Bluetooth voice quality - LG Cosmos 2

Frustrated and wondering where to start.  New car (Honda CR-V) and new phone (Cosmos 2.)  Bought the phone solely because my original (very old) phone wouldn't "pair" with the new car's bluetooth.  The Cosmos has gotten past that, makes & receives calls, phonebook has been imported and everything works fine except for one (major) thing:  The outbound (phone user's) voice quality is horrible.  All garbled, almost not understandable to anyone on the other end.  Inbound voice (played through the car's speakers) is fine.  So where do I start?  I'm anticipating that Verizon will tell me it's a Honda problem and Honda will tell me it's a Verizon problem.  I'll almost bet on it.  Any solid, unbiased advice on what is actually likely to be the problem, and how to fix it?  Thanks.

You would test outbound voice quality using just the phone not Bluetooth from the same locations to determine if the problem is with the phone and Vzw service OR if you only experience the problem when connected by BlueTooth wireless and thus the built-in mic in the Honda.

Similar Messages

  • Bad Reception, Muffled Bluetooth Voice, Crazy Proximity Sensors

    I would like to start a new thread to summarize all major the problems of the iPhone 4. Apple has to either release a software update or just do a total recall for all iPhone 4 users. Consumers should NOT be responsible for the time they have wasted to troubleshoot the device, paying the restocking fee or buying a Bumper Case.
    1. Antenna: In spotty area mostly running 1900 MHz band, the iPhone 4 reception degrades until 1 to 0 bar when the hand or any conducting material has blocked the bottom left of the phone with a notch on the stainless steel antenna.
    2. *Muffled Bluetooth audio quality:* where the listener has no way to hear a clear voice at all beside a muffled voice with low volume when speaker is using a Bluetooth that is connected to the iPhone 4. It happens to various Bluetooth headsets on the market including the Jawbone, Jawbone Icon, Plantronics 925, Sony, Motorola, and more. The muffled sound does not occur consistently. Sometimes is clear, but most of the time bad.
    3. *Proximity Sensors:* Not sure if the sensor is located on top of the ear piece. During a phone call using the ear piece, people are experiencing trouble with the screen goes on and off and the face controlling the screen unintentionally which leads to hang up, mute, and other types of accidental operations.
    These are critical issues that affect normal phone calls and iPhone 4 has failed to achieve anyone of them.
    Message was edited by: squarejp

    espleyk wrote:
    Really sorry to burst into your discussion, but I can't find any way of asking a question.
    Like you, it's my first smartphone and I am really frustrated with it too. Am awaiting delivery of a new phone today due to its inability to connect to the internet or for me to get email.
    But today's frustration is this and it's a really urgent query that I'm hoping someone can help me with quickly before the delivery man arrives.
    Having spent all day Sunday getting my contacts sorted out, I'm nervous about losing them. So installed ovi suite this morning and apparently successfully to copy my contacts etc through content copier. It said it had saved them to
    C:\Users\Karen\AppData\Roaming\Nseries\ContentCopier\2009-07-23Nokia N97 (2).nbu. However when I went to look for the folder AppData, it doesn't exist and I can't find it anywhere.
    Any idea where it may have gone and what I can do to get my contacts onto my pc. I've tried going through the mass storage route on the phone, but then the folders that appear do not hold the contact details anywhere.
    I am desperate (in so many ways ;-)
    Any help gratefully received
    Technopigmy 
    to see the Appdata folder on your pc you need to Show Hidden files and folders.
    using windows XP (not sure about vista) goto My Computer. on the menu bar, select "Tools" then "Folder options", then "View". select the option that says "show hidden files and folders"
    Another way to get the contacts from your phone is using PC Suite. Select the "Contacts" function in pc suite.
    once this opens, highlight the contacts you want to copy and go to "File" and "export"
    here you can export your contacts as a text file or as a csv file for that you can open in Excel etc.
    Message Edited by foxmeister on 23-Jul-2009 12:53 PM
    If this Post is helpful. A click on the White Kudos star is always Appreciated
    Last Nokia: Nokia Lumia 800
    Current Phone: A Non Nokia Device
    Previous Phones:Don't Ask ;-)

  • Voice quality problems on iPhone 5s with IOS 7.02 on Verizon.I

    I have a brand new iPhone 5s with IOS 7.02 on Verizon.  Everything works great except when on talk on the phone the normal way.  When I do that, people tell me they can hardly hear me.  But, when I put them on the speaker phone, they can hear me very well.  Also, Voice Memos, and SIri all work just fine.  It is only when I talk on the phone the normal way (without the speakerphone on) that the voice quality I am transmitting is very low.  Does anyone know how to fix this?  Thanks very much.

    Apple helped me solve this problem.  They gave me a brand new iPhone 5s.  The were just great in their support.  It appears that my first iPhone 5s had a faulty "audio chip."  This is the chip that changes the frequency of your voice as you talk into the microphone; Apple explained that it is one frequency when talking on the phone, and another where using the speakerphone, and another when using Siri, and another when using voice memos, etc. You use the same 2 microphones for all of these applications (one at the bottom of the phone, and one my the camera lens), but the "audio chip" adjusts the freqency based on the applicaiton you are using.  So, on my first iPhone 5s, my "audio chip" was defective, so they gave me a new iPhone 5s, and it has been working just fine.  I had the most current IOS operating system on the original iPhone 5s with the faulty "audio chip," and on my new iPhone 5s which works great.  Hope this helps.  The technicians at Apple Customer Care and at the Apple Store are very aware of this problem with potentially defective "audio chips" in some of the iPhone 5s's.  Cheers, Clarence from Cleveland.

  • IPhone 4s - Battery issue and poor voice quality

    I had bought my iPhone in May this year. It was working fine till i think a week back battery started to drain quickly at 10% every hour. I have configured office exchange account for mail and accessing global exchange contacts, Google account as exchange for contact sync and iCloud. i dont keep any contacts on exchange, keep in Gmail only. Was Android user earlier.
    I read a lot of posts and tried all solutions such as turning off timezone service in location, turn off and delete all email accounts, kept manual sync for emails, ran the battery down till switch off and charging back to 100%, removed apps i doubted could be syncing data in background, turned off locaiton service totally, turned off calendar, turned calendar notifications, turned of iCloud reminder, notes but no effect. Wifi and Siri are also off.
    I notice today that I am getting small circle near operator name rather than E symbol (for edge)and at the same time voice quality of person on other end is bad too, can hear small cracking , clicking sounds, voice breaks. Otther person can hear me properly. I get back E symbol in some different place than my desk. I havent changed my desk so thats not a possibility either.
    Someone had suggested queued network thread with exchange can cause the issue so Installed System Activity Monitor app but it doesn't show battery graph or which process is taking CPU or network time. Moreover, it shows 4-5% less battery level than on top in disharging mode !!
    Used to get good stats of what is eating the battery in my old HTC Desire but iPhone doesn't offer such feature to diagnosis. Ideally should not be required if phone works as expected.
    What do I need to do to get battery life and voice quality back? I will try voice again at home just to rule out bad network at work.
    Thanks,
    Ashish

    Well, most of what you did is black magic, and has nothing to do with battery drain. But we have no way of knowing how your battery life is below what you think it should be. What are you using it for, what apps do you have, and how much Usage life do you get (settings/general/usage).

  • Is it a way to use bluetooth voice system in my volvo s80 with iPhone ?

    is it a way to use bluetooth voice system in my volvo s80 with iPhone ?
    Volvo system can not see iPhone, like my old phone.

    It's a pretty good idea - why not send a suggestion here:
    http://www.apple.com/feedback/appletv.html
    ....especially as AppleTV has no analogue audio out, and most non-Bluetooth wireless headphones would expect an analogue input (there are some expensive ones that handle optical, or the user coudl maybe use TV headphone/audio out, but Bluetooth audio might be handy for many.
    AC

  • Current Android 2.1 OS Not Compatible with Bluetooth Voice Activation

    After spending two frustrating days trying to make Bluetooth Voice Activation work with the HTC Incredible Android, I found out from HTC technical support that the Android 2.1 OS is not compatible with Bluetooth Voice Activation.  Supposedly changes to the operating system will correct the problem, but you're out of luck until then.....whenever 'then' is!  It appears that Verizon and HTC  have not choosen to include that information in their marketing material.  A bit irresponsible, especially if you live in a state that requires handsfree operation of your phone in an automobile.   

    It seems that Moto has a workaround in 2.1 on the Droid X:
    I was just at VZW store this morning looking at the Droid X (which is currently at 2.1), and specifically asked an employee about this and he showed that it's solved on the Droid X -- he paired his bluetooth and demo'd handsfree dialing it for me.
    Unfortunately, the Droid X is probably too large for me or my wife and the Droid Incredible doesn't have a solution for bluetooth handsfree dialing (yet).

  • Deteriorating Paul and Kate voice quality, Captivate 5

    I am working  on a project which involves importing a power point presentation ( 60 slides  with own Paul and Kate audio files total size of presentation 50 MB), and when I  publish the project it works fine but half way through the Paul and Kate voice  quality starts to deteriorate and becomes a slur.
    Publish  setting used:
    I would appreciate  any help in fixing this problem

    Moving this discussion to the Captivate forum.

  • First words are lost when using Bluetooth voice de...

    This happens with any Nokia Nxx or Exx when used with bluetooth HF device, like Nokia HF-300. Is there any solution to this problem? In practice you can hardly use any navigation with bluetooth voice. The delay itself is not a problem but the phone should wait 0.x seconds after opening the line to the HF device. It would be nice if you could configure this kind of delay to the phone.

    Is this the case when listening to the radio or music from the phone?
    I'd expect it to pick everything up when listening to music from  the phone as it's on the same channel (A2DP).
    But if you're getting all the nav guidance with a radio mute then that is a huge step forward.
    Usually the problem occurs when there is a delay for the mute of the radio followed by the streaming over mono channel.
    Message Edited by confiture on 18-May-2009 08:56 PM

  • Really freaky problem with mic voice quality on calls

    With my old headphones getting, well, too old, I decided to buy new ones, and so I did. The problem is, when I tried using them, my friends told me (while laughing non-stop) that it sounded like I was speaking from afar and with the typical headphones of fast food restaurants workers that make your voice sound weird.I thought it was the headphone's fault, so I changed them today, but the exact same thing happened. I thought maybe it was cuz my old ones worked on a USB connection, and the 2 new ones with a jack cable, but a friend told me it didn't make any sense and, furthermore, I tried calling him on Skype and he actually could hear me perfectly! Then I went to try again with my friends and, for them, it still sounded insanely weird as always (disclaimer: no, they are not pulling my leg). I disabled the automatic configuration of mic in audio configuration, played with the slider, whatever I could see in the options. I'm completely bewildered because I don't even know if what's happening is a problem, an incompatibility of my PC with jack headphones, or what's going on.I would appreciate any sort of insight.

        Hey there, Skymoose! I'm glad to see that you're managing your device. No, I can't say that clearing the cache would impact your voice quality. The cache is merely a temporary memory storage function. Do you use a headset of any kind with your device? If so, does this issue occur with and without the headset?
    DionM_VZW
    Follow us on Twitter www.twitter.com/vzwsupport

  • H323-Voice-Quality explanation

    I understand that the h323-voice-quality VSA conveys the calculated ICPIF factor, which is supposed to be a positive integer. However, on many occasions, this VSA contains the value "-1" or "h323-voice-quality=-1"(In fact, it appears in some examples of this very web site). What is the meaning in this case? Clearly, it can't be used but there must be some reasoning behind it that I'd like to know. Same goes for the value "0", which is unrealistic when codecs other than G.711 are being used, and for any ICPIF value over 50.

    The value should be in from 0 - 34 not -1.This should be calculated from the icpif for the call. Two caveats with
    this value. First is that it relies on rtcp (which for example our ip phones do not support). The second is that the call needs to be longer than 10 second in duration. If neither of these conditions are true, you should expect it not to be set; or as shown as -1.
    As a workaround try upgradig the IOS to the latest one.

  • 7921-CME Voice Quality Issue

    Hello,
    I am running into an issue at customer site which is going on for over 30 days.
    They have consistent voice quality issue with 7921 phones.Have checked their phone webpage and see that jitter value increases to 500 during issue. Sometimes I see tcpretransmissions too,
    They have QoS but that doesnt seem to help.
    I have even collected sniffer off wireless but not able to play due to wireless header.
    Have worked with TAC but they do not find any thing conclusive.Can anyone pls tell me what else can be done to analyse and fix the issue

    Is the issue with unicast RTP or with multicast (i.e. paging)?
    What AP platform and version are you using?
    1.2(1) for the 7921 was just released.
    1.2(1) Software
    http://tools.cisco.com/support/downloads/go/Model.x?mdfid=280808676&mdfLevel=Model&treeName=Voice%20and%20Unified%20Communications&modelName=Cisco%20Unified%20Wireless%20IP%20Phone%207921G&treeMdfId=278875240
    1.2(1) Release Notes
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/firmware/1_2_1/english/release/notes/7921_12.html
    Other than that ensure the deployment is inline with the 7921G Deployment Guide.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7921g/6_0/english/deployment/guide/7921dply.pdf

  • Tell me, is the 3GS a better phone than the 3G (how's the voice quality)?

    I'm likely to go with the 3GS when my current Verizon plan expires in a few months. As great as the iPhones are, I have some concern regarding phone voice quality. I have seen numerous online comments regarding the iPhone 3G having only mediocre voice quality.
    I would love to hear from new 3GS owners regarding their impressions of voice quality on their new phones. Also, if 3G owners would like to post comments on this issue I would be interested in this as well.
    I love the look, apps, etc etc. and am excited about moving up to an iPhone soon.

    I posted too early today before many had gotten their phones; now that it's evening and you have all had time to check it out, perhaps we can get some comments.

  • IPhone 5S Bluetooth call quality

    Problem: Degraded iPhone sound quality over Bluetooth when making voice call, FaceTime video/audio calls and Siri requests.
    I have been waiting for Apple to release a software update to fix this issue for some time. It appears to be a known issue however I have yet to see a response from Apple regarding the issue. Oddly, streaming music from my iPhone via Bluetooth delivers crystal clear sound. I suspect the iPhone uses a different Bluetooth profile for call streaming. Would someone be able to confirm this?
    It is worth noting that I am having this issue with every one of my Bluetooth devices. I have a Bluetooth-enabled Sony HiFi, Sony Bluetooth earphones and a Pioneer car stereo system with Parrot Bluetooth.
    Does anybody else have this issue? Would someone else with an iPhone 5S + Bluetooth devices be able to try and see if they share the exact same problem (that is degraded sound quality when making FaceTime video/audio calls and Siri requests over Blueooth)
    Thanks.

    Dabbaranks wrote:
    I have the distortion/crackling/popping with non-music, non-voice sounds (game sounds) on my Sony SBH80.  Is it a Mac thing?
    If your question is about your computer, you might be better off posting in the relevant Mac forum. This is the iPhone forum.
    Best of luck.

  • Crap BT handsfree voice quality using MEGA PLAYER 522BT

    It has been more than 2 months since I bought my MEGA PLAYER 522BT. Initially, I was thinking of using this as my handsfree, but th evoice quality is really some crap! Eversince then, I have been checking the MSI download page in hope for new FW to improve this. So far, only 1 FW was released, and it deals only the bugs in the audio player, not the Bluetooth module.
    That leads me to think that since mp3 players with 512MB onboard + ordinary BT handsfree costs more than this device, and the integration of both with the addition of SD/MMC card slot for this device will rack up the price quite a bit. But the price is very attractive when I bought it (consider it was an early launch at my place). So, the only logical thing I deduced from all this is: the BT module used in the device is CRAP!!!     
    I do hope I can find ways to improve it, but since it looks like it's a hardware issue, so not much hope there... Make no mistake. Using it as a pure basic music player is great, though. 
    If anyone could shed some light into this matter, any efforts are much appreciated.

    I am annoyed with my 522.
    At least 1 real 3.5mm head phone connector would have been nice.
    What I would like to see is MSI backing this unit up with a range of better earphones or headphones.
    It is impossible to buy any 2.5mm with a mic that work in the shops. Tiried my mda compact supplied phones. no joy.
    The unit works well, my complaints are
    1) An audio beep when incoming bluetooth would be nice, not just a fade.
    2) Bluetooth volume passed to the headset is low, I can hardly hear calls when in noisey stations , streets.
    Please MSI fix number 2.
    I have not had the echo problem.
    3) A better cover and belt clip/.arm clip. The one supplied is crap and is so tight the bluetooth button keeps engaging muting the sound.
    Intermitant crashes , but sound is not bad.
    Please MSI give me the chance to buy better phones. Ideally a 2.5mm fly lead , with a mic on for voice calls and a real 3.5mm headphone socket for my choice of phones.

  • IPhone 5 bad call voice quality

    Got the new iPhone 5 and have bad phone call quality. The recipient of the call seems to be able to hear me ok, but their voice either isn't there or drops out or sounds grainy like when you have bad cell reception. Many times, the calls have just not connected. I know that that my cell reception and the recipients cell reception were excellent. This has occured when calling other cell phones, land lines, and toll free numbers. Anyone else having this issue? Have an appointment at Apple tomorrow morning to see what they think.

    PROBLEM IDENTIFIED (..maybe)
    Update: Have not gone to the AT&T store yet, but was trying out some tests and think LTE is causing the problem. I am in an LTE capable area (Outside Washington DC). When I disabled LTE in the cellular settings, the phone calls sound clear. When I enabled the LTE in the settings, the majority of the time, I was having the bad voice call quality. Not sure if this would happen on Verizon network too, but could you try it out and see if you have the same results? If anyone else trys this test out, let me know your results.
    As an aside, My brother who lives in a non-LTE capable area has had no issues with call quality. Could be coincidence, but hope I have pinpointed the problem.

Maybe you are looking for

  • Lion - Issues with MacBook Pro Keyboards

    I have a 17" early 2008 MacBook Pro. It's Intel Core Duo 2. Since installing Lion, I seem to be having issues with its built-in keyboard, such as Command + C randomly not working on some apps, most recently Google Docs. But also with Bean and another

  • How to check whethere apps patch need downtime or not?

    hi, i am going to apply in Oracle 11i.how to that patch need down time or not? Plz help Thanks in advance

  • TS3694 How to downgrade from 4.2.1 to 3.1.2

    I have I phone 3g, Earlier i had software ver 3.1.2 where Camera and sound was ok. Now Its not working after upgrade Itunes         : 10.6.35 Software Ver   : 4.2.1 (8c148) serial number  : 87xxxxxy7h modemfirware   : 05.15.04 imei           : 01 202

  • Passing variable value with button or MC, that acts like a button

    Hi, I have a system.swf, that coordinates which MC should be loaded into container. I'm trying with IF statement... if (scene == "VALUE")) { load ... My question is, how can I pass a variable value from loaded swf to the system swf, where this value

  • Authentication and Debugging not working -- since Saturday, July 12

    Hi everyone, Since Saturday (July 12), the iTunes U launcher that my institution uses (a Moodle block) has ceased successfully authenticating users. From all the looking I've done, nothing has changed from our side, although I am having to do the inv