Boot Camp / Windows Partion... Can it be installed on a separate hard drive

I am just beginning to explore the idea of installing Boot Camp & Windows on a new Intel Mac I will be buying. I've been reading a lot of references to the Windows partition...
Can I dedicate a separate hard drive to Windows rather than partition my primary hard drive? If so would it be best to use an internal drive rather than a Firewire or USB drive. What would a reasonable minimum drive size be?
Thanks for you feedback.
Mike

Hi Mike,
since only the Mac Pro can have more than one internal HD, I assume you are talking about getting one of them
With more than one internal HDs you can put Windows on the second, third, fourth internal HD with the BootCamp Assistant.
On a side note: Windows does not support to be booted from external HDs (neither FireWire nor USB).
Reasonable size depends on what you want to do with it.
Windows XP itself takes up to 3.5GB of HD space after installation, Vista takes up to 10GB.
Add to that the HD space you need for the programs and data you use/produce.
And when keeping in mind the hassle it takes to enlarge the Windows partition if needed, my personal suggestions are:
Windows XP at least 30GB, Vista at least 50GB.
Have you already had a look here http://www.apple.com/support/bootcamp/ especially at the Installation Guide ?
Regards
Stefan

Similar Messages

Can programs be installed on an external hard drive with my mac pro?

Can programs be installed on an external hard drive. I am running low on space. Final Cut Pro X spins off the rendering files which takes a large chunk of space. Like to at least have those rendered files on an external drive, but can find that option to make it happen.
Hardware Overview:
   Model Name:   MacBook Pro
   Model Identifier:           MacBookPro10,2
   Processor Name:        Intel Core i5
   Processor Speed:       2.6 GHz
   Number of Processors:           1
   Total Number of Cores:           2
   L2 Cache (per Core):   256 KB
   L3 Cache:        3 MB
   Memory:          8 GB
   Boot ROM Version:     MBP102.0106.B07
   SMC Version (system):           2.6f59
   Serial Number (system):         C02L250VFFRP
   Hardware UUID:          B26BB020-5346-5A3E-BE36-8D63AAF041C4
   Sudden Motion Sensor:
   State: Enabled
   Hard Drive APPLE SSD SD256E:
Kent Mechem

Hello Ian. I am currently using Lion installed on a WD My Passport 500Gig drive connected to my MBPro via USB, which is still running 10.6.8. Like you I am not prepared to lose all my currently functioning Mac, but also like to see how the new OS runs before making the total switch, maybe when it gets to 10.7.2
So after you download Lion and select to run the installer it will show you which disk to install on, being the default SL drive you downloaded Lion with. But here you can click Other Disk and select the external HD. The installer will run and then boot into the external drive to complete the installation. From then on you can use Startup Disk or the Option key to select the preferred OS.

Boot camp, windows xp and macbook pro-install problem

MacBook Pro 1,1
Mac OS X 10.6.8
Boot Camp Windows XP
I installed a SSD and want to put Windows XP back on the computer.
I had Windows XP running under Boot Camp on my old HDD.
During the Windows XP install when it tells you to
press ENTER to install Windows XP
press R to repair a Windows install
press F3 to exit
I can't get the install to accept any input from the keyboard.
I tried searching the discussions but I'm not finding the answer.
I'm sure it is just something simple I'm not doing. I had Windows XP
running on this MacBook Pro before.
Thanks

I wonder if your XP works with SSD or some SSDs have had trouble with Windows on Macs...
I'd search out PC forums + brand SSD for starters users with XP.
Everyone I run across though have moved on to Windows 7 64-bit.

Why does Boot Camp think I have more than one partition on my hard drive?

I'm surprised I'm finding no remedy for this problem in my searches so far. My symptom is that when I run the Boot Camp Assistant app, I get the following error message:
"The startup disk cannot be partitioned or restored to a single partition." The instructions that are provided along with the error message are: "Back up the disk and use Disk Utility to format it as a single Mac OS Extended (Journaled) volume. Restore your information to the disk and try using Boot Camp Assistant again."
When I try to follow the instructions, I see that Disk Utility shows my drive as having a single partition. Nevertheless, I've backed up my Macintosh HD volume, re-artitioned the drive into a single Mac OS Extended (Journaled) volume (once using the Snow Leopard Installation disk and once using Drive Genius 3), and restored my Macintosh HD volume. After all that, I still get the same error message. I even defragged my hard drive, which seems to have helped some users I've read about, but it hasn't helped me.
Something worth noting is that I recently upgraded to a bigger internal hard drive, and before doing so, I deleted the Boot Camp volume. I innocently thought I'd just do a fresh install sometime after replacing the hard drive, but hindsight tells me that I might have fallen victim to my own ignorance.
Is there a value stored in a register somewhere that's telling my OS that I have more than one partition when I really don't? Can someone out there help me do battle against my ignorance?
I'd be grateful for any help that can be sent my way...

Your welcome and good luck finding the solution. BTW as a newbie you benefit from:
Switch 101 & Mac 101.
Also you may want to reassess to see if you really need Windows on your computer. Remember if you install it you have all the issues every Windows users has to deal with. When I switched almost 4 years ago I installed Windows too but now I only turn it on to see if it still works. Of course your situation is different you may have proprietary software only designed for Windows and have to have it installed.

Windows Vista can't find Firefox.exe on my hard drive, but it is there. How can I get Firefox to run?

Windows Vista can't find the Firefox.exe program on my machine but it is right there in program files. Windows won't run it. After clicking on the short cut icon and after a delay I get an error message saying that windows can't find it. What can I do to fix this problem?

Hey merodi,
I dont fully understand your problem here,
1. Did your computer shut down or 'die' or did you save and then you cant find it?
2. Have you tried looking in spotlight (little magnifying glass up the corner)
3. Have you tried opening the program again? In word and pages, if the program exited forcefully, opening it again will restore the document.

Can i keep documents on a separate hard drive than Lion OS X

I have a 2011 MBP 17". On the internal spinning disk (750GB) I was running Snow Leopard. I installed a data doubler kit from OWC, taking out the optical drive and replacing it with a 120GB SSD. I then installed Lion onto that SSD and migrated my Home folder onto that drive.
On the 750 GB drive I have a Bootcamp Partition and some documents that didn't fit on the new drive.
My questions are:
1) How do I safely remove the Snow Leopard files from the original drive?
2) Can I move all of my Documents back to the larger hard drive without causing any OS problems?
Any guidance would be appreciated.

Any place where I can get a step by step instructions on how to do this? Right now there are still active users in the Snow Leopard boot disk.
What I would like to do is create a storage folder on the HDD that is an extension of my SSD User, and copy any remaining documents from the Snow Leopard user to the SSD User's folder on the HDD. Then delete all of the users on the HDD and remove the Snow Leopard files.

Please help with my Boot Camp/Windows problems

I need to install windows on to my iMac to continue a course I’m taking at uni. Sadly it’s been a nightmare so far.
I backed up all of my data and opened Boot Camp Assistant and tired to partition a section of my hard drive for windows. However it gave me an error each time I tired. After asking around I was told to buy idefrag and that should fix the problem - it didn’t. I was then told to format the hard disk and reinstall OSX. I did that and Boot Camp was now happy to partition my hard drive.
I insert a copy of legitimate copy of Windows 7 Professional (x64) and clicked the Install Windows button when Boot Camp prompted me to.
Windows installation menus open after a quick restart but quickly tells me it cant see any partitions/drives to install on.
I googled the problem read that the partition should be formatted to NTFS for windows seven to install and that OSX wont do that. I installed a free program called NTFS-3G and that formatted the partition to NTFS.
Windows now saw the drive and went through the installation process. After it has gone through its automated routine it restarts the Mac and takes me to a "Press any key to boot from CD or DVD..."
I press Enter and it takes me back to the very first installation menu and restarts the whole thing until it has once again gone through its automated routine and restarted the Mac and told me to press any key.
This happened ever time. During the install I am presented with the options of "Installing Windows" or "repairing windows". When I tried the automatic repair it told me it could find no fault.
So I started again by deleting the partition from within OSX and making a new one and installing windows and restarting but this time remove the windows 7 disk.
All this did was boot the Mac up in OSX. I then restarted the Mac and held down the options key. This presented me with the choice of booting from the Mac HDD or the windows partition. I chose the windows partition and it takes me to a black screen with a flashing line/prompt and does nothing else.
I assumed Windows 7 might not like my Mac for some strange reason so brought a copy of Vista business with SP2 (x86).
I deleting the partition from within OSX and made a new one. I began installing Vista. It told me it could only install on NTFS formatted partitions/drives.
Once again I used NTFS-3G to formatted the partition to NTFS and relaunced vista.
It installed fine and restarted itself. Once again it took me back to the first installation screen just as windows 7 did. I tried restarting without the disk (hold options again) and it took me back to the black screen with the flashing line and sat there forever.
I restarted the Mac with the OSX 10.6.1 install disk in the drive and it booted up ignoring the disk. I launched the disk from desk top and looked through the install options hoping to find some drivers or extra installs for boot camp/windows. I couldn’t see anything.
I don’t know what else to try.
I have a 21.5' iMac:
Model Name: iMac
Model Identifier: iMac10,1
Processor Name: Intel Core 2 Duo
Processor Speed: 3.06 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 3 MB
Memory: 4 GB
Bus Speed: 1.07 GHz
Boot ROM Version: IM101.00CC.B00
SMC Version (system): 1.52f9

Re-read in the PDF guide in Boot Camp Assist where it tells you to format the "BOOTCAMP" FAT volume when in Windows.
http://www.apple.com/support/bootcamp
But I have really only one question:
Was this an electronic school download edition? they offer students Windows 7 Pro. If this was an electronic version from school, fine, but it has to be burned at *reduced 2x speed* or it won't work, and can have various (and different for everyone) problems, BUT: it is pretty well known and semi "documented."
You do NOT need NTFS driver. That is totally wrong.
Sorry you bought Vista, I used it but once Windows 7 went Beta and then RC I've used 7 and never looked back (what Vista should/could have been but was not, even with SP2).

Remove Boot Camp Windows Partition

I would like to know how to remove the Boot Camp windows partion all together from my computer.

When I try to use the Boot Camp Assistant it does not give me the option of removing it.

Can't Install Windows in Boot Camp - Windows Driver Issue

Before update to Mavericks, I had an installation of WIndows 7 running in Bootcamp. I had updated this to Windows 8.
Just prior to Mavericks release, the hard drive in my MacBook Pro started to fail. I had a full backup of the OS X partitiion, but did not have one of Windows.
After the drive was replaced, I did a fresh install of Mavericks and I'm planning on doing new installs of my apps over the coming days. (It's an opportunity to clear-out remains of old apps/OS's.) I have hit a wall with Boot Camp, though:
I used the Boot Camp Assistant to download the driver sets ("Windows support software") to a USB stick and partition the HD. However, although the Mac then boots off the Windows 8 (64-bit) installer DVD I can only get as far as choosing the installation language before I get stuck on the next step where it's looking for missing drivers. At first, I thought this was some reference to the ones downloaded from Apple, but I am now pretty certain that these just get installed after [in] Windows to allow access to the Apple hardware.
I have tried installing Windows 7 and get hung-up at the same point (which did not happen on 10.8).
Does anyone have any insight into what's happening and how I can get around the problem please?

Just chiming in - having the same issue as Bernard and Ian here myself, but with Windows 7 Ultimate 64 bit. Trying to install on MBP Late 2013, Mavericks, using USB. I get through the bootcamp phase to the language selection in Windows and then get the drivers error message.
Called apple tech support and they indicated that OEMs can sometimes be lightweight versions of the DVD installers (i.e. they leave out certain drivers because they assume a certain set of hardware components will be present, typically hardware that perhaps only PCs have and Macs don't) - so they suggested trying to get my hands on a retail version of the ISO file that might have all of the drivers necessary. I tried downloading every feasible iteration of the windows trial ISOs here but every one of them gave me the same error message in Windows setup. My next step is to call microsoft to ask them for a "complete" ISO - I'm hoping they can cooperate since I do have a valid, un-used authentication code for my Windows product. I'll let you know if this works.
In the meantime - has anyone found an easier fix?

Can I upgrade to Mountain Lion with Boot Camp windows 7?

Can I upgrade my mac book pro to Mountain Lion when I have Boot Camp Windows 7?

Welcome to the Apple Support Communities
You can upgrade to Mountain Lion without any problem, but I recommend you to make a backup before upgrading. Also, after upgrading OS X, I recommend you to download the most recent Boot Camp drivers on Boot Camp Assistant and install the drivers on Windows

Is my (Boot Camp) windows partition safe after installing OS X Lion ?

I work with a mac and i have an Windows partition only to work at home for my company (i do not keep documents of photo's there).
I want to install OS X Lion, but i am affraid that my windows partition will be gone after installing OS X Lion.
Apple support can not guarantee that my partition wil be safe.
I dont have data saved in my Windows partition. I have this partition just to work from home, so the data is not the issue.
I want to know that my partition wil be safe after installing OS X Lion, because i do not know how to make a new partition.
What can i do to keep my Boot Camp partition up and running after installing OS X Lion ?
Who can help ?

I also was concerned about the early reports of 10.7 altering the Boot Camp partition id. I took The hatters advice and used the cloning method on two different MBPs (Vista & Win 7) with no problems at all.
FYI, below I have provided the steps I used to accomplish this process.
Use Yasu and Diskwarrior to prepare the existing Mac OSX 10.6.8 HDD partition.
Clone or update by smart clone to an ext HDD with SuperDuper or Carbon Copy Cloner.
Restart from the cloned ext HDD and select it as the startup volume via System Preferences / Startup Disk.
Install 10.7 Lion on the cloned ext HDD
Install Lion 10.7.2 update on the ext HDD
Restart the OSX 10.7 ext HDD and test and adjust the preferences if needed.
When satisfied, clone the OSX 10.7 ext HDD back to the existing Mac HDD.
The Boot Camp partition will not be altered as to drive id which appeared to cause problems for a few people.
The recovery partition will be on the ext HDD and can be used for trouble shooting.
A more convenient way to have the recovery/reinstallation environment is to create a Lion install USB thumb drive.
http://osxdaily.com/2011/07/08/make-a-bootable-mac-os-x-10-7-lion-installer-from -a-usb-flash-drive/
http://subrosasoft.com/blog/2011/07/create-a-bootable-mac-os-x-10-7-lion-flash-d rive/

I have a MacBook 10.5.8 with Boot Camp. I can only operate the Windows side. When I move into MacOS it does not open.

I have a MacBook 10.5.8 with Boot Camp. I can only operate the Windows side. When I move into MacOS it does not open.

Your phrasing is not clear. How do you reboot into Mac OS? /can you describe the process step by step?
Usually, you should do like this:
- while in win, restart
- immediately after chime, press option or alt key
- wait for 2-3 seconds, you should see the boot options
- select Mac OS partition
If you have performed all these steps, and, after choosing Mac OS partition, you cannot boot into Mac OS, then your system is corrupt and should be reinstalled.

Installing boot camp/windows on separate drive (Tiger) question

I work in a college computer lab where we have been instructed to install an additional internal hard drive on our lab of Mac Pros which will be dedicated to Windows.
The issue that I see is that we are still running Tiger due to some of the specialized software that we use not being compatible with Leopard and will not be upgrading the OS for at least a semester. I have read that Boot Camp is no longer compatible with Tiger, so my question is this: Is it possible to still install the drives which will be windows formatted if we have a copy of the old Boot Camp Beta (which I understand is no longer available)? I would think this is not particularly wise to do, but unfortunately I am not the final say in my situation.
Thanks for your help on this!

maestrotim wrote:
Thanks Stefan, sorry but what drivers CD do you mean?
With the Beta the neede Windows Drivers are incorporated into the BootCamp Assistant.
Since you need the drivers to complete the Windows Installation, you have to make a Drivers CD from the BootCamp Assistant before starting the Windows Installation.
In the Top Menu of the Assistant you find this.
Regards
Stefan

Boot Camp Windows 7 No Longer Connects to Internet

Hello, I have a mid 2011 iMac with Boot Camp Windows 7 installation. It has run flawlessly for more than a year. Recently however, I have been untable to connect to internet when running Windows. The connection works fine as a Mac. While in Windows, I can momentarily (about 10 seconds) connect by disconnecting and reconnecting the LAN cable. Then the "no internet." I have all the latest Boot Camp support software installed. All MAC and Windows software updates are installed. My network devices are configured correctly. I have rolled back to previous Windows updates with no resolution. Does anyone have any suggestions?

your router, your Windows firewall, you are using something other than Windows Defender (8) or Essentials (7), something else on the cable.
you had a storm and the modem is on life support and your ISP can login and see what errors the modem is showing, you don't have network surge protection (APC tend to interfere, Cyberpower tend to work).
What else is on the LAN?
I found Windows to be funny about network but 8 and 8.1 have never had trouble. With 7 I sometimes had to reboot.
Besides Apple and Windows, some drivers are or often still needed - manually.

HT201541 Mac mini Late 2014 Boot Camp Windows 7 sound issue

Hi,
I'm wondering if anyone can help me with my Mac mini (Late 2014) and Boot Camp (Windows 7). The problem I'm having is that there's no audio when I boot into Windows 7, though everything works fine under OS X. After installing Boot Camp and Windows, the audio worked perfectly up until yesterday, and now there's nothing. I've tried updating as well as uninstalling and reinstalling drivers, but this hasn't helped at all.
When I open Volume Mixer and Playback Devices, the sliders show that audio is playing, but I hear nothing - either from the built-in speaker or when I headphones.
The Device Status indicates that "This device is working properly" and that the drivers are up to date. Tthe following drivers are installed:
dmk.sys
HdAudio.sys
ksthunk.sys
portcls.sys
SysFxUI.dll
WMALFXGFXDSP.dll
Has anyone else encountered this issue, or does anyone have any tips on how I might fix this?

Is the volume Muted? The Mac has an Audio database of devices and volumes in NVRAM, so an SMC Reset or PRAM reset might help. Please see this link for appropriate keys Startup key combinations for Intel-based Macs - Apple Support.

Boot Camp / Windows Partion... Can it be installed on a separate hard drive

Similar Messages

Maybe you are looking for