Bluetooth wont setup with iphon5

All,
I cant get my 2008 Toyota Land Cruiser to connect to my iphone5 via bluetooh. I had NO issues with my 4, and now I cant even get the devices to pair.
I am going through setup and trying to make it work, but I cant it to connect with the new phone.
Any advice would help.
Thanks!

WonderWoofy wrote:Still not enough information. We have now established that you have installed what should be the required software, you have bluetooth hardware, and you have started the service. If that is all you have done, then it really isn't even close to what that linked wiki page indicates.
I've tried with the tools listed in the wiki page. if this is not enough, you could tell me that could make some command, load modules, downloading drivers, etc..

Similar Messages

IPhone 4s bluetooth wont work with car

My Blackberry bold and iPhone 4 were absolutely fine with 3 different cars. I have just upgraded to the iPhone 4s and now the phone connects to the bluetooth but doesnt work properly. It rings and the screen shows that there is a call there, it even turns the radio off but the voice is coming out of the hadset. In previous versions i think you could select Audio Device 'in call' but you cant on the 4s. I have tried it in an Audi, a new Volvo and a BMW so i think that the car kits should be fairly up to date. Please help as i do lots of work miles during the day when on the phone.

i would try turning the bluetooth off and reconnect it and if that does not work reset your phone for it may be something wrong with it. if nothing else works you may have to bring it to the apple store, becuase the 4s you may have may have a bad bluetooth connector. hopes this helps

Bluetooth wont work with arch

I have two laptops (Samsung NP300EAX and Toshiba m645) both with bluetooth but I can not make it work
I've installed bluez and all bluez-* packages without success. install bluedevil on Samsung and gnome-control-center on Toshiba. I did everything indicates on https://wiki.archlinux.org/index.php/bluetooth.
- Install bluez
# pacman -S bluez bluez-utils bluez-firmware
- Install bluedevil ( I have KDE)
# pacman -S bluedevil
- enable bluetooth.service (start on boot) and start
# systemctl enable bluetooth && systemctl start bluetooth
can help me please
lspci on samsung
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.3 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM75 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
01:00.0 VGA compatible controller: NVIDIA Corporation GF119M [GeForce 610M] (rev a1)
02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
"dmesg | grep Bluetooth" on Samsung
[ 26.114129] Bluetooth: Core ver 2.16
[ 26.114150] Bluetooth: HCI device and connection manager initialized
[ 26.114158] Bluetooth: HCI socket layer initialized
[ 26.114161] Bluetooth: L2CAP socket layer initialized
[ 26.114167] Bluetooth: SCO socket layer initialized
[ 26.233024] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 26.233028] Bluetooth: BNEP filters: protocol multicast
[ 26.233037] Bluetooth: BNEP socket layer initialized
$ hcitool scan
Device is not available: No such device
both laptops have bluetooth on WIndows works <--
Last edited by rokemaster (2014-01-23 04:35:42)

WonderWoofy wrote:Still not enough information. We have now established that you have installed what should be the required software, you have bluetooth hardware, and you have started the service. If that is all you have done, then it really isn't even close to what that linked wiki page indicates.
I've tried with the tools listed in the wiki page. if this is not enough, you could tell me that could make some command, load modules, downloading drivers, etc..

Bluetooth wont synchronize with nokia 6131

OK so here it goes.. i have an imac running on os x.. when i try to browse my cellphone it just says "internal error".. Apparently i can send files from my cell to my imac but do nothing else.. when i click on pair, my phone turns off and restarts.. im not sure if its a problem with my mac..cause my bf has a macbook and my phone works fine with that one.. and i tried my dad's phone on mine ( motorola ) and it worked perfectly!.. also i've read that u go to sharing and check the box for bluetooth..and thats not my case, its already checked... thanks in advanced!:.

it was not answered.. didnt let me erase it

Bluetooth wont work with other phones

I have just purchased a Iphone 4s - the bluetooth does not recognise other phones but does recognise devices such as headphones etc.
Does anyone know why?
I want to transfer my contacts from my old phone
Can anyone advise how to do this. My old phone is a standard size sim card, not the same as the micro size card in the iphone.
Thanks

Can you send the contacts via Bluetooth to your computer, and then import them into Outlook for syncing with the iPhone via iTunes?
Alternatively, this app may help: http://itunes.apple.com/gb/app/inoki-transfer-nokia-data/id438619967?mt=8

My sprint sph-330 wont connect with my ipod 4g with bluetooth

my sprint sph-330 wont connect with my ipod 4g with bluetooth

That is because the iPod (and iPad and iPhone) do not have the necessary BT profiles to do that.
iOS: Supported Bluetooth profiles

IPhone 5 wont setup airplay via Bluetooth. iPhone 5s will successfully setup airplay via Bluetooth.

iPhone 5 wont setup airplay via Bluetooth. iPhone 5s will successfully setup airplay via Bluetooth.
Both iPhones are 7.1.

Is the Apple TV up to date?
Note: airplay still requires both to be on the same wifi network. The bluetooth feature is only for discovery, in place of using bonjour, and most useful for business/school networks.

Problem with bluetooth mouse setup at startup and no usb mouse functions

Today for the first time ever I got this screen for bluetooth mouse setup at startup. I've never seen this before and have no bluetooth devices. Very weird! It continues to search for a blue tooth mouse and won't let me do anything.The window says "Pairing with your bluetooth mouse.If the mouse is not found, make sure it is discoverable" My generic usb scroll mouse will not function and has always worked fine in the past. I tried plugging in the stock apple usb mouse also and this doesn't function either so there is no way to cancell this out. I've restarted several times and no luck ,can't login and no mouse functions. Just continues to search for a bluetooth mouse . This has me worried as this is recording studio computer and I have a session tomorrow . Any ideas how to get this to bypass this bluetooth window so I can startup and login and get my mouse functions back.
thanks,Craig
OS 10.4.10
G5 dual 2.5GHZ / 4GB ram

Solved it on my end... Hope you're not afraid of using some Unix programming...
I went into Unix mode (start up holding command key and s-key down). black screen with lines of white type pop up. (Means you are now in Unix mode). Give it a few minutes to check all the computer and when it no longer keeps adding any further info on screen type "fsck -fy", that is fsck space minus sign fy and without the quotation marks - exactly as shown inside quotation marks, and hit enter. It will run for several minutes detecting all that makes your computer work... I had in the final lines a message that read "file system modified". If this is the case than re-enter the fsck -fy command. Repeat this until one of the final lines will read "the volume appears to be OK". (I only had to do it twice to get to it). At this stage type "reboot". My mac restarted and I could log in without any sign of the annoying bleutooth mouse message. Hope it will work for you too!
Jo

Imac bluetooth not working with apple keyboard or magic mouse

Brand new imac won't connect to the bluetooth apple keyboard or magic mouse. I bought a usb keyboard and mouse to finish setup, but still cannot get them to connect. I tried going to system preferences, bluetooth, and trying to connect that way. I got halfway through the bluetooth keyboard setup until the connection failed. In the bluetooth setup assistant it cannot find any devices, despite them being in "discovery mode."
I tried connecting the mouse to my macbook pro and it worked fine, so I feel it is something wrong the the Imac's bluetooth.
Any guesses what might be going wrong here?

This fits with the observable results, however it does seem a little odd. The apple engineers coud have at least written the software to say something like, " I see an Iphone, but I can't do anything with it." Currently, it seem to behave like there is a problem with bluetooth connectivity. Not that the bluetooth is working fine, it just has nothing it can do with the two devices.
What you are trying to say has no sens. Check Apple TV manual and informations what bluetooth on this device is for and what options is giving to you before blaiming engineers for not making something straight.
Apple Tv 3rd (and 2nd) generation doesn't have a built-in storage and is more as a streaming device not syncing device. I suggest you read about Apple TV 3rd gen features and functionalyty and also about home sharing, airplay and airplay mirroring, apple remote app.
Also, check this information here: http://support.apple.com/kb/SP648
Wireless
Wi-Fi (802.11a/b/g/n)
Bluetooth support for Apple Wireless Keyboard (requires Apple TV software version 5.2 or later)

Wont open with 10.7

My iTunes wont open with 10.7. This is what it says
Process:         iTunes [1105]
Path:            /Applications/iTunes.app/Contents/MacOS/iTunes
Identifier:      iTunes
Version:         ??? (???)
Code Type:       X86-64 (Native)
Parent Process: bash [1102]
Date/Time:       2011-08-09 15:44:05.944 -0400
OS Version:      Mac OS X 10.7 (11A390)
Report Version: 8
Sleep/Wake UUID: B4FB8DBD-F5E9-46CD-8361-3C7D50B67129
Interval Since Last Report:          9675 sec
Crashes Since Last Report:           19
Per-App Crashes Since Last Report:   1
Anonymous UUID:                      F5D54A7A-2D13-4FD8-AE9E-383B07A62CB6
Crashed Thread: 0
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Application Specific Information:
dyld: launch, loading dependent libraries
@executable_path/../Frameworks/iPodUpdater.framework/Versions/A/iPodUpdater
Dyld Error Message:
Library not loaded: @executable_path/../Frameworks/iPodUpdater.framework/Versions/A/iPodUpdater
Referenced from: /Applications/iTunes.app/Contents/MacOS/iTunes
Reason: unsafe use of @executable_path in /Applications/iTunes.app/Contents/MacOS/iTunes with restricted binary
Binary Images:
       0x10cc09000 -        0x10db39fe7 com.apple.iTunes (10.4 - 10.4) <73B152D5-6088-0047-3C63-0A466B55E7EF> /Applications/iTunes.app/Contents/MacOS/iTunes
    0x7fff6c809000 -     0x7fff6c83e1ff dyld (195 - ???) <71093406-21CF-3DBE-A001-802259ED5300> /usr/lib/dyld
Model: MacBookPro5,5, BootROM MBP55.00AC.B03, 2 processors, Intel Core 2 Duo, 2.26 GHz, 2 GB, SMC 1.47f2
Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142323837334548312D4346382020
Memory Module: BANK 1/DIMM0, 1 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142323837334548312D4346382020
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 5.100.198.11 )
Bluetooth: Version 2.5.0b13, 2 service, 19 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: FUJITSU MJA2160BH FFS G1, 160.04 GB
Serial ATA Device: HL-DT-ST DVDRW GS23N
USB Device: Built-in iSight, apple_vendor_id, 0x8507, 0x24400000 / 2
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0x26500000 / 2
USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0236, 0x04600000 / 3
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x04500000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8213, 0x06110000 / 4

1. Try Right mouse click iTunes icon and select "Run as Administrator". Does it open now?
2. If not, check if this file APSDaemon.exe is the problem here.
Close your iTunes.
Press Ctrl-Alt-Del key and choose Task Manager. In the "Processes" Tab, select the file APSDaemon.exe and click End Prosses button, then close the task manager window.
Now open itunes and see if it is working?
If that works, to prevent having to do the same process everytime you restart Windows, go to. START button, type in
MSCONFIG
Hit ENTER
Click STARTUP Tab, Uncheck "Apple Push", click OK.
Restart Windows.
3. If step 2 fails, refer to following article to remove SC files:
http://support.apple.com/kb/TS2363
4. If step 3 fails, repair your Quicktime. START / CONTROL PANEL / PROGRAMS N FEATURES / hightlight QUICKTIME and click REPAIR.

My iPad 4 wont pair with my iPhone 5. Why?

My iPad 4 wont pair with my iPhone 5. Why?

What are you trying to do? If you are trying to use your
iPhone to provide internet access for your iPad, does your
wireless provider offer internet tethering and is your account
provisioned for it?
If you are trying to connect using bluetooth, this is not a feature of
iphone, iPad or iOS, never has been.
Bluetooth is supported for stereo headsets/speakers,
handsfree telephone devices/headsets, some keyboards,
some peer-to-peer apps from the app store and internet
tethering where provided by the carrier.
Other than this it will not connect to a phone/computer/device.
(thanks to ckuan for the wording)

I bought an iphone4s before my carrier put my sim in it i updated itunes now wont work with my sim

I bought an iphone4s before my carrier put my sim in it i updated itunes now wont work with my sim

Hello Aaron1658,
It sounds like you are unable to activate your phone with the SIM provided to you by your carrier. Try these steps in the following article to help you troubleshoot what it happening, named:
iPhone: Troubleshooting activation issues
http://support.apple.com/kb/ts3424
Symptoms
Your iPhone may display one of the following messages when you attempt to activate it:
"Your iPhone could not be activated because the activation server is temporarily unavailable."
"The SIM card inserted in this iPhone does not appear to be supported"
"The iPhone is not recognized and cannot be activated for service."
"iTunes was unable to verify your device."
Restart the iPhone.
Try another means of reaching the activation server and attempt to activate.
Try connecting to a known-good Wi-Fi network if you're unable to activate using a cellular data connection.
Try connecting to iTunes if you're unable to activate using Wi-Fi.
Restore the iPhone.
If you receive an alert message when you attempt to activate your iPhone, try to place the iPhone in recovery mode and perform a restore. If you're still unable to complete the setup assistant due to an activation error, contact Apple for assistance.
If this is not what you are referring to, would you provide some more information about what is happening? Any error messages, prompts, etc.?
Thank you for using Apple Support Communities.
All the very best,
Sterling

External isight wont work with imac g4

Hello,
I recently purchased a second hand isight camera using ebay.
I have an older imac g4 and the isight wont work with it at all.
I have scoured the forums on this topic and looked through all of EZ Jim's suggestions but I think my problem is a little bit different.
I'll explain exactly what happens and my troubleshooting so far...
The imac G4 is powered off, I plug in the external isight via firewire 400
The imac boots up into leopard 10.5.8 (using leopard assist)
In system profiler the isight is listed under the firewire tab.
( I can post system profiler info on this if its needed)
When I turn on the camera ichat launches, but then in the video tab it says no camera is connected.
Photobooth just has the no camera sign, but interestingly when ichat is opened photobooth says "camera off"
sometimes photobooth even lets me click the photo button, it counts down but then it doesnt take a picture... obviously!
Skype doesnt work.
I have an imac 24" running snow leopard 10.6.6 .... that also detects the camera but it won't work with any application such as skype or ichat.
I have tried (on my G4) unplugging my usb bluetooth module but nothing changes.
My G4 is connected via ethernet to an external router.
The firewire cable seems ok, I dont have any other firewire devices, but if it was a problem with the BUS or the cable then im guessing it wouldnt show in system profiler.
I am thinking the camera is probably damaged, but before I start a paypal enquiry I would like to see if it is just my computer or a setting i need to change.
(oh I used the application isight updater in core services but the install button is greyed out)
Any help would be amazing!!
Thanks!!!

Well, about all you can do would be to try a different and known good
FireWire cable, as a replacement for what may be a defective FW400
cable that came with the iSight camera. The cable can be defective
with one bad wire, yet sometimes appear available to the computer.
• How to Troubleshoot iSight (note external vs internal)
http://support.apple.com/kb/ht2090
• iMac G5 (iSight), & Intel-based iMac: Using External video camera:
http://support.apple.com/kb/HT2819
If you know of someone with an older Mac without a built-in iSight
camera, to test that one on, this may be an OK idea. Not sure if you
could get any traction by taking the camera to an Apple Specialist
and ask if they could check it out for you; that may also cost you.
{And since your computer does not officially support Leopard 10.5,
the other avenues of support would probably not be open to you.
At least not with the old iMac G4 and an unsupported 10.5 install.}
I have an external iSight camera which was included with my G4 Mini
1.5GHz model, and that appeared to work OK with 10.5.8 at one point.
But I really have no need for it, since I don't use photobooth & so on.
And haven't tried that with my iMac G4 computers at all. No need to.
With a computer not equipped with an iSight camera, the Leopard 10.5
installation should still support the eventual addition of one; even if the
computer itself appears to not officially support a Leopard 10.5 install.
(You refer to Leopard Assist, a means to install in slower CPU Macs.)
The FW cable is about the most easy to consider at this point.
In the course of a year, I've found good replacement cables at
several places, even those at thrift stores in perfect shape, work
and I use them for FW external hard disk drives, primarily. To have
spares is nearly always a good idea. Test & keep known good ones.
I'm not certain how the external iSight FW camera may work on
a newer Intel-based 24" iMac with a built-in iSight camera, too.
Does your 24" computer have FireWire 400+800 ports? Can you
choose an external iSight camera and ignore the built-in one?
These secondary topics have probably been discussed in the other
forum area for Intel-based iMac computer models; if you chose to
try & use that camera with a model computer with one built-in...
• Apple - Support - Discussions: for Intel-based iMac
http://discussions.apple.com/category.jspa?categoryID=189
There is a possibility, if never tried and the iMac G4 computer was
acquired second-hand, that the FW port within it may be band; but
the cable is the first item since it is cheapest, in troubleshooting.
So, anyway, the hour is late here (1AM) so hopefully the matter
can be resolved with a known-good replacement FW400 cable.
You should not have to restart the iMac G4 (800?) model in order
to get a FireWire item to be recognized. It should appear in the
System Profiler's list under FireWire, such as things normally do.
Of course, the camera could be defective as well. Been some
time since they were available on sale, new from Apple...
You could ask around to find out if there is a way to use that
external iSight camera with your newer Intel-based 24" Mac
by someone having it ignore its own built-in camera; in a
way as to not affect its normal operation, that is.
Good luck & happy computing!
+{ edited 2x }+

Palm pro wont sync with outlook 2003 and windows device manager?

Palm pro wont sync with outlook 2003 and windows device manager? Files e.g. word docs or excel files sync o.k. but i need my contacts and i only get a error that there is sporblem with my desktop computer.
I am using vista and i have all updates installed.
Post relates to: Treo Pro T850U (Unlocked)

Do you have windows mobile device center installed(WMDC)? If not download it from here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
Be sure you download the correct version for your PC. If you have 32bit OS or 64bit OS. To find this out, right click on Computer under start and select properties. Near the middle it should say 32bit or 64bit. If you know you have the correct software. Open up the control panel and go to sync settings. Right click on the partnership you have setup and select delete. On your device go to Start-->Programs-->Activesync-->Menu-->Options tap on Windows PC and select Delete. Then once both are done resetup your partnership. But this time uncheck everything. Then once it is done syncing. Go to Mobile device settings and change content sync settings and select Contact. Click save and let it sync. Do the same for calendar, tasks, and notes but leave the last item checked. So when Contacts are done syncing you go and check Calendar and leave Contacts

Bluetooth wont keep connection to headphones!

anyone else having this issue? bluetooth wont keep connection to headphones! It works great for anywhere from 20 minutes to 3 hours at a time, then it loses connection, but shows it as being connected on the phone. I have to reboot bluetooth and my headphones and restart any one of the 6 different music players i use.

Hi Go to settings on iPad Reset Network Settings After Reset you need to enter your router wireless key I found that the Router your I S P gives you are not very good I now use a top of range Netgear Router R 6300 bought off Ebay for £70.00 It even works at the top of back garden no problems with iPhone or iPad & Apple TV. Cheers Brian

Bluetooth wont setup with iphon5

Similar Messages

Maybe you are looking for