Boot from mSATA drive on HP ENVY 15t-j100

I purchased an HP ENVY 15t-j100 with a 1TB drive and 16GB RAM.  There is an avaialble mSATA slot in the user area so I purchased a CRUCIAL 240Gb mSATA drive with the intention of installing the WIN 8.1 OS and my programs on the solid state drive and use the slor (5400) hard drive for data.
I used the Recovery drive I created to get the OS on the mSATA - no problem.
It even boots up - but when I install the hard direve the system tries to boot from the spining drive - the BIOS shows that the Hard dirve is "in" Port 0 and the mSATA is Port 1 and there does not seem to be any what to change this so, after all the work and research it dies not seem like I can utilize the mSATA slot on this notebook.
Any ideas would be greatly apprecaited.

HLubert wrote:
I purchased an HP ENVY 15t-j100 with a 1TB drive and 16GB RAM.  There is an avaialble mSATA slot in the user area so I purchased a CRUCIAL 240Gb mSATA drive with the intention of installing the WIN 8.1 OS and my programs on the solid state drive and use the slor (5400) hard drive for data.
I used the Recovery drive I created to get the OS on the mSATA - no problem.
It even boots up - but when I install the hard direve the system tries to boot from the spining drive - the BIOS shows that the Hard dirve is "in" Port 0 and the mSATA is Port 1 and there does not seem to be any what to change this so, after all the work and research it dies not seem like I can utilize the mSATA slot on this notebook.
Any ideas would be greatly apprecaited.
I have solved it by installing a third party bootloader on the main hard drive. The hard drive must be connected via USB to a computer (even the same laptop with the mSATA in as I did). I have used Bootice to install a bootloader called Plop .
http://www.pendriveapps.com/bootice-partition-flash-drive-edit-boot-sector/
Then put the hard drive back in and set the mSATA in Plop as the boot drive. Here is some info:
http://www.plop.at/en/bootmanager/thebootmanager.html#b4
I couldn't make it work but then I went to "Profiles" - "Linked partitions", picked the right partition, confirmed it and it worked.  However, I don't have the laptop anymore and can't say exactly what to do.
Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
Testing - HP 15-p000
HP Touchpad provided by HP
Currently on Debian Wheeze
*Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

Similar Messages

  • Why HP remove support for msata drives in the ENVY 15t - q100 ?

    The previous models had msata support, but the ENVY 15t - q100 (the one with no dvd drive) has the space for a msata drive, even with the screw hole but they remove the slot from the board. This is a $900 laptop, why they did that?

    @Emanu526 ,
    Hello and thank you for posting on the HP support forums.  So that we can best support your issue please post back with the full model and product number.
    HP Notebook PCs - How Do I Find My Model Number or Product Number?
    As well please check out the following link before posting back.
    Advice for asking the "Very Best Question"
    As for changes in BIOS or configuration I am unable to comment on that.  Each model is created based on a constantly changing market requirement and the engineers and design people would be the only ones that can answer that question.
    Thank you again for posting and have a great day.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • NOT as a cache, can i boot Windows 8 directly from MSATA 128gb on an Envy 4 1026tu..?

    Can i install & boot Windows 8 directly from MSATA 128gb on an Envy 4 1026tu..? Not as a cache. I want to keep my existing HDD as extra storage. Can i clean install Windows 8 and boot directly from a 128gb MSATA on my Envy 4 1026tu?  Could anyone please advise me if this could be done. Thanks!

    Hi,
    In theory nothing can stop you to do that. You have to disable the HDD before install OS on the mSATA. One important thing: The BIOS allows you to do that. I know Dell people have done that. At the mean time, the following article may help:
       http://blog.laptopmag.com/triple-your-speed-how-to-install-an-msata-ssd-boot-drive-in-your-laptop
    Good luck.
    ps My HP machine has only 32Gb and inaccessible. 
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • My iMac (late 2006) no longer boots from FireWire drives, although they contain all the system files.

    My iMac (late 2006) no longer starts (boots) from Firewire drives, although they all contain a current system (Mac OS X 10.6.7). If the drives are connected with USB 2, they boot normally. The FireWire drives appear in the Start Volume program, but they do not boot. If I press and hold the Alt key while booting, only the internal drives and the USB drives appear as options. What can I do in order to boot from FireWire drives as I always could in the past?

    I'd first recommend doing a SMC reset and if that doesn't work refer to:
    http://reviews.cnet.com/8301-13727_7-10333969-263.html
    and
    http://www.thexlab.com/faqs/firewiretroubleshooting.html
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    Roger

  • Problems booting from external drives

    Ever since I got this 6-core 2013 MacPro (January 2015), I have had strange problems and glitches, but for this posting, I am talking about problems being able to boot up from external drives. I took the 4 external drives out of my old 2009 MacPro and put them into a 4-bay Thunderbolt enclosure. This enclosure can be configured as a RAID if all drives are the same (which they are not) or it can just be a place to be able to access all 4 drives. I used to be able to boot from each of those drives on the older MacPro but I am unable to do so now. They show up in the System Preferences/Startup Disk but if I choose one, it just reboots into the new MacPro drive. I even tried pulling out a couple of the drives and mounting each into a USB 3.0 (Sabrent) dock and still I could not boot from those drives which have the latest version of Yosemite. Yes, they are formatted correctly. I used to boot from them. I was able to clone one of the drives to a Seagate USB 3.0 hard drive and boot from that. Although, the clone was not perfect. It didn't transfer all my settings so I could recover some logins and serial numbers I wanted that I have never been able to retrieve since I got this new Mac.
    Yesterday, I formatted a 32GB flash drive and tried to install Yosemite on it. I planned to put DiskWarrior on it. When I started to install Yosemite (from a saved download) it let me choose that drive, but when it restarted before installing, I was right back where I started on my MacPro's hard drive.
    Is this normal behavior for the 2013 MacPro? Or is it just mine? I am beginning to think I may have a lemon since I have had other strange problems that don't go away.

    Not all external devices are bootable. First stop would be involve whoever handles the 4-bay Thunderbolt. Seeing how it has a bridge most likely in order to support RAID mode that may not have the correct frmware or other reasons.
    https://bombich.com/kb/ccc4
    https://bombich.com/kb/ccc4/search/bootable%20volume
    CCC is the only program I would be using.

  • XServe won't boot from any drive, but recognizes them in OS X Installer

    I know I have another post here but this is a different issue, and I've already fixed that one thanks to Camelot .
    I just received an 2 used xserves for work. One booted into OS X Server fine, so I scrubbed it and reinstalled without issue.
    The second however never booted into an install. That is, I never found it on my network when I started it up and when I pushed the power button it would turn off immediately, suggesting that there was no OS on the disk or that the xserve couldn't find it. I didn't have a spare monitor to plug into it (surprisingly) so I just chalked it up to the fact that it was a new disk and hadn't had OS X Server installed on it.
    Now I have a spare monitor, I've gone and installed OS X Server on the xserve. It boots from the DVD just fine, runs through the installer, then when it goes to restart, it won't boot from the hard drive that it just installed OS X Server on, it'll just boot back from the DVD unless I pop it out. If I let it boot up without the DVD in it, I'll get the standard Folder with a ?.
    At first I thought it was the drive, so I installed OS X Server on another drive. Still wouldn't boot to that drive, so I booted from the DVD and repaired the disks in Disk Utility. Still nothing. I booted to DVD again and when I went to Startup Disk, it actually did show my disks with their respective OS X Server installs.
    When I boot the machine holding alt/option, the system doesn't show my drives, only the DVD if it's in the slot.
    I figured ok, this has to be the drives, so I swapped them with those of the identical xserve in the rack below, but my top xserve wouldn't boot from those drives either. Somewhat expectedly however, the bottom xserve would boot the drives that I took out of the first one.
    Now I'm just stumped. Any ideas?
    PS, drives are unlocked.

    MrHoffman wrote:
    The EFI firmware, the SMC and possibly the disk I/O path seem good potential candidates for culprit.
    Load and run the hardware diagnostics.
    Reset the SMC, and reset the LOM.
    I'm running the EFI diagnostic tool now. Firmware and disk I/O path came to mind, let's just hope it's not a major hardware issue
    beatle20359 wrote:
    Hi Jeff,
    Do you have the specs of the xserve and the version of OSX server you are trying to install? Does the Xserve have the RAID card installed in it and what size are the drive modules.
    All the best
    Beatle
    2x 3GHz Dual-Core Xeon
    8GB RAM
    OS X Server v 10.6.3 (the version I'm trying to install, that is)
    No RAID card. The system drive is 80GB and a second storage drive is 1TB.

  • Satellite P300-1A8 will not boot from disc drive

    Hi,
    I had a little play with start up programs, partitioning the hard drive and marking as active and deleting programs i thought i did not need.
    I obviously had no idea what i was doing!
    Laptop will go to toshiba screen then goes blank, i can not boot from the disc drive.
    I put the hard drive into another laptop and it works fine.
    I put the hard drive of that laptop in the buggered one and that works fine.
    How the hell do i put the original one back with it working??
    Really really stuck with this!!!!!
    Any help would be appreciated.
    Only thing i havent tried is the recovery disc but im not paying for one if it wont boot as itl be a waste of money.
    Seems like its a compatability problem with cpu and hard drive as they dont want to be friends anymore!!
    Thank you in advance

    Hi!
    Can you boot in the safe mode?
    If you dont have a recovery disk, use the Microsoft installation disk and try to boot from it.
    And you said that you cant boot from disc drive, did you tried different disks?
    Maybe some are not readable or not bootable.
    The best way would be a recovery disk. The installation takes a few minutes and you have a clean installation with all drivers and tools from Toshiba.
    Bye

  • MacPro can't boot from external drive

    Running 10.7.3 and a MacPro which gets backed up each night with SuperDuper. Can't boot from this drive (black screen). Yet I can take the same drive and start up my Macbook Pro! So it isn't the drive or the data on it. I'm stumped. Could this be related to an issue where I can't get this same MacPro or system to successfully backup to Time Machine without error? The boot drive seems OK (ran Disk Warrior and Disk Utility).

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. The instructions provided by Apple are as follows:
    Be sure your Mac is shut down.
    Press the power button.
    Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
    Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem(s)?
    After testing, reboot as usual (i.e., not in safe mode.)

  • Can't boot from internal drive - Please help!

    The internal drive on my PBG4 was making some funny noises this morning and sure enough, when I tried to reboot from it I was unable to. Instead I was brought to a screen with a DOS prompt with some cryptic error message. Since then I've called Apple support and their "solution" was to re-format the drive and reinstall the OS. I can do that if I absolutely have to, but if there's any way around it, I'd much rather avoid the reformatting/reinstalling everything nightmare scenario. Initially Disk Repair said the drive couldn't be repaired. I booted from my Disk Warrior CD (3.0.3), which prompted me to backup data (luckily I have an external 250GB drive) and I backed up my home directory. I did that and rebuilt the directory, then restarted from my Tiger CD and ran Disk utility again and it said the disk was fine. I tried to boot from the drive and I get taken to a DOS prompt again with the following error message:
    launchd can't exec /bin/sh for single user: No such file or directory
    Any suggestions on what I can try at this point short of reformatting the drive and starting over from scratch?
    Powerbook G4   Mac OS X (10.4.7)   1.25 GHZ, 1GB Ram
    Powerbook G4   Mac OS X (10.4.5)   1.25 GHZ, 1GB Ram

    I assume you have OS X on a 2nd drive that you can run DW, Disk Utility etc.
    As you backup files and know they are okay, delete them. Undo the layers of onion and try to go from latest to oldest.
    If you don't have an emergency fw drive...
    The trouble with long backups on a problem drive is they can fail during the backup if the drive gets too hot, which happens.
    Back in Panther, you could use BootCD to create an emergency CD or DVD with your system, full finder, loads of utilities, and could even run FireFox. With that, you could run TTPro 4, Disk Warrior, DU, Rember etc. AND play around in the Finder and Terminal.
    I still keep a CD and DVD with 10.3.9 just in case. The perfect FW drive would have a couple OS versions, a backup partition (that you can erase if needed).
    Apple Disk Utility from CD/DVD can also be used to copy/clone a volume or foleer, using Restore and output to a volume or disk image.

  • Cannot boot from USB drive!!!!!!!!!!!!!

    Hi
    I have 3-4 120Gb 2.5inch drives which I clone my MacBook Pro to on rotation.
    I have always been able to boot from these drives UNTIL NOW!
    Suddenly I can no longer boot from them, the boot process starts and gets well through and then the drives all seem to just 'hang'.
    The only significant change is that a local Apple support company upgraded my stock 120gb drive to a 160Gb drive.
    Any ideas what the issue coiuld be?
    Cheers.
    Robin

    Hi robster,
    If the USB drive contains a valid OS you should be able to verify and repair the permissions on that drive, give that a try.
    Also i suggest running DiskWarrior 4 on it.
    The replaced internal drive should have no effect on this unless some settings got changed when the new OS got installed on it that now prevents the mac from being able to read your USB drive.
    Does the USB drive need a driver ? if so is the latest version of that driver properly installed ?
    If the USB drive checks out and all is OK maybe a re-install of the OS on your internal drive would help.
    For now try disk utility and diskwarrior if you can that could narrow things down

  • Is it possible boot from U drive?

    Is it possible boot from U drive on a leopard system? How to do it? My CD disc was broke, and i try to install a windows Xp by bootcamp,but i cannot boot from CD anymore.

    *"No flashdrive boot option."*
    Then the Mac doesn't see the flash drive as a bootable volume.
    If there is another way to install Windows without an optical drive you'd be better off posting your question in the Boot Camp forums, as if anyone has done it, you'd find them there:
    http://discussions.apple.com/category.jspa?categoryID=237

  • DV7-6185us wont boot from hard drive.

    I recently installed a new hard drive after the one it came with completely crashed. After installation of new hard drives, I inserted and installed all of the recovery disks needed for the new hard drive. Upon completetion it said it needed a restart and after restart I get a message saying I need a OS for the hard drive for boot up.
    I went into my bios to make sure the hard drive was first in boot order which it is but when trying to pick where to put from on the bios screen it only give me the cd option. I ran a full diagnostic of the hard drive and everything checks out. I made sure to unplus the hard drive and tried a different slot and still get the same thing. Installation when fine but still won't boot from hard drive.
    Is there something that i'm missing? The hard drive is fine. So what could it be?

    Hi,
    Assuming this is just a problem with the recovery media, here's an alternative option you could try.
    Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
    An example of a COA Label can be seen Here.
    You can create a Windows 7 installation disc yourself using another PC - just download the correct Disc Image ( this must be the same version that originally came with your notebook - this is listed as Windows 7 Home Premium ) from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here.  These Images are clean and from a well-respected source - Digital River.
    Windows 7 Images.
    Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
    http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
    Any additional drivers and software you may need can be found Here.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • V120 server boot from hard drive freezes

    Hi
    I just installed open solaris build 75 on a sun v120 server. After the instalation all went well and I configured the processes and users on the server just like I did yesterday on another v120. What i did afterwards that was different from yesterday is that I put the machine on standby by holding the power off (0) switch for a few seconds, then unpluged the power chord. After turning the power on again the server will freeze the boot process in the first 2 steps after it tries booting from hard drive. (It does pass all hardware checks). To comunicate with the server I connect a windows PC on the lom port with serial cable and the SecureCRT software. I tried to break into lom with #. after poweron but it doesn't seem to work. And the lom console in standby wont let me boot from cdrom or anything while in standby. Can anyone give me some guidance here? I don't have much experience with this kind of hardware.

    Well, LOL,  I did that prior to buying the software. It does meet the specifications. I found the solution on the support site. When I googled before I hadn't googled the error message verbatim. Doing so led me to this page: http://support.apple.com/kb/TS3926 where I was instructed to create a tiny partition (128MB) and then run the installer again. No explanation was given as to why, but this did work and I am typing this via the new OS. Thanks for trying to help me baltwo! Best regards.

  • Help diagnos. flashing question mark on monitor, cannot boot from CD drive

    Any ideas? This is an older G3 tower which was "souped Up" wtih USB and Firewire cards, memory
    Mac froze in midst of work last week. Now only get flashing question mark supermimposed on image of a floppy drive.
    Tried to re install system (OS9) but cannot get ANY CD to boot from CD drive. I reboot, hold down "C" Key with CD in tray ( and i can hear the CD drive working). But the tray opens and ejects/rejects the CD).
    I now suspect the problem is NOT the OS but rather a hardware issue.
    Am I correct in this assumption? what else could this be?
    I am trying to help an older gentleman who has no backups and has some important documents on the HD.If I can boot up, might be able to retrieve those itesm. (and get a newer Mac!)

    Not the answer,Dale (thanks anyway)
    I read that article.
    I cannot boot from any bootable CD.
    Inserted the OS install disk as well as third party bootable CD.
    with CD in the CD drive tray, I restarted and held down the C key.
    Mac restarted but the CD tray popped open. Would not boot from the CD.
    That is why I posted query
    not only do we have the flashing question mark but bootable CDs are not booting this Mac. So I can do no diagnostics, no repair, not salvage of files.
    I am trying to understand where the problem lies. am guessing Hard Drive failure but why should CD also not work?

  • Cannot boot from ext drive after 10.5.2 update

    I followed the procedure in tech article 306502 for creating and updating a bootable drive. I am in a PPC Mini environment. External drive is LaCie 160 GB rugged firewire portable with auxiliary power, I created the drive with 10.5.1 and it booted nicely to my two Minis (running 10.3.9 and 10.5.1). I then updated the external system with 10.5.2 from the Apple site and now it does not boot. Sits and spins with a white screen, grey apple, and whirligig. Whirled for 1/2 hour and tried deveral times.
    I see this is not uncommon, but there have been no cures posted. One post suggested Disk Warrior. What would I do to with DW to move this problem forward. This is quite annoying, as I rely on being able to move around and boot from this drive when needed.
    Thanks for any help.
    Fred

    after 10.5.2 two days ago, mine booted up regularly. however after the additional leopard graphics update last night, it no longer boots up at all. i have to usethis ****** vista to report the problem. my macbook is right beside me, with nothing but a plain blue screen. occasionaly the mouse cursor appears for about 30 seconds, then dissapears and the screen remains blue. what can i do? if i cant log in apple cant update my mac!!! help!!!

Maybe you are looking for