BluRay error message "code 6, audio buffer underflows. Total bitrate is too high near time = 000000 seconds."

Hello,
I’m trying to create BluRays using Encore and I keep getting the following error messages: ‘code 6, audio buffer underflows. Total bitrate is too high near time = 000000 seconds.”
For info, I created a H264 Bluray - NTSC 24fps master from an Apple prores HQ in Adobe Media Encoder. Duration: 52m, size: 11go. I'm on Mac OSX 10.9.5, the bluray burner is Samsung SE-506CB/RSWD and the BR disks are TDK Blu-ray Disc 50 Spindle - 25GB 4X BD-R - Printable.
I looked around in forums and tried the following without success: replacing disk name to shorter name without space, creating bluray without menu frame, I also tried with a Mpeg2 bluray master. I tried to export a new master but I can't seem to be able to change the audio bitrate.
Can anyone please help ?
Thanks.

Hi Stan, thanks for getting back.
I tried to create a new master from Media Encoder but I can only export audio in PCM, I don't get a dolby option. See pic below.
I tried a new project in Encore and chose PCM instead of Dolby in the preference menu, but I still got the same error. Should I try again limiting bitrate to 15 ? I was on 30 before.
Please help, I've already wasted 10 bluray and this is getting really frustrating!

Similar Messages

When burning a bluray I get this error message: Total bitrate is too high near time = 4.760000

When burning a bluray I get this error message: Total bitrate is too high near time = 4.760000
The video is encoded with sonic cinevison as avchd file and one AC3 file.

What can I do to avoid it?
Well, about the only thing you can do to solve "bitrate too high" errors is to lower the bitrate.

Blu-ray Error: "fatal error". Code: "6". "Video buffer underflows. Total bitrate is too high near time = 1.456333 seconds -

Every time i try to burn a blu-ray, this message appears and i can't proceed to the process.
Can anybody help me? I need it for my job.

I could swear I posted this yesterday. But no, the forum did not. Here is the recovered version....
From http://forums.adobe.com/message/6004943#6004943
You will find a number of other threads with this error message.
I think it usually reflects a real datarate problem, but sometimes because there are spikes that should not have occurred with the transcode settings used.
But the solution/workaround is to reduce datarate.
There may also be times where changes in the type of transcoding (CBR, VBR one or two pass) has fixed the issue for a particular project.
In this thread, Jon Geddes recommends a max of 27 or less.
http://forums.adobe.com/message/5214691#5214691

Blu-ray Error: fatal error, code 6, audio buffer underflows...

Ughh.... So its been a few months since I stopped using CS6 Encore because it loves to crash for all kinds of bad reasons. Today I needed to do a new project, and used a simple 1920x1080p MP4 file created by Adobe Media Encoder, and used a basic menu template in Encore. Also added a slideshow timeline with one Mp3 audio set to loop. During the building image part of the build process, I get the fatal error code 6, audio buffer underflows. Total bitrate too high neat time = 0.00000 seconds -
First off, I set the BR transcode setting to auto and it spends pleanty of time transcoding the file to a 15mbps bitrate, so why is Encore not first taking care of all the source files correctly in transcoding...?

Ok.... 100% the fault of the software. I am an SE, and build systems all the time for my business, so if I knew of these simple problems, Id go into the code and devise a solution...please Adobe, fix Encore.
Here are my simple finding from solving this problem (first post):
- Of the 2 simple Mp4 files produced by Media Encoder, one, which runs only 2 minutes, had a peak of a little over 10mbps. I dropped the file back into Encoder and set the same mp4 profile to max of 6mbps and then replaced the file in the encore project, ran build and it worked fine.
SO.... If I can use a simple free bit of software to look at the bitrate of a file (google Bitrate Viewer) and determine that the peak was possibly too high, why oh why cant adobe write a better transoding logic algorythm to decide if a video in a timeline needs to be reprocessed at a slightly lower bitrate before just attempting a build and then throwing an error. For the love of all that is holy, please tweek your transcoding decision process to prevent these simple errors.

Oracle error message code 1401 op 4, ORA-01401: inserted value too large fo

Hi All
I got this error when I try to run convert tables on our application server. Anyone know why? I am using Oracle 9i
Here is the error message:
Checking Table WORK_INSTRUCTION
Table not in database
Conversion Method - Create Table
Creating Table WORK_INSTRUCTION
Unable to create database table 'WORK_INSTRUCTION'
Oracle error message code 1401 op 4, ORA-01401: inserted value too large for column
WORK_INSTRUCTION definition as followings:
table work_instruction;
field identity
     used_for unique_key
     datatype identity;
{ APR 31/3/03 - Bug Nr WI4}
field wi_admin
{         links_to personnel . identity;}
{         links_to location . identity;}
     links_to lab_section . identity;
{ ARP 31/3/03 - Bug Nr WI5 }
field wi_title
{         datatype text(20);   }
     datatype text(100);
field version
          datatype text ( 4 );
field wi_status
     datatype identity
     prompt_type choose
     choose_type WI_STATUS
     default 'I ' ;
field wi_type
     datatype identity
     prompt_type choose
     choose_type WI_TYPE
     default '0 ';
field sterlab_status
     datatype identity
     prompt_type choose
     choose_type STER_STAT
     default '0 ';
field used_in_lims
     datatype boolean
     true_word 'Yes'
     false_word 'No'
     default 'No' ;
{ ARP WI16 28/5/03 - Extend from 10 to 45 }
field method
     datatype text(45);
field ref_method
     datatype text(100);
field delegate
     links_to personnel . identity;
field date_expire
     datatype date;
field date_draft
     datatype date;
field double_method
     datatype boolean
     true_word 'Yes'
     false_word 'No'
     default 'No' ;
field technique
     datatype identity
     prompt_type choose
     choose_type TECHNIQUE
     default '0 ';
field date_distribute
     datatype date;
field report_date
     datatype date;
field group_autho
     datatype text ( 16 );
field astm_volume
     datatype text ( 6 );
field date_non_active
     datatype date;
field translated_in
     datatype text(10);
{ ARP WI16 28/5/03 - Extend from 60 to 2000 }
field comments
     datatype text(2000);
field doc_path
     datatype text ( 300 )
     prompt_type user_defined
     library 'TEST_SOP_FILE'
     routine 'file_browse';
field modified_on
     datatype date
     used_for modified_on ;
field modified_by
     links_to personnel.identity
     used_for modified_by;
field modifiable
     datatype boolean
     used_for modifiable;
field removeflag datatype boolean
     used_for remove_flag;
{ MOD TDR - 10/04/03 - Link to livelink document }
field livelink_url
datatype text ( 300 ) ;
Thanks
Li

Verbatim from the manual:
ORA-01401:     inserted value too large for column
Cause:     The value entered is larger than the maximum width defined for the column.
Action:     Enter a value smaller than the column width or use the MODIFY option with ALTER TABLE to expand the column width.You should find which value is bein attempted to be inserted into a column with a capacity shorter than the value length.
~ Madrid.

Blu-ray Error: "file already exists", Code: "6", "Audio buffer underflows. Total bit rate too high

Hopefully someon can help me out here - I'm stuck in my tracks. I'm reading through lots of threads on this topic, but don't understand what is going wrong here. CS6. Note: I have used Encore prior to put this material on a disc. I presently have a separate sequence paired down with only about 1/5 of the whole production. 1920x1080i, 29.97, H.264 Blu-ray, VBR 2-pass, PCM inside PP to produce .m4v/.wav. Here is what is confusing me - I tried a target of 10 and a max of 20 and I still get this error. I have tried different max bit rate "Default Transcode" settings in Encore as well. Note the time code listed "0.000000" - maybe that tells someone something. I don't really understand Encore yet, so maybe it is something I set wrong in Encore vs. my exports?

There are many similar, but not identical errors. And I assume you had already followed John's advice to review older threads. It is true they never quite pin a single set of issues down.
What specific version of Encore? Updated to 6.0.2.004? Encore staff once said updates solved some of these errors.
You say .wav for source files in Encore. But what format in the project? ac3?
Your versiono f the error is different from other one I see because it has a "audio buffer" rather than "video buffer" underflow.

HT201210 Just replaced the battery in my iPhone 4S. Before doing so I backed-up then wiped the phone. Now when I go to restore it, it gets about 3/4 done and that is when I get an error message, "Code 1." does this mean I fried it?? :-(

Hello,
Just replaced the battery in my iPhone 4S. Before doing so I backed-up then wiped the phone. Now when I go to restore it, it gets about 3/4 done and that is when I get an error message, "Code 1." does this mean I fried it??

Hey joshuafromisr,
If you resintall iTunes, it should fix the issue. The following document will go over how to remove iTunes fully and then reinstall. Depending on what version of Windows you're running you'll either follow the directions here:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
http://support.apple.com/kb/HT1925
or here:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
http://support.apple.com/kb/HT1923
Best,
David

Iphone 4 switched off error message code 21

i phone 4 just switched its self off and wont restart and when connected to itunes for reboot we get error message code 21

Error 20, 21, 23, 26, 28, 29, 34, 36, 37, 40
These errors typically occur when security software interferes with the restore and update process. FollowTroubleshooting security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Also, check your hosts file to verify that it's not blocking iTunes from communicating with the update server. See iTunes: Advanced iTunes Store troubleshooting—follow steps under the heading Blocked by configuration (Mac OS X / Windows) > Rebuild network information > Mac OS X > The hosts file may also be blocking the iTunes Store. If you have software used to perform unauthorized modifications to the iOS device, uninstall this software prior to editing the hosts file to prevent that software from automatically modifying the hosts file again on restart.

Authorisation on my pc has been lost, when I try to reactivate I get the following error message "code: E_AUTH_NOT_READY" What can I do?

For some reason I can not get into my ADE and get the error message "code: E_AUTH_NOT_ READY      Digital Editions encountered an error on the activiation server.
What can I do as it will not let transfer items to my Sony reader. Thank you

yes, I agree with what you say: the note '==> ...' is the solution to
my problem, found it after some time in another thread
     regards
     Von: sjpt <[email protected]>
     An: zwergenerv <[email protected]>
     Betreff: after updating ADE to version 2.0 I
am getting the error message 'code E_AUTH_NOT_READY'
     Datum: Mon, 23 Sep 2013 10:59:41 +0200
RE: AFTER UPDATING ADE TO VERSION 2.0 I AM GETTING THE ERROR MESSAGE
'CODE E_AUTH_NOT_READY'
created by sjpt in Adobe Digital Editions - View the full
discussion

After updating ADE to version 2.0 I am getting the error message 'code E_AUTH_NOT_READY'

after updating ADE to version 2.0 I am getting the error message 'code E_AUTH_NOT_READY' when trying to authorize my computer (Adobe Id is correct, password I have refreshed, but ..) what to do?
Running ADE on WinXP with recent SP
===> use CTRL-SHIFT-D in ADE to de-authorize and then re-authorize vial Help-Menu

yes, I agree with what you say: the note '==> ...' is the solution to
my problem, found it after some time in another thread
     regards
     Von: sjpt <[email protected]>
     An: zwergenerv <[email protected]>
     Betreff: after updating ADE to version 2.0 I
am getting the error message 'code E_AUTH_NOT_READY'
     Datum: Mon, 23 Sep 2013 10:59:41 +0200
RE: AFTER UPDATING ADE TO VERSION 2.0 I AM GETTING THE ERROR MESSAGE
'CODE E_AUTH_NOT_READY'
created by sjpt in Adobe Digital Editions - View the full
discussion

Oracle error message code 1653 op 4, ORA-01653: unable to extend table

Hi
Our application use Oracle 9i as database. I modified one of tables and try to convert it from this application, then I got an Oralce 1653 error as followings:
Creating Table SAMPLE_T
Copying data from SAMPLE to SAMPLE_T
Unable to move data from table 'SAMPLE' to table 'SAMPLE_T'
Oracle error message code 1653 op 4, ORA-01653: unable to extend table SAND.SAMPLE_T by 1024 in tablespace SAMPLE_RESULT
I suspect the tablespace SAMPLE_RESULT is not big enough and also can not extended automatically, but not sure if it is right or there maybe other reasons behind this error.
Any idea?
Thanks
Li

Lets try .....
SQL> select tablespace_name,sum(bytes)/1024 from dba_free_space where tablespace_name='USERS' group by tablespace_name;
TABLESPACE_NAME SUM(BYTES)/1024
USERS 384
SQL> alter database datafile 'C:\ORACLE\ORADATA\MYDB\USERS01.DBF' autoextend off;
SQL> alter table scott.emp allocate extent;
Table altered.
SQL> /
alter table scott.emp allocate extent
ERROR at line 1:
ORA-01653: unable to extend table SCOTT.EMP by 128 in tablespace USERSI believe you must add more space to tablespace SAMPLE_RESULT or set the autoextend on for associated datafiles.
Hope it help ..
Bhupinder

HT201210 iam getting a error message code of 3194 when trying to restore iphone 4 on itunes

iam getting a error message code of 3194 when trying to restore iphone 4 on itunes

http://support.apple.com/kb/TS3694

Touchscreen not working: error message code 45, says "device is not connected to the computer"

My subject message basically says it all. My touchschreen is not working at all. I went into device manager and found error message code 45, which states that the "device is not connected to the computer."
I have tried updating drivers, uninstalling and reinstalling the device, and other things, but nothing working.
All advice appreciated.

Hi @Jim9 ,
Welcome to the HP Forums!
I saw your post regarding the error code 45. From what you have described this sounds like it is a hardware issue. The only real troubleshooting I can recommend (that you haven't already done), is going a full System Recovery to restore it back to factory defaults. If the issue still occurs then we know it is a hardware problem.
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."

I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."
I don't have anything else plugged into my MBP, so I am confused as to what's going on. This problem has never happened before. MBP is less than a year old - about 9 months old. HELP

Get a powered USB hub.
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

I tried to sync my Macbook Pro photos in iPhoto with my iPod Touch. I have done this numerous times, but today I got an error message saying the required file cannot be found. At the same time all of my photos on my iPod vanished. Can anyone help me?

I tried to sync my Macbook Pro photos in iPhoto with my iPod Touch. I have done this numerous times, but today I got an error message saying the required file cannot be found. At the same time all of my photos on my iPod vanished. Can anyone help me?

Try deleting the photo cache from your computer and then re-try the photo sync - the location of the cache, and how to delete it, is on this page http://support.apple.com/kb/TS1314

BluRay error message "code 6, audio buffer underflows. Total bitrate is too high near time = 000000 seconds."

Similar Messages

Maybe you are looking for