Boot strap drivers installation failure

Hello!
Got my Mac Book Pro last night, updated the OS and firmware, and finally got XP installed. But now when I run the Macintosh Drivers for Windows XP setup, it extracts everything, says "Preparing to install", then I got the message "This software does not support your hardware". Great. I had the RAM upgraded to 2 gigs and also upgraded to the 7200 RPM drive, but now I am starting to regret it.
Has this happened to anyone else? Is there some place where Apple posts these drivers separately?
Any help greatly appreciated!

Thank you for replying. It was my fault for sure... I tried installing Media Center (two disks), realizing my mistake half way through the install. When it asked for disk 2, I hit ESC and it continued without a hitch. XP started and seemed to work, but I think there were some files missing that made it so the MSI wouldn't fully install.
Bought a single disk copy of XP (with SP2) and redid everything, and the drivers are now installed and I am a happier Mac owner running XP.
Thanks again for the reply!

Similar Messages

W8.1 installation failure in creation of computer's boot configuration

Hello,
I have an official version of windows 8.1 64 bit, which I recorded on a disc through boot camp assistant mac, also making the disk partition.
after the wizard restart the mac and start installing windows.
makes copying and installation steps and then fails, appearing the following error message: "Windows Could not update the computer's boot configuration. Unable to continue with the installation."
I do not understand where the fault is!
Already deleted the partition and went to do it again, tried another disc too.
I did install windows 8.1 on a equal macbook like two days ago and worked well.
I have a macbook pro retina 15 "with the Mavericks (late 2013), dedicated graphics.

Hi all,
I ran into a similar issue trying to install windows 8.1 on the latest 13 MacBook pro (the forcetouch trackpad one) and i also got caught in a loop of errors between EFI being formatted incorrectly as ntfs instead of fat32 as well as an error that said I had an MBR table.
I Succeeded eventually by following this tutorial which installs windows from the MacBook pro's native EFI and requires diskpart commands;
http://thetecherra.com/2012/12/11/tutorial-install-windows-8-on-a-mac-via-native -efi/
I Actually followed the steps starting from the steps where you install windows so I didnt even wipe my os x clean!(I was lucky or something).
additionally, I left unallocated space for windows before beginning and I used gdisk to create/fix my disc's protective MBR before i followed the tutorial above from the instructions to install windows.. windows booted and installed on my macbook without a problem and I did not have the black screen problem so I didn't need to follow the remainder of his tutorial to fix the black screen. I found gdisk / creating the protective MBR tip from this forum;
http://superuser.com/questions/508026/windows-detects-gpt-disk-as-mbr-in-efi-boo t/508454#508454
i installed the boot camp drivers from the USB bootcamp had made when I tried and failed to use boot camp assistant.
Everything works elegantly down to the Intel iris graphics on multiple screens and I do agree that windows looks great with a retina display. almost better than os x if windows wasnt as simple to navigate as OS X.
cheers, I hope this saves someone a few headaches as I spent several evenings trying to get windows installed. a tip I would offer before attempting is to definitely backup your drive,(I lucked out) and to calculate your windows partition size accurately in MB beforehand so that you use your entire disk and give diskpart the appropriate size so you don't end up with free space your windows partition could have enjoyed.

2010 Mac Pro Boot Camp - Refuses to boot Windows after installing Boot Camp drivers

Hey all,
I have a quad 3.2Ghz 2010 Mac Pro with a Radeon 5870 and 8 GB RAM.
I have 2 10000RPM WD Raptor drives, the first drive is my Lion boot drive. The 4th bay contains the second Raptor which has Windows 7 Ultimate 64 bit installed. Bay 2 has Time Machine, bay 3 has a Windows backup drive.
I had first installed Windows and the Boot Camp drivers a few months ago and everything was humming along smoothly. Monday I tried to boot into Windows and it crashed immediately after the black Booting Windows screen started to change to the login window. This happened repeatedly. Nothing changed on the system that I am aware of. Whenever I tried to boot windows again, it booted into the repair mode. That did not seem to work because after running the repair it would still not boot.
So I did what is usually required of Windows, and that was to reinstall. I reformatted the hard drive, ran Boot Camp assistant, and started the install.
Everything was peachy so far, so I tried to reinstall the Boot Camp drivers (4.0). Did a reboot. Same problem. Doh!
So I did ANOTHER reinstall, and everything was fine. But this time I tried to install the Boot Camp drivers off the os install disc that came with my Mac (3.1). Still no go!
So finally I did my third reinstall and after that I did not install Boot Camp drivers. However, I did load up the CD and individually installed drivers for the Apple Mouse, Apple Keyboard, Cinema Display, etc. No problems whatsoever. Everything is actually still humming along fine.
So it looks like running the full Boot Camp install for some reason no longer works. Which means I am missing the Apple Boot Camp control panel, but that's not really a big deal. Althought it's quite annoying to not have the functionality of the special Mac keyboard keys like volume control, etc.
Has anyone run into this? I thought it might be a hardware problem but my Mac OS X OS exhibits no problems whatsoever.
Thanks!

Thank you to The hatter.
I have a Mac Pro mid 2010 with a SSD and several internal hard disks. For some time I was trying to install Windows 7 on a fresh boot camp volume on a new WD 7200rpm 1TB hard disk. It was taking hours to install, and then I had a series of failures to reboot that proved permanent. The Window Repair utility would come up and took forever to repair the volume - but failed to actually do so, requiring completion reinstallation of the bootcamp volume. This occurred three times, between 1 day and 2 months after installation. I had already moved the Windows drive in to drive slot 1 of the Mac Pro.
Eventually I gave up and installed boot camp on a secondary partition of the SSD. This worked fine, however is limited in capacity. So yesterday I thought I would try to install Windows on the hard disk again. The Windows installer took many hours to do its thing, and eventually a message came up that the installation had failed.
I took your tip about possible hard disk failure, and ran Techtool Pro surface scan. It turns out that there are lots of bad blocks being reported. According to Micromat's documentation, the bad blocks being reported are those that may be in critical areas of the disk that cannot be mapped out. They recommend low level reinitialisation (with zeros) to map out the bad blocks, if possible. I am now running Apple's Disk Utility to do this, and fingers crossed that this reinitialisation succeeds, or I will have to replace the drive.

Failed to Install The New Preview Build. Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.

Hello,
I'm having issues upgrading my Windows 10 Technical Preview installation build 9879 to a newer build that's become available late January 23rd.
I am installing the new upgrade in a Hyper-V virtual machine and get the following error:
Failed to install the new preview build, please try again later. 0x80246007
What could be the problem?
Previously I've had messages that Windows cannot be upgraded on a computer with less than 2 Gbyte of RAM. That's a Hyper-V VM with dynamic memory and I was highly surprised to see this error; never had this before. Had to set 2048 Mbytes as a minimum memory
for this VM. Now that I have this 80246007 error code.
When looking up System log, the following error messages are listed multiple times:
Installation Failure: Windows failed to install the following update with error 0x80246007: FBL_AWESOME1501 9926 Professional.
The errors are returned for the Event ID 20 by WindowsUpdateClient
in task category Windows Update Agent..
I reviewed the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability
registry key as suggested in Windows
Insider stuck on build 9841 - "No new preview build was found", and here is what it shows:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsSelfHost\Applicability]
"BranchName"="fbl_awesome1501"
"ThresholdRiskLevel"="low"
"ThresholdOptedin"=dword:00000001
Note, when attempting to install the downloaded update from a native boot, installation starts with no errors.
However, since setup is not supported for a natively booted VHD files, it does not proceed further showing a message that installation on virtual drives is not supported.
Looks like Setup is having problems installing in a Hyper-V virtual machine.
Possibly, some ESD files got corrupted during downloading? Is it possible to remove them and re-download missing files? (I, however, noticed that Windows seems to re-download upgrade files after you restart 9879 and attempt to check for a new build.
Any clue why installing under VM causes 9926 to fail?
Thank you in advance.
Well this is the world we live in And these are the hands we're given...

Hi,
According to the error message, this problem seems like update package installation failed during system upgrade.
You can try to remove ESD file which locate at boot of C drive and upgrade the system again for test.
On the other hand, make sure the system 9879 installed all Windows pushed updates before system upgrade.
Roger Lu
TechNet Community Support

Windows 8 crashes and with the error "kernel_security_check_failure" after installing Boot Camp drivers.

Hi!
I've got a new 27" iMac (late 2013), and I was going to install Windows 8.1 (64-bit) to be able to play a few games.
Everything went smoothly (installed normally via Boot Camp Assistant), and after the Windows setup, the Boot Camp drivers needed to be installed. After this, the computer rebooted, but crashed at a blue screen with the error called "kernel_security_check_failure".
It rebooted a few times on its own, but after a few times, I got some options, and I chose to "refresh" the Windows 8 install, meaning it would reset the install while keeping my files (even though I didn't have any, as I never got to use it). This took some time, but it worked, and it booted into W8.
The Boot Camp drivers had been removed though, so I had to reinstall them. After they had reinstalled, the computer rebooted and the same blue screen with the same error hit me.
Something tells me that some of the BC drivers are messing things up. I can't find any information on this elsewhere.
Would it be possible to install only selected drivers, to eventually find out which driver is causing the problem?
All help is greatly appreciated!

I finally gave up, reloaded everything, this time, using WIn 8.1 Pro, not Enterprise. After I did the updates, patches, Norton 360, shut computer down and connected the external drives, and booted up...and got the BSOD. This time, I went to Microsoft and downloaded the Windows Debugger, and think I may have found the problem...NORTON!
Probably caused by : SYMDS64.SYS ( SYMDS64+71be6 )
Am conrtacting them, but, here's the Debugger output:
Microsoft (R) Windows Debugger Version 6.3.9600.17029 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Dump\MEMORY.DMP]
Kernel Bitmap Dump File: Only kernel address space is available
************* Symbol Path validation summary **************
Response                         Time (ms)     Location
Deferred                                       SRV*C:\Symbols*http://msdl.microsoft.com/download/symbols
Symbol search path is: SRV*C:\Symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 8 Kernel Version 9600 MP (8 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 9600.17085.amd64fre.winblue_gdr.140330-1035
Machine Name:
Kernel base = 0xfffff802`0f87e000 PsLoadedModuleList = 0xfffff802`0fb482d0
Debug session time: Tue Jun 17 00:48:52.131 2014 (UTC - 6:00)
System Uptime: 0 days 0:03:09.864
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
*                        Bugcheck Analysis                                    *
Use !analyze -v to get detailed debugging information.
BugCheck 139, {3, ffffd0002852d3e0, ffffd0002852d338, 0}
*** ERROR: Module load completed but symbols could not be loaded for SYMDS64.SYS
*** ERROR: Module load completed but symbols could not be loaded for SYMEFA64.SYS
Probably caused by : SYMDS64.SYS ( SYMDS64+71be6 )
Followup: MachineOwner
6: kd> !analyze -v
*                        Bugcheck Analysis                                    *
KERNEL_SECURITY_CHECK_FAILURE (139)
A kernel component has corrupted a critical data structure. The corruption
could potentially allow a malicious user to gain control of this machine.
Arguments:
Arg1: 0000000000000003, A LIST_ENTRY has been corrupted (i.e. double remove).
Arg2: ffffd0002852d3e0, Address of the trap frame for the exception that caused the bugcheck
Arg3: ffffd0002852d338, Address of the exception record for the exception that caused the bugcheck
Arg4: 0000000000000000, Reserved
Debugging Details:
TRAP_FRAME: ffffd0002852d3e0 -- (.trap 0xffffd0002852d3e0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=ffffe00059c129f0 rbx=0000000000000000 rcx=0000000000000003
rdx=ffffe0005718d2a0 rsi=0000000000000000 rdi=0000000000000000
rip=fffff8020f9e8cdb rsp=ffffd0002852d570 rbp=0000000000000000
r8=0000000000005aa0 r9=00000000000007ff r10=ffffd00066cc8000
r11=ffffe00059963040 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei pl nz na pe cy
nt! ?? ::FNODOBFM::`string'+0x682b:
fffff802`0f9e8cdb cd29            int     29h
Resetting default scope
EXCEPTION_RECORD: ffffd0002852d338 -- (.exr 0xffffd0002852d338)
ExceptionAddress: fffff8020f9e8cdb (nt! ?? ::FNODOBFM::`string'+0x000000000000682b)
   ExceptionCode: c0000409 (Security check failure or stack buffer overrun)
ExceptionFlags: 00000001
NumberParameters: 1
   Parameter[0]: 0000000000000003
DEFAULT_BUCKET_ID: LIST_ENTRY_CORRUPT
BUGCHECK_STR: 0x139
PROCESS_NAME: System
CURRENT_IRQL: 2
ERROR_CODE: (NTSTATUS) 0xc0000409 - The system detected an overrun of a stack-based buffer in this application. This overrun could potentially allow a malicious user to gain control of this application.
EXCEPTION_CODE: (NTSTATUS) 0xc0000409 - The system detected an overrun of a stack-based buffer in this application. This overrun could potentially allow a malicious user to gain control of this application.
EXCEPTION_PARAMETER1: 0000000000000003
ANALYSIS_VERSION: 6.3.9600.17029 (debuggers(dbg).140219-1702) amd64fre
LAST_CONTROL_TRANSFER: from fffff8020f9ddae9 to fffff8020f9d1fa0
STACK_TEXT:
ffffd000`2852d0b8 fffff802`0f9ddae9 : 00000000`00000139 00000000`00000003 ffffd000`2852d3e0 ffffd000`2852d338 : nt!KeBugCheckEx
ffffd000`2852d0c0 fffff802`0f9dde10 : ffffe000`59c8cc40 00000000`00000000 ffffe000`54b71040 fffff800`1d6d40b6 : nt!KiBugCheckDispatch+0x69
ffffd000`2852d200 fffff802`0f9dd034 : 00000000`00000000 00000000`00000000 ffff6d2d`50094127 fffff802`0f81458f : nt!KiFastFailDispatch+0xd0
ffffd000`2852d3e0 fffff802`0f9e8cdb : ffffc000`061df4e0 ffffc000`061df4e0 ffffc000`061dfbf8 00000000`00000000 : nt!KiRaiseSecurityCheckFailure+0xf4
ffffd000`2852d570 fffff800`1d7a0be6 : ffffe000`59e10120 fffff800`1d794388 ffffe000`54dfe9c8 fffff800`1d735f7c : nt! ?? ::FNODOBFM::`string'+0x682b
ffffd000`2852d5a0 fffff800`1d7a54e2 : ffffc000`061df4e0 ffffc000`061dfbf8 ffffc000`061df550 fffff800`1d7367ea : SYMDS64+0x71be6
ffffd000`2852d5d0 fffff800`1d737f20 : ffffc000`061df378 ffffc000`061dfbf8 00000000`00000000 ffffc000`05a9bf18 : SYMDS64+0x764e2
ffffd000`2852d620 fffff800`1d73e171 : ffffc000`051e6a88 ffffc000`05a9bf18 ffffc000`05a9bf18 ffffe000`5988cb00 : SYMDS64+0x8f20
ffffd000`2852d650 fffff800`1d782027 : ffffc000`061ea018 00000000`00000000 ffffe000`58409008 fffff800`1d794388 : SYMDS64+0xf171
ffffd000`2852d680 fffff800`1d79af21 : ffffc000`061ea018 ffffd000`2852d8c9 ffffe000`58409008 00000000`10000004 : SYMDS64+0x53027
ffffd000`2852d6c0 fffff800`1d9a3bb3 : ffffe000`58409078 fffff800`1d98b3e8 ffffe000`58409008 ffffd000`2852d8c9 : SYMDS64+0x6bf21
ffffd000`2852d6f0 fffff800`1d9a91fa : ffffe000`5840a1a8 ffffe000`58409008 00000000`00000000 ffffe000`00000000 : SYMEFA64+0xe9bb3
ffffd000`2852d720 fffff800`1d9ae015 : 00000000`00000000 00000000`00000000 ffffd000`2852d8c9 ffffe000`58a10e60 : SYMEFA64+0xef1fa
ffffd000`2852d760 fffff800`1d9adf4c : 00000000`01820201 ffffe000`58a10e60 ffffe000`58a10e60 ffffe000`58a10be0 : SYMEFA64+0xf4015
ffffd000`2852d790 fffff800`1d9b294c : ffffe000`59e0a150 ffffe000`58a10e60 ffffe000`5988ca80 ffffe000`58a10e60 : SYMEFA64+0xf3f4c
ffffd000`2852d7c0 fffff800`1d9a2435 : ffffd000`2852d8a0 ffffe000`599a4010 ffffd000`00000000 ffffe000`59e0a010 : SYMEFA64+0xf894c
ffffd000`2852d7f0 fffff800`1d6d528a : 00000000`00000000 ffffe000`59e0a070 ffffe000`5604e300 ffffe000`58a10e60 : SYMEFA64+0xe8435
ffffd000`2852d820 fffff800`1d71bf76 : ffffd000`2852d960 00000000`00000000 ffffe000`5604f900 ffffe000`571dab10 : fltmgr!FltpPerformPreCallbacks+0x31a
ffffd000`2852d930 fffff800`1d6d413a : ffffe000`57170dd0 ffffe000`571dabd0 ffffe000`59cf18c0 fffff802`0fd411a7 : fltmgr!FltpProcessShutdownRequest+0x122
ffffd000`2852d9b0 fffff802`0fbf7518 : ffffe000`57170dd0 00000000`00000001 ffffe000`571dabd0 fffff802`0fb54a90 : fltmgr!FltpDispatch+0x13a
ffffd000`2852da10 fffff802`0fbf7273 : 00000000`00000001 00000000`00000000 00000000`00000001 00000000`00000000 : nt!IopShutdownBaseFileSystems+0xb8
ffffd000`2852da90 fffff802`0fbfb722 : fffff802`0fbfb4b0 00000000`00000000 ffffe000`59963040 ffffe000`59963040 : nt!IoShutdownSystem+0x127
ffffd000`2852db10 fffff802`0f8d1adb : fffff802`0fbfb4b0 ffffd000`2852dbd0 00000000`00000000 ffffe000`59963040 : nt!PopGracefulShutdown+0x272
ffffd000`2852db50 fffff802`0f94d794 : ffffe000`59965800 ffffe000`59963040 ffffe000`59963040 ffffe000`54b71040 : nt!ExpWorkerThread+0x293
ffffd000`2852dc00 fffff802`0f9d85c6 : ffffd000`66c40180 ffffe000`59963040 ffffe000`59965800 00000000`00000000 : nt!PspSystemThreadStartup+0x58
ffffd000`2852dc60 00000000`00000000 : ffffd000`2852e000 ffffd000`28528000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
STACK_COMMAND: kb
FOLLOWUP_IP:
SYMDS64+71be6
fffff800`1d7a0be6 33d2            xor     edx,edx
SYMBOL_STACK_INDEX: 5
SYMBOL_NAME: SYMDS64+71be6
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: SYMDS64
IMAGE_NAME: SYMDS64.SYS
DEBUG_FLR_IMAGE_TIMESTAMP: 51f84c44
FAILURE_BUCKET_ID: 0x139_3_SYMDS64+71be6
BUCKET_ID: 0x139_3_SYMDS64+71be6
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0x139_3_symds64+71be6
FAILURE_ID_HASH: {bf9be68b-5f04-08d4-3152-3d420dc362f6}
Followup: MachineOwner

Can install Windows 7 Pro, but not Boot Camp drivers

I have used Boot Camp assistant to install Windows 7 Pro (64 bit), and built the USB drive with Boot Camp drivers.
Installed on a separate drive on my Mac Pro.
When I install the drivers and reboot, I get an error. Basically Windows says there is an error and it needs to run System Restore in order to roll back to the previous status (ie. remove Boot Camp drivers).
I am using the latest Boot Camp drivers for a Mac Pro (4,1) and 64 bit Windows.
I tried downloading the drivers from Apple's website in Windows, unzipped and installed - same issue.
Windows is not yet registered.... (might that be an issue?)
Grateful for some ideas. I have previously had Win7 running on this machine, and even Win 8 (which crashed - necessitating a roll back to Win 7 whcih is nicer).
TIA

the drivers have a root setup.exe if people have problems with that they can manually navigate to the sub dirs and run the driver installs for the various hardware manually
the various driver exe install will only install if they detect the hardware is there so it's safe to run installers for say a video card ones computer does not have
and if one of the driver don't work of the hardware related to it is defect in some way you can identify which one as the restore would happen right over that driver install
that windows is not registered should not play apart as far as I know

I have an older Mac Pro (2006). I want to install Boot Camp and Windows. I have installrg a purchased Snow Leapord on the machine. To install Windows, am I limited to Windows 7? And where are the Windows 7/Boot Camp Drivers? On the OS disk? Download? Tha

I have an older Mac Pro (2006). I want to install Boot Camp and Windows. I have installed a boxed Snow Leapord on the machine. And it says the download of the Boot camp drivers cannot continue because they are not available. But at that point I have not inserted a windows disk, so how does it know i have XP?
So it appears I am limited to Windows 7? And where are the Windows 7/Boot Camp Drivers? On the OS disk?
Finally, since I have necer considered Windows 7 before, I assume there are no compatability issues with mainstream applications that were running in XP?
Thank you.

You're welcome
Just remember to reformat the partition (bootcamp partition) to NTFS with the windows installer, ensure to pick the correct partition.

Can't install Boot Camp Drivers on Win 7 (Fusion)

I'm really sorry - I know this has been asked a thousand times before, but every response I've found so far either didn't work for me or it was too technical for my limited knowledge. I'm on the verge of tears after having tried to solve the problem for over 5 hours. It's past 2am here in Australia and I really should go to sleep but this is driving me insane!
Yesterday I installed Windows 7 on my Macbook Air (13" 2011 model, running Mountain Lion) using Fusion 5. I need to run Windows-only applications for work, which also requires accents (I am a translator).
As I didn't go about it using Boot Camp, I tried following this step-by-step to get my keyboard working properly: http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&d ocTypeID=DT_KB_1_1&externalId=1005578
No luck.
I downloaded the drivers using Boot Camp onto a USB stick formated as MS-DOS (FAT). I tried running setup.exe but keep getting the horrible "This version of Boot Camp is not intended for this computer model" no matter what (tried the "Troubleshoot compatibility" trick, tried re-formatting my stick and downloading the drivers again... nothing worked).
I then tried to run AppleKeyboardInstaller64.exe only and got an installation wizard. Windows says installation is complete, although I can't see this driver on the program list (should I?) - I can only it see it when I go to Control Panel\Programs\Programs and Features (from there I get the option to uninstall it but not to open it). HOWEVER, when I attempt to add an Apple keyboard, I can't see any, under any language.
I have tried alternative solutions like building my own keyboard layout but that didn't work either because I can't make the accent functions work in order to set up the layout!
Adding a foreign keyboard layout to Windows just gave me a very random set of strokes that will drive me insane if I have to type them regularly.
I just want to be able to use the standard strokes for accents on both OS:
Alt+e for á
Alt+i for ^
Alt+c for ç
Alt+` for à
Alt+n for ~
Can any good soul help me? I'm not an IT person, just someone who used to be married to her Mac (a very happy marriage) and who is now about to throw the laptop out of a window. Please HELP!!!

That article was also my starting point and I have followed those steps again and again and again. I haven't slept, I haven't done anything other then try to make it work for more hours than I can count. I came here for help because that solution is not working for me.
The region and keyboard type settings simply don't have the Apple keyboard layout listed. As I said, someone on the Fusion forum tried to follow the article's instructions too and he managed to get it working because he COULD run setup.exe (Boot Camp Drivers) on his machine, and I CAN'T. Yes, it is all explained in that article... but the drivers WON'T INSTALL, I get an error message saying "This version of Boot Camp is not intended for this computer model".
First you said it wasn't physically possible for me to install the drivers, then you said I should just follow the article. Well, the article clearly says "Install the Boot Camp Windows device drivers in the virtual machine" which you just said couldn't be done! I want to cry. I should have just bought a second laptop, this is too painful.

Can't install Boot Camp drivers on Early 2010 MBP

Hello there, so I'm having a problem installing drivers as you can see from the title. I was trying to create a Boot Camp partition on my girlfriend's MBP. She has the 2010 early one. Now we got windows installed on there with no problem; however, we can't seem to get the drivers that allow her speakers, webcam, etc. to work.
Initially we tried using my Snow Leoperd OSX disc because as far as I know she has snow leoperd too and she can't find her original OSX disc. I have an early 2011 MBP so when I tried using the boot camp drivers on my OSX disc it would not work. It said the drivers on mine weren't made for hers. Whatever no biggies, so I google an alternative and tried to download the drivers from boot camp manager back on her Mac Partition. It said that the drivers could not be found or could not be downloaded. Something to that effect. So now that we can't download the drivers, or use the original disc, what other options do we have?

Hello Arroyo1291,
Welcome to Apple Support Communities! Given your situation I strongly recommend you to call Apple Care support at 1-800-275-2273. When you get in touch with an AppleCare representative, ask them for a replacement Mac OS X install DVD (I think Apple calls them Fullfillment Disks). Give the representative your girlfriend's MacBook Pro serial number and tell them that the Mac OS X installation DVD that came with her computer is now missing and that you want a replacement DVD. Also, make sure to ask them if the replacement Mac OS X install DVD contains the Windows Bootcamp Drivers on it like the original Mac OS X Install DVD that shipped with your girlfriend's MacBook Pro.
One last thing, if your girlfriend's MacBook Pro is not under the AppleCare extended warranty, they may charge you a nominal fee on the replacement disc order.
Best of luck!

Windows 7 Freezes at Restart After Installing Boot Camp Drivers

Hi,
I have a MacBook Pro and am having troubles installing 32-Bit Windows 7. All seems to be functional until I install the Boot Camp drivers included on the Install Disk. I have tried using the Boot Camp 3.1 update, but the same problem occurs. After the computer freezes on the install page, I can no longer access Windows (even in Safe Mode) and am forced to restart the entire process (that is, repartition the hard drive and reinstall Windows).
If I don't install the Boot Camp drivers, Windows seems to be functional, so I'm pretty sure it's something in the Boot Camp package causing the trouble.
Is anyone else having this problem? Any ideas or workarounds?

I finally got it to work. You need to go to the NVidia website and install their drivers. I think the Apple supplied ones are out of date and are causing Windows to hang. Install Boot Camp from the supplied DVD, install the update that Apple supplies through the newly installed Boot Camp, and then go to the NVidia website to manually download the drivers. I used the GeForce 300M series installer. Make sure you do all of this before letting Windows restart.
I had a few issues with it hanging a few times, but once I was able to get into Windows it seems to be working. All of the other Apple supplied drivers seem to work.

MBP 15" 10.6 does not boot up from Installation disc, why??????

Good day,
my question is simple, so please let the answer be simple:
I have done partition on my MBP today, in order to give me more redundancy in case of a Hard drive failure. I witnessed one yesterday on a brand spanking Imac--> not pretty--> the white screen of death!! I thought I´d better cover myself and I split my HD in two--> no probs.
Anyways, I decided to try to boot from my original installation disc--> 10.5.7, Leopard.
I booted while pressing "C", or holding "Option"……and always ended up with the same thing:
It just takes me to a language selection screen, I selected my language, and then it takes me to the software installation--> but I don´t want that--> I just want to reboot from my disc--> as a general test. (Just in case of that dreaded white screen, one day!!)
So, I went to to "Stop installation" in the menu above, and I chose "Reboot" and then I chose my installation disc--> and again and again, it just takes me back to the language screen etc etc etc!!
It´s like a Merry go Round………….
What am I missing??
My Snow Leopard installation disc does exactly the same, by the way…………..
Cheers,
MXP 150 Patriot

"perhaps I didn´t explain myself properly:
I would like to boot up from my installation disc, in other words, being able to log in and see my Desktop etc.
All I get from my disc is an installation menu (after the language selection) and if I try to boot up from there (to my desktop / background etc) by selecting "stop installation--> start up disc".........it goes back to the language selection and the software installation........just where I was 3 minutes ago!
What am I doing wrong?
My friend booted up the other day from his FireWire external hard drive and he got everything, SO quick! His personal desktop, everything!
Hopefully you can tell me what I´m missing........."
You're missing the point. When you boot from your installation disk it's to install the OS and/or repair the disk and check the hardware, etc.. Your friend has a bootable external drive. he used the OS Installation disk to create that.

Installed XP; Boot Camp drivers won't work.

Everything has run relatively smoothly up until i have to install the mac drivers on XP.
I installed them successfully using a leopard disk, and then the computer restarts.
Briefly before shutting down, a blue screen shows up for about one second with a bunch of data; something about an information dump (doesn't seem too out of the ordinary, but I'm mentioning it just in case).
Then the computer restarts into windows, and says it has to perform a disk check or something... it says "Press any key to skip," yet at this point not a single key on my keyboard works, so i can't skip this step.
Then it goes through a bunch of diagnostics; windows boots up and i get an error report that says software is trying to access potentially personal information, such as wi-fi rights, and other things boot camp is supposed to take control of in order to make them function.
The next step in the installation, "After your computer restarts, follow the instructions in the Found New Hardware Wizard to update your software drivers (windows XP only)," never shows up
I presume windows thinks that the boot camp drivers are a virus, and thus won't let me install them.
I do not, however, know how to fix this.
Can anyone help ??????

I had problems with the ethernet and sound drivers following the most recent bootcamp update, which installed to deal with the trackpad issues that I was having. A pretty big mess, and the guy at the Geniius bar was very nice about saying he couldn't help.
I have discovered a repeatable problem with the update. If I completely uninstall bootcamp, and reinstall from the CD before restart, the sound an ethernet work again. I would be afraid that nothing would work (like the CD rom) if I restarted in windows sans drivers. Repairing/updating from the most current update (2.1.1 (?)) available kills both sound and wired ethernet. Repeat the procedure, and everything is fine again.
Interestingly enough, the trackpad issues seem to not have reappeared.
Opinion: the 2.1.1 bootcamp update is a downdate for my new macbook, and if I have any more issues like this that kill several days, apple is going to get it back. "It just works" clearly doesn't apply to mac running windows, and for those of us who have no choice, for whatever reason, that may continue to mean no apple.
For what it's worth, one of the guys at the genius bar said a lot of his hardware didn't work in windows either. I predict an update in the future. I hope all of this gets resolved, because there's a lot to like about the mac, but the whole non-support of windows thing is a bummer and could be a showstopper for a lot of people, despite the fact that bc is advertised as a reason to switch.

Boot Camp drivers won't install correctly.

Greetings. Recently I formatted the XP partition on my Mac, in order to do a clean installation of windows. I did everything as explained in the guide, using the Boot Camp assistant and so forth. After the installation completed, I inserted my Leopard DVD and installed the appropriate drivers. Although the message declared that everything went smoothly, the only thing I could find that was installed correctly were only the audio drivers - no video drivers, no ethernet, wireless, nothing else. I repeated the whole process (including reinstalling XP) with the same results. Any suggestions?

You will need to reinstall Windows and use the boot camp drivers that came with your machine. Do not use previous boot camp drivers or the boot camp drivers on the Leopard disk. I made the same mistake with my MacBook Pro, I installed boot camp drivers first from a CD copy, them from Leopard and had the same issues as yourself. Then I installed boot camp from the MacBook Pro DVD that came with the MBP and most of it installed. However, not all was working properly. I wiped the boot camp p[artition and reinstalled XP and used the boot camp drivers that came with the MBP and everything worked smoothly. I think the boot camp drivers are specific to a machine, at least in the case of this MBP.

Unable to install Boot Camp Drivers for Windows

Mac Pro (2) 3.2 Xeon quads
Mac OS 10.5.2
Boot Camp side - Windows XP pro x64 w/SP2
Step 3 listed in the instructions for setting up Boot Camp is to Install the Boot Camp drivers for Windows. At this point Windows recognizes my Mac Install disk 1. I get the following message: "the installer encountered errors before Boot Camp could be configured. To retry these operations at a later time, please run the installer again." I am not sure if I needed to do something to install the Service Pack 2? My firmware is at MP31.006C.B02 and 1.25f4. When I checked for the latest firmware, it returned a message that it was not necessary.
Maybe the XP pro x64 is not compatible?
Barry in St. Louis

I did install windows xp sp2 32 bit on my macbook pro 2.2 GB and I'm getting the same ...
When trying to install boot camp drivers, a message came up saying:
Boot Camp requires that your computer is running Windows XP Service Pack 2 or Windows Vista.
The only option it gave me was to click the "OK" button. When I clicked OK , another message came up saying:
Boot Camp Installer completed. The install encountered errors before Boot Camp could be configured. To retry these operations at a later time, please run the installer again. Click "finish" to exit installer. I am running a brand new full retail version of windows xp service pack 2. Applecare will not help blaming Microsoft and of course Microsoft is blaming Apple. What a bunch of useless crap!! Can anyone help??

Sound in xp using latest boot camp drivers

Hey all - I have a problem in xp that I am wondering if anyone else has...
I cannot get sound out of the "line out" (I have the computer hooked up to speakers). I can only get sound out of the headphone jack - and NEVER get the sound out of the front (internal) speaker in xp. Anyone know what's going on?
I have looked at the RealTek controls, and I can't seem to select or otherwise enable the "line out" or internal speaker. I'm lost - anyone have any help for me? Thanks!

I found something that may be helpfull... I email this guy who is an expert on drivers for boot camp- this is the discussion so far...
On Sep 6, 2007, at 22:42 , Brandon Coppin wrote:
Hey Makel,
After hours of searching I finally found a useful website... yours.
I recently purchased a new 24" imac with 2.8ghz extreme, 4gigs of ram
and the ati radeon 2600 with 256mb memory. I installed windows xp and
the so-called Macintosh drivers cd... the sound is echoing really bad
and very patchy. The video card appears to be operating normally most
of the time- until I try to play a video in media
player- it only shows shades of blue... Also Simcity 4 runs far more
slowly than it should on a system of this caliber. Do you have any
suggestions for drivers or any other insights. I really appreciate
your input,
Brandon Coppin
Hi Brandon,
I'm glad you found my article on Boot Camp drivers useful. Keep in mind I only have experience with MacBook Pros and Boot Camp, but I think I have a few pointers for you which can get you back up and running. Regarding your system spec, remember that unless you're running Windows 64bit (Vista or XP) you will not get the full benefit of those 4 gigs of ram - the most you'll see is a bit over 3 gigs. If you are running a 64bit version of Windows, stop, wipe it clean and start over with a 32bit version.
Your assumption that the iMac running XP should be a 'screamer' is correct. If SimCity 4 isn't isn't blazing fast, there's something iffy going on. First thing you should do is grab the latest driver release for your Radeon 2600. You can download those here: http:// ati.amd.com/support/drivers/xp/radeonx-xp.html
Regarding your other driver issues, I would suggest skipping the Boot Camp installer and do the driver installation manually. You'll need to know what's actually inside your system, and to do this you'll need a utility to analyze the hardware. I recommend SiSoft Sandra (http://www.sisoftware.co.uk/index.html?
dir=&location=pinformation&langx=en&a), there's a free version available for download.
Once you know what's inside your new iMac (because to be honest, I
don't) you can selectively install the drivers that Apple provides you with via the Boot Camp Assistant.
Before doing this though, nuke the Windows install you currently have and start fresh.
I hope that clears up your problems, let me know if it does, or if there's any other snags you come across.
Cheers,
Niels Mäkel
[email protected]

Boot strap drivers installation failure

Similar Messages

Maybe you are looking for