Boot camp assistant error update BIOS
I have a Mac Pro 4.1 using 10.6.5 and BC Setup Assistant 3.0.1.
I'd like to enlarge the space on my BC partition of my startup disk, but I have the familiar boot camp assistant error which tells the user that in order to install boot camp you must update the Boot ROM Firmware. I've already updated the firmware to 1.4 (MP4.0081.B07; SMC Version 1.39f5), so this gets me nowhere. What's a little different about my problem than most of the others I've seen is that I have an early 2009 Mac Pro, not a laptop, AND journaling is enabled on all my disks.
I tried downgrading to 10.5.6 by installing it on another drive and starting up from that. It shows that Boot Camp Setup Assistant is version 2.0, but still it tells me that I need upgrade the Boot ROM Firmware.
From within Windows I installed Boot Camp 3.1 and 3.2 and restarted both times. I've run Disk Utility and verified and/or repaired Disk Permissions on startup disks; so, too, Verify Disk.
Any help you can offer over this American Thanksgiving Holiday will be greatly appreciated.
Paragon-Software CampTune $20 can resize.
But I would just put Windows on its own hard drive instead.
Has nothing to do with OS X. Your drive's free space and how fragmented can be an issue when creating Windows partition.
The error message is in error itself and not helpful or accurate.
http://www.apple.com/support/bootcamp
Similar Messages
-
Boot camp assistant error update ROM
I apologize for cross-posting; I had this over at the Snow Leopard forum and it was suggested I try putting this over here.
I have a Mac Pro 4.1 using 10.6.5 and BC Setup Assistant 3.0.1.
I'd like to enlarge the space on my BC partition of my startup disk, but I have the familiar boot camp assistant error which tells the user that in order to install boot camp you must update the Boot ROM Firmware. I've already updated the firmware to 1.4 (MP4.0081.B07; SMC Version 1.39f5), so this gets me nowhere. What's a little different about my problem than most of the others I've seen is that I have an early 2009 Mac Pro, not a laptop, AND journaling is enabled on all my disks.
I tried downgrading to 10.5.6 by installing it on another drive and starting up from that. It shows that Boot Camp Setup Assistant is version 2.0, but still it tells me that I need upgrade the Boot ROM Firmware.
From within Windows I installed Boot Camp 3.1 and 3.2 and restarted both times. I've run Disk Utility and verified and/or repaired Disk Permissions on startup disks; so, too, Verify Disk.
I've tried installing Boot Camp on a new, blank, journaled drive. I get the same update your firmware message.
Any help you can offer over this American Thanksgiving Holiday will be greatly appreciated.No I have only one physical HDD. Here is a diskutil list result
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *500.3 GB disk0
1: EFI 209.7 MB disk0s1
2: Apple_HFS Macintosh HD 499.4 GB disk0s2
3: Apple_Boot Recovery HD 650.0 MB disk0s3
Also here is a system info
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro8,2
Processor Name: Intel Core i7
Processor Speed: 2.5 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GB
Boot ROM Version: MBP81.0047.B27
SMC Version (system): 1.69f3
15-inch, Late 2011
current situation
- I've recovered from external drive (mountain lion 10.8.1 ) which i prepared by Lion Diskmaker before.
Current issues:
1) I have Recovery HD but when I boot from it - Reinstall Mac OS X option is not working
2) I have EFI password and won't be able to clear it as well as reset PRAM
3) Boot Camp Assistant is not working as well with the error in the subject
Any ideas how to fix all of these? -
After 10.8.3 update, Boot Camp Assistant not recognizing my 64-bit Windows 8 disc
Hello all,
Yesterday I got back from spring break and found out there was a new update to ML (10.8.3). After reading a bit, I found out that the new update supported Windows 8 via Bootcamp, so I uninstalled the old Windows 8 I ages ago via Boot Camp Assistant, and updated my OS to 10.8.3. Then, after attempting to install Windows 8 via Boot Camp Assistant, now it rejects my legit copy of Windows 8 Pro 64-bit, with a message saying, "Need 64-bit Windows 8"
A few months after Windows 8 came out, I read up an online guide to install Windows 8 without Apple's official support and it WORKED just fine. I just wanted to reinstall using the official support this time, and see what I get. Haha.
Please help me if you have a solution to this. (No way buying another copy of Windows 8)
Thanks.Had this problem too, found a solution.
1) Download the 64bit Windows 8 Enterprise Evaluation. (http://msdn.microsoft.com/en-us/evalcenter/jj554510.aspx)
2) Go through the Boot Camp process, selecting the downloaded .iso as your image.
3) As soon as your computer restarts, hold the option key. Boot back into OSX.
4) Go through the boot camp process again, BUT only ticking the first two options (in other words, don't touch the partition) selecting your original Windows 8 copy as your image.
5) Reboot while pressing the option key, select the (in my case) USB.
6) Proceed as normal - worked for me. -
Boot Camp Assist can't partition hard drive
Boot Camp won't partition my 500GB internal HD. I get the message:
"The startup disk cannot be partitioned or restored to a single partition. Back up the disk and use Disk Utility to format it as a single Mac OS Extended (Journaled) volume. Restore your information to the disk and try using Boot Camp Assistant again." I had recently used SuperDuper to replace my original single partition internal HD with the new 500GB HD with three partitions. I had not setup Boot Camp on the original HD. After getting the Boot Camp Assist error message on the new HD I used SuperDuper to clone back from my original HD (which was now external) with a single Mac OS Extended (Journaled) volume. I then ran Boot Camp Assist again and got the same message. I ran Disk Utility Verify Disk Permissions and got some errors which I then successfully repaired. I still get the same Boot Camp partition error. Any suggestions?When you partition your drive you are given the option to format it for OS 9, if you choose this option your drive will be formatted to be incompatible with Boot Camp. This incompatiblity will remain when you put it back to a single partition unless you go to options and select the top radio button (format for Intel Mac) to create a GUID Partition Table (at least that's what I did and it fixed the problem).
-
Please advice I am getting an error "Boot Camp Assistant cannot be used. You must update your computer's Boot ROM firmware before using this setup assistant."
No I have only one physical HDD. Here is a diskutil list result
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *500.3 GB disk0
1: EFI 209.7 MB disk0s1
2: Apple_HFS Macintosh HD 499.4 GB disk0s2
3: Apple_Boot Recovery HD 650.0 MB disk0s3
Also here is a system info
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro8,2
Processor Name: Intel Core i7
Processor Speed: 2.5 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GB
Boot ROM Version: MBP81.0047.B27
SMC Version (system): 1.69f3
15-inch, Late 2011
current situation
- I've recovered from external drive (mountain lion 10.8.1 ) which i prepared by Lion Diskmaker before.
Current issues:
1) I have Recovery HD but when I boot from it - Reinstall Mac OS X option is not working
2) I have EFI password and won't be able to clear it as well as reset PRAM
3) Boot Camp Assistant is not working as well with the error in the subject
Any ideas how to fix all of these? -
Need Help how to address problem with undoing partition from BootCamp Assistant- receiving error message
"Boot Camp Assistant cannot be used: You must update your computer's boot ROM firmware before using this setup assistant".
attempted solutions:
http://support.apple.com/kb/HT3964?viewlocale=en_en
http://support.apple.com/kb/HT1379?viewlocale=en_en
Mac HD is already MAc os Extended(journaled)
***problem still persists with above solutions.No I have only one physical HDD. Here is a diskutil list result
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *500.3 GB disk0
1: EFI 209.7 MB disk0s1
2: Apple_HFS Macintosh HD 499.4 GB disk0s2
3: Apple_Boot Recovery HD 650.0 MB disk0s3
Also here is a system info
Hardware Overview:
Model Name: MacBook Pro
Model Identifier: MacBookPro8,2
Processor Name: Intel Core i7
Processor Speed: 2.5 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GB
Boot ROM Version: MBP81.0047.B27
SMC Version (system): 1.69f3
15-inch, Late 2011
current situation
- I've recovered from external drive (mountain lion 10.8.1 ) which i prepared by Lion Diskmaker before.
Current issues:
1) I have Recovery HD but when I boot from it - Reinstall Mac OS X option is not working
2) I have EFI password and won't be able to clear it as well as reset PRAM
3) Boot Camp Assistant is not working as well with the error in the subject
Any ideas how to fix all of these? -
Error message when starting Boot Camp: 'You must update your computers Boot Rom'
I installed the latest firmware updated to my late 2011 13 inch MBP. Rom version is MBP81.0047.B24. Now Boot Camp won't start. Says I need to updated my boot rom. But its updated already. Anyone else having this issue? Thanks.
Fire the people that write meaningless message errors. Oh, can't. Get the point though.
you mean you are trying to use Boot Camp Assistant? Boot Camp has become meaningless through over use for too many things.
It doesn't even know bout your EFI frmware, I can say that.
You should though use Lion Boot Camp Assistant and the BC 4.01 drivers for your system.
Zap pram
repair your hard drive with Disk Utility - from DVD
make sure your free space is not fragmented, is contiguous and also large enough, 40 + 20GB for Windows, and still leave 20GB / 20% free for HFS.
And backup(s). -
Error: Boot camp assistant: Can't install the software because it is not currently available from the Software Update server.
OS 10.9.1
iMac 27-inch, Late 2009
Boot Camp Assistant Version 5.1.0 (473)
Every time I run this I get the above error after I hit "Continue" on the "Save Windows Support Software" page and subsequently hit "Download Windows 7 Support Software."
How do I successfully install 64 bit WIndows 7 on my iMac?
Thank you!Waited a month and tried again with the same result. What gives? Does Apple no longer support Bootcamp with Windows 7? Do they not read these posts and help out customers? If Apple doesn't care and won't help, can anyone else suggest something? My large company does not like Apple and barely supports those of us who buck the trend and buy Macs. If I have to buy a PC to support their software to work from home this only gives them more "ammunition" to decline to support Macs. Any advice anyone can give would be greatly appreciated!
-
When trying in install windows 7 on my mac, the Boot Camp Assistant attempts to fownload windows support software. However, the program continues to return the following error: the windows support software "not currently available from the Software Update server."
Is there another way to get this software?64 bit. I found the support drivers and got the windows installation done. When trying to run the 64 bit support drivers in Windows 7, it says my computer doesn't support 64 bit. Sooooo.....
I'm assuming I have to download the 32 bit support drivers for Windows 7.
Correct? -
Hi!
I am getting the error:
"The startup disk cannot be partitioned or restored to a single partition. The startup disk must be formatted as a single Mac OS Extended (Jounraled) volume or already partitioned by Boot Camp Assistant for installing Windows."
I read up some on google, but all of them says that they have crated a partition and that is the problem, I only have the standard "Macintosh HD".
I tried to create a partition manually in disk utility but then the error message: "Partition failed with error message: Could not unmount disk."
Can anyone help me? It's driving me crazy.
Thanks.This message, and threads like yours got asked daily for over two years, now it is only a couple times a week!!
Is it so hard to follow through? you were to have backup already, clones are best, then erase/format and restore.
Then partition.
Some have been able to use Disk Utility booted from OS X DVD or another drive, and repair the drive.
You have to use Boot Camp Assistant (99.9% anyway) to create and achieve a proper Windows Master Boot Record partition. -
Boot Camp Assistant won't work - keeps asking me to use Software Update.
I am trying to use Boot Camp to install Windows but my Boot Camp Assistant won't work - it keeps asking me to use Software Update. So, even though I know everything is up to date, I start Software Update and it confirms that indeed everything is up to date. I try Boot Camp Assistant again, but the same message appears. I search every possible Boot Camp upgrade to download from Apple but they are all .exe files and need Windows to run, so those don't seem to be what I need. So I am caught in a circle of nothing working. Figures - the ONE weekend I need to install Windows and use a Windows-based program!!! And of course Apple support is closed over the weekend - another great asset to spending thousands of dollars on a product. ANY SUGGESTIONS?
I too am having a similar problem. I am trying to install Windows in a newly created Boot Camp partition. I have Windows 7 but Boot Camp Assistant only mentions XP and Vista. I put in my installation disk of Windows 7 but it refuses to install it. My OS is fully up to date.
-
Boot Camp 2.1 Update: Error, would not install
I tried to update my Boot Camp to 2.1.
The reasoning being, that my dimmer button, my volume button, etc does not work on my Windows Vista Ultimate Side.
Other short cut keys worked (i tried): ie: Print screen via 'fn'altF11, etc
However, when I installed it, the following message appeared.
"the installer encountered errors before Boot Camp could be configured.
To retry these operations at a later time, please run th installer again.
Click Finish to exit the installer."
How can I install the Boot Camp 2.1 updater?
Please advise.
Many thanks.First, backup. Files and system with Ultimate's build-in programs or 3rd party.
run chkdsk for starters. you may want to dabble even more with msconfig and look at your logs, see if there are errors, what startup items and services are running.
I could not install BC 2.1 64-bit even though I have 64-bi9t OS and hardware, maybe because older Mac Pro has 32-bit EFI.
I'd look at uninstalling and reinstalling BC 2.0 and leave well enough alone and focus on just the small issues for now.
Oh, and WinClone is another method and free for backing up NTFS partitions from within OS X worth looking into.
I have not read of the error you got, off hand, that I recall reading.
I really think we need a BC 2.2 at this point in time. -
Network error in boot camp assistant
i can't able to download the windows software and related driver from boot camp assistant, its give me error, "network error",
when i can open every website in my laptop, its coonected to internet....
help me...manually dl the correct pkg here
http://support.apple.com/kb/ht5634 -
when i want to install windows7 on my snow leopard(10.6.4) with boot camp assistant,said that you must update your mac,i do this and try to install windows7 again but i have this problem again?what can i do?
Graham Giles wrote:
Have you seen this type of problem before? I think it could be a serious issue for anyone in a similar position.
No; but then, I've not had occasion to use TDM. I've been using firerwire drives for over 10 years, both FW400 and FW800, with no issues except a bit of instability using a B&W G3 machine.
TDM should be safe. Using cautious, manual copying of files from the Target machine to the Host machine should not result in unexpected loss of files or damage to the Target drive's directories. It should behave exactly the same as if it were an external (to the Host) firewire drive.
• I don't suppose there is anything I can do to 'put back' lost items from a separate Time Machine drive which has an up to date backup on it.
There is probably a way to do that - seems to me that's one of the reasons for a Time Machine volume.
On the other hand, if the Time Machine volume is rigidly linked to the now-absent OS on the original drive, there may be no way to effectively access the files in the TM archive.
I know that using a cloned drive would work well in this instance.
I have no experience with Time Machine, so perhaps someone who has will chime in with suggestions.
With the machine in TDM with the other machine, have you tried running Disk Utility to see if you can effect repairs to the drive? -
I just updated to OS X 10.9.2 and My boot camp assistant won't turn on.
I'm trying to install Windows 7 as I did before.
But now, when i double click the boot camp assistant on desktop it gives me the error message window and says "Boot Camp Assistant has quit unexpectedly".
Please help.When I got the computer, boot camp assistant was on the desktop and I used it to install windows 7 before.
I have never really seen it on my applications folder and right now it isn't in my applications folder either.
Would this be the problem?
I couldn't find out how to re-download the boot camp assistant either...
Maybe you are looking for
-
I have had a problem with my iphone 4s for some time now but I have just been so busy to try and fix it. When I try to disable cellular data in the settings for my apps it will toggle fine, but once I exit and go back in to the cellular settings its
-
Hi, I'm trying to make an imageresize-thingy with PHP from Arch-repos, problem is it keeps saying it can't find the function imagecreatefromjpeg(). In order to have that function availiabe PHP need to be configured with --with-gd and --with-jpeg-dir,
-
Hello All, We have an issue with transaction F110, a user is trying to create a payment proposal and a payment run is being carried out. But when he tries to print this, he is not able to do so.Wheras another user can do so. I have applied trace on
-
Has anyone received an error code of -3212 when trying to access the Itunes Store?
Has anyone received an error code of -3212 when trying to access the Itunes Store?
-
Hi I m trying to install database vault 10.2.3.0 on EBS R12 database (10g -10.2.3.0) . DB vault oui fails with message The installer has not detected any Oracle 10.2.0.2.0 Enterprise Edition database in the system. Its required that you must have at