt work

  • Bluetooth stops working after OS X update on mac mini

    Just installed the OS X 10.8.5 on my Mac Mini late 2012 model and after the restart the bluetooth was not available. I had to find a USB Keyboard and mouse to be able to log on to my computer and use it. Does anyone know how to repair this. This must be a fault from Apples update and Apple should find a solution or bring out a fix on this update. Any ideas

    Try resetting the SMC
    Intel-based Macs: Resetting the System Management Controller (SMC)
    I had no problem on my 2012 Mni after updating.

  • Bluetooth stopped working after 7.1 update

    After I updated to IOS 7.1 my phone cannot connect to any bluetooth devices. Car, Headset, Mac. it keeps seeking but it is not able to locate any devices.

    Same problem here. no wifi or bluetooth after updating to iOS 7.1.1
    Off to genius bar tomorrow. restore via itunes didnt work

  • Dell XPS 15 l502x mini-Display Port stopped working after update.

    After the updates on the 11-10-2014 my mini-display port (which worked great previously and is part of the Intel Graphics) stopped working.
    Am running Arch 64bit with Slim + E19
    The symptoms are:
    1. Detects monitor from the laptop and xrandr throws no errors
    2. Enlightenment thinks the screen is connected and it appears in the screen setup as on.
    3. The monitor no longer recognizes that there is a laptop plugged in and just stays off...
    kernel.log
    Oct 13 10:10:19 localhost kernel: [drm:cpt_set_fifo_underrun_reporting] *ERROR* uncleared pch fifo underrun on pch transcoder B
    Oct 13 10:10:19 localhost kernel: [drm:cpt_serr_int_handler] *ERROR* PCH transcoder B FIFO underrun
    Oct 13 14:09:35 localhost kernel: [drm] Wrong MCH_SSKPD value: 0x16040307
    Oct 13 14:09:35 localhost kernel: [drm] This can cause pipe underruns and display issues.
    Oct 13 14:09:35 localhost kernel: [drm] Please upgrade your BIOS to fix this.  (Will look for an update...)
    lspci | grep Intel | grep VGA
    00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
    Here are the packages that I think I may have to swap around...
    [2014-10-11 19:16] [PACMAN] removed ati-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] removed intel-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] removed nouveau-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] removed svga-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] removed lib32-intel-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] removed lib32-nouveau-dri (10.2.8-1)
    [2014-10-11 19:16] [PACMAN] upgraded apache-ant (1.9.4-2 -> 1.9.4-3)
    [2014-10-11 19:16] [PACMAN] upgraded libdrm (2.4.56-1 -> 2.4.58-1)
    [2014-10-11 19:16] [PACMAN] installed mesa-dri (10.3.0-3)
    [2014-10-11 19:16] [PACMAN] upgraded wayland (1.5.0-1 -> 1.6.0-1)
    [2014-10-11 19:16] [PACMAN] upgraded mesa (10.2.8-1 -> 10.3.0-3)
    [2014-10-11 19:16] [PACMAN] upgraded mesa-libgl (10.2.8-1 -> 10.3.0-3)
    [2014-10-11 19:16] [PACMAN] upgraded libva (1.3.1-2 -> 1.4.0-1)
    [2014-10-11 19:20] [PACMAN] upgraded linux-lts (3.14.19-1 -> 3.14.20-1)
    [2014-10-11 19:27] [PACMAN] upgraded xf86-video-ati (1:7.4.0-3 -> 1:7.5.0-1)
    [2014-10-11 19:27] [PACMAN] upgraded xf86-video-intel (2.99.916-2 -> 2.99.916-3)
    As far as I can see my options are to try and roll back via pacman -U in my /var/cache... or to figure out how to make my Nvidia HDMI output work using Synergy...
    I suspect this is some type of driver regression (kernel/mesa/xorg) but am not sure as I have not seen much information about this issue online.
    Unless someone has a better idea... when I get time to try to resolve the issue I will update this post.
    Ok I missed this from dmesg:
    [11671.333426] WARNING: CPU: 0 PID: 486 at drivers/gpu/drm/i915/intel_dp.c:137 intel_dp_max_link_bw.isra.9+0x3e/0xa0 [i915]()
    [11671.333428] invalid max DP link bw val 0, using 1.62Gbps
    [11671.333430] Modules linked in: ctr ccm bnep ipt_REJECT xt_conntrack iptable_filter xt_CHECKSUM xt_tcpudp iptable_mangle ipt_MASQUERADE iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core fuse v4l2_common ecb videodev media btusb bluetooth 6lowpan_iphc coretemp hwmon intel_rapl x86_pkg_temp_thermal intel_powerclamp joydev mousedev snd_hda_codec_hdmi kvm_intel arc4 snd_hda_codec_realtek snd_hda_codec_generic kvm iwldvm snd_hda_intel snd_hda_controller crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel cryptd snd_hda_codec r8169 iwlwifi snd_hwdep dell_wmi snd_pcm sparse_keymap iTCO_wdt snd_timer snd mii iTCO_vendor_support dell_laptop microcode pcspkr dcdbas dell_smo8800 psmouse serio_raw
    [11671.333467]  thermal soundcore i2c_i801 shpchp evdev mac_hid mei_me mei lpc_ich wmi processor ac battery pci_stub vboxpci(O) vboxnetflt(O) vboxnetadp(O) vboxdrv(O) udlfb syscopyarea sysfillrect sysimgblt fb_sys_fops tun nfs lockd sunrpc fscache vhba(O) bridge stp llc brcmsmac cordic brcmutil led_class bcma mac80211 cfg80211 rfkill bbswitch(O) ext4 crc16 mbcache jbd2 sd_mod sr_mod crc_t10dif cdrom crct10dif_common atkbd libps2 ahci libahci ehci_pci libata xhci_hcd ehci_hcd scsi_mod usbcore usb_common i8042 serio i915 button intel_gtt i2c_algo_bit video drm_kms_helper drm i2c_core
    [11671.333506] CPU: 0 PID: 486 Comm: Xorg.bin Tainted: G        W  O  3.16.4-1-ARCH #1
    [11671.333509] Hardware name: Dell Inc.          Dell System XPS L502X/0YR8NN, BIOS A04 03/25/2011
    [11671.333511]  0000000000000000 00000000c0982604 ffff8800b2b4fa80 ffffffff8152ba1c
    [11671.333515]  ffff8800b2b4fac8 ffff8800b2b4fab8 ffffffff8106e45d ffff880037c92000
    [11671.333518]  0000000000000000 0000000000000004 ffff88014e2d8c00 ffff8801b5a2f800
    [11671.333521] Call Trace:
    [11671.333528]  [<ffffffff8152ba1c>] dump_stack+0x4d/0x6f
    [11671.333534]  [<ffffffff8106e45d>] warn_slowpath_common+0x7d/0xa0
    [11671.333537]  [<ffffffff8106e4dc>] warn_slowpath_fmt+0x5c/0x80
    [11671.333553]  [<ffffffffa00f543e>] intel_dp_max_link_bw.isra.9+0x3e/0xa0 [i915]
    [11671.333566]  [<ffffffffa00f5539>] intel_dp_compute_config+0x99/0x660 [i915]
    [11671.333579]  [<ffffffffa00da214>] __intel_set_mode+0xb14/0x1670 [i915]
    [11671.333608]  [<ffffffffa00dd4e6>] intel_set_mode+0x16/0x30 [i915]
    [11671.333638]  [<ffffffffa00de623>] intel_crtc_set_config+0xa83/0xdd0 [i915]
    [11671.333666]  [<ffffffffa0025fa1>] drm_mode_set_config_internal+0x61/0xe0 [drm]
    [11671.333690]  [<ffffffffa002984b>] drm_mode_setcrtc+0x2ab/0x5b0 [drm]
    [11671.333712]  [<ffffffffa0019b9f>] drm_ioctl+0x1df/0x680 [drm]
    [11671.333728]  [<ffffffff811d4db0>] do_vfs_ioctl+0x2d0/0x4b0
    [11671.333737]  [<ffffffff811df4ee>] ? __fget+0x6e/0xb0
    [11671.333745]  [<ffffffff811d5011>] SyS_ioctl+0x81/0xa0
    [11671.333753]  [<ffffffff815317a9>] system_call_fastpath+0x16/0x1b
    [11671.333758] ---[ end trace 64be8044e26ca3c5 ]---
    Last edited by scmurcott (2014-10-13 19:12:07)

    So I downgraded those packages and the kernel with no luck.
    I tried to get the HDMI working via Synergy... and failed
    I then tested the Display Port on Windows and it did not work there either - exhibiting the same symptoms as Linux - the OS sees the monitor but no data was transferred.
    So I ended up using one of my Display Link monitors at work... the USB monitors were ok, just an irritation with a flickering mouse.
    I hope it is the miniDP>HDMI adapter and not the port... very frustrated by this problem.
    I hope to test another adapter soon.
    I think as nobody else is experiencing this issue that it may well be hardware/firmware related.
    Hope there is a happy end to this post but not feeling so positive right now.

  • Yoga 13 touch screen stopped working after update KB3000850, please help!

    Hi, my Yoga 13 touch screen has been working fine until yesterday. The laptop came with Windows 8, and last year I upgraded to Windows 8.1 without issue. Yesterday, I installed optional update KB3000850 from Windows Update, and immediately the touch screen stopped working. I have tried the following methods, all without success:
    * Uninstall KB3000850 from Windows Update
    * Use Windows Restore to restore to the point before yesterday
    * Re-install Intel Chipset Driver from Lenovo official driver page
    * In Device Manager, uncheck all the "allow system to turn off to save power" options for the USB input devices under Human Interface Devices then restart
    * Two-button shutdown and restart
    * Install Lenovo Driver Manager and let it check for new drivers
    * Download Cando multi touch panel driver (Note: I could not install the driver because all I got was a .cab file which does not allow me to install)
    As of now my touch screen is still not working. Computer Information page from Settings shows that there is no touch or pen device for my screen.
    Can anybody help me with this? Thanks!

    Very true, this has been a known problem since the first day Lenovo released the Yoga 13.
    I need to send Lenovo a bill for my time spent rebooting.  So far i am on my 8th reboot.  In the past, around 5 reboots after winddows update would work.  This time... who knows.
    Of course it always happens when you have a deadline.
    Please post back if you have found a better soultion than system restore.
    Thanks for posting this issue.  More users need to bring this to Lenovo's attention.

Maybe you are looking for