BluRay with G4 Mirror?

Hello. I have a G4 Mirror dual 1.25GHz w/ 1 GB ram. My internal DVD/CR burner is dead (won't read or write). I was thinking about replacing it, but I would really prefer to just get an external BluRay reader/writer that does DVDs & CDs too.
Question is: Can I get it to work on my computer with my current operating system??
My concerns:
My current OS is 10.3.9. I plan to upgrade to tiger but I can't because my comp obviously can't read any installation CDs right now. Are BluRay readers compatible with 10.3.9?
All BluRays I find use eSATA so can I install a PCI card to give my G4 eSATA, also without upgrading my OS?
If I can get a BluRay to work on my comp with my current OS, then any suggestions on which PCI cards or BluRay burners would be awesome.
Thank you in advance!!

hmm.. it wouldn't let me type anymore.
But anyway...
So what do you think about that combination? Toast 9 + the Mercury Pro Super Multi Blue Blu-Ray external drive?
I already have an external FW, and it's good for a mirror of my computer and a few offline archives, but in general, I want to find a way to archive photos from sessions that I have edited & completed but don't need online anymore. Right now, I have to burn all to a DVD which doesn't hold much. (And I've been working only from an old laptop because my MDD OS can't be updated to run Photoshop CS3 or CS4 and the laptop is the only DVD burner working.)
I wish I could upgrade my mac now, but since I can't afford it, I thought that getting an external blu-ray to at least use as a DVD/CD burner would be good so then when I can afford a new comp, I would already have blu-ray. It seems a bit of a waste to replace my dead internal DVD/CD-RW but I need something to be able to upgrade my OS. Right now I'm stuck - unless there's some way to install tiger onto my external FW drive & then install on my MDD?
What do you think the future of blu-ray is? Will I just be getting myself into a pickle if I invest in the external blu-ray only to have it not become mainstream like DVDs have become? (And then have problems retrieving my archives?)

Similar Messages

HT204291 My iPad 4 does not show up on my TV screen when in AirPlay mirroring mode using WiFi. The iPad displays AirPlay set to TV with the Mirroring On (green). My iPad IOS software is 8.2 and my Apple TV software is at 7.1. The TV displays the Apple

My iPad 4 does not show up on my TV screen when in AirPlay mirroring mode using WiFi. The iPad displays AirPlay set to TV with the Mirroring On (green).
My iPad IOS software is 8.2 and my Apple TV software is at 7.1. The TV displays the Apple Menu. The “Settings” does however displays the General menu allowing me to see:
Apple software: 7.1 (7003)
Apple TV: Model No. A1464, Part No. MD199B/A
Signal Strength shows 5 circles.
It does not display the iPad screen but when I use the BT Sport App I can hear the sound but there is no video. I have searched the internet for a solution to no avail. The problem first arose when the IOS was at 8.1+ but it worked correctly briefly when I updated to IOS 8.2. Can you help please?

Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.
If you are still having problems, the following article(s) may help you.
Troubleshooting AirPlay
Troubleshooting Wi-Fi networks and connections
Recommended Wi-Fi settings
Wifi Diagnostic Software (for Mac users)
You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.
When making adjustments to your network for better optimisation, you may find some of the points mentioned on this page helpful.

How to Delete and Reset a Lost Root Password on a System With a Mirrored ??

hi All,
we are experiencing problem,lost root password on Solaris 10 Sparc T5120, with mirror root,
and we found the solution from Metalink.oracle.com, has anyone have try this??
here list capture the file system :
Filesystem size used avail capacity Mounted on
*/dev/md/dsk/d10 2.0G 349M 1.6G 18% /*
*/dev/md/dsk/d40 9.8G 563M 9.2G 6% /usr*
*/dev/md/dsk/d30 9.8G 1.4G 8.4G 15% /var*
*/dev/md/dsk/d50 7.9G 310M 7.5G 4% /opt*
*/dev/md/dsk/d600 3.8G 4.3M 3.8G 1% /home*
*/dev/md/dsk/d602 471M 20M 404M 5% /app/controlm*
*/dev/md/dsk/d601 471M 251M 173M 60% /app/ctsa*
*/dev/md/dsk/d604 4.9G 1.1G 3.8G 23% /app/oramon*
*/dev/md/dsk/d603 20G 11G 8.2G 58% /app/oracle*
*/dev/md/dsk/d606 39G 10.0G 29G 26% /proj/iprdb01/orafra/iprod01p*
here the step :
Solstice DiskSuite[TM] Software: How to Delete and Reset a Lost Root Password on a System With a Mirrored Root Disk [ID 1010755.1]
Solution
Steps to Follow
How to delete and reset a lost root password on a system with a mirrored root disk.
1) Insert the Solaris[TM] Operating System CD-ROM into the CD-ROM drive.
2) Once the CD-ROM is in the drive, perform a stop-a. This brings the system down to the "ok" prompt.
3) From the "ok" prompt, perform a single-user boot from the Solaris OS CD-ROM.
ok boot cdrom -s4) At the "#" prompt, determine which disk is the system's boot disk (containing the root file system). There are several Oracle architectures and various configurations of systems when it concerns a boot disk. As a general rule, most boot disks are attached to controller 0 (c0). Usually, their SCSI target is
either 3 (t3) or 0 (t0). However, Oracle machines are very flexible, and the boot disk could be at a different location. If you are not sure which disk is your boot disk, perform the following steps to determine the location of the boot device:
a) # eeprom boot-device
The output might appear to be simple, such as "disk" or "disk1" or more complicated, such as a pathname "/iommu/sbus/espdma@4,8400000/...../sd@3,0:a".
b) Make note of the boot-device. If the boot-device is a pathname, it is beyond the scope of this information to provide the location of the customized boot disk. However, for most configurations,
finding the customized boot disk is an easy task. The "Format" command shows all available disks:
#format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
(enter its number): c) Enter d to exit format.
Now, you will have an idea what disks are on the system. Therefore, if the boot-device is "disk" and format shows "c0t0d0" (on some systems "c0t3d0") then that is the boot device. If boot-device
shows "disk1" and format shows "c0t1d0," then that is the boot device. If format shows multiple disks, then based on what the "eeprom boot-device" command shows, the system's boot disk would be:
boot-device format
disk c0t0d0 or c0t3d0 (machine dependent)
disk1 c1t0d0
disk2 c0t2d0
disk3 c0t3d0 or c0t0d0 (machine dependent)
and so on ....
5) Because the system was not brought down gracefully (no root password means having to use the Stop-a keystroke to "crash" the system), you need to run "fsck" to clean the root partition (slice). The fsckalso confirms that you selected the proper slice.
# fsck /dev/rdsk/c1t0d0s0
where the X and Y are determined by the previous procedure. It is also possible to have a root partition which is not on slice 0 (s0), but, again, that is not a standard configuration.
The output of "fsck" looks like this:
** /dev/rdsk/c1t0d0s0
** last mounted on /
** Phase 1 .....
The second line in the output of "fsck" ("** Last mounted on /") confirms that this is the correct root filesystem partition. Answer "y" to any questions fsck asks. There shouldn't be too many items
needing repair. If there are, there is a possibility of a corrupted root filesystem. After fsck is finished, mount the root partition:
# mount /dev/dsk/c1t0d0s0 /a
Again, X and Y are the same as for the fsck command.
For example:
# mount /dev/dsk/c1t0d0s0 /a
6) From the root prompt, set the proper TERM type command (such as vt100, dtterm, sun, and so on)
by entering this command:
# TERM=sun; export TERM
7) Use the VI text editor to edit the /etc/shadow file:
# vi /a/etc/shadow
8) The first line of the /etc/shadow file is the one you want to modify.
It looks like this:
root:c3.yAVmYodWsc:6445::::::
9) Delete every character between the first and second colons in the first line of the file. When you finish deleting the characters, the line should look like this:
root::6445::::::
10) Press the Escape key, then enter the following to save the file and exit vi:
:wq!
11) Use the VI text editor to edit the /etc/system file andremove the "rootdev" line shown below:
# vi /a/etc/system
*rootdev:/pseudo/md@0:0,0,blk
Don't comment out the "rootdev" line. Actually remove it.
12) In the /a/etc/vfstab file, replace the lines for the system filesystem meta-devices with their underlying partitions. For example, change lines from
/dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no -
to
/dev/dsk/c1t0d0s0 /dev/rdsk/c1t0d0s0 / ufs 1 no -
ONLY change the lines for root (/) and the filesystems that were affected by the actions you took in step 1 of this procedure. All other metadevices may stay as is in this file.
13) Unmount root, check the root filesystem, and then stop the system:
# cd /
# umount /a
# fsck /dev/rdsk/c1t0d0s0
# stop-a
14) Boot to single-user mode:
ok boot -swTHIS STEP IS VERY IMPORTANT; YOU MUST BOOT TO SINGLE-USER MODE TO AVOID FILESYSTEM CORRUPTION.
If the system does not boot to single user mode, you might have made a mistake in the previous steps.
15) Because the root password was cleared in an earlier step, press Return when prompted for the the root password. Once you are in single-user mode, you must clear the metamirrors and all the sub-mirrors for the root filesystem. For example, if root (/) is d0, run the following command:
# metaclear -f -r d0
Running the metaclear command not only clears the metamirror but also clears the submirrors that are part of this mirror.
16) When the metamirror is cleared, continue the boot up to multiuser mode by either pressing CTRL-D or by entering the following:
# exit
Now everything should be as it was, except that the system partition is on the underlying partition and isn't mirrored. You will simply need to re-create the metadevices for the root mirror as you had originally.
many thanks

Hi,
Halt your machine.
Boot with fail-safe mode.
format and list out the disks. (You can get the root & mirror disk (c#t#d#) details from /etc/lvm/md.tab of your root or mirror disk. Earlier explorer output may help)
Mount the root disk and remove the password entry in /etc/shadow
umount it.
Mount the mirror disk and remove the password entry in /etc/shadow
umount it.
reboot the server.
Hope this helps!

Im not satasfied with 6.0 i miss youtube and some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

Im not satasfied with 6.0, i miss youtube, some apps are slower, facebook wants premission to access my contacts, and how do i use apple tv feature with out mirroring?

That is awesome, works perfectly.
I'll get it worked into my main script. Is this Action Manager code, and not just regular Javascript from the Scripting Dictionary? I can't tell the difference. I'll see whether or not it's actually faster than Applescript.
Thanks. I know Scripting Listener records a bunch of stuff, but it's pretty amazing to me that playing back this line does the same thing that playing back the 1,011 lines Scripting Listener puts out.
Thanks.

Trouble With Port Mirroring (SG200-08)

Trouble with port mirroring.
Even though both Tx and Rx is specified, only getting half the conversation. Ping reply only for instance. And when pinging from other locations no traffic at all.
Please help
SG200-008
FW Version: 1.0.2.0
Boot Version D.3.1
Thanks

I also have problem with the mirroring of port on my SG200-08. The firmware is 1.0.6.2.
I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2. The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
Does anybody knows a solution to this?

Problem with AirPlay mirroring with iTunes

Hi,
I have a new iMac (purchased April 2013) running OS X Mountain Lion and am having issue with AirPlay mirroring with iTunes via Apple TV 3 running the latest update.
I have no problem streaming ITunes music (audio) to my Apple TV 3 via AirPlay.
However, when I enable Airplay Mirroring to ATV3 (either via System Prefs or via the Airplay Mirroring menulet icon at upper right of the screen), 2 things happen:
1. My iMac screen gets mirrored to my HDTV via ATV3 as expected (good)
2. Music (audio) stops playing via ATV3 (bad) - this is the key issue I am trying to resolve
When i disable Airplay Mirroring, I am able to again play music via ATV3.
Am I missing a setting somewhere to enable BOTH video and audio Airplay mirroring from my iMac via ATV3?
Thanks,
Kevin

I think I have found the reason for my problem...
http://support.apple.com/kb/HT5404?viewlocale=en_US
Supported Macs
AirPlay Mirroring in OS X Mountain Lion takes advantage of the hardware video encoding capabilities of 2nd and 3rd Generation Intel Core processors. Hardware video encoding allows AirPlay Mirroring to efficiently deliver high frame rates while maintaining optimal system performance. The following Mac models have processors that support AirPlay Mirroring:
iMac (Mid 2011 or newer)
Mac mini (Mid 2011 or newer)
MacBook Air (Mid 2011 or newer)
MacBook Pro (Early 2011 or newer)
My device is an older Model

Was watching a movie with AirPlay mirroring on apple tv from iMac. Got a Skype call. Turned off AirPlay on atv and on iMac. Could not hear my Skype caller until I unplugged the atv. What else could I have done?

Was watching a movie with AirPlay mirroring on atv from iMac.   Got a Skype call. Could not hear caller until I unplugged atv. Turned off AirPlay on both atv and iMac. Could not hear Skype caller until I turned off atv. What else could I have done?

I checked and found that the router did not have the latest firmware.   It does now.   The issue is still there.   I did a little research and found that the model number of my Apple TV (MC572LL/A) shows that it is a 2G version which uses the A4 chip.   The latest version uses the A5 chip and is 1080 capable. Both are supposed to be capable of using type "N" routers.   I don't think that should be an issue but I wonder if later updates may have introduced some issues in the 2G version.
I am going to try changing the "N" channel also- just to see if that makes any difference. The istumbler app does not show any "N" networks in my area so it is defaulting to 149.   I will note that even 1 foot away from the router I only get 75-85% for signal.   I would expect it to be 100% since it is so close.   I am also seeing noise go up from typically 13% to 21% when it is on channel 3 and that close.       I will play change locations and channels and see if there is any improvement.

Bought new Transformers on bluray with HD digital. Followed all the sets to register it. It is in iclid but will not download? Please advise.

Just bought new Transformers on bluray with HD digital. Followed all the steps to register it. It is in icloud but will not download? Please advise.

What online service did you download the movie from? If it wasn't iTunes, you probably can't play it in iTunes (and iCloud doesn't store movies in either case).
Matt

Mac OS X 10.7.4 ARD Issues When Observing/Controlling Computers with Display Mirroring/Different Resolutions

As if Macs in an enterprise environment could be more difficult to manage, now since our upgrade to OS X 10.7.(4) I have lost the ability to remotely control numerous Macs in our organization. The issue occurs when attempting to control a Mac running OS X 10.7.(4) that has their Display mirrored and the resolution does not match on both displays. What happens is that I can see the remote screen however it does not fill the entire Observe/Control window. Instead, the remote screen takes up about 50% of the window, the rest is black but sometimes will display a mirror image of the remote screen in the black area. What?! Yeah, I've attached a screenshot because this is ridiculous. The real problem is that I cannot control the computer when it has reached this state, the mouse no longer functions properly, it is not clicking where I place the mouse, etc. I have made sure that I have all updates including ARD Client/Server updates. I even tried VNC but as I have come to find out that is a whole other issue (doesn't work, sends me to the login screen, etc).
So here's what I need:
- A patch that is going to fix this issue
- A script to run that is going to change the remote screen resolution (I still have the ability to run remote scripts, etc. simply not Observe/Control)
Ideas?
<Image Edited by Host>

I found a way to work around this issue. Not a fix but a work around.
This is little application some one wrote to toggle mirroring on and off.
Mirror Displays
If you put this application in the client computer's /Aplications folder
you can use ARD or SSH to run the app and switch modes.
The problem only occurs for me when a client is set to mirror dissimilar displays with different aspect ratios.
I am only seeing this in Lion 10.7.4 and 10.7.5
Hope it helps someone....

2nd display with out mirroring

I want to use my 17" apple display with my iMac, without doing mirroring. I heard there was a firmware hack to do this. Can anyone show me the website and tell me about the warranty effects. thanks.

The "hack" can be found here:
http://www.rutemoeller.com/mp/ibook/ibook_e.html
it works very well on both my iBook G4 and my iMac G5 17" rev B. (both running Tiger)
I even use it with the Apple s-video adapter on my TV.

LG TV as a Monitor - Problem with not Mirroring Display

I used to be able to extend to my LG TV and use that as an additional monitor side by side with my Macbook Pro 17" but now it only allows me to mirror. What has changed. I have tried different HDMI cables.

Mirrored mode mirrors the display including resolution. Use extended mode not mirrored mode to set the external display resolution to the TV's native mode.

Need help with a mirror image effect

For most of our product photos, I create a copy of the image, flip it vertically, fade it out, and then move it down to create a mirror image effect. Simple enough. But this one I'm having a problem. The product has 4 legs, and from this view, the back 2 legs are shorter. When I do my normal steps that I listed, I get similar to what you see below. I know all about drawing a marquee around part of the reflection, hitting Ctrl+T and then holding down Ctrl+Shift to skew just what's in the marquee. I've done this technique a lot, but it does not work for this particular image. What do I have to do to get the reflection of the back legs to line up with the actual back legs in the image? Thanks.

Well, Photoshop is not a 3D rendering program and you can only fake it by painting or assembling the reflection using your artistic skills and knowledge of perspective and reflections. From certain angles and with certain objects this could be quite easily done by just mirroring the 2D image but in other cases like this it wont' work. I made a quick scene in a 3D program to show you how the refection will actually be in real life - you will see the bottom of the table in the reflection and this is missing from the 2D image. You can assemble and position separately parts of the reflection from the 2D image by using the front sides of the table and and legs but the rest (bottom) of table has to be created from scratch.

DW8 - Need help with Flash Mirror Gallery by Flashdevelopment24

I just purchased an image viewer called Flash Mirror Gallery by Flashdevelopment24:
http://www.flashdevelopment24.com/extensions/flash_photo_gallery_06.aspx
I use DW8. Unfortunately the wizard and the instructions are WAY beyond me. I can insert the object on my page but I have no clue how to import images into it, do I need to create separate thumbnails?, etc. Its a European company and the English isn't taht great either which doesn't help.I went through all their FAQs and examples and I don't have a clue.
I'm doing something very simple, all I need are VERY simple directions on how to make this work. It would be best if there was a YouTube or other video tutorial available. I paid 45 buck for this and it useless to me right now. Help!

I paid 45 buck for this and it useless to me right now. Help!
Sorry can't help, don't know the product at all.
If you are having problems with it, then it's best to contact the people you purchased it from no? They should either help you with support issues, you you should get a refund if it doesn't work as expected.
Nadia
Adobe® Community Expert : Dreamweaver
Unique CSS Templates | Tutorials | SEO Articles
http://www.DreamweaverResources.com
Web Design & Development
http://www.perrelink.com.au
http://twitter.com/nadiap

Problem with local mirror syncing

Hi mens! And sorry, my English is bad.
I rewrite script from here for syncing mirror for my local network.
That's what happened http://ix.io/1aK or http://paste.pocoo.org/raw/263591/ or permanent http://ix.io/user/atommixz
It support http (maybe ftp?) mirroring other repos. Using lftp for it.
#!/bin/bash
# The script to sync a local mirror of the Arch Linux repositories and ISOs
# Copyright (C) 2007 Woody Gilk <[email protected]>
# Modifications by Dale Blount <[email protected]>
# and Roman Kyrylych <[email protected]>
# and Vadim Gamov <[email protected]>
# and Aleksey Frolov <[email protected]>
# Licensed under the GNU GPL (version 2)
USECOLOR=yes
. /etc/rc.d/functions
# Filesystem locations for the sync operations
SYNC_HOME="/home/mirror"
SYNC_LOGS="$SYNC_HOME/logs"
SYNC_FILES="$SYNC_HOME/files"
SYNC_LOCK="$SYNC_HOME/mirrorsync.lck"
SYNC_REPO=(core extra community multilib iso archlinuxfr catalyst)
#SYNC_REPO=(archlinuxfr catalyst)
typeset -A REPO_URL
REPO_URL=(
[archlinuxfr]='http://repo.archlinux.fr/x86_64'
[catalyst]='http://catalyst.apocalypsus.net/repo/catalyst/x86_64'
#SYNC_SERVER=distro.ibiblio.org::distros/archlinux
SYNC_SERVER=mirror.yandex.ru::archlinux
RATE_LIMIT=50 # in kb/s
TIME_OUT=5 # in sec
# Set the format of the log file name
# This example will output something like this: sync_20070201-8.log
#LOG_FILE="pkgsync_$(date +%Y%m%d-%H).log"
LOG_FILE="pkgsync_$(date +%Y%m%d).log"
#Watchdog part (time in seconds of uninterruptable work of script)
# Needed for low-speed and/or unstable links to prevent
# rsync hunging up.
# New instance of script checks for timeout, if it occurs
# it'll kill previous instance, in elsecase it'll exit without
# any work.
WD_TIMEOUT=10800
# Do not edit the following lines, they protect the sync from running more than
# one instance at a time
if [ ! -d $SYNC_HOME ]; then
printhl "$SYNC_HOME does not exist, please create it, then run this script again."
exit 1
fi
if [ -f $SYNC_LOCK ];then
OPID=`head -n1 $SYNC_LOCK`;
TIMEOUT=`head -n2 $SYNC_LOCK|tail -n1`;
NOW=`date +%s`;
if [ "$NOW" -ge "$TIMEOUT" ];then
kill -9 $OPID;
fi
MYNAME=`basename $0`;
TESTPID=`ps -p $OPID|grep $OPID|grep $MYNAME`;
if [ "$TESTPID" != "" ];then
printhl "exit";
exit 1;
else
rm $SYNC_LOCK;
fi
fi
echo $$ > "$SYNC_LOCK"
echo `expr \`date +%s\` + $WD_TIMEOUT` >> "$SYNC_LOCK"
# End of non-editable lines
# Create the log file and insert a timestamp
touch "$SYNC_LOGS/$LOG_FILE"
printhl "Starting sync on $(date --rfc-3339=seconds)" | tee -a "$SYNC_LOGS/$LOG_FILE"
for repo in ${SYNC_REPO[@]}; do
repo=$(echo $repo | tr [:upper:] [:lower:])
printhl "Syncing $repo" | tee -a "$SYNC_LOGS/$LOG_FILE"
NEXT=false
for i in ${!REPO_URL[*]}; do
if [ $i = $repo ]; then
mkdir -p "$SYNC_FILES/$repo"
cd "$SYNC_FILES/$repo"
lftp -c "\
set xfer:log no; \
set net:limit-rate $[RATE_LIMIT * 1000]; \
mirror \
--delete \
--only-newer \
--verbose=3 \
${REPO_URL[$repo]}" | tee -a "$SYNC_LOGS/$LOG_FILE"
date --rfc-3339=seconds > "$SYNC_FILES/$repo.lastsync"
NEXT=true
#sleep $TIME_OUT
fi
done
if $NEXT; then continue; fi
rsync -rtvHh \
--bwlimit=$RATE_LIMIT \
--no-motd \
--delete-after \
--delete-excluded \
--prune-empty-dirs \
--delay-updates \
--copy-links \
--perms \
--include="*/" \
--include="latest/*x86_64.iso" \
--include="latest/*sum*.txt" \
--include="archboot/latest/*.iso" \
--include="os/x86_64/*" \
--exclude="*" \
$SYNC_SERVER/$repo "$SYNC_FILES" | tee -a "$SYNC_LOGS/$LOG_FILE"
# Create $repo.lastsync file with timestamp like "2007-05-02 03:41:08+03:00"
# which may be useful for users to know when the repository was last updated
date --rfc-3339=seconds > "$SYNC_FILES/$repo.lastsync"
# Sleep 5 seconds after each repository to avoid too many concurrent connections
# to rsync server if the TCP connection does not close in a timely manner
sleep $TIME_OUT
done
# Insert another timestamp and close the log file
printhl "Finished sync on $(date --rfc-3339=seconds)" | tee -a "$SYNC_LOGS/$LOG_FILE"
printsep >> "$SYNC_LOGS/$LOG_FILE"
# Remove the lock file and exit
rm -f "$SYNC_LOCK"
unset REPO_URL
exit 0
But I'm have problem. If I'm run
sudo pacman -Syu
on my server, it's fine work.
[atommixz@fileserver ~]$ date; sudo pacman -Syu; echo "------"; date; sudo pacman -Syu
Сбт Сен 18 19:55:47 MSD 2010
:: Синхронизируются базы данных пакетов...
core 35,7K 14,2M/s 00:00:00 [#############################################################] 100%
extra 465,9K 189,3M/s 00:00:00 [#############################################################] 100%
community 383,1K 198,6M/s 00:00:00 [#############################################################] 100%
archlinuxfr не устарел
:: Запускается полное обновление системы...
нечего выполнять
[atommixz@fileserver ~]$ date; sudo pacman -Syu
Сбт Сен 18 19:55:48 MSD 2010
:: Синхронизируются базы данных пакетов...
core не устарел
extra не устарел
community не устарел
archlinuxfr не устарел
:: Запускается полное обновление системы...
нечего выполнять
But if I'm try it on my desktop, it work wrong. Always reget base. But it is updated properly.
[atommixz@relentless ~]$ date; sudo pacman -Syu; echo "------"; date; sudo pacman -Syu
Сбт Сен 18 19:58:42 MSD 2010
:: Синхронизируются базы данных пакетов...
core 35,7K 34,0M/s 00:00:00 [#############################################################] 100%
extra 465,9K 58,7M/s 00:00:00 [#############################################################] 100%
community 383,1K 57,9M/s 00:00:00 [#############################################################] 100%
multilib 19,3K 34,7M/s 00:00:00 [#############################################################] 100%
archlinuxfr 18,6K 42,6M/s 00:00:00 [#############################################################] 100%
catalyst 2,2K 67,7M/s 00:00:00 [#############################################################] 100%
:: Запускается полное обновление системы...
нечего выполнять
Сбт Сен 18 19:58:43 MSD 2010
:: Синхронизируются базы данных пакетов...
core 35,7K 34,0M/s 00:00:00 [#############################################################] 100%
extra 465,9K 58,7M/s 00:00:00 [#############################################################] 100%
community 383,1K 64,8M/s 00:00:00 [#############################################################] 100%
multilib 19,3K 48,9M/s 00:00:00 [#############################################################] 100%
archlinuxfr 18,6K 38,9M/s 00:00:00 [#############################################################] 100%
catalyst 2,2K 55,5M/s 00:00:00 [#############################################################] 100%
:: Запускается полное обновление системы...
нечего выполнять
What am I doing wrong?

I'm not sure, but your script may be too old. That is, it may no longer work.
I believe that creating a local mirror is discouraged due to the high bandwidth needed to do that.
Perhaps you could try this instead.

HT201343 How can I make my 2013 Mac Pro been compatible with airplay & mirroring display

How can I make my 2013 Mac Pro been compatible with airplay & mirroring display ?
Thanks for any help !

2013 Mac Pro would be compatible
http://support.apple.com/kb/ht5404

BluRay with G4 Mirror?

Similar Messages

Maybe you are looking for