Boot Loader upgrade query
Hi All,
I've upgraded a 3750 integrated controller and a 4402 to 5.0.148.0 (s/w and bootloader image) but the sh sysinfo ouput still reports the previous bootloader version:
Product Version........... 5.0.148.0
RTOS Version..... Linux-2.6.10_mvl401
Bootloader Version.......... 4.2.61.0
Have I missed a step, or is there some other problem?
Thanks for any help
Scott
Hi Dennis,
I upgraded the 3750 first - uploaded both images, disabled the WLANs and rebooted the box. Checked the sysinfo and saw the discrepancy - tried downloding the ER file again and rebooted but no difference.
With the 4402 I rebooted after downloading the s/w then repeated with the boot image - Same result - bootloader still previous version. This time I forgot to disable the WLANs though.
The run-config output reports the 4.2 bootloader.
I did notice that when I was upgrading the 4402 via it's own GUI it was referring to the "emergency bootloader", could this be significant?
Thanks
Scott
Similar Messages
-
SQL Dev 2.1:Ability to save and load visual query models?
At SQL Dev 2.1, do we now have the ability to save and load visual query models as with TOAD? Or has that functionality been rolled into the for-pay Data Modeler extension? Seemed strange to hide the functionality deep within SQL Worksheet, then not allow query models to be saved or loaded. From what I recall, load/save was scheduled to be in 2.0.
I've not yet downloaded and installed 2.1, but also as I recall, it was promised to be a significant (e.g. new-feature rich) release. Has it lived up to that promise? Hoping also that it's not so buggy as to not merit an upgrade. At my workplace, folks have different versions of SQL Dev 1.X installed, each for the purpose of retaining functionality that got broken in future releases, etc. Would love to be able to advise them to retire their 1.X installs in favor of 2.1.
Edited by: Dana N on Jan 21, 2010 6:45 AMDana, We are working on the query builder. We have not done anything with it in recent releases as we knew that it needed completely overhauled and a
couple of bug fixes were not going to give us the query builder we needed. Sue will be able to tell you more as the we get closer to releasing it as a feature.Thanks Barry. I know it's probably impossible to give firm dates, but my colleagues would love to know, ballpark, when query builder might be ready. Any particular year/quarter that's targeted for?
A lot of the bugs in the 2.1 are probably my fault as we decided to build a framework which allowed tasks to be scheduled like eclipse and push them to the
background. Coupled with this, we tore apart the worksheet to allow us to fit tasks in, but to also give us the ability to do some of the enhancement requests
that you guys, our users, have been asking for. While its not perfect, I believe its getting much better from both a functionality and performance standpoint. The
worksheet will not change again and there are no enhancements logged or scheduled which will do that. The issues that have come as part of 2.1 are being
addressed and we are fixing the highest priority ones as we speak. One of my priorities is to make these components as rock solid as possible.Thanks again. It really is a nice tool to work with, and I'm grateful to have it. I would choose stability for existing features over new ones, but I suppose there always has to be a balance in development. What was really scary in the past was getting bizarre / wrong answers in query results--that's a complete show stopper; e.g. clicking on a row/col intersection in a result set row would show strange and false values. New features can wait, but core functionality must be solid. If one can't presume integrity of query results, it's game over--using a version of SQL Developer that returns inconsistent result sets between runs could be Considered Harmful, or so it is to me.
Anyway, thanks for responding and I hope Oracle Corp gets you whatever assistance you need to improve the quality of existing functionality while adding new features; with one not being at the expense of the other. :-) Glad also to see Sue has authored a book on the tool. Hopefully that will drive customer demand and force increased allocation of development resources toward the product. I'd like to think having out-of-the-box tools that are a joy to use might even increase market share.
Data Modeler I would love to use, but am completely priced out of it. Enterprise Architect from Sparx Systems is the best value there so far as I can tell.
Dana -
Nexus7000 Boot issue " Status 90: Loading Boot Loader "
Hi Gents,
I have currently upgraded a NX7k to NX-OS 5.0.2 .
Now I am stuck by rebooting the system (check output below)
No chang after a manual power off and on the System.
Does anybody know how to get out of this boot process ?
Thanks in advanced for your feedback
Saluti
Alibani
<< console output >>
This command will reboot the system. (y/n)? [n] y
2010 Jun 2 09:10:20 FOR110R050_Labor %$ VDC-1 %$ %PLATFORM-2-PFM_SYSTEM_RESET: Manual system restart from Command Line Interface
writing reset reason 9,
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot Loader
Status 90: Loading Boot LoaderHi Wilhelm,
I have tried your advice and it works, my Nexus come back life again
Thanks mate.
best regards,
Yedi -
Xen / pygrub issues: VmError: Boot loader didn't return any data!
Hardware:
2x Intel Xeon Quad-Core 2.33GHz
24GB FBDIMM RAM
2x 2TB HDD in RAID-1
Intel Server Board S5400SF
Setup:
Arch Linux x86_64
Xen 4.1.2
Grub2 Multiboot
Synopsis:
I set up a new VM for Debian Squeeze following instructions here: http://www.howtoforge.com/installing-de … 86_64-dom0. Partitioning & installation completed correctly. When I tried to run the VPS afterwards, I got this output:
| [root@srv0 xen]# xm create -c /etc/xen/xm-debian.cfg
| Using config file "/etc/xen/xm-debian.cfg".
| Error: Boot loader didn't return any data!
I've attached a more complete log output at the end of the mail.
This is the first VM I have tried to create on this setup.
Additional:
I can mount the partition within the lvm:
| [root@srv0 xen]# kpartx -av /dev/VPS/fennec
| add map VPS-fennec1 (253:2): 0 83881984 linear /dev/VPS/fennec 2048
| [root@srv0 xen]# mount /dev/mapper/VPS-fennec1 /mnt
| [root@srv0 xen]# cd /mnt
| [root@srv0 mnt]# ls
| bin etc lib lost+found opt sbin sys var
| boot home lib32 media proc selinux tmp vmlinuz
| dev initrd.img lib64 mnt root srv usr
| [root@srv0 mnt]# cd boot
| [root@srv0 boot]# ls
| config-2.6.32-5-amd64 initrd.img-2.6.32-5-amd64 vmlinuz-2.6.32-5-amd64
| grub System.map-2.6.32-5-amd64
| initrd vmlinuz
| [root@srv0 boot]# cd grub
| [root@srv0 grub]# cat menu.lst
| timeout 5
| default 0
|
| title Linux
| kernel /boot/vmlinuz root=/dev/xvda1
| initrd /boot/initrd
As you can see, the kernel (which is 2.6.32) and vmlinuz (also 2.6.32) exist in the /boot directory.
Pygrub:
Attempting to pygrub the VPS LVM gives the following output:
| [root@srv0 /]# pygrub --kernel=/boot/vmlinuz --ramdisk=/boot/initrd /dev/VPS/fennec
| Traceback (most recent call last):
| File "/usr/bin/pygrub", line 774, in <module>
| raise RuntimeError, "Unable to find partition containing kernel"
| RuntimeError: Unable to find partition containing kernel
domU Config File:
| name = "fennec"
| memory = 1024
| maxmem = 1024
| cpus = "2-7"
| disk = [
| 'phy:/dev/VPS/fennec,xvda,w',
| 'phy:/dev/VPS/fennec-swap,xvdb,w'
| ]
| vif = ['']
| bootloader = "pygrub"
| bootargs = "--kernel=/boot/vmlinuz --ramdisk=/boot/initrd"
I have tried this with and without the bootargs line without any success.
About The Filesystem:
/dev/VPS is a vg on a RAID-1 array
/dev/VPS/fennec is an lv on VPS vg
The fennec lv has a single ext3 partition of 40GB
xend.log Output:
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:103) XendDomainInfo.create(['vm', ['name', 'fennec'], ['memory', 1024], ['maxmem', 1024], ['on_xend_start', 'ignore'], ['on_xend_stop', 'ignore'], ['vcpus', 1], ['cpus', '2-7'], ['oos', 1], ['bootloader', '/usr/bin/pygrub'], ['bootloader_args', '--kernel=/boot/vmlinuz --ramdisk=/boot/initrd'], ['image', ['linux', ['videoram', 4], ['tsc_mode', 0], ['nomigrate', 0]]], ['s3_integrity', 1], ['device', ['vbd', ['uname', 'phy:/dev/VPS/fennec'], ['dev', 'xvda'], ['mode', 'w']]], ['device', ['vbd', ['uname', 'phy:/dev/VPS/fennec-swap'], ['dev', 'xvdb'], ['mode', 'w']]], ['device', ['vif']]])
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:2498) XendDomainInfo.constructDomain
[2012-07-20 09:35:17 907] DEBUG (balloon:187) Balloon: 22794808 KiB free; need 16384; done.
[2012-07-20 09:35:17 907] DEBUG (XendDomain:476) Adding Domain: 17
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:2836) XendDomainInfo.initDomain: 17 256
[2012-07-20 09:35:17 25157] DEBUG (XendBootloader:113) Launching bootloader as ['/usr/bin/pygrub', '--output=/var/run/xend/boot/xenbl.15844', '--kernel=/boot/vmlinuz', '--ramdisk=/boot/initrd', '/dev/VPS/fennec'].
[2012-07-20 09:35:17 907] ERROR (XendBootloader:214) Boot loader didn't return any data!
[2012-07-20 09:35:17 907] ERROR (XendDomainInfo:488) VM start failed
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 474, in start
XendTask.log_progress(31, 60, self._initDomain)
File "/usr/lib/python2.7/site-packages/xen/xend/XendTask.py", line 209, in log_progress
retval = func(*args, **kwds)
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 2838, in _initDomain
self._configureBootloader()
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 3285, in _configureBootloader
bootloader_args, kernel, ramdisk, args)
File "/usr/lib/python2.7/site-packages/xen/xend/XendBootloader.py", line 215, in bootloader
raise VmError, msg
VmError: Boot loader didn't return any data!
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:3071) XendDomainInfo.destroy: domid=17
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:2406) No device model
[2012-07-20 09:35:17 907] DEBUG (XendDomainInfo:2408) Releasing devices
[2012-07-20 09:35:17 907] ERROR (XendDomainInfo:108) Domain construction failed
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 106, in create
vm.start()
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 474, in start
XendTask.log_progress(31, 60, self._initDomain)
File "/usr/lib/python2.7/site-packages/xen/xend/XendTask.py", line 209, in log_progress
retval = func(*args, **kwds)
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 2838, in _initDomain
self._configureBootloader()
File "/usr/lib/python2.7/site-packages/xen/xend/XendDomainInfo.py", line 3285, in _configureBootloader
bootloader_args, kernel, ramdisk, args)
File "/usr/lib/python2.7/site-packages/xen/xend/XendBootloader.py", line 215, in bootloader
raise VmError, msg
VmError: Boot loader didn't return any data!
Appreciate any suggestions.Hi,
I have a very similar issue. I've managed to create PVM guests under 3.0.1 and upgraded via YUM to 3.0.3. I now have 2 Hosts and created a guest Server that I downloaded from the Oracle Software Cloud. This boots fine and is accessible. I cannot create a standalone guest (I want to create a RHEL 5 Server) as this gives me the same error. The Server Pool has one Server Pool LUN and one Repo for the Guests.
I can create the guest and and add a small boot ISO from the ISO Repositiory, which I then intent to Kickstart the rest of the installation. When starting the Guest, the following is received:
Starting operation 'Virtual Machine Start' on object '0004fb0000060000951b61a25a250dc9 (csitestvl14)'
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: gbahel71.gb.xxxxxx.com failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 start_vm 0004fb00000300009edc3a187ae931f0 0004fb0000060000951b61a25a250dc9, Status: org.apache.xmlrpc.XmlRpcException: exceptions.RuntimeError:Command ['xm', 'create', '/OVS/Repositories/0004fb00000300009edc3a187ae931f0/VirtualMachines/0004fb0000060000951b61a25a250dc9/vm.cfg'] failed (1): stderr: Error: Boot loader didn't return any data!
, stdout: Using config file "/OVS/Repositories/0004fb00000300009edc3a187ae931f0/VirtualMachines/0004fb0000060000951b61a25a250dc9/vm.cfg".
Edited by: LeeUK on 20-Mar-2012 08:54 -
Boot loader didn't return any data!
I have set up an OVM 3.0.3 server at home with internal disks as its repository. I have another machine where the VM manager is configured. Since I have no other app server running at home, I use the VM Manager server as my app server. Still I am not able to create a virtual machine with network boot URL specified as this: http://192.168.1.20:7001/consolehelp/el48 - I have mounted the iso file of the Oracle Enterprise Linux 4.8 DVD (with -o loop) in this directory. See below the commands I have executed from the VM server (gramvs) to the VM manager(192.168.1.20):
[root@gramvs VirtualMachines]# date
Fri Mar 16 21:17:10 EDT 2012
[root@gramvs VirtualMachines]# ssh 192.168.1.20 df -k | egrep "R4|el48"
[email protected]'s password:
/root32/stage/OS/OEL48_64/Enterprise-R4-U8-x86_64-dvd.iso
2669604 2669604 0 100% /u01/app/oracle/Middleware/wlserver_10.3/server/lib/consoleapp/consolehelp/el48
[root@gramvs VirtualMachines]# ls -l README-en.html
ls: README-en.html: No such file or directory
[root@gramvs VirtualMachines]# wget http://192.168.1.20:7001/consolehelp/el48/README-en.html
--2012-03-16 21:17:47-- http://192.168.1.20:7001/consolehelp/el48/README-en.html
Connecting to 192.168.1.20:7001... connected.
HTTP request sent, awaiting response... 200 OK
Length: 6102 (6.0K) [text/html]
Saving to: `README-en.html'
100%[============================================================================>] 6,102 --.-K/s in 0s
2012-03-16 21:17:47 (330 MB/s) - `README-en.html' saved [6102/6102]
[root@gramvs VirtualMachines]# ls -l README-en.html
-rw-r--r-- 1 root root 6102 May 20 2009 README-en.html
[root@gramvs VirtualMachines]# ssh 192.168.1.20 ls -l /u01/app/oracle/Middleware/wlserver_10.3/server/lib/consoleapp/consolehelp/el48
[email protected]'s password:
total 115
-r-xr-xr-x. 3 root root 248 May 20 2009 autorun
-r--r--r--. 3 root root 5165 May 20 2009 blafdoc.css
dr-xr-xr-x. 4 root root 2048 May 21 2009 Enterprise
-r--r--r--. 13 root root 7037 May 20 2009 EULA
-r--r--r--. 3 root root 7037 May 20 2009 eula.en_US
-r--r--r--. 3 root root 3334 May 20 2009 eula.py
-r--r--r--. 13 root root 18390 May 20 2009 GPL
dr-xr-xr-x. 4 root root 2048 May 21 2009 images
dr-xr-xr-x. 2 root root 2048 May 21 2009 isolinux
-r--r--r--. 3 root root 3548 May 20 2009 README-en
-r--r--r--. 3 root root 6102 May 20 2009 README-en.html
-r--r--r--. 3 root root 9927 May 20 2009 RELEASE-NOTES-en
-r--r--r--. 3 root root 13565 May 20 2009 RELEASE-NOTES-en.html
-r--r--r--. 3 root root 9927 May 20 2009 RELEASE-NOTES-U8-en
-r--r--r--. 3 root root 13565 May 20 2009 RELEASE-NOTES-U8-en.html
-r--r--r--. 13 root root 1954 May 20 2009 RPM-GPG-KEY
-r--r--r--. 3 root root 1954 May 20 2009 RPM-GPG-KEY-oracle
dr-xr-xr-x. 2 root root 2048 May 21 2009 SRPMS
-r--r--r--. 3 root root 105 May 20 2009 supportinfo
-r--r--r--. 1 root root 4463 May 21 2009 TRANS.TBL
[root@gramvs VirtualMachines]# date
Fri Mar 16 21:19:02 EDT 2012
==================
From the above, I know that the network is fine (ssh works) and the URL is fine too (wget works). Yet when I try to boot the guest from VM Manager, it immediately aborts with "Boot loader didn't return any data!" Please see below:
Starting operation 'Virtual Machine Start' on object '0004fb000006000002b172ab7bc0fbe8 (oemel48)'
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: start_vm to server: gramvs.home.gram.com failed. OVMAPI_4004E Server Failed Command: start_vm 0004fb00000300008cfb55d16e006e8b 0004fb000006000002b172ab7bc0fbe8, Status: org.apache.xmlrpc.XmlRpcException: exceptions.RuntimeError:Command ['xm', 'create', '/OVS/Repositories/0004fb00000300008cfb55d16e006e8b/VirtualMachines/0004fb000006000002b172ab7bc0fbe8/vm.cfg'] failed (1): stderr: Error: Boot loader didn't return any data!
, stdout: Using config file "/OVS/Repositories/0004fb00000300008cfb55d16e006e8b/VirtualMachines/0004fb000006000002b172ab7bc0fbe8/vm.cfg".
The strange thing is when I installed the VM server a couple of months back, I managed to install a couple of OEL guests using exactly the same method (mounting the ISO file into a directory under the same place and using the URL to VM manager server).
Anyone could see what I am doing wrong here? Any help would greatly be appreciated. Thanks!
- Govardhanan.Hi,
I have a very similar issue. I've managed to create PVM guests under 3.0.1 and upgraded via YUM to 3.0.3. I now have 2 Hosts and created a guest Server that I downloaded from the Oracle Software Cloud. This boots fine and is accessible. I cannot create a standalone guest (I want to create a RHEL 5 Server) as this gives me the same error. The Server Pool has one Server Pool LUN and one Repo for the Guests.
I can create the guest and and add a small boot ISO from the ISO Repositiory, which I then intent to Kickstart the rest of the installation. When starting the Guest, the following is received:
Starting operation 'Virtual Machine Start' on object '0004fb0000060000951b61a25a250dc9 (csitestvl14)'
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: gbahel71.gb.xxxxxx.com failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 start_vm 0004fb00000300009edc3a187ae931f0 0004fb0000060000951b61a25a250dc9, Status: org.apache.xmlrpc.XmlRpcException: exceptions.RuntimeError:Command ['xm', 'create', '/OVS/Repositories/0004fb00000300009edc3a187ae931f0/VirtualMachines/0004fb0000060000951b61a25a250dc9/vm.cfg'] failed (1): stderr: Error: Boot loader didn't return any data!
, stdout: Using config file "/OVS/Repositories/0004fb00000300009edc3a187ae931f0/VirtualMachines/0004fb0000060000951b61a25a250dc9/vm.cfg".
Edited by: LeeUK on 20-Mar-2012 08:54 -
Latitude E5440 - Truecrypt Boot Loader Problems
I've been using Truecrypt for many years on Latitude D and E Series laptops and never had a problem until we upgraded to E5440's. Now I continually get Truecrypt boot loader errors.
I've tried versions 7.1 and 7.1a and FDE as well as just encrypting the System Partition. What happens is that when the computer is started up, I get a black screen with a white blinking cursor.
The temporary fix is easy. I boot off the Truecrypt Rescue disk and Repair the Truecrypt Boot Loader. This works for several days and then it happens again.
I am lost as to a solution, but I believe it might involve one of the following:
1. Hybrid Hard Drives. These E5440's have a Samsung 500GB hybrid drive in them. I am wondering if some file or component of Truecrypt is being put on the Flash drive component of the HD and it becomes unavailable at boot up.
2. Closing the lid of the laptop instead of shutting it down for transport.
If you've had similar problems or have any insight into this issue, I would love to get your feedback.
Thanks, Greg
Also, these laptops run W7 Pro.I've been using Truecrypt for many years on Latitude D and E Series laptops and never had a problem until we upgraded to E5440's. Now I continually get Truecrypt boot loader errors.
I've tried versions 7.1 and 7.1a and FDE as well as just encrypting the System Partition. What happens is that when the computer is started up, I get a black screen with a white blinking cursor.
The temporary fix is easy. I boot off the Truecrypt Rescue disk and Repair the Truecrypt Boot Loader. This works for several days and then it happens again.
I am lost as to a solution, but I believe it might involve one of the following:
1. Hybrid Hard Drives. These E5440's have a Samsung 500GB hybrid drive in them. I am wondering if some file or component of Truecrypt is being put on the Flash drive component of the HD and it becomes unavailable at boot up.
2. Closing the lid of the laptop instead of shutting it down for transport.
If you've had similar problems or have any insight into this issue, I would love to get your feedback.
Thanks, Greg
Also, these laptops run W7 Pro. -
3750x doesn't boot after upgrade to version15
Due to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode.
When i look at the version i See that bootloader is still the old version 12.2.58.
It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
Is there anything i can do to Upgrade the bootloader seperatly?
It's a 3750X48PF-S
Many thanks
AndyThis is a stack of 2 switches, both have the same problem and they are still running old image (as V15 doesn't work)
cs156005#sh license
Index 1 Feature: ipservices
Period left: 8 weeks 4 days
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
License Priority: None
License Count: Non-Counted
Index 2 Feature: ipbase
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Priority: Medium
License Count: Non-Counted
Index 3 Feature: lanbase
Period left: 0 minute 0 second
cs156005#sh inventory
NAME: "1", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V02 , SN: FDO1527P0J8
NAME: "Switch 1 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT15060D4H
NAME: "Switch 1 - FRULink Slot 1 - FRULink Module", DESCR: "FRULink 10G ST Module"
PID: C3KX-NM-10G , VID: V01 , SN: FDO14350PDY
NAME: "GigabitEthernet1/1/3", DESCR: "1000BaseLX SFP"
PID: Unspecified , VID: , SN: PR04004346
NAME: "2", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V04 , SN: FDO1649P24J
NAME: "Switch 2 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT16371ZBN
cs156005#sh version
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 01:56 by prod_rel_team
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
cs156005 uptime is 1 hour, 14 minutes
System returned to ROM by power-on
System restarted at 10:11:49 cet Tue Jul 9 2013
System image file is "flash:/c3750e-universalk9-mz.122-58.SE1/c3750e-universalk9-mz.122-58.SE1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1527P0J8
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
104 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : A4:93:4C:95:EC:00
Motherboard assembly number : 73-12553-05
Motherboard serial number : FDO162001GA
Model revision number : A0
Motherboard revision number : D0
Model number : WS-C3750X-48PF-S
Daughterboard assembly number : 800-32727-01
Daughterboard serial number : FDO16200KPU
System serial number : FDO1527P0J8
Top Assembly Part Number : 800-31324-02
Top Assembly Revision Number : E0
Version ID : V02
CLEI Code Number : COMJZ00ARB
Hardware Board Revision Number : 0x03
Switch Ports Model SW Version SW Image
* 1 54 WS-C3750X-48P 12.2(58)SE1 C3750E-UNIVERSALK9-M
2 54 WS-C3750X-48P 12.2(58)SE1 C3750E-UNIVERSALK9-M
Switch 02
Switch Uptime : 1 hour, 14 minutes
Base ethernet MAC Address : 44:03:A7:58:AC:80
Motherboard assembly number : 73-12553-08
Motherboard serial number : FDO164831LB
Model revision number : K0
Motherboard revision number : A0
Model number : WS-C3750X-48PF-S
Daughterboard assembly number : 800-32727-03
Daughterboard serial number : FDO16491JNK
System serial number : FDO1649P24J
Top assembly part number : 800-31324-07
Top assembly revision number : B0
Version ID : V04
CLEI Code Number : COMJZ00ARD
License Level : ipbase
License Type : Permanent
Next reboot licensing Level : ipbase
Configuration register is 0xF
cs156005# -
[SOLVED] efibootmgr not generating boot loader (rEFInd, etc.) entry.
Hello,
The following command runs without problem or any output. It wouldn't create any entry. Also my refind.conf is not being followed. rEFInd is able to detect kernels and boot fine from /boot
efibootmgr -c -g -d /dev/sda -p 1 -w -L "rEFInd" -l '\EFI\refind\refind_x64.efi'
Information
efibootmgr 0.6.0-1
refind-efi 0.6.8-1
Linux 3.8.4-1-ARCH
sudo efibootmgr
BootCurrent: 000A
Timeout: 0 seconds
BootOrder: 0006,0007,0008,0009,000A,000B,000C,000D,000E,000F,0010,0011,0012,0013
Boot0000 Setup
Boot0001 Boot Menu
Boot0002 Diagnostic Splash Screen
Boot0003 Startup Interrupt Menu
Boot0004 ME Configuration Menu
Boot0005 Rescue and Recovery
Boot0006* USB CD
Boot0007* USB FDD
Boot0008* ATAPI CD0
Boot0009* ATA HDD2
Boot000A* ATA HDD0
Boot000B* ATA HDD1
Boot000C* USB HDD
Boot000D* PCI LAN
Boot000E* ATAPI CD1
Boot000F* ATAPI CD2
Boot0010 Other CD
Boot0011* ATA HDD3
Boot0012* ATA HDD4
Boot0013 Other HDD
Boot0014* IDER BOOT CDROM
Boot0015* IDER BOOT Floppy
Boot0016* ATA HDD
Boot0017* ATAPI CD:
Boot0018* PCI LAN
ls -R /boot
/boot:
EFI initramfs-linux-fallback.img initramfs-linux.img refind_linux.conf vmlinuz-linux
/boot/EFI:
boot refind tools
/boot/EFI/boot:
bootx64.efi icons refind.conf
/boot/EFI/boot/icons:
*** Icons
/boot/EFI/refind:
icons refind.conf refind_x64.efi
/boot/EFI/refind/icons:
*** icons
/boot/EFI/tools:
drivers shells
/boot/EFI/tools/drivers:
ext2_x64.efi ext4_x64.efi hfs_x64.efi iso9660_x64.efi reiserfs_x64.efi
/boot/EFI/tools/shells:
Shell.efi Shell_Full.efi
cat /boot/refind_linux.conf
"Boot to X" "root=PARTUUID=5416f920-35fc-42a8-8a34-564c8c332bfe ro rootfstype=ext4 add_efi_memmap systemd.unit=graphical.target"
"Boot to Console" "root=PARTUUID=5416f920-35fc-42a8-8a34-564c8c332bfe ro rootfstype=ext4 add_efi_memmap systemd.unit=multi-user.target"
# refind.conf
# Configuration file for the rEFInd boot menu
# Timeout in seconds for the main menu screen. Setting the timeout to 0
# disables automatic booting (i.e., no timeout).
timeout 5
# Hide user interface elements for personal preference or to increase
# security:
# banner - the rEFInd title banner (built-in or loaded via "banner")
# label - boot option text label in the menu
# singleuser - remove the submenu options to boot Mac OS X in single-user
# or verbose modes; affects ONLY MacOS X
# safemode - remove the submenu option to boot Mac OS X in "safe mode"
# hwtest - the submenu option to run Apple's hardware test
# arrows - scroll arrows on the OS selection tag line
# hints - brief command summary in the menu
# editor - the options editor (+, F2, or Insert on boot options menu)
# all - all of the above
# Default is none of these (all elements active)
#hideui singleuser
#hideui all
# Set the name of a subdirectory in which icons are stored. Icons must
# have the same names they have in the standard directory. The directory
# name is specified relative to the main rEFInd binary's directory. If
# an icon can't be found in the specified directory, an attempt is made
# to load it from the default directory; thus, you can replace just some
# icons in your own directory and rely on the default for others.
# Default is "icons".
#icons_dir myicons
# Use a custom title banner instead of the rEFInd icon and name. The file
# path is relative to the directory where refind.efi is located. The color
# in the top left corner of the image is used as the background color
# for the menu screens. Currently uncompressed BMP images with color
# depths of 24, 8, 4 or 1 bits are supported, as well as PNG images.
#banner hostname.bmp
#banner mybanner.png
# Custom images for the selection background. There is a big one (144 x 144)
# for the OS icons, and a small one (64 x 64) for the function icons in the
# second row. If only a small image is given, that one is also used for
# the big icons by stretching it in the middle. If only a big one is given,
# the built-in default will be used for the small icons.
# Like the banner option above, these options take a filename of an
# uncompressed BMP image file with a color depth of 24, 8, 4, or 1 bits,
# or a PNG image. The PNG format is required if you need transparency
# support (to let you "see through" to a full-screen banner).
#selection_big selection-big.bmp
#selection_small selection-small.bmp
# Set the font to be used for all textual displays in graphics mode.
# The font must be a PNG file with alpha channel transparency. It must
# contain ASCII characters 32-126 (space through tilde), inclusive, plus
# a glyph to be displayed in place of characters outside of this range,
# for a total of 96 glyphs. Only monospaced fonts are supported. Fonts
# may be of any size, although large fonts can produce display
# irregularities.
# The default is rEFInd's built-in font, Luxi Mono Regular 12 point.
#font myfont.png
# Use text mode only. When enabled, this option forces rEFInd into text mode.
# Passing this option a "0" value causes graphics mode to be used. Pasing
# it no value or any non-0 value causes text mode to be used.
# Default is to use graphics mode.
#textonly
textonly
# Set the EFI text mode to be used for textual displays. This option
# takes a single digit that refers to a mode number. Mode 0 is normally
# 80x25, 1 is sometimes 80x50, and higher numbers are system-specific
# modes. Mode 1024 is a special code that tells rEFInd to not set the
# text mode; it uses whatever was in use when the program was launched.
# If you specify an invalid mode, rEFInd pauses during boot to inform
# you of valid modes.
# CAUTION: On VirtualBox, and perhaps on some real computers, specifying
# a text mode and uncommenting the "textonly" option while NOT specifying
# a resolution can result in an unusable display in the booted OS.
# Default is 1024 (no change)
#textmode 2
textmode 1024
# Set the screen's video resolution. Pass this option either:
# * two values, corresponding to the X and Y resolutions
# * one value, corresponding to a GOP (UEFI) video mode
# Note that not all resolutions are supported. On UEFI systems, passing
# an incorrect value results in a message being shown on the screen to
# that effect, along with a list of supported modes. On EFI 1.x systems
# (e.g., Macintoshes), setting an incorrect mode silently fails. On both
# types of systems, setting an incorrect resolution results in the default
# resolution being used. A resolution of 1024x768 usually works, but higher
# values often don't.
# Default is "0 0" (use the system default resolution, usually 800x600).
#resolution 1024 768
#resolution 3
resolution 1024 768
# Launch specified OSes in graphics mode. By default, rEFInd switches
# to text mode and displays basic pre-launch information when launching
# all OSes except OS X. Using graphics mode can produce a more seamless
# transition, but displays no information, which can make matters
# difficult if you must debug a problem. Also, on at least one known
# computer, using graphics mode prevents a crash when using the Linux
# kernel's EFI stub loader. You can specify an empty list to boot all
# OSes in text mode.
# Valid options:
# osx - Mac OS X
# linux - A Linux kernel with EFI stub loader
# elilo - The ELILO boot loader
# grub - The GRUB (Legacy or 2) boot loader
# windows - Microsoft Windows
# Default value: osx
#use_graphics_for osx,linux
# Which non-bootloader tools to show on the tools line, and in what
# order to display them:
# shell - the EFI shell (requires external program; see rEFInd
# documentation for details)
# gptsync - the (dangerous) gptsync.efi utility (requires external
# program; see rEFInd documentation for details)
# apple_recovery - boots the Apple Recovery HD partition, if present
# mok_tool - makes available the Machine Owner Key (MOK) maintenance
# tool, MokManager.efi, used on Secure Boot systems
# about - an "about this program" option
# exit - a tag to exit from rEFInd
# shutdown - shuts down the computer (a bug causes this to reboot
# EFI systems)
# reboot - a tag to reboot the computer
# Default is shell,apple_recovery,mok_tool,about,shutdown,reboot
#showtools shell, mok_tool, about, reboot, exit
showtools shell, mok_tool, about, reboot, exit
# Directories in which to search for EFI drivers. These drivers can
# provide filesystem support, give access to hard disks on plug-in
# controllers, etc. In most cases none are needed, but if you add
# EFI drivers and you want rEFInd to automatically load them, you
# should specify one or more paths here. rEFInd always scans the
# "drivers" and "drivers_{arch}" subdirectories of its own installation
# directory (where "{arch}" is your architecture code); this option
# specifies ADDITIONAL directories to scan.
# Default is to scan no additional directories for EFI drivers
#scan_driver_dirs EFI/tools/drivers,drivers
scan_driver_dirs /boot/EFI/tools/drivers,drivers
# Which types of boot loaders to search, and in what order to display them:
# internal - internal EFI disk-based boot loaders
# external - external EFI disk-based boot loaders
# optical - EFI optical discs (CD, DVD, etc.)
# hdbios - BIOS disk-based boot loaders
# biosexternal - BIOS external boot loaders (USB, eSATA, etc.)
# cd - BIOS optical-disc boot loaders
# manual - use stanzas later in this configuration file
# Note that the legacy BIOS options require firmware support, which is
# not present on all computers.
# On UEFI PCs, default is internal,external,optical,manual
# On Macs, default is internal,hdbios,external,biosexternal,optical,cd,manual
#scanfor internal,external,optical,manual
scanfor internal,external,optical,manual
# Delay for the specified number of seconds before scanning disks.
# This can help some users who find that some of their disks
# (usually external or optical discs) aren't detected initially,
# but are detected after pressing Esc.
# The default is 0.
#scan_delay 5
# When scanning volumes for EFI boot loaders, rEFInd always looks for
# Mac OS X's and Microsoft Windows' boot loaders in their normal locations,
# and scans the root directory and every subdirectory of the /EFI directory
# for additional boot loaders, but it doesn't recurse into these directories.
# The also_scan_dirs token adds more directories to the scan list.
# Directories are specified relative to the volume's root directory. This
# option applies to ALL the volumes that rEFInd scans UNLESS you include
# a volume name and colon before the directory name, as in "myvol:/somedir"
# to scan the somedir directory only on the filesystem named myvol. If a
# specified directory doesn't exist, it's ignored (no error condition
# results). The default is to scan the "boot" directory in addition to
# various hard-coded directories.
#also_scan_dirs boot,ESP2:EFI/linux/kernels
# Partitions to omit from scans. You must specify a volume by its
# label, which you can obtain in an EFI shell by typing "vol", from
# Linux by typing "blkid /dev/{devicename}", or by examining the
# disk's label in various OSes' file browsers.
# The default is "Recovery HD".
#dont_scan_volumes "Recovery HD"
# Directories that should NOT be scanned for boot loaders. By default,
# rEFInd doesn't scan its own directory or the EFI/tools directory.
# You can "blacklist" additional directories with this option, which
# takes a list of directory names as options. You might do this to
# keep EFI/boot/bootx64.efi out of the menu if that's a duplicate of
# another boot loader or to exclude a directory that holds drivers
# or non-bootloader utilities provided by a hardware manufacturer. If
# a directory is listed both here and in also_scan_dirs, dont_scan_dirs
# takes precedence. Note that this blacklist applies to ALL the
# filesystems that rEFInd scans, not just the ESP, unless you precede
# the directory name by a filesystem name, as in "myvol:EFI/somedir"
# to exclude EFI/somedir from the scan on the myvol volume but not on
# other volumes.
#dont_scan_dirs ESP:/EFI/boot,EFI/Dell
# Files that should NOT be included as EFI boot loaders (on the
# first line of the display). If you're using a boot loader that
# relies on support programs or drivers that are installed alongside
# the main binary or if you want to "blacklist" certain loaders by
# name rather than location, use this option. Note that this will
# NOT prevent certain binaries from showing up in the second-row
# set of tools. Most notably, MokManager.efi is in this blacklist,
# but will show up as a tool if present in certain directories. You
# can control the tools row with the showtools token.
# The default is shim.efi,TextMode.efi,ebounce.efi,GraphicsConsole.efi,MokManager.efi,HashTool.efi,HashTool-signed.efi
#dont_scan_files shim.efi,MokManager.efi
# Scan for Linux kernels that lack a ".efi" filename extension. This is
# useful for better integration with Linux distributions that provide
# kernels with EFI stub loaders but that don't give those kernels filenames
# that end in ".efi", particularly if the kernels are stored on a
# filesystem that the EFI can read. When uncommented, this option causes
# all files in scanned directories with names that begin with "vmlinuz"
# or "bzImage" to be included as loaders, even if they lack ".efi"
# extensions. The drawback to this option is that it can pick up kernels
# that lack EFI stub loader support and other files. Passing this option
# a "0" value causes kernels without ".efi" extensions to NOT be scanned;
# passing it alone or with any other value causes all kernels to be scanned.
# Default is to NOT scan for kernels without ".efi" extensions.
scan_all_linux_kernels
# Set the maximum number of tags that can be displayed on the screen at
# any time. If more loaders are discovered than this value, rEFInd shows
# a subset in a scrolling list. If this value is set too high for the
# screen to handle, it's reduced to the value that the screen can manage.
# If this value is set to 0 (the default), it's adjusted to the number
# that the screen can handle.
#max_tags 0
# Set the default menu selection. The available arguments match the
# keyboard accelerators available within rEFInd. You may select the
# default loader using:
# - A digit between 1 and 9, in which case the Nth loader in the menu
# will be the default.
# - Any substring that corresponds to a portion of the loader's title
# (usually the OS's name or boot loader's path).
#default_selection 1
default_selection "vmlinuz-linux"
# Include a secondary configuration file within this one. This secondary
# file is loaded as if its options appeared at the point of the "include"
# token itself, so if you want to override a setting in the main file,
# the secondary file must be referenced AFTER the setting you want to
# override. Note that the secondary file may NOT load a tertiary file.
#include manual.conf
# Sample manual configuration stanzas. Each begins with the "menuentry"
# keyword followed by a name that's to appear in the menu (use quotes
# if you want the name to contain a space) and an open curly brace
# ("{"). Each entry ends with a close curly brace ("}"). Common
# keywords within each stanza include:
# volume - identifies the filesystem from which subsequent files
# are loaded. You can specify the volume by label or by
# a number followed by a colon (as in "0:" for the first
# filesystem or "1:" for the second).
# loader - identifies the boot loader file
# initrd - Specifies an initial RAM disk file
# icon - specifies a custom boot loader icon
# ostype - OS type code to determine boot options available by
# pressing Insert. Valid values are "MacOS", "Linux",
# "Windows", and "XOM". Case-sensitive.
# graphics - set to "on" to enable graphics-mode boot (useful
# mainly for MacOS) or "off" for text-mode boot.
# Default is auto-detected from loader filename.
# options - sets options to be passed to the boot loader; use
# quotes if more than one option should be passed or
# if any options use characters that might be changed
# by rEFInd parsing procedures (=, /, #, or tab).
# disabled - use alone or set to "yes" to disable this entry.
# Note that you can use either DOS/Windows/EFI-style backslashes (\)
# or Unix-style forward slashes (/) as directory separators. Either
# way, all file references are on the ESP from which rEFInd was
# launched.
# Use of quotes around parameters causes them to be interpreted as
# one keyword, and for parsing of special characters (spaces, =, /,
# and #) to be disabled. This is useful mainly with the "options"
# keyword. Use of quotes around parameters that specify filenames is
# permissible, but you must then use backslashes instead of slashes,
# except when you must pass a forward slash to the loader, as when
# passing a root= option to a Linux kernel.
# Below are several sample boot stanzas. All are disabled by default.
# Find one similar to what you need, copy it, remove the "disabled" line,
# and adjust the entries to suit your needs.
# A sample entry for a Linux 3.3 kernel with its new EFI boot stub
# support on a filesystem called "KERNELS". This entry includes
# Linux-specific boot options and specification of an initial RAM disk.
# Note uses of Linux-style forward slashes, even in the initrd
# specification. Also note that a leading slash is optional in file
# specifications.
menuentry Linux {
icon EFI/refind/icons/os_linux.icns
volume KERNELS
loader bzImage-3.3.0-rc7
initrd initrd-3.3.0.img
options "ro root=UUID=5f96cafa-e0a7-4057-b18f-fa709db5b837"
disabled
# A sample entry for loading Ubuntu using its standard name for
# its GRUB 2 boot loader. Note uses of Linux-style forward slashes
menuentry Ubuntu {
loader /EFI/ubuntu/grubx64.efi
icon /EFI/refined/icons/os_linux.icns
disabled
# A minimal ELILO entry, which probably offers nothing that
# auto-detection can't accomplish.
menuentry "ELILO" {
loader \EFI\elilo\elilo.efi
disabled
# Like the ELILO entry, this one offers nothing that auto-detection
# can't do; but you might use it if you want to disable auto-detection
# but still boot Windows....
menuentry "Windows 7" {
loader \EFI\Microsoft\Boot\bootmgfw.efi
disabled
# EFI shells are programs just like boot loaders, and can be
# launched in the same way. You can pass a shell the name of a
# script that it's to run on the "options" line. The script
# could initialize hardware and then launch an OS, or it could
# do something entirely different.
menuentry "Windows via shell script" {
icon \EFI\refind\icons\os_win.icns
loader \EFI\tools\shell.efi
options "fs0:\EFI\tools\launch_windows.nsh"
disabled
# Mac OS is normally detected and run automatically; however,
# if you want to do something unusual, a manual boot stanza may
# be the way to do it. This one does nothing very unusual, but
# it may serve as a starting point. Note that you'll almost
# certainly need to change the "volume" line for this example
# to work.
menuentry "My Mac OS X" {
icon \EFI\refind\icons\os_mac.icns
volume "OS X boot"
loader \System\Library\CoreServices\boot.efi
disabled
cat /etc/fstab
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda2
UUID=7b92a840-4747-43b7-b2cf-02cbf92afce7 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda4
UUID=72f64fd4-a3f1-424c-8fe3-cdf7751a84e0 /home ext4 rw,relatime,data=ordered 0 2
# /dev/sda1
# UUID=5447-7409 /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
UUID=5447-7409 /boot vfat noatime 0 2
# /dev/sda3
UUID=1e11bea5-41db-4969-a8fa-a461734b71ac none swap defaults 0 0
This is a clean install using April 01 ISO with minimal or no modifications. I have tried to follow wiki as precisely as possible. I am not sure what I am missing. Thanks.
EDIT1: Updated and cleaned the post to better reflect current structure and added /etc/fstab.
EDIT2: @swordfish Removed /boot/EFI/arch.
Last edited by donniezazen (2013-04-04 06:37:07)I used March ISO instead of April ISO and it worked flawlessly. There is some problem with April ISO where efibootmgr and UEFI Shell1/2 fail with ASSERT_EFI_ERROR (status = device error).
I have removed both /boot/EFI/boot and /boot/EFI/arch. I now have two entries one on vmlinuz-linux on 1024 Fat 32 partition which works and second one boot/vmlinuz-linux on 20G / partition which fails and takes me to rootfs. Also refind isn't showing UEFI shells that I have in /boot/EFI/tools/Shells.
ls -R /boot
/boot:
EFI initramfs-linux-fallback.img initramfs-linux.img refind_linux.conf vmlinuz-linux
/boot/EFI:
drivers refind tools
/boot/EFI/drivers:
ext2_x64.efi ext4_x64.efi hfs_x64.efi iso9660_x64.efi reiserfs_x64.efi
/boot/EFI/refind:
icons refind.conf refind_x64.efi
/boot/EFI/refind/icons:
### Icons
/boot/EFI/tools:
Shell.efi
# refind.conf
# Configuration file for the rEFInd boot menu
# Timeout in seconds for the main menu screen. Setting the timeout to 0
# disables automatic booting (i.e., no timeout).
timeout 5
# Hide user interface elements for personal preference or to increase
# security:
# banner - the rEFInd title banner (built-in or loaded via "banner")
# label - boot option text label in the menu
# singleuser - remove the submenu options to boot Mac OS X in single-user
# or verbose modes; affects ONLY MacOS X
# safemode - remove the submenu option to boot Mac OS X in "safe mode"
# hwtest - the submenu option to run Apple's hardware test
# arrows - scroll arrows on the OS selection tag line
# hints - brief command summary in the menu
# editor - the options editor (+, F2, or Insert on boot options menu)
# all - all of the above
# Default is none of these (all elements active)
#hideui singleuser
#hideui all
# Set the name of a subdirectory in which icons are stored. Icons must
# have the same names they have in the standard directory. The directory
# name is specified relative to the main rEFInd binary's directory. If
# an icon can't be found in the specified directory, an attempt is made
# to load it from the default directory; thus, you can replace just some
# icons in your own directory and rely on the default for others.
# Default is "icons".
#icons_dir myicons
# Use a custom title banner instead of the rEFInd icon and name. The file
# path is relative to the directory where refind.efi is located. The color
# in the top left corner of the image is used as the background color
# for the menu screens. Currently uncompressed BMP images with color
# depths of 24, 8, 4 or 1 bits are supported, as well as PNG images.
#banner hostname.bmp
#banner mybanner.png
# Custom images for the selection background. There is a big one (144 x 144)
# for the OS icons, and a small one (64 x 64) for the function icons in the
# second row. If only a small image is given, that one is also used for
# the big icons by stretching it in the middle. If only a big one is given,
# the built-in default will be used for the small icons.
# Like the banner option above, these options take a filename of an
# uncompressed BMP image file with a color depth of 24, 8, 4, or 1 bits,
# or a PNG image. The PNG format is required if you need transparency
# support (to let you "see through" to a full-screen banner).
#selection_big selection-big.bmp
#selection_small selection-small.bmp
# Set the font to be used for all textual displays in graphics mode.
# The font must be a PNG file with alpha channel transparency. It must
# contain ASCII characters 32-126 (space through tilde), inclusive, plus
# a glyph to be displayed in place of characters outside of this range,
# for a total of 96 glyphs. Only monospaced fonts are supported. Fonts
# may be of any size, although large fonts can produce display
# irregularities.
# The default is rEFInd's built-in font, Luxi Mono Regular 12 point.
#font myfont.png
# Use text mode only. When enabled, this option forces rEFInd into text mode.
# Passing this option a "0" value causes graphics mode to be used. Pasing
# it no value or any non-0 value causes text mode to be used.
# Default is to use graphics mode.
#textonly
textonly
# Set the EFI text mode to be used for textual displays. This option
# takes a single digit that refers to a mode number. Mode 0 is normally
# 80x25, 1 is sometimes 80x50, and higher numbers are system-specific
# modes. Mode 1024 is a special code that tells rEFInd to not set the
# text mode; it uses whatever was in use when the program was launched.
# If you specify an invalid mode, rEFInd pauses during boot to inform
# you of valid modes.
# CAUTION: On VirtualBox, and perhaps on some real computers, specifying
# a text mode and uncommenting the "textonly" option while NOT specifying
# a resolution can result in an unusable display in the booted OS.
# Default is 1024 (no change)
#textmode 2
textmode 1024
# Set the screen's video resolution. Pass this option either:
# * two values, corresponding to the X and Y resolutions
# * one value, corresponding to a GOP (UEFI) video mode
# Note that not all resolutions are supported. On UEFI systems, passing
# an incorrect value results in a message being shown on the screen to
# that effect, along with a list of supported modes. On EFI 1.x systems
# (e.g., Macintoshes), setting an incorrect mode silently fails. On both
# types of systems, setting an incorrect resolution results in the default
# resolution being used. A resolution of 1024x768 usually works, but higher
# values often don't.
# Default is "0 0" (use the system default resolution, usually 800x600).
#resolution 1024 768
#resolution 3
resolution 1024 768
# Launch specified OSes in graphics mode. By default, rEFInd switches
# to text mode and displays basic pre-launch information when launching
# all OSes except OS X. Using graphics mode can produce a more seamless
# transition, but displays no information, which can make matters
# difficult if you must debug a problem. Also, on at least one known
# computer, using graphics mode prevents a crash when using the Linux
# kernel's EFI stub loader. You can specify an empty list to boot all
# OSes in text mode.
# Valid options:
# osx - Mac OS X
# linux - A Linux kernel with EFI stub loader
# elilo - The ELILO boot loader
# grub - The GRUB (Legacy or 2) boot loader
# windows - Microsoft Windows
# Default value: osx
#use_graphics_for osx,linux
# Which non-bootloader tools to show on the tools line, and in what
# order to display them:
# shell - the EFI shell (requires external program; see rEFInd
# documentation for details)
# gptsync - the (dangerous) gptsync.efi utility (requires external
# program; see rEFInd documentation for details)
# apple_recovery - boots the Apple Recovery HD partition, if present
# mok_tool - makes available the Machine Owner Key (MOK) maintenance
# tool, MokManager.efi, used on Secure Boot systems
# about - an "about this program" option
# exit - a tag to exit from rEFInd
# shutdown - shuts down the computer (a bug causes this to reboot
# EFI systems)
# reboot - a tag to reboot the computer
# Default is shell,apple_recovery,mok_tool,about,shutdown,reboot
#showtools shell, mok_tool, about, reboot, exit
showtools shell, about, reboot, exit
# Directories in which to search for EFI drivers. These drivers can
# provide filesystem support, give access to hard disks on plug-in
# controllers, etc. In most cases none are needed, but if you add
# EFI drivers and you want rEFInd to automatically load them, you
# should specify one or more paths here. rEFInd always scans the
# "drivers" and "drivers_{arch}" subdirectories of its own installation
# directory (where "{arch}" is your architecture code); this option
# specifies ADDITIONAL directories to scan.
# Default is to scan no additional directories for EFI drivers
#scan_driver_dirs EFI/tools/drivers,drivers
scan_driver_dirs EFI/tools/drivers,drivers
# Which types of boot loaders to search, and in what order to display them:
# internal - internal EFI disk-based boot loaders
# external - external EFI disk-based boot loaders
# optical - EFI optical discs (CD, DVD, etc.)
# hdbios - BIOS disk-based boot loaders
# biosexternal - BIOS external boot loaders (USB, eSATA, etc.)
# cd - BIOS optical-disc boot loaders
# manual - use stanzas later in this configuration file
# Note that the legacy BIOS options require firmware support, which is
# not present on all computers.
# On UEFI PCs, default is internal,external,optical,manual
# On Macs, default is internal,hdbios,external,biosexternal,optical,cd,manual
#scanfor internal,external,optical,manual
scanfor internal,external,optical,manual
# Delay for the specified number of seconds before scanning disks.
# This can help some users who find that some of their disks
# (usually external or optical discs) aren't detected initially,
# but are detected after pressing Esc.
# The default is 0.
#scan_delay 5
# When scanning volumes for EFI boot loaders, rEFInd always looks for
# Mac OS X's and Microsoft Windows' boot loaders in their normal locations,
# and scans the root directory and every subdirectory of the /EFI directory
# for additional boot loaders, but it doesn't recurse into these directories.
# The also_scan_dirs token adds more directories to the scan list.
# Directories are specified relative to the volume's root directory. This
# option applies to ALL the volumes that rEFInd scans UNLESS you include
# a volume name and colon before the directory name, as in "myvol:/somedir"
# to scan the somedir directory only on the filesystem named myvol. If a
# specified directory doesn't exist, it's ignored (no error condition
# results). The default is to scan the "boot" directory in addition to
# various hard-coded directories.
#also_scan_dirs boot,ESP2:EFI/linux/kernels
# Partitions to omit from scans. You must specify a volume by its
# label, which you can obtain in an EFI shell by typing "vol", from
# Linux by typing "blkid /dev/{devicename}", or by examining the
# disk's label in various OSes' file browsers.
# The default is "Recovery HD".
#dont_scan_volumes "Recovery HD"
# Directories that should NOT be scanned for boot loaders. By default,
# rEFInd doesn't scan its own directory or the EFI/tools directory.
# You can "blacklist" additional directories with this option, which
# takes a list of directory names as options. You might do this to
# keep EFI/boot/bootx64.efi out of the menu if that's a duplicate of
# another boot loader or to exclude a directory that holds drivers
# or non-bootloader utilities provided by a hardware manufacturer. If
# a directory is listed both here and in also_scan_dirs, dont_scan_dirs
# takes precedence. Note that this blacklist applies to ALL the
# filesystems that rEFInd scans, not just the ESP, unless you precede
# the directory name by a filesystem name, as in "myvol:EFI/somedir"
# to exclude EFI/somedir from the scan on the myvol volume but not on
# other volumes.
#dont_scan_dirs ESP:/EFI/boot,EFI/Dell
# Files that should NOT be included as EFI boot loaders (on the
# first line of the display). If you're using a boot loader that
# relies on support programs or drivers that are installed alongside
# the main binary or if you want to "blacklist" certain loaders by
# name rather than location, use this option. Note that this will
# NOT prevent certain binaries from showing up in the second-row
# set of tools. Most notably, MokManager.efi is in this blacklist,
# but will show up as a tool if present in certain directories. You
# can control the tools row with the showtools token.
# The default is shim.efi,TextMode.efi,ebounce.efi,GraphicsConsole.efi,MokManager.efi,HashTool.efi,HashTool-signed.efi
#dont_scan_files shim.efi,MokManager.efi
# Scan for Linux kernels that lack a ".efi" filename extension. This is
# useful for better integration with Linux distributions that provide
# kernels with EFI stub loaders but that don't give those kernels filenames
# that end in ".efi", particularly if the kernels are stored on a
# filesystem that the EFI can read. When uncommented, this option causes
# all files in scanned directories with names that begin with "vmlinuz"
# or "bzImage" to be included as loaders, even if they lack ".efi"
# extensions. The drawback to this option is that it can pick up kernels
# that lack EFI stub loader support and other files. Passing this option
# a "0" value causes kernels without ".efi" extensions to NOT be scanned;
# passing it alone or with any other value causes all kernels to be scanned.
# Default is to NOT scan for kernels without ".efi" extensions.
scan_all_linux_kernels
# Set the maximum number of tags that can be displayed on the screen at
# any time. If more loaders are discovered than this value, rEFInd shows
# a subset in a scrolling list. If this value is set too high for the
# screen to handle, it's reduced to the value that the screen can manage.
# If this value is set to 0 (the default), it's adjusted to the number
# that the screen can handle.
#max_tags 0
# Set the default menu selection. The available arguments match the
# keyboard accelerators available within rEFInd. You may select the
# default loader using:
# - A digit between 1 and 9, in which case the Nth loader in the menu
# will be the default.
# - Any substring that corresponds to a portion of the loader's title
# (usually the OS's name or boot loader's path).
#default_selection 1
# Include a secondary configuration file within this one. This secondary
# file is loaded as if its options appeared at the point of the "include"
# token itself, so if you want to override a setting in the main file,
# the secondary file must be referenced AFTER the setting you want to
# override. Note that the secondary file may NOT load a tertiary file.
#include manual.conf
# Sample manual configuration stanzas. Each begins with the "menuentry"
# keyword followed by a name that's to appear in the menu (use quotes
# if you want the name to contain a space) and an open curly brace
# ("{"). Each entry ends with a close curly brace ("}"). Common
# keywords within each stanza include:
# volume - identifies the filesystem from which subsequent files
# are loaded. You can specify the volume by label or by
# a number followed by a colon (as in "0:" for the first
# filesystem or "1:" for the second).
# loader - identifies the boot loader file
# initrd - Specifies an initial RAM disk file
# icon - specifies a custom boot loader icon
# ostype - OS type code to determine boot options available by
# pressing Insert. Valid values are "MacOS", "Linux",
# "Windows", and "XOM". Case-sensitive.
# graphics - set to "on" to enable graphics-mode boot (useful
# mainly for MacOS) or "off" for text-mode boot.
# Default is auto-detected from loader filename.
# options - sets options to be passed to the boot loader; use
# quotes if more than one option should be passed or
# if any options use characters that might be changed
# by rEFInd parsing procedures (=, /, #, or tab).
# disabled - use alone or set to "yes" to disable this entry.
# Note that you can use either DOS/Windows/EFI-style backslashes (\)
# or Unix-style forward slashes (/) as directory separators. Either
# way, all file references are on the ESP from which rEFInd was
# launched.
# Use of quotes around parameters causes them to be interpreted as
# one keyword, and for parsing of special characters (spaces, =, /,
# and #) to be disabled. This is useful mainly with the "options"
# keyword. Use of quotes around parameters that specify filenames is
# permissible, but you must then use backslashes instead of slashes,
# except when you must pass a forward slash to the loader, as when
# passing a root= option to a Linux kernel.
# Below are several sample boot stanzas. All are disabled by default.
# Find one similar to what you need, copy it, remove the "disabled" line,
# and adjust the entries to suit your needs.
# A sample entry for a Linux 3.3 kernel with its new EFI boot stub
# support on a filesystem called "KERNELS". This entry includes
# Linux-specific boot options and specification of an initial RAM disk.
# Note uses of Linux-style forward slashes, even in the initrd
# specification. Also note that a leading slash is optional in file
# specifications.
menuentry Linux {
icon EFI/refind/icons/os_linux.icns
volume KERNELS
loader bzImage-3.3.0-rc7
initrd initrd-3.3.0.img
options "ro root=UUID=5f96cafa-e0a7-4057-b18f-fa709db5b837"
disabled
# A sample entry for loading Ubuntu using its standard name for
# its GRUB 2 boot loader. Note uses of Linux-style forward slashes
menuentry Ubuntu {
loader /EFI/ubuntu/grubx64.efi
icon /EFI/refined/icons/os_linux.icns
disabled
# A minimal ELILO entry, which probably offers nothing that
# auto-detection can't accomplish.
menuentry "ELILO" {
loader \EFI\elilo\elilo.efi
disabled
# Like the ELILO entry, this one offers nothing that auto-detection
# can't do; but you might use it if you want to disable auto-detection
# but still boot Windows....
menuentry "Windows 7" {
loader \EFI\Microsoft\Boot\bootmgfw.efi
disabled
# EFI shells are programs just like boot loaders, and can be
# launched in the same way. You can pass a shell the name of a
# script that it's to run on the "options" line. The script
# could initialize hardware and then launch an OS, or it could
# do something entirely different.
menuentry "Windows via shell script" {
icon \EFI\refind\icons\os_win.icns
loader \EFI\tools\shell.efi
options "fs0:\EFI\tools\launch_windows.nsh"
disabled
# Mac OS is normally detected and run automatically; however,
# if you want to do something unusual, a manual boot stanza may
# be the way to do it. This one does nothing very unusual, but
# it may serve as a starting point. Note that you'll almost
# certainly need to change the "volume" line for this example
# to work.
menuentry "My Mac OS X" {
icon \EFI\refind\icons\os_mac.icns
volume "OS X boot"
loader \System\Library\CoreServices\boot.efi
disabled
Thanks for suggesting to try older ISO.
UPDATE:- Most recent ls -R /boot and my refind.conf. Reading over Rod Smith's rEFInd documentation has helped me clean up a little more and set up a good boot manager with automatic kernel detection and shell. I do want to get rid of drivers list that shows itself up along with kernel. Next is to tackle menu entry. Thanks.
Last edited by donniezazen (2013-04-04 06:43:16) -
Mac pro cannot boot after upgrade to 10.8.3
My Mac Pro cannot boot after upgrade to 10.8.3. Anything firmware I can reset or how should I do.
I am using a early 2008 Mac ProCan you boot into safe mode? http://support.apple.com/kb/ht1455
If not, how about Recovery? http://support.apple.com/kb/ht4718
If you can, run Disk Utlity and repair the disk. You can try rebooting normally, but I would just reinstall after quitting Disk Utility. -
How to load a Query in the bne_stored_sql in WEB ADI table.
Hi folks ,
I have a unique requirement as follow.
I have created an VIEW , which is given in the Download WEB ADI integrator defintion.
I am trying to query this view based in few search conditions thoughr a CO code. I am not used any time loading the Query in the bne_stored_sql table to achieve such funcaitonality.
Please folks any inputs on this would be greatly appricaited.
Thanks and Regards
RaghuHi,
I am creating the layout for a sales order which will be send to a customer.
In that order the customer can see the payment conditions.
It should look like this:
net price: 1000,00 EUR
19,00% taxes: 190,00 EUR
gross price: 1190,00 EUR
payment conditions:
payable within 30 days net: 1190,00 EUR
payable within 14 days with discount of 2 %: 1166,20 EUR
to get the bold marked digits I need to have access on the following tables:
OCTG and CDC1
In the OCTG table I get the days (in this example 30)
In the CDC1 table I get the days of cash discount and the percentage (in this example 14 and 2)
but in the sales order layout in PLD only the OCTG table is shown when I create a database field and the CDC1 table isn't.
So what can I do to get this? -
Arch & Windows 8 Dual Boot -- Windows Boot Loader loads grub-rescue
Arch works fine,but as it always happens Windows boot went down. Both OS are EFI.
Note that boot secure and fast boot were disabled for Windows 8.
I used os-prober, but did not fix anything; so, I removed it. I tried to hack things out using boot-repair from Ubuntu, but it requires a repository, grub-efi, from Ubuntu that Arch doesn't have.
I am trying to modify files in grub.d and grub.cfg and hopefully fix something.
Exact description:
- archgrub loads and shows 3 entries. Two for Arch that load the sys succesfully and one for Windows 8 that fails.
- When I try to execute Windows from grub, it brings me to a grub rescue>
and shows error /boot/grub/x86_64-efi/normal.mod not found
As far as I am concerned this .mod is from Linux, so I don't know why it is being called into Windows loading procedures.
lsblk returns:
[jav@localhost ~]$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 931.5G 0 disk
|-sda1 8:1 0 1000M 0 part
|-sda2 8:2 0 260M 0 part
|-sda3 8:3 0 1000M 0 part
|-sda4 8:4 0 128M 0 part
|-sda5 8:5 0 605.3G 0 part
|-sda6 8:6 0 5.4G 0 part /boot/efi
|-sda7 8:7 0 25G 0 part
|-sda8 8:8 0 20G 0 part
|-sda9 8:9 0 244.1G 0 part /
`-sda10 8:10 0 29.3G 0 part
sr0 11:0 1 1024M 0 rom
Here's the output of fdisk. Another weird thing is that sometimes ubuntu would show on my terminal. See the first line below, "jav@ubuntu"?!
[jav@ubuntu ~]$ sudo fdisk -l
[sudo] password for jav:
Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disklabel type: gpt
Disk identifier: [i deleted this]
Device Start End Size Type
/dev/sda1 2048 2050047 1000M Windows recovery environment
/dev/sda2 2050048 2582527 260M EFI System
/dev/sda3 2582528 4630527 1000M unknown
/dev/sda4 4630528 4892671 128M Microsoft reserved
/dev/sda5 4892672 1274335231 605.3G Microsoft basic data
/dev/sda6 1847777280 1859151871 5.4G EFI System
/dev/sda7 1859151872 1911580671 25G Microsoft basic data
/dev/sda8 1911580672 1953523711 20G Windows recovery environment
/dev/sda9 1335775232 1847777279 244.1G Linux filesystem
/dev/sda10 1274335232 1335775231 29.3G Microsoft basic data
And, bootinfoscript output:
Boot Info Script 0.61 [1 April 2012]
============================= Boot Info Summary: ===============================
=> No boot loader is installed in the MBR of /dev/sda.
sda1: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda2: __________________________________________________________________________
File system: vfat
Boot sector type: Windows 7: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/Boot/bkpbootx64.efi /efi/Boot/bootx64.efi
/efi/ubuntu/grubx64.efi
sda3: __________________________________________________________________________
File system: vfat
Boot sector type: Windows 7: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/Boot/bkpbootx64.efi /efi/Boot/bootx64.efi
/efi/ubuntu/grubx64.efi /bootmgr /boot/bcd
sda4: __________________________________________________________________________
File system:
Boot sector type: -
Boot sector info:
Mounting failed: mount: unknown filesystem type ''
sda5: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe
sda6: __________________________________________________________________________
File system: vfat
Boot sector type: SYSLINUX 6.02 ... :..(:,:0:4:8:....D:H:L:[.T:[.\:`:d:[.l:p:t:x:|:.:.:.:.:.:.:.:.....................
Boot sector info: Syslinux looks at sector 99102 of /dev/sda6 for its
second stage. SYSLINUX is installed in the /syslinux
directory. No errors found in the Boot Parameter Block.
Operating System:
Boot files: /grub/grub.cfg /syslinux/syslinux.cfg
/syslinux/ldlinux.sys
sda7: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda8: __________________________________________________________________________
File system: ntfs
Boot sector type: Windows Vista/7: NTFS
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files:
sda9: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Arch Linux ()
Boot files: /etc/fstab
sda10: _________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System:
Boot files:
============================ Drive/Partition Info: =============================
Drive: sda _____________________________________________________________________
Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Partition Boot Start Sector End Sector # of Sectors Id System
/dev/sda1 1 1,953,525,167 1,953,525,167 ee GPT
GUID Partition Table detected.
Partition Start Sector End Sector # of Sectors System
/dev/sda1 2,048 2,050,047 2,048,000 Windows Recovery Environment (Windows)
/dev/sda2 2,050,048 2,582,527 532,480 EFI System partition
/dev/sda3 2,582,528 4,630,527 2,048,000 -
/dev/sda4 4,630,528 4,892,671 262,144 Microsoft Reserved Partition (Windows)
/dev/sda5 4,892,672 1,274,335,231 1,269,442,560 Data partition (Windows/Linux)
/dev/sda6 1,847,777,280 1,859,151,871 11,374,592 EFI System partition
/dev/sda7 1,859,151,872 1,911,580,671 52,428,800 Data partition (Windows/Linux)
/dev/sda8 1,911,580,672 1,953,523,711 41,943,040 Windows Recovery Environment (Windows)
/dev/sda9 1,335,775,232 1,847,777,279 512,002,048 Data partition (Linux)
/dev/sda10 1,274,335,232 1,335,775,231 61,440,000 Data partition (Windows/Linux)
"blkid" output: ________________________________________________________________
Device UUID TYPE LABEL
/dev/sda1 CE62D9F062D9DCF1 ntfs WINRE_DRV
/dev/sda10 150a8788-6049-45ed-85af-ded92a2c0801 ext4
/dev/sda2 16DC-8816 vfat SYSTEM_DRV
/dev/sda3 7CDD-0403 vfat LRS_ESP
/dev/sda4
/dev/sda5 40E4E0CFE4E0C7EC ntfs Windows8_OS
/dev/sda6 9C3F-2A9E vfat
/dev/sda7 7240E43740E40427 ntfs LENOVO
/dev/sda8 422CE5EA2CE5D945 ntfs PBR_DRV
/dev/sda9 1a765403-f251-43d8-8edf-c191475d3837 ext4
================================ Mount points: =================================
Device Mount_Point Type Options
/dev/sda6 /boot vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/sda6 /boot/efi vfat (rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro)
/dev/sda9 / ext4 (rw,relatime,data=ordered)
============================= sda6/grub/grub.cfg: ==============================
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt9'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 1a765403-f251-43d8-8edf-c191475d3837
else
search --no-floppy --fs-uuid --set=root 1a765403-f251-43d8-8edf-c191475d3837
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
## Attempt at fixing grub
# insmod fat
# set root='hd0,gpt6'
### BEGIN /etc/grub.d/30_os-prober ###
#menuentry 'Windows Boot Manager (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-efi-16DC-8816' {
# insmod part_gpt
# insmod fat
# set root='hd0,gpt2'
# if [ x$feature_platform_search_hint = xy ]; then
# search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 16DC-8816
# else
# search --no-floppy --fs-uuid --set=root 16DC-8816
# fi
# chainloader /EFI/Microsoft/Boot/bootmgfw.efi
menuentry "Windows 8 UEFI" {
set root='(hd0,gpt2)'
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
### BEGIN /etc/grub.d/60_memtest86+ ###
### END /etc/grub.d/60_memtest86+ ###
========================= sda6/syslinux/syslinux.cfg: ==========================
# Config file for Syslinux -
# /boot/syslinux/syslinux.cfg
# Comboot modules:
# * menu.c32 - provides a text menu
# * vesamenu.c32 - provides a graphical menu
# * chain.c32 - chainload MBRs, partition boot sectors, Windows bootloaders
# * hdt.c32 - hardware detection tool
# * reboot.c32 - reboots the system
# To Use: Copy the respective files from /usr/lib/syslinux to /boot/syslinux.
# If /usr and /boot are on the same file system, symlink the files instead
# of copying them.
# If you do not use a menu, a 'boot:' prompt will be shown and the system
# will boot automatically after 5 seconds.
# Please review the wiki: https://wiki.archlinux.org/index.php/Syslinux
# The wiki provides further configuration examples
DEFAULT arch
PROMPT 0 # Set to 1 if you always want to display the boot: prompt
TIMEOUT 50
# You can create syslinux keymaps with the keytab-lilo tool
#KBDMAP de.ktl
# Menu Configuration
# Either menu.c32 or vesamenu32.c32 must be copied to /boot/syslinux
UI menu.c32
#UI vesamenu.c32
# Refer to http://syslinux.zytor.com/wiki/index.php/Doc/menu
MENU TITLE Arch Linux
#MENU BACKGROUND splash.png
MENU COLOR border 30;44 #40ffffff #a0000000 std
MENU COLOR title 1;36;44 #9033ccff #a0000000 std
MENU COLOR sel 7;37;40 #e0ffffff #20ffffff all
MENU COLOR unsel 37;44 #50ffffff #a0000000 std
MENU COLOR help 37;40 #c0ffffff #a0000000 std
MENU COLOR timeout_msg 37;40 #80ffffff #00000000 std
MENU COLOR timeout 1;37;40 #c0ffffff #00000000 std
MENU COLOR msg07 37;40 #90ffffff #a0000000 std
MENU COLOR tabmsg 31;40 #30ffffff #00000000 std
# boot sections follow
# TIP: If you want a 1024x768 framebuffer, add "vga=773" to your kernel line.
LABEL arch
MENU LABEL Arch Linux
LINUX ../vmlinuz-linux
APPEND root=/dev/sda3 rw
INITRD ../initramfs-linux.img
LABEL archfallback
MENU LABEL Arch Linux Fallback
LINUX ../vmlinuz-linux
APPEND root=/dev/sda3 rw
INITRD ../initramfs-linux-fallback.img
#LABEL windows
# MENU LABEL Windows
# COM32 chain.c32
# APPEND hd0 1
LABEL hdt
MENU LABEL HDT (Hardware Detection Tool)
COM32 hdt.c32
LABEL reboot
MENU LABEL Reboot
COM32 reboot.c32
LABEL poweroff
MENU LABEL Poweroff
COM32 poweroff.c32
=================== sda6: Location of files loaded by Grub: ====================
GiB - GB File Fragment(s)
================= sda6: Location of files loaded by Syslinux: ==================
GiB - GB File Fragment(s)
============== sda6: Version of COM32(R) files used by Syslinux: ===============
syslinux/cat.c32 : not a COM32/COM32R module
syslinux/chain.c32 : not a COM32/COM32R module
syslinux/cmd.c32 : not a COM32/COM32R module
syslinux/config.c32 : not a COM32/COM32R module
syslinux/cptime.c32 : not a COM32/COM32R module
syslinux/cpuid.c32 : not a COM32/COM32R module
syslinux/cpuidtest.c32 : not a COM32/COM32R module
syslinux/debug.c32 : not a COM32/COM32R module
syslinux/disk.c32 : not a COM32/COM32R module
syslinux/dmitest.c32 : not a COM32/COM32R module
syslinux/elf.c32 : not a COM32/COM32R module
syslinux/ethersel.c32 : not a COM32/COM32R module
syslinux/gfxboot.c32 : not a COM32/COM32R module
syslinux/gpxecmd.c32 : not a COM32/COM32R module
syslinux/hdt.c32 : not a COM32/COM32R module
syslinux/hexdump.c32 : not a COM32/COM32R module
syslinux/host.c32 : not a COM32/COM32R module
syslinux/ifcpu.c32 : not a COM32/COM32R module
syslinux/ifcpu64.c32 : not a COM32/COM32R module
syslinux/ifmemdsk.c32 : not a COM32/COM32R module
syslinux/ifplop.c32 : not a COM32/COM32R module
syslinux/kbdmap.c32 : not a COM32/COM32R module
syslinux/kontron_wdt.c32 : not a COM32/COM32R module
syslinux/ldlinux.c32 : not a COM32/COM32R module
syslinux/libcom32.c32 : not a COM32/COM32R module
syslinux/libgpl.c32 : not a COM32/COM32R module
syslinux/liblua.c32 : not a COM32/COM32R module
syslinux/libmenu.c32 : not a COM32/COM32R module
syslinux/libutil.c32 : not a COM32/COM32R module
syslinux/linux.c32 : not a COM32/COM32R module
syslinux/ls.c32 : not a COM32/COM32R module
syslinux/lua.c32 : not a COM32/COM32R module
syslinux/mboot.c32 : not a COM32/COM32R module
syslinux/meminfo.c32 : not a COM32/COM32R module
syslinux/menu.c32 : not a COM32/COM32R module
syslinux/pcitest.c32 : not a COM32/COM32R module
syslinux/pmload.c32 : not a COM32/COM32R module
syslinux/poweroff.c32 : not a COM32/COM32R module
syslinux/prdhcp.c32 : not a COM32/COM32R module
syslinux/pwd.c32 : not a COM32/COM32R module
syslinux/pxechn.c32 : not a COM32/COM32R module
syslinux/reboot.c32 : not a COM32/COM32R module
syslinux/rosh.c32 : not a COM32/COM32R module
syslinux/sanboot.c32 : not a COM32/COM32R module
syslinux/sdi.c32 : not a COM32/COM32R module
syslinux/sysdump.c32 : not a COM32/COM32R module
syslinux/vesainfo.c32 : not a COM32/COM32R module
syslinux/vesamenu.c32 : not a COM32/COM32R module
syslinux/vpdtest.c32 : not a COM32/COM32R module
syslinux/whichsys.c32 : not a COM32/COM32R module
syslinux/zzjson.c32 : not a COM32/COM32R module
=============================== sda9/etc/fstab: ================================
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
# /dev/sda9
UUID=1a765403-f251-43d8-8edf-c191475d3837 / ext4 rw,relatime,data=ordered 0 1
# /dev/sda6
#UUID=9C3F-2A9E /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
UUID=9C3F-2A9E /boot vfat defaults 0 2
UUID=9C3F-2A9E /boot/efi vfat defaults 0 1
============== sda9: Version of COM32(R) files used by Syslinux: ===============
boot/syslinux/cat.c32 : not a COM32/COM32R module
boot/syslinux/chain.c32 : not a COM32/COM32R module
boot/syslinux/cmd.c32 : not a COM32/COM32R module
boot/syslinux/config.c32 : not a COM32/COM32R module
boot/syslinux/cptime.c32 : not a COM32/COM32R module
boot/syslinux/cpuid.c32 : not a COM32/COM32R module
boot/syslinux/cpuidtest.c32 : not a COM32/COM32R module
boot/syslinux/debug.c32 : not a COM32/COM32R module
boot/syslinux/disk.c32 : not a COM32/COM32R module
boot/syslinux/dmitest.c32 : not a COM32/COM32R module
boot/syslinux/elf.c32 : not a COM32/COM32R module
boot/syslinux/ethersel.c32 : not a COM32/COM32R module
boot/syslinux/gfxboot.c32 : not a COM32/COM32R module
boot/syslinux/gpxecmd.c32 : not a COM32/COM32R module
boot/syslinux/hdt.c32 : not a COM32/COM32R module
boot/syslinux/hexdump.c32 : not a COM32/COM32R module
boot/syslinux/host.c32 : not a COM32/COM32R module
boot/syslinux/ifcpu.c32 : not a COM32/COM32R module
boot/syslinux/ifcpu64.c32 : not a COM32/COM32R module
boot/syslinux/ifmemdsk.c32 : not a COM32/COM32R module
boot/syslinux/ifplop.c32 : not a COM32/COM32R module
boot/syslinux/kbdmap.c32 : not a COM32/COM32R module
boot/syslinux/kontron_wdt.c32 : not a COM32/COM32R module
boot/syslinux/ldlinux.c32 : not a COM32/COM32R module
boot/syslinux/libcom32.c32 : not a COM32/COM32R module
boot/syslinux/libgpl.c32 : not a COM32/COM32R module
boot/syslinux/liblua.c32 : not a COM32/COM32R module
boot/syslinux/libmenu.c32 : not a COM32/COM32R module
boot/syslinux/libutil.c32 : not a COM32/COM32R module
boot/syslinux/linux.c32 : not a COM32/COM32R module
boot/syslinux/ls.c32 : not a COM32/COM32R module
boot/syslinux/lua.c32 : not a COM32/COM32R module
boot/syslinux/mboot.c32 : not a COM32/COM32R module
boot/syslinux/meminfo.c32 : not a COM32/COM32R module
boot/syslinux/menu.c32 : not a COM32/COM32R module
boot/syslinux/pcitest.c32 : not a COM32/COM32R module
boot/syslinux/pmload.c32 : not a COM32/COM32R module
boot/syslinux/poweroff.c32 : not a COM32/COM32R module
boot/syslinux/prdhcp.c32 : not a COM32/COM32R module
boot/syslinux/pwd.c32 : not a COM32/COM32R module
boot/syslinux/pxechn.c32 : not a COM32/COM32R module
boot/syslinux/reboot.c32 : not a COM32/COM32R module
boot/syslinux/rosh.c32 : not a COM32/COM32R module
boot/syslinux/sanboot.c32 : not a COM32/COM32R module
boot/syslinux/sdi.c32 : not a COM32/COM32R module
boot/syslinux/sysdump.c32 : not a COM32/COM32R module
boot/syslinux/vesainfo.c32 : not a COM32/COM32R module
boot/syslinux/vesamenu.c32 : not a COM32/COM32R module
boot/syslinux/vpdtest.c32 : not a COM32/COM32R module
boot/syslinux/whichsys.c32 : not a COM32/COM32R module
boot/syslinux/zzjson.c32 : not a COM32/COM32R module
======================== Unknown MBRs/Boot Sectors/etc: ========================
Unknown GPT Partiton Type
e7afbfbf4fa38a449a5b6213eb736c22
========= Devices which don't seem to have a corresponding hard drive: =========
sdb
=============================== StdErr Messages: ===============================
cat: /tmp/BootInfo-p9ML2Cte/Tmp_Log: No such file or directory
cat: /tmp/BootInfo-p9ML2Cte/Tmp_Log: No such file or directory
/dev/cdrom: open failed: No medium found
/dev/sdb: open failed: No medium found
No volume groups found
mdadm: No arrays found in config file or automatically
Any ideas?
Here's my grub.cfg:
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
if [ "${next_entry}" ] ; then
set default="${next_entry}"
set next_entry=
save_env next_entry
set boot_once=true
else
set default="0"
fi
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_gpt
insmod ext2
set root='hd0,gpt9'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt9 --hint-efi=hd0,gpt9 --hint-baremetal=ahci0,gpt9 1a765403-f251-43d8-8edf-c191475d3837
else
search --no-floppy --fs-uuid --set=root 1a765403-f251-43d8-8edf-c191475d3837
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=auto
load_video
insmod gfxterm
fi
terminal_input console
terminal_output gfxterm
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux.img
menuentry 'Arch Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-1a765403-f251-43d8-8edf-c191475d3837' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod fat
set root='hd0,gpt6'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt6 --hint-efi=hd0,gpt6 --hint-baremetal=ahci0,gpt6 9C3F-2A9E
else
search --no-floppy --fs-uuid --set=root 9C3F-2A9E
fi
echo 'Loading Linux core repo kernel ...'
linux /vmlinuz-linux root=UUID=1a765403-f251-43d8-8edf-c191475d3837 rw quiet
echo 'Loading initial ramdisk ...'
initrd /initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/20_linux_xen ###
### END /etc/grub.d/20_linux_xen ###
### BEGIN /etc/grub.d/30_os-prober ###
menuentry 'Windows Boot Manager (on /dev/sda2)' --class windows --class os $menuentry_id_option 'osprober-efi-16DC-8816' {
insmod part_gpt
insmod fat
set root='hd0,gpt2'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,gpt2 --hint-efi=hd0,gpt2 --hint-baremetal=ahci0,gpt2 16DC-8816
else
search --no-floppy --fs-uuid --set=root 16DC-8816
fi
chainloader /EFI/Microsoft/Boot/bootmgfw.efi
### END /etc/grub.d/30_os-prober ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
### END /etc/grub.d/40_custom ###
### BEGIN /etc/grub.d/41_custom ###
if [ -f ${config_directory}/custom.cfg ]; then
source ${config_directory}/custom.cfg
elif [ -z "${config_directory}" -a -f $prefix/custom.cfg ]; then
source $prefix/custom.cfg;
fi
### END /etc/grub.d/41_custom ###
### BEGIN /etc/grub.d/60_memtest86+ ###
### END /etc/grub.d/60_memtest86+ ###
Last edited by knowNothing23 (2013-12-30 00:17:02)Hi,
New to this forum, joined today in anticipation of trying an install of AL...For whatever this may be worth:
I have an HP Pavillion desktop that came with Windows 8 (now 8.1), & has, of course, a UEFI boot system. I tried earlier to install Ubuntu Studio (which I currently run) on the same disk as Windows (/dev/sda), I made (I believe) a huge mistake in trying to install as LVM/ext4... wiped out my Windows install & made the UEFI unavailable... I had to do a complete re-install of Windows (fortunately, I did the recommended system backup, using 4 DVD's!) so then I tried a (non LVM) install on an external usb 3.0, with the Grub 2 on the external disk (great access time, & it worked fine... IMO)...
One other item: as I have been trying to find the right flavor of Linux for my main purposes, I have been trying various distros. & having to try to learn to negotiate the UEFI, secure/legacy procedures (still learning)... As I was unsure of installing rEFind... I did down load the .iso, burn it to a CD...
http://www.rodsbooks.com/refind/getting.html
& in legacy mode, found that simply putting it (rEFind CD into the CD/DVD player, which in the UEFI it is labeled something like HP/UEFI CD/DVD), & then launching it, rEFind worked for some other distros...that is, I was able to boot into my Linux distros, even bypassing Grub), as well as having the option of booting Windows. It may seem trivial that I say this (it maybe is), but I have not seen anywhere (I have scoured the internet rather well) this mentioned as a possibility (though it, of course, would not make such a good permanent solution, especially for computers like mine that have only one CD/DVD player).
HenryP -
Bootcamp not showing up in boot loader
Today I needed to resize my Windows Vista Ultimate partition for work, so I used Disk Utility to crate an image from the partition. After that I used Boot Camp Assistant to remove the partition, and then create a larger partition. After this was done I went back into Disk Utility and restored the partition using the image I created earlier.
In OS X I can mount the partition and access the files and it seems everything was restored correctly. When I restart my machine and hold down the Option key to bring up the boot loader, Bootcamp is no longer an option. The only partition I can boot from is HD.
Please help! ThanksDid you actually Install a version of Windows into that Boot Camp Partition? It doesn't sound like you did.
You'll need a copy of Windows 7 or 8, 64bit, and a valid license key code for whatever version you plan on installing.
Ethan_Fidler wrote:
I have sucessfully partitioned my macbook pro (thanks Ds Store!) and now I have another problem, When booting up I hold down option to choose my startup disc all that shows up is macintosh HD and recovery, BOOTCAMP is not showing up, even though it showes up in devices please help me!!
- Ethan -
Cannot mount Windows partition with boot loader on Mac OS 10.8
I took out my hard drive of my Windows 7 PC, which has 3 partitions on it: C drive which contains the OS and the boot loader that the computer boots into, D drive which contains my data, and a third called "System Reserved" a few megabyte in size that I have no idea what so ever what it does besides that I cannot modify or delete it, which probably means that it is important. Now I put the hard drive inside an USB 3.0 enclosure and I am trying to mount this hard drive onto my OS X Lion Macbook air. Something strange is happening, in that the computer takes about 30 seconds or more to detect the drives presence, and then it just freezes after that. On the initial try, the system actually successfully launched DiskUtility, and I can see the drive mounted in the list of detected drives and 3 partitions "SD1, SD2, SD3" under that drive, but after repeating the procedure a few more times, nothing seems to be happening after the system freeze.
Anyone have any idea what's going on? I am trying to access the data partition for my stuff.
I have Tuxera NTFS installed, and I should probably also mention that my Macbook Air is mid 2011 with only USB 2.0 ports.
Thanks in advance.Ok, I figured out the freezing part; apparently, I had to connect to the USB port on the left side next to the power supply or the disk does not have enough power and causes the system to crash. So, now Disk Utility can see the hard drive with no problem.
But now, the partitions are detected as XFAT format and no volumes are mounted to the desktop. Disk Utility displays the disk description as:
Disk Description : INTEL SS DSA2M160G2GC Media Total Capacity : 160.04 GB (160,041,885,696 Bytes)
Connection Bus : USB Write Status : Read/Write
Connection Type : External S.M.A.R.T. Status : Not Supported
USB Serial Number : CVPO049000W0160AGN Partition Map Scheme : Master Boot Record
Why is the status "not supported"? How should I go about mounting the data volume so I can access the files on my Mac? -
Error in adding attachment to the workitem. load:class Query.class not foun
Hi,
We are using WebGui to access the Business Workplace(SBWP transaction) through Portal. For any work item, when i try to import a file from the local PC, i get a screen with the header -"Enter Some FIle attributes". Text displayed in the screen is "Please wait. You will be forwarded automatically. This page had to be included for techincal reasons". And i am struck in that screen. I believe a java popup winddow should come up at this point to select the PC File but it never happened. The screen also has a status message "
Loading Java applet failed. Applet Query.class not inited ".
WHen i look at the java console, i find the following error trace. Please let me know if anybody experienced this problem before and how to fix it. Thanks for the help.
Trace ---
load: class Query.class not found.
java.lang.ClassNotFoundException: Query.class
at sun.applet.AppletClassLoader.findClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at sun.applet.AppletClassLoader.loadClass(Unknown Source)
at java.lang.ClassLoader.loadClass(Unknown Source)
at sun.applet.AppletClassLoader.loadCode(Unknown Source)
at sun.applet.AppletPanel.createApplet(Unknown Source)
at sun.plugin.AppletViewer.createApplet(Unknown Source)
at sun.applet.AppletPanel.runLoader(Unknown Source)
at sun.applet.AppletPanel.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Caused by: java.io.IOException: open HTTP connection failed.
at sun.applet.AppletClassLoader.getBytes(Unknown Source)
at sun.applet.AppletClassLoader.access$100(Unknown Source)
at sun.applet.AppletClassLoader$1.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
... 10 more
Regards
hariHi all,
I have encountered same problem in ITS 6.20.
Query.class is packed in ws.jar which is stored at C:\Inetpub\wwwroot\<SID>\sap\its\mimes\webgui\99\applets and C:\Inetpub\wwwroot\<SID>\sap\its\mimes\webgui\2002\applets in ITS server.
I increased the trace level to 3 in the Java console to inevestigate the problem further.
== Java console (Trace level 3 ) ===
network: cache entry not found URL: https://hostname.domain.co.jp:443/sap/its/mimes/webgui/2002/applets/ws.jar、version: null
network: Connect to https://hostname.domain.co.jp:443/sap/its/mimes/webgui/2002/applets/ws.jar (Proxy=DIRECT)
network: Connect to http://hostname.domain.co.jp:443/ (Proxy=DIRECT)
java.net.ConnectException: Connection refused: connect
load: class Query.class not found.
java.lang.ClassNotFoundException: Query.class
==========================
Then I found out that when system tried to load class Qery.class the connection to ITS was refused becase the incorrect protocol ( https ) was chosen. In my case, SSL was not setup, therefore protocol must be http.
I activated http by changing the configuration file for WGate in C:\Program Files\SAP\ITS\6.20\config\ ItsRegistryWGATE.xml
After that, I restarted the WGate by accessing to http://hoostname.domain.co.jp:port/scripts/wgate/wgate-restart to activate the configuration.
And also I restarted the AGate by restarting the Windows Service "SAP ITS Manager - <SID>".
Anyway, the html (BHTML) file that displays the message below is stored at C:\Program Files\SAP\ITS\620\templates\system\dm\itsdoc.html
"Please Wait. You will be forwarded automatically"
"This page has been loaded due to technical Reasons"
Best regards,
Akira -
Error installing grub boot loader
I am currently following the beginner guide for installing arch, and once I get to the place where I need to install a boot loader and use the command pacman -S grub-bios, I get a seemingly never ending output of "sh: /usr/bin/wget: no such file or directory" then it will change to "warning: failed to retrieve some files from core"(more like all files lol) etc as it goes through the repos. I've followed the guide to a tee, with the exception of the example partitioning on there. Anyone have any ideas on what could be going wrong?
It seems like wget is missing on the install partition. This is after you have done arch-chroot right?
I would try to do a
# pacman -Syy wget
to update the archive and install wget
and then try grub-bios again
edit:
If you are still on the install media the command you want to use is
# pacstrap /mnt grub-bios
Last edited by drobole (2012-12-16 11:47:49)
Maybe you are looking for
-
Hi, After running some updates yesterday, the "show text input options" is no longer available in the options. Neither can I select suretype when writing a message. Would appreciate some help. Thanks Solved! Go to Solution.
-
Hello all, I'm currently house sitting for a friend whilst she's away and all of a sudden all (3) of the TV's just say 'no signal' when I switch them on-It started yesterday with the one in the lounge (whilst the one in my bedroom worked fine last ni
-
Failed to retrieve data from the database. Details: [Database Vendor .....
Hello, I hope that is the right forum for this issue. We have the application 'Lodestar' for some years. The frond-end is ASP and the database is Oracle 9. Lodestar has its own backend language "Rules language". The crystal version is 10 Now we have
-
Is the ABAP Webdynpro CATS available in both ESS and MSS?
Hi experts, We are in the process of implementing the WDA CATS application for ESS (ECC 6 EHP5) but our scenario is actually for managers to enter in time in CATS on behalf of their employees. I can't find any information on this scenario using the W
-
Convert PDF to Microsoft Powerpoint
I cant find where to comvert PDF to Powerpoint, I have word and excel