Boot problems with Satellite Pro M40 running Windows XP SP2

The computer suddenly shut down when I was using it. I switched it back on and all I get now is a screen which apologize for any inconvenience and telling me that Windows did not start successfully, with options to start in their different modes ie.
Safe/normal etc. I have tried them all, without success, if anyone has any ideas I would be most grateful.

Hi
> Safe/normal etc. I have tried them all, without success,
Because of your statement in the first post I assume the notebook does not boot successfully and you cannot access the Windows.
In such case I would recommend the simplest OS reinstallation from the Recovery CD.
If this procedure fails, the hardware malfunction is possible In such cases its not easy to say what could be wrong.
But we should focus on the memory and HDD
However, if you dont have own resources for troubleshooting I would recommend contacting a technician for an additional help.
Good luck

Similar Messages

  • What external modem will work with Satellite L500-1XL running Windows 7

    Hi,
    When in Spain I need to use dial up to the internet via Telefonica.
    I am assuming the L500-1XL does not have an internal modem?
    What external modem will work with the L500-1XL running Windows 7 ?
    Many thanks in advance for your help.
    A

    Hi
    Youre right Satellite L500 doesnt have an internal modem so you need an external one.
    I think you can buy every modem that is at least compatible with Vista. Alternative ask your authorized service provider or favorite computer dealer
    Friend of me has good experience with 56K modem from USRobotics like this one:
    [USRobotics 56K USB Faxmodem USR5637|http://www.amazon.co.uk/USRobotics-56K-USB-Faxmodem-USR5637/dp/B0019LZCEI/ref=sr_1_1?ie=UTF8&s=electronics&qid=1269253039&sr =8-1]

  • BIOS Update 6.70 problem with Satellite Pro C850-172

    I have two problems with updating the BIOS (the 1st is more important then the 2nd one):
    1. While trying to install BIOS Update 6.70-WIN (29/11/13) it says that:
    "The version of ROM file is the same as that of BIOS"
    and it stops. In the DOS window it shows one phrase:
    "NOT Windows 8 Platform, using Windows 7 update...".
    I use Windows 7 Home Premium 64bit system but recently there has been major automatic update done to it.
    I got lost. Is there anything I can do to update BIOS?
    2. Earlier it says that Flash process will be terminated and I need to "contact OEM BIOS engineer to add the NV storage location by HISII interface". But if I want to risk I can continue etc.
    Previously I took the risk and updating went well.
    But is there possibility to contact OEM BIOS engieneer?

    Hi
    >While trying to install BIOS Update 6.70-WIN (29/11/13) it says that:
    >"The version of ROM file is the same as that of BIOS"
    What is the present BIOS version which is available on your notebook?
    In case the BIOS is already up to date, the BIOS flash procedure will be interrupted.
    >"NOT Windows 8 Platform, using Windows 7 update...".
    Im not quite sure about the meaning of this information but it looks like the BIOS update was released for Windows 8 system and probably its required to upgrade the system from Windows 7 to Windows 8 in order to be able to flash the BIOS
    By the way: why you want to update the BIOS? Just because new version is available?
    Please note that BIOS update does not improve the notebook performance but fixes some issues. In case your notebook runs properly, the BIOS update is not very important

  • Presonus Faderport problem with Logic Pro 7 running Snow Leopard

    I've been been using Tiger to run Logic Pro 7 without any problems for the past few years. I've held out on upgrading to Snow Leopard since everything worked so nicely, but I finally gave in and loaded 10.6.6. Logic Pro 7 seems to be okay except for my Faderport control surface functionality. I upgraded to the newest FP firmware, and Logic 7 recognizes the FP, but it doesn't work. When I open a Logic project I get a pop up dialog box that says:
    Module file "Faderport" is too new and cannot be used with this version of Logic control surfaces. Please get an update of the Logic control surface application file. I also get another dialog box that says: "Loading Module Faderport..." But nothing happens.
    I'd appreciate any and all ideas on how I might deal with this. Thanks!

    Hi,
    I'm getting this message since updating the Faderport Firmware. I'm using Logic 7 in Tiger still.
    How did you fix the install pref?

  • Problem Starting Premier Pro CS3 on Windows XP SP2. Crashes just as toolbar appears. HELP!!

    Installed Premier Pro CS3 back onto my old laptop, licensed correctly etc... but will not open the program past the loading box. Quickly flashes up top menu bar and then vanishes. help please as i need it tonight!!

    reset your preferences by holding down shift-ctrl-alt while starting pr.  if done correctly you'll see a confirmatory dialog.

  • Satellite Pro M40: screen stays dark untill Windows has fully loaded

    Hello to all on here.
    I have a problem with my laptop. My laptop is a Satellite Pro M40.
    When I turn on my laptop I have found the back light will not come on... the screen will stay dark untill it has fully loaded into Windows. I have checked all of my power options and there all fine. Even if I can get to the Bios screen its impossible to read the txt due to no backlight. I have tried holding the Fn & F7.. noy joy.
    Does anyone have any ideas?
    Richard

    Hello Richard
    I didnt see something like that before and I am little bit confused why you can not see BIOS settings but running OS. Usage of FN+F7 key combination will not help because this option works just under Windows and not under DOS level.
    If possible try to connect external monitor and test it again. Anyway I dont believe that you can fix it on your own. Try please to contact Toshiba authorized service partner in your country. Explain the situation and you will see what they will say.
    If you find out something please let us know. It will be really interesting to know why this happen.

  • I have 64 bit windows 7 and CS4 Production Premium. I have a problem with Premiere Pro CS4, it keeps

    I have 64 bit windows 7 and CS4 Production Premium. I have a problem with Premiere Pro CS4, it keeps freezing and Crashing. A simple thing like leaving the project idle for about 15 minutes, you come back and find that it has frozen. Also if you drag out a clip on the timeline you will find that the whole application freezes. Any possible solutions would be much appreciated.

    Could be several factors at play here. This ARTICLE might give you some tips on getting your computer ready for an editing session. Note that there are some added tips on Win7, thanks to Black Viper, near the end.
    If nothing is helping, then the tips in this ARTICLE might help you find some clues amongst the breadcrumbs left behind with a hang, or crash.
    The link in this ARTICLE will give you some general troubleshooting tips.
    If nothing improves, then please post back with more details. This ARTICLE will give you tips on what would be helpful.
    Good luck,
    Hunt

  • HT1222 I have a new MacBook Pro and running Windows 7 on that side with Parallels.  My Windows side keeps locking up.  Help

    I have a new MacBook Pro and running Windows 7 on that side with Parallels.  My Windows side keeps locking up.  Help

    You should be able to get the CS3 programs installed and running on the new pc since CS3 is spec-ed for Windows 7 Service Pack 1.  Downloading the programs does not require a serial number.  You can find them here:  Download CS3 products  but you will need the serial number to activate the programs.  You might be able to find that thru your Adobe account online.
    You will not be able to install the CS5 Mac version on a PC and you won't be able to trade it to a PC version either due to it being an older version.  Trades are allowed only for the latest version (CS6)

  • Satellite Pro M40 hard drive failure - Recovery disc on new drive?

    Hi
    My Satellite Pro M40 hard disk has died and I want to install a new drive. Unfortunately my old drive is 60Gig and the Toshiba parts website has only 40 Gig or 80 Gig drives.
    Will I encounter any problems with the recovery disc if the hard drive is not exactly the same?
    Your advice would be appreciated.
    C

    No, there shouldnt be any problem with the Toshiba recovery CD.
    On the recovery CD you will find a Windows OS, Toshiba drivers and utilities and additional software.
    These whole applications are packed in image files.
    You should only be sure that the HDD is compatible with your notebook and will be recognized in the BIOS.
    Then just simply boot from the recovery CD and the installation should start.

  • Need advice about Satellite Pro M40

    I wonder if anyone could advise me. We have just purchased 8 Smart boards for our school With these I ordered 8 SatProM40 laptops. When I ordered them I checked the spec as follows
    Toshiba SatProM40 - Celeron M360 1.4 GHz - RAM 256MB - HD 40GB - CD-RW/DVD-ROM combo - Mdm - Lan EN - FAST EN - Win XP Pro - 15.4" TFT.
    I checked before I ordered that the RAM was 256 because I had heard that this is the mininimum recommended to run XP.
    The laptops take almost 5 minutes to turn on and everything takes an age to work it is really frustrating and they are totally unusable for our school because all the lesson is taken up with getting the computers to run anything.
    I checked the System information and found the laptops were running of 192Mb of RAM and rang the supplier. I was told that they used 64MB for the graphics card and therefore they had supplied a 256MB RAM computer.
    My question to anyone who can help is:- is this normal practice. If I knew this I would have ordered a laptop with more RAM to compensate.
    Any advice that would help us get our children working on their new computers would be gratefully received. Thank you.

    Hi Lisa
    In my opinion Satellite Pro M40 is nice unit for school work but I agree with you that 256 MB is really minimum RAM and I recommend you to buy more 256 MB or even 512 MB, depending on your budget.
    Compatible RAM modules are:
    PC2700 256MB (PA3311U-2M25)
    PC2700 512MB (PA3312U-2M51)
    Problem is that this unit use shared memory and that means that RAM will be also used for graphic. If there is someone who has good PC knowledge let them check all running processes. Many of them are useless and can be disabled. I have also noticed that preinstalled Antivir application (Norton) slow down running OS rapidly. If all units are not connected to the internet I recommend you to remove it.
    By the way: there are many good antivir applications who runs well and dont slow down the running OS.
    Good luck!

  • Satellite Pro M40 - touchpad and left click repair guidance

    Hi,
    I have a problem with the left click of my Satellite Pro M40 (PSM46E). It has lost the 'click'.
    Does anyone have some guidance for taking the top off to repair? What screws and how etc?
    Many Thanks

    Hi!
    I think you will not get some guides because only an ASP (authorized service provider) has someone. These documents are not for the public.
    I dont know how to disassemble the notebook but this procedure is tricky. You must remove a lot of screws and parts like keyboard, LCD, upper cover and so far.
    *You can try it and try but its your own risk*. I think this should do by a notebook technician.
    By the way, I founded a maybe interesting article for you:
    http://www.irisvista.com/tech/laptops/ToshibaM45/Satellite_M45_disassembly_1.htm
    Bye

  • Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    I know OSX 10.9 Mavericks introduced a power saving feature called App Nap which is meant to slow down applications that it determins are inactive (or when minimized). This would mostly likely cause problems if you're dynamically linking After Effects comps to your timeline or sometimes exporting to Media Encoder.
    Try disabling App Nap for all your Adobe App files...
    Go to your Applications folder
    Go into individual Adobe app folders (ie. Adobe Premiere Pro CC)
    Right-click on the Adobe app file (ie. Adobe Premiere Pro CC.app) and select Get Info
    When the info window opens up, add a checkmark beside "Prevent App Nap"
    Restart the application
    This fixed all my performance issues.
    -Pete

  • HI, I just bought Photoshop CS5 and I have a problem with HDR pro

    HI, I just bought Photoshop CS5 and I have a problem with HDR pro . when I am trying to mount 3 images together it act in a strange way ( the images appear and disappear many times) then when the window with the result appear and I say ok it open up in photoshop as a single image ( in the layers there is just 1 photo) and when I am trying to work it up with the Plug in/filter HDR Effex Pro (Nik softwear) a pop up window appear saying that the file is missing and the operation it is not possible. Why and what is happening ? Someone can help me ?

    This is normal operation. The output from HDR pro does not produce a layered file. You make all your adjustments in the Nik Plug-in. Once Nik has finished you then make any rinal changes in Photoshop. Trying to use NIK again on the image in Photoshop is not the way to do this.
    When HDR pro comes up do you see all the presets and controls? Presets on the left and controls on the right
    MK

  • We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    Your Acrobat is running in Trial Mode.  Try this KB: Creative Cloud applications unexpectedly revert to trial mode | CS6, CCM
    If it doesn't work you need to contact Adobe Support for assistance.

  • Poll: Do you have cold boot problem with SB X-FI Fatal1t

    Hi guys:
    I have post a thread regarding the cold boot problem with SB X-FI Fatalty and OCZ GameXStream 600W SLI power supply combination. Apparently, no one has answer to that . In addition, I have recently RMA'd my psu and received a brand-new unit. The same problem still exists. If the problem is really with the power supply, doesn't matter what kind of the setup I have, I should still have the cold-boot problem. However, it doesn't seem like that. Doesn't matter what kind of cards I put on the motherboard, as long as the SB X-FI Fatalty card is there, there is cold boot problem (even with the setup of cpu, mother, ram, and the sound card only, WITHOUT video card and harddri've). And for other different setup without the SB X-FI Fatalty card, there is no cold boot. The cpu and memory are running at stock speed.
    My post regarding the cold boot issue:
    http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=79753
    There is one user on the forum saying he has the same problem. Therefore, I think it might be the imcompatibility between the X-FI Fatalty and OCZ GameXStream PSU.
    I would like to know how many people that has the same problem that I am having. So I can possibly narrow down the problem and contact OCZ tech support or creative tech support with more information. It would also be benefitical to those who have the same problem as I do.
    Please post your system setup as well in the thread.
    Greatly appreciate your opinions. Message Edited by White_Hair on 2-02-200604:58 AM
    Message Edited by White_Hair on 2-02-200603:22 PM

    I would venture to say that it isn't your powersupply, but more likely the X-Fi. I had troubles with my system, until I pulled out my X-Fi and replaced it with a non Creative Labs sound card. One of my troubles, which I incorrectly blamed on my powersupply was the ASUS A8R-MVP motherboard I had and the X-Fi XtremeMusic card, was after gaming for 4 hours, was the?sudden reboot of my system. Powersupply before, was an Antec TrueControl 2 550watt PSU. As it stands right now, I no longer have the parts mentioned and have a decent 700watt powersupply in my system, along with an ABIT AT8 32X motherboard. As you have probably seen there are a lot of problems with the X-Fi soundcards, and I in my right mind can't blame the motherboard, powersupply, motherboard chipset, ram, or any other component in ones system, if one is having trouble other than the X-Fi itself. I'll be honest, there is something quite frankly wrong with the X-Fi, and exactly what that is, I'll probably never know like most people.

Maybe you are looking for