Boot problem with 745 ultra MB

I am having a problem with a computer I am building. Everything is installed right but when i boot (even at default) it freezes up and gives this wierd big orangeish text in the upper left of the screen. Here is what is in the computer.
Msi 745 ultra X(
1700+xp retail cpu with amd approved fan
evga gforce2 mx200 32 mb
512 ddr ram
40 GB maxtor Hard drive
smartlink 56k modem
If anybody could PLEASE respond to this with some advice i would be much appreciated.
Kolmstead 8) X(

Quote
Originally posted by Paca
hi
I was told to remove my jumpers and do a clean install.
What if I simply remove the jumper (it is on the "master" position), won't the system work properly ?
thanks
Paca
yes, the system work properly. I use two 40GB WD drives, try to working but no luck. thank wonkanoby told me to remove pin from both WD. It run great I know it sound silly but it working ok.

Similar Messages

Poll: Do you have cold boot problem with SB X-FI Fatal1t

Hi guys:
I have post a thread regarding the cold boot problem with SB X-FI Fatalty and OCZ GameXStream 600W SLI power supply combination. Apparently, no one has answer to that . In addition, I have recently RMA'd my psu and received a brand-new unit. The same problem still exists. If the problem is really with the power supply, doesn't matter what kind of the setup I have, I should still have the cold-boot problem. However, it doesn't seem like that. Doesn't matter what kind of cards I put on the motherboard, as long as the SB X-FI Fatalty card is there, there is cold boot problem (even with the setup of cpu, mother, ram, and the sound card only, WITHOUT video card and harddri've). And for other different setup without the SB X-FI Fatalty card, there is no cold boot. The cpu and memory are running at stock speed.
My post regarding the cold boot issue:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=79753
There is one user on the forum saying he has the same problem. Therefore, I think it might be the imcompatibility between the X-FI Fatalty and OCZ GameXStream PSU.
I would like to know how many people that has the same problem that I am having. So I can possibly narrow down the problem and contact OCZ tech support or creative tech support with more information. It would also be benefitical to those who have the same problem as I do.
Please post your system setup as well in the thread.
Greatly appreciate your opinions. Message Edited by White_Hair on 2-02-200604:58 AM
Message Edited by White_Hair on 2-02-200603:22 PM

I would venture to say that it isn't your powersupply, but more likely the X-Fi. I had troubles with my system, until I pulled out my X-Fi and replaced it with a non Creative Labs sound card. One of my troubles, which I incorrectly blamed on my powersupply was the ASUS A8R-MVP motherboard I had and the X-Fi XtremeMusic card, was after gaming for 4 hours, was the?sudden reboot of my system. Powersupply before, was an Antec TrueControl 2 550watt PSU. As it stands right now, I no longer have the parts mentioned and have a decent 700watt powersupply in my system, along with an ABIT AT8 32X motherboard. As you have probably seen there are a lot of problems with the X-Fi soundcards, and I in my right mind can't blame the motherboard, powersupply, motherboard chipset, ram, or any other component in ones system, if one is having trouble other than the X-Fi itself. I'll be honest, there is something quite frankly wrong with the X-Fi, and exactly what that is, I'll probably never know like most people.

K8N NEO4 Platinum cold boot problem with 165 opteron?

I have this board and have a cold boot problem with my opteron. Is there anything I can do to fix this? Its starting to get very anooying.
K8N NEO4 Platinum
165 opty dual core
2X1GB Ballistix PC4000
160GB sata2
7800GTX
X-Fi platinum
600 watt seasonic PSU

Well I am running them at the rated speed of 250 and the rated timings of 3-4-4-10 on the rated 2.8 volts. Ballistix have been known to die quickly when you throw to many volts at them for some reason. I dont get the cold boot problem with the OCZ. Once I finally get it to boot with the Ballistix it works just fine but the next morning I play hell to get it to boot again. I dont even get the main screen to let me get into bios. It just stays black. I have done all kinds of stress testing and ran memtest with no problems. I am really at a loss here.

Desire no keyboard booting with 745 Ultra

I've got:
Mobo: MSI 745ULTRA SIS745 DDR333 ATX
Proc: AMD Athlon XP2100+
MEM: Corsair 256 MB DDR2700 at 333 MHz FSB x 2
Vid: PNY Tech. GeForce 4 Ti4600
HD: Western Digital 40 Gig
Optic: OptoRite DVD/CD +/-R/RW
Trying to get Microsoft BlueTooth Keyboard and Mouse setup. Got these working but can not disconnect the PS/2 Keyboard from the system. When I do and try to reboot it halts on no keyboard detection.
Going through CMOS/BIOS settings I can not locate a "Halt - All/None" setting I find on all my other systems. Going through "Live Update 3" I've updated all drivers and BIOS. The update didn't add anything to my setting options.
How do I make it so this 745 Ultra mobo system does not require a detectable/detected keyboard?
Thank you all ahead of time.
Seize the moment!
Cheerios,
Brian

From all indications; manual, FAQ, and msg boards ... this particular motherboard requires a keyboard to boot up. MSI in their infinite wisdom has not yet added the "Hault On" option to the 745 Ultra mobo BIOS/CMOS options.
This sucks as I now have a bluetooth keyboard and mouse that I won't be using on this machine and will instead be using a wired unit. So much for making my need to move the system around easier
Anyone know of a null keyboard loop type of thing I can slap onto the PS/2 keyboard port to fake the system out, make it think there is a keyboard on the system so once it has booted up the bluetooth keyboard can then be used? Anyone?
If so thank you ahead of time if not ... someone in MSI make one for these mobo's you were short sighted on!
Cheerios,
Brian

Problem with K9N Ultra and Windows 7!!

Hello,
I have the following system:
- K9N Ultra (MS7250 - Version:2.0)
- AMD Athlon 64 3500+
- 4x Kingston KVR533D2N4/512
- NVIDIA GForce 7300GS
- Seagate Baracuda: ST3120827AS (7200rpm)
- NEC DVDRW ND4571A
I am running Windows XP SP3 but when I try to install Windows 7 (either 32 or 64 bit versions), when the system boots up, I choose to run from CD/DVD, the files are being loaded in the beginning but then the system is stuck in the next screen where it says Starting Windows with the green bar. I have left it for up to 90 minutes and it remains there, no change. I have tried with several different disks, always the same. I tried disabling legacy USB drivers, disabling on board audio, disabling USB and having a normal keyboard and mouse, always the same, no change whatsoever, the system halts at the same point every time.
Can someone please offer some help?

i tried once more, again disabling onboard audio, legacy, floppy, everything.....same thing, when the files are loaded and the screen goes at the green bar, the DVD spins down and halts there for ever.
i am really pissed with this problem. i have installed windows 7 in all of my computers and this is the only one that absolutely refuses for windows 7 to be installed!
hmm..what do you mean about the PSU? why would the installation of 7 have a problem with the PSU? 2 days ago i installed again windpws xp sp3 (just to see if they would install in contrast to 7) without a problem. i am really tired of changing keyboards, DVDs, taking RAM in and out etc to it...i could live without the need to take a PSU out of another pc and install it to that one, is there some BIOS fix for the problem you mention?
the bios is version 3.00 from what i read.
also..what is nvidia boot agent that is the fourth option of boot in my bios??

Boot Problem with K8n Neo 2 Platinum

I cant get my Computer to load the bios
Sometimes when I restart my computer it will lock up in the Bios Sign on and the only way to get it to boot through is to keep resetting the computer and turning the power off and on. It does this on a random basis, Ive also had problems with it locking up if the dynamic oc is turned on.
Has anybody heard of this happening or know how to fix it?
MSI K8N Neo 2 Platinum Bios 1.4
Athlon64 3800+
TwinX 1024 3200LLPRO
Xtasy 9600XT
Ultra Products X-Connect 500w
2x WD Raptor 10,000rpm SATA HD in Raid 0 cfg
SB audigy 2 ZS
LiteOn cd/dvd drive
LiteOn dvd burner
Windows XP SP2

Corsair memory is known to be troublesome with AMD64.
Nevertheless, if everything is set correctly, it'll work. I've been running the LLPRO 3200 1GB kit at 220MHz without any noticable problems. Run a couple of rounds with Memtest86+ to verify memory functionality.
Can you please give your specifications on the power supply unit (PSU), especially the amperage on the +12 volt rail.
Anders.

Big problem with KT3 Ultra (ms-6380e v1.0) after flashing the BIOS (de

Hello out there.
I have a real complicated matter with my Kt3 Ultra board.
Used to work fine, but after I flashed it with the latest BIOS (5.7), the board has this strange behaviour: when I clear the CMOS, the board boots up, when I change & save the settings, the board does not "come to life"(black screen & beeper silent).
It has also this weird problem: it shows garbage charaters on the voltage setting of the CPU. Instead of voltages (i.e. 1.750 etc. etc.) I have only "scrambled" strings.
I had MANY difficulties in upgrading the BIOS because the AMI-flashing utility kept telling me "bios protection enabled) (but there was NO bios-protect setting in the previous bios - I checked a zillion times)...but after trying with different revisions finally I made it.
I already tried everything (re-flashed older bios-es etc. etc.)and I'm starting to feel beat ... if you have any advice, please le me know.
It would be really SAD to put this great board in the garbage-dump....
Bye,
Wyk'03

im having problems with this board as well,
i had no problems with the flash,
i did this...
boot to win me floppy,
copy the flash files to ramdrive, flashed to latest bios..
now windows hangs when i have my ac97 audio enabled in bios...
I WANT MY AC97!
hmmm can you get to a dos prompt from a boot disk?
try re-flashing with 1.0 again and then disable the cmos virus protection thingy, and yes it was there it was in the 1.0 bios on the main screen.

PC2700 incompatible with 745 Ultra?

I've been running my MSI 745 Ultra with two 256MB sticks of pc2100 (266mhz Kingston Value Ram) for two years trouble -free. I love this board. Last week I bought a new 512MB stick of pc2700 (333mhz) Kingston Value Ram and the computer randomly crashes. Pulled out the two original sticks and just ran the new 512MB stick alone, still crashes. Bought another 512MB Kinston Value stick and more crashes. Bought a Kingston Value 1GB stick, more crashes.
Calls to MSI and Kingston confirm that my board should work with Kingston Value pc2700, so they're stumped.
When I run any pc2700 stick alone, the CAS latency gets set to 2 (the ram is 2.5). I set it manually to 2.5 but still crashes. When I run the pc2100 memory, the bios posts a correct 2.5 CAS latency.
Running the FSB at 1:1 ratio or 4:5 ratio(with the pc2700 stick alone) makes no difference.
Anyone with a the same board running pc2700 ram trouble-free? Suggestions?
MSI 745 ultra
Kingston Value 256MB pc2100 X 2
NVidia MX440-p video (4X AGP, dual-video out)
Duro 400-watt PS (+3.3v 28A, +5v 30A, +12v 11A, +5vsb 3A)
WD 120GB HD, 7200 rpm

You don't have a fever for sure! But maybe a cold?
Thank you very much for the readings!
I do want it to be compatible. For some reason it is probably not. However, the "long" time for it to become problematic, makes me think it i s compatible. My thinking shouldn't make you take all kinds of trouble fixing and dealing and searching, but does the freeze-bsod-crash-reboom also happen in SafeMode? In that mode, as you know, there will not be more than the basic windows drivers and not much in the background.
Strange that the CAS setting wont "take". Try it the other way around, and set to "3".
Adding: Perhaps I missed a lot. I searched the Internet for your error message, and mostly came up with sort of software or settings related problems. Not that it were that many hits for the search.
Here is a half-way related example from http://66.249.93.104/search?q=cache:lM9Sgu_fxLYJ:trillian.cc/forums/showthread.php%3Fs%3Df30c169d510191ea7102e3ac168431f0%26postid%3D341840+%22dumping+virtual+memory%22&hl=sv:
"ok..like we are asking strange questions,
Maybe we all have seen a blue screen before right? surely with Xp..(home or Pro)..where it said ...alot of nonsense..and then...dumping virtual memory...
ok, we all now to go to the source to see why it does that, most of the times was my video card that did it, but after a while, my Rimm (rams)..began doing the same..and I'm a guy that experiments alot so I do everything myself,..fine after a few trail and errors it got working..now here comes the two questions
Why sometimes, I had to change my modem from it slot.?? so it can be seen by the PC...and sometimes I have to change like 3 to 5 time to get it working..
this happens everything I have to format or install a new harddrive..and sometime I change it..back to the same slot where I began...so make nonsense to me...and last time, I had to play the rams so I can get the modem to work, does that make any sense..
and the other question is,
Ihave a logitech Quick Cam, the first time I installed it on my pc..with Xp Pro..it worked fine,didn't have to unplug and plug it in (making sure I restart the pc without it plugged in)..so It can work..but after I formatted the HDD..once..I have to do all those things to get it working...why?
thanls
-=LT=-

Fsb problem with Neo4 Ultra

I have been having a problem with my neo4 ultra that seems to be pretty common.
I can not boot past a fsb of 219 reliably.
My system is
AMD64 3200+
MSI K8N Neo4 nForce4 Ultra
Wavemaster Case
OCZ Gold Series Dual 1GB DDR PC-3200
Thermalright XP-90
OCZ ModStream 520W
Sapphire Radeon X800 XL
I am doing it all with clockgen to up my FSB to find the best results. I am on 1.24 BIOS
My Basic BIOS settings are
FSB = 219
HTT = 4x
Mem at 166 Voltage at 2.85
Mem Timmings at 2.5-3-2-8 1T
CPU 10x startup - cpu-z reports voltage at 1.58
Rasied FSB by 5 at a time to 251 and super pi failed.
Changed vcore to 1.60 and the best I could get super pi to run at was 247. So I decided to start fine tunning my memory.
I set mem to 180 2.5-3-3-10-1T
Used clockgen again and what was interesting was FSB of 255 passed with a superpi of 34 sec. Now it failed at fsb258.
Changed mem timmings to 200 2.5-3-3-10-1T
And best I could get was fsb=230 and superpi failed. I decided to keet the 180 divider and see how far I can drop the timming at 180.
So I ended up at this
FSB =251
HTT 4x
Mem 180 2-3-2-8 1T volts = 2.85
CPU 10x Volts cpu-z reports 1.63
Runs prime stable all night at these settings.
But here is the thing if I go into the BIOS and change fsb to 221 My machine will not boot.
I am guessing the power up sequence is wrong in the BIOS

I cannot boot at over FSB 219, either. Will overclock fine with Clockgen when in XP (have tried up to 270 fsb, and the CPU will run 2574mhz at 1.5). But have to reset bios if I set the FSB over 219, regardless of memory HTT, vcore, etc , settings. I've been watching other forums and have seen MANY people with the same problem. One of the things I have in common with a lot of other people with this problem is that my Winnie 3500+ Retail will not run much over stock with the low vcore that this board gives as default. I have used Core Center, Sisoft Sandra 2005, and CPUz 1.27 to check vcore once in windows. All of them show 1.36 for vcore. That's lower than default of 1.4. And when I set the vcore for 1.55 and the overvoltage thingy to highest percentage in bios, all the monitoring apps show 1.526, which is waaay lower than it should be (1.67). Now, I will concede that the monitoring apps could be wrong. But, I believe the 219mhz POST issue is due to the start up vcore and multiplier is PROBABLY default at post. So, if your FSB is set for more than the CPU will run at it's default vcore and multiplie + set FSB, then the board freezies at POST. If the bios would just boot at whatever you set into the bios, then there wouldn't be a problem, unless yoiu have set thingswaay too high. Then it would just do what it does now, not POST, and you would have to reset the bios. There are a lot of Winchester core CPU's out there that will run high mhz at default voltages. But, there are a lot of newer Winnie's that won't. Mine is one of them.
Now it seems that there is a limitation on the board of 1.55 vcore with a Winnie. Even using the overvoltage setting. What is that all about? You put overclocking friendly on the retail box, on the product page on the main site, and all the review sites say overclocking potential is graet, and then you limit the vcore to 1.5v? Crazy logic (or should I say "Fuzzy Logic") I am close to eBaying this board (only had it 2 - 3 days, but won't send it back to ZZF for replacement as all of them could have the same problem) and go with the DFI or the Abit Fatality.
Am I saying all this right?

Boot problems with K8N Neo FSR

Recently i bought a new MSI K8N Neo FSR mainboard and an Athlon64 3000+
I noticed that a lot of people on this board had problems when booting Windows XP
I had the same problem: Every time i tried to boot Win, it freezed at the Win XP logo.
It seems that the problem is my cordless logitech keyboard.
When i'm using a standard PS/2 keyboard i have no problems booting.
Are there any known problems with nForce3 based mainboards and cordless logitech keyboards?
Does anyone know if there is a way to fix this problem?

There just seems a problem with some mobos and keyboards.
Usually it's a PS2 thing, but looks like you have found another to add to the list.
Note...
COMPATIBLE INPUT DEVICES (Keyboards)
Aspire/Mitsuko Internet Keyboard
Cherry Soft Touch
Chicony #KB-9805
Compaq EVO Series
CoolerMaster Q
Dell
Logitech Cordless Duo, Logitech Ultra-X, Logitech Internet Navigator
Logitech Di Novo Series
Memorex Multimedia
Microsoft Multimedia Wireless, Microsoft Desktop Elite
Mitsumi #KFKEB9HY
Qtronix Scorpius
Viewmate Office

Cd rom boot problems with MEGA 180

I recently recieved my MEGA 180 and have been unable to successfully install an OS because when I boot from CD, the computer freezes at various stages of installation. The point at which it freezes varies between the point at which the CD is initialized to anywhere in the windows xp setup process up untill the drive format. Occassionally the lockup coincides with an error copying a file, but this is not consistent. I have tried two different cd-rom drives as well as three different xp installation cds. Further I have run with 5 different sticks of ram (kingston and corsair). None of these changes have had any obvious effect.
Having read the warning labes regarding non MSI optical devices, I am tempted to think that may be the problem as I am not running on an MSI drive. However, the warning souned like it was about mechanical parts and thus I assume the ability of a drive to fit in the MEGA 180 case while opening and closing correctly.
I would appreciate any input you might have on this matter as I am finding this experience rather frustrating.

I had the exact same problem when upgrading from a 2100+ Palamino processor to a 2800+ Thoroghbred one. The screen had already dissappeared due to powering up with no monitor plugged in, so I tried a reinstall of Windows XP. It kept falling over randomly during the install process. I then swapper the CPU back and had no problems at all. I have since lapped the heatsink and reduced the FSB to 157MHz in the BIOS, and have not had a problem with the 2800+ CPU. I have not tried installing windows again, but feel this will be OK too.
My test is to run FujiFilm Snapshot Slideshow, which sends the CPU temp rocketting. I have found that when it goes above 70 C it starts getting unstable. I throttled the FSB back to 157MHz and it does not get to 70 C any more. In normal operation it never gets above 60 C, so I don't know why the slideshow takes so much CPU power

Problem with KT4 Ultra and XP 2700

First excuse my bad english (i'm from Germany)!!
I have a heavy problem with my KT4 Ultra.
First my system:
AMD Athlon XP 2700
Mainboard: MSI KT4 Ultra (MS-6590) Bios vers. 1.1
MSI Geforce 4 Ti 4200 64 Mb
512 Mb DDR Ram Apacer Technology 512 MB 16x(32mx8)DDR-SDRAM PC2700U-2533-700(CL2.5 upto 167MHz)(CL2 upto 133MHz
Sound : Onboard
GlobalWIN CAK38 II Kupfer
Powersupply: Levicom 420W
Win XP SP1
Now the problen:
When i turn the FSB in the Bios up to 166MHz
the system crashes on Windows startupscreen!!
I've turned the FSP clock down to 164 MHz and Windows starts.But when i runned 3DMark2001 it crashes back to desktop !!
Then i turned the FSB clock down to 159 MHz and the system runns stabile!!
Now what i've already tried:
Turned down Ram timings and frequency (same prob.)
No heatproblem (CPU at 118.f)
Had the same system exapt an XP1800 instead an XP2700 and no problems!!
Called the MSI hotline (Germany) and they told me to type the FSB manually in the Bios (insted of numblock +and -). ?(
Still the same problem !! ;(
Has anyone the same problem as i ???
THX !!

Hi,
I would try other ram....
Or start from BIOS default settings and only change CPU-FSB....
See what happens...

Boot problem with new HD

I have just bought a new HD (WD 120GB SE, ATA100, 8MB CACHE) for my PC. My old HD was a Quantum Fireball Plus AS 20.5GB. I had in mind to remove the old one and copy the 2 partitions from the old one to the new (3 Partitions made by Partition Magic). I used the Norton Ghost 9 to copy the partitions with the "copy one drive to another' option, also select the one partition to be "active" so it can boot the OS and copy the "master boot records" from the old HD. When i restart the PC with the new HD as master after the "veryfing DMI pool data" i should see the windows logo with the loading bar, but the only thing i get is under the "veryfing DMI pool data" the message "error loading operating system"! ! ! The same thing happens if i copy the partition (with the OS) to a dvd again with Norton Ghost and try to recover it. And the strangest thing is that i have the same problem if i try to install (clean) windows to the HD, it copies some files to the HD and when it restarts so it can continue installing windows shows the same message. I have download a diagnostic program from WD and there is no problem with the HD. I have taken the HD to a friend of mine and it works fine. I forgot to mention that both bios and windows detect the HD. When i use the HD as slave, i can copy/cut files/folders with no problem in windows. I have the latest ver. of bios and nForce drivers. PLEASE HELP ME! ! !!
P.S. Sorry for my english. . .

If you use Ghost to copy from one disk to another and the geometry is different, it can happen that the result is not readable.
Simple way: plug disk as slave. Boot on the 20GB drive. Partition the new drive in windows. Copy the files.in windows. Activate the new partition as primary and bootable. Swap drives.

My Mac Pro 1,1 won't boot, problems with disk.

I am having problems booting my 2006 Mac Pro 1,1. I was using my computer just fine and then I shut the computer down. When I tried to restart it the computer booted the the Apple logo and the status whell began turning, and then a progress bar appears under that and begins to load. It loads about 1/10 of the way, dissappears and then the computer shuts off.
I booted the computer using Command + R and attempted to reinstall OSX Lion, but it would not allow me to select a drive to install too. They are all grayed out. From here I went into Disk Utility and attempted to Verify Disk Permissions. A laundry list of errors immediatly came up. Next step was the verify the disk, at which point the message read that the disk seamed to be corrupted and needed to be repaired. I tried to repair the disk but was then told that the disk couldn't be repaired, to recover any data and reformat the drive.
The problem with this is that I have not backed anything up (yes I know I am a TARD) but this is my situation and I need some help. At this point I would just like to recover the info that's on this disk, and without a computer to do this I'm not sure how to do this. At this moment I am attempting to make a disk image of the corrupted drive in hopes that this will allow me to restore it later.
Please somebody help. I bought this computer with a lot of pre-installed programs, (i.e Adobe Creative Suite, Final Cut Studio, etc.) not to mention all of my other files.

I have an external drive that I used to keep files backup up on, again I'm a TARD, and no longer do. I've been messing around with the Recovery option when I boot and during this venture saw my main HD unmount and just would not do anything. After trying a few things I reset the system again and when I got back to recovery noticed that the drive had mounted again. I am now using disk utility to copy the entire contents of this main HD to the external drive. Est. time remaining is 12 hours. I did have the external filled up with some stuff but nothing I wasn't willing to trade for all of my applications (that came pre-installled when I bought the machine) and other files. I've read that even doing this isn't a fail proof way to solve the problem as their are still corrupted files, but Disk Utility said that my drive couldn't be repaired and to backup what I could and format the drive. I am hoping that backing up everything to this external drive will give me at least some oportunity to recover my apps, files etc. It also said that if disk utility couldn't fix the drive to boot from the CD and try it that way. Unfortunatly I downloaded Lion and don't have one. I just bought this HD about 2 years ago. Is a Seagate and I haven't had any problems from it. When my computer stopped working I had just been using it and just reset the computer. I am definitly going to get another drive but what are your thoughts on my ability to recover everything? I've heard there are some programs that can handle it.

Cold boot problem with X-FI Fata1ty card... Need serious help!

Hey guys:
I just finished upgrading my computer. Realized that I have a cold boot problem. In order to identify the source of problem. I began the following test.
. Remove everything except, cpu, heatsink, ram, video card. Tried to boot with those devices. => No cold boot problem.
2. Install the rest of the ram sticks (I have 4 x 52 in total). => No cold boot problem.
3. Install the other video card (my setup is 7900gtx in SLI) => No cold boot problem.
4. Install the Creative X-FI Fataty card. => COLD BOOT PROBLEM
Once the computer is shut down via the front power switch on the case, the computer will not boot again. To boot the computer, I need to switch off the main power switch on the back of the psu and switch it back on; then turn on the computer via the front power switch on the case. I tried the problem with and without the sound card. Whenever the sound card is installed. There is the problem. If there is no that sound card in my rig, then there won't be any cold-boot problem.
My rig specs:
DFI Lanparty nF4 SLI-DR Venus
AMD Opteron 65 CCBE 609 - Stock speed
4 x 52 MB G.Skill Samsung TCCD LE 2.85V DDR 400
CPU Cooling - Tuniq tower 20
2 x EVGA 7900 GTX Stock - SLI
3 x WD Raptor 74G RAID-0 SATA (-3) 0000 rpm (System)
x Seagate Barracuda 7200.7 60Gb 7200RPM NCQ SATA - 4 (Backup)
Pioneer Black DVR 0 DVD+/-RW - IDE /0
Lian-li PC-V 200B Plus-2 with little case mod
OCZ GameXstream 600W
Creative Fatalty Sound Card w/ Front Panel
Logitech Z5500 5. speakers
I need serious help. This problem is so annoying.
Tnanks and will greatly appreciate it.Message Edited by White_Hair on 0-27-200605:4 PM

The onboard sound is disabled. Unfortunately I sold the Seasonic PSU to my friend. The OCZ GameXStream is suppose to be the higher grade psu than Seasonic PSU. Also, the cold boot problem only exists if the sound card is plugged to the motherboard. I tried change different pci slot. It doesn't seem to help the problem. Thanks for the reply Message Edited by White_Hair on 2-02-200606:07 AM

Boot problem with 745 ultra MB

Similar Messages

Maybe you are looking for