Bootcamp 2nd monitor

Hello
Im planning on using my samsung tv as a 2nd monitor.
I know it will work with max OSX but will it also work when im in bootcamp using windows
If anyone has experience with this please let me know
Chielsen

Strange. I naturally assumed that it would be the HDMI socket that has this issue.
Did a little digging and found this by Mr Grand Bennett. It was here: https://discussions.apple.com/thread/2746930?start=0&tstart=0
A related topic, but the same fundamental issues is being discussed nearby:
Can I use all three ports on the ATI Radeon HD 5770?
The movie version is that Mini DisplayPort does not convert directly to DVI, and the card cannot run three displays reliably unless you are using ACTIVE or POWERED adapters to convert to HDMI or DVI, which provide active conversion.
This is not your Mac Pro model, but you ARE using its display card, so these DO apply:
Mac Pro (Mid 2010), Mac Pro (Early 2009): Issues with three displays and multiple DVI, HDMI connections
Mac Pro (Early 2009), Mac Pro (Mid 2010): Supported display configurations

Similar Messages

Bootcamp 2nd monitor resolution changes upon restart

Here's my problem:
I have 3 monitors connected to my Mac Pro (specs listed below). Whenever I restart in Windows 7 (drivers updated, installed monitor control panel, Mac drivers updated) one of my monitors always gets screwed up with the resolution. I have 2 22" monitors and 1 28" monitor. The one that always gets messed up is the 22" screen with a resolution at 1680x1080. Windows 7 detects the resolution being about 600x800 or something. To fix this, I have to unplug the mini dvi port from the computer and simply plug it back in. The monitor instantly goes back to full resolution and then I have no issues until I restart again.
I don't seem to have issues if I leave 1 22" monitor and the other 28" monitor plugged in. This only happens when I have all 3 connected.
I've tried numerous times to update drivers and download the graphic card control panels, but none of it seems to help.
Would anyone have a clue as to why this happen?
Bootcamp - Windows 7 64 bit. (issue has happened even before I upgraded to 64 bit)
1 GB Radeon 5870
Model Name:          Mac Pro
Model Identifier:          MacPro3,1
Processor Name:          Quad-Core Intel Xeon
Processor Speed:          2.8 GHz
Number of Processors:          2
Total Number of Cores:          8
L2 Cache (per Processor):          12 MB
Memory:          10 GB
Bus Speed:          1.6 GHz
Boot ROM Version:          MP31.006C.B05
SMC Version (system):          1.25f4
OS 10.8.2

Strange. I naturally assumed that it would be the HDMI socket that has this issue.
Did a little digging and found this by Mr Grand Bennett. It was here: https://discussions.apple.com/thread/2746930?start=0&tstart=0
A related topic, but the same fundamental issues is being discussed nearby:
Can I use all three ports on the ATI Radeon HD 5770?
The movie version is that Mini DisplayPort does not convert directly to DVI, and the card cannot run three displays reliably unless you are using ACTIVE or POWERED adapters to convert to HDMI or DVI, which provide active conversion.
This is not your Mac Pro model, but you ARE using its display card, so these DO apply:
Mac Pro (Mid 2010), Mac Pro (Early 2009): Issues with three displays and multiple DVI, HDMI connections
Mac Pro (Early 2009), Mac Pro (Mid 2010): Supported display configurations

2nd monitor not using all available pixels

So am I the only one having this issue? -
I have a Mac Mini that is running Windows 7 in bootcamp. I have 2 monitors. My 2nd monitor is connected with an HDMI to DVI cable. In Windows, the whole screen of both monitors is used (edge to edge, top to bottom). But when I switch over to Yosemite, my second monitor has about a 1 inch bar of black on both sides and a 1/2 inch bar along the top and the bottom. This is literally unused space.
I've talked to Apple Support several times but they don't seem to have an answer. I get transferred to someone but each time I get cut off. (so I gave up trying to fix this over the phone or on line chat). There are no features or selections in the Syncmaster to adjust this. Why does it work perfectly fine in Windows but not when I switch over to Yosemite.
Maybe this doesn't seem like a big deal but it's so frustrating that I'm actually finding myself not wanting to use the Yosemite side.
Does anybody have a solutio

Sorry:
Display TypeLCD monitor / TFT active matrix
Diagonal Size20 in
Aspect RatioWidescreen
Native Resolution1600 x 900
Pixel Pitch0.2768 mm
Brightness300 cd/m2
Contrast Ratio1000:1 / 15000:1 (dynamic)
Color Support16.7 million colors
Response Time5 ms
Horizontal Viewing Angle170
Vertical Viewing Angle160
FeaturesHDCP, MagicBright 3, MagicTune
Dimensions (WxDxH)19.1 in x 7.9 in x 14.7 in
Weight9.7 lbs
ManufacturerSamsung model 2033SW

2nd monitor says in input - what to do?

Hello. I have been having trouble getting a 2nd monitor to connect with my computer on the windows side. Two days ago the monitor just quit working and says no input when I turn it on. I have checked drivers for HP, nvidia, and updated my apple software on the mac side.
Two days ago suddenly the monitor began working. I have no idea why. I suspected that updating the apple software might have finally kicked. It worked for awhile yesterdat morning but then suddenly quit and I've not been able to get it started again.
Any ideas would be appreciated.
Michael

Hi again Loner T. OK I read over all again. Let me see if I understand what you are saying to do:
First, download bootcamp software from apple-support-downloads. I found a place where it linked my computer to files and took me to bootcamp 4.0.4033. I follow directions on the apple site where it says to double click the file to uncompress it and then save all to a usb flash drive. That's what you mean above I think. I am gathering I download this on the apple side?
Open windows.
Go through and uninstall each of the windows drivers provided by apple that you have pictured above.
Then follow instructions on the apple website per what you say above by clicking on setup.exe.
This should reinstall the windows drivers and correct problems that downloads from windows may have created. Is that correct? I am thinking, however, that this is not the source of my problems. The install date on all these is 7-18-12 rather than a recent update that might have caused problems.
So I can do this. However, this doesn't deal with the issue of the nvidia graphics display card. Again, following other online suggestions for a clear install I deleted this file. The display card now does not show up in the Device Manager nor is there an Nvidia control panel in the control panel window. (The nvidia control panel, however, is still listed in Programs and Features as is a file called Nvidia drivers. What to do about this? I am assuming that this is needed for the display. I know the nvidia control panel was where I could see the connection with the monitor when this was working properly.
Thanks. Michael

Can't run flash player in full screen on 2nd monitor

Hi all! I have a laptop with dual video displays. The main
display is the laptop's LCD and the 2nd display is a 19" LCD
connected via VGA cable. I want to let a Flash movie loop endlessly
on the second monitor while I continue to work on the laptop. When
I drag Flash Player 8 over to the 2nd monitor and start the movie,
I can hit maxmize and it will take up the entire 2nd montior as it
should...with the file options and boarder around as expected. I
then hit Ctrl-F to go full screen and it snaps directly to the
laptop's primary monitor. I tried it at work where my desktop has 2
displays and the same thing happens. I need to force Flash player
to run full screen on the 2nd monitor and cannot find a way to
accomplish this. Any help is appreciated because it's driving me
nuts. I can always make the external monitor my primary but then
the start button and all my icons move there too and that is not
acceptable. Thanx!

Seriously? No one has any thoughts about this? I can't
believe I would be the first to come across this issue.

MacBook Pro performance issues w/2nd monitor and FCP7

I have this MacBook Pro bought brand-new in January 2010:
Model Name: MacBook Pro
Model Identifier: MacBookPro5,2
Processor Name: Intel Core 2 Duo
Processor Speed: 3.06 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 6 MB
Memory: 8 GB
Bus Speed: 1.07 GHz
and until today had never attached a second monitor to it. Today I hooked up my Samsung 24" to do some dual screen editing in Final Cut 7.0.3. I was unable to play back my video at full speed in the second monitor, and after a few seconds of skippy playback I'd get that error message about unable to play back video at full speed and to check my RT settings. I was using a Mini DisplayPort to DVI adapter. My computer has no issues playing the video in the laptop's monitor at any resolution and any quality settings (I've never changed the RT settings or anything else in the menu ever but I tried every combination this time). I then tried using my TV as a 2nd monitor with an HDMI adapter. Same performance issues. I then tried my friend's newer 13" MBP 8,1 and it performed flawlessly with the same project & footage. I feel like my $3,000 computer should outperform a $1,200 one even if mine is a year and a half older. Any advice?
Chris

Wow, you posted this perfectly to coincide with an identical problem, albeit using Logic Pro 9.1.5 rather than FCP.
Last week, I purchased a 23" external monitor to use alongside my "flagship" 2011 15" hi-res, 2.3 i7 Macbook Pro with 8Gb of RAM.
It is connected via a mini-DVI to D-sub analog (not that that should matter?) and all appeared fine.
The first issue I had was with my MBP's fan now running CONSTANTLY, when I have the second monitor attached. Even when the machine is completely idle.
When using the machine to record audio, this is a fairly hefty problem and not something I had anticipated - indeed why would I anticipate such a thing?
What is far, far worse though is that over the last few days I have had repeated problems with performance drop-outs and errors in Logic and I have trying to fathom out why. Realising that the only major system change made, was the above monitor connection, I ran some tests.
I restarted my MBP, no other apps were running and with my new 23" monitor attached acting as main display with MBP built in display on as secondary
I loaded up a fairly demanding Logic project which was hitting 40% to 60% CPU usage when using the built in MBP display last week
I ran activity monitor and had CPU usage history open
The above project now repeatedly overloads and playback halts in a given 8 bar section - with CPU at 80% most of the time
I disconnected the external display, no shut down, I just let the machine switch to the built in 15".
Started the same project, the same 8 bar section and hey presto - CPU usage back down to 40% to 60%
The above was reflected in the CPU usage history with the graph showing CPU use down by about a half, when running this Logic project WITHOUT the external display.
There is a very useful benchmark Logic project that has been used as a test by many users to gauge Logic performance on given Apple hardware.
The project has about 100 tracks pre-configured with CPU intensive plugins, designed to tax the CPU.
The idea is that you load up the project with tracks muted, press play and then unmute the tracks steadily until Logic us unable to play contiunously because of a system performance error.
On my MBP, with the external monitor NOT attached, I can play back around 50 of the audio tracks in this benchmark project.
With the monitor attached, I can get about 22 tracks playing.... which is actually a far worse a performance drop (-50% I think!?) than with the first example!
I did also try with just the external monitor attached and not the MBP display and performance was about 10% better than with dual monitors - so still extremely poor, to say the least.
This machine is the flagship MBP and has a dedicated AMD Radeon HD6750 GPU which should take care of most if not ALL graphics processing - I mean it's capable of running some pretty demanding games!
Putting aside the issue of constant fan noise, there is no reason AT ALL, why using an external monitor should tax the i7 CPU this way - it's not as though Logic is graphically demanding... far from it.
I am on 10.6.8, Logic 9.1.5, all apps up to date via "Software Update".
I will of course, be contacting Apple...

HT1338 cannot connect my MacBook Air to a projector -does not detect and 2nd monitor. I have a new Mini port to VGA cable made by apple. When I read online I see that many people have the same problem - Is this an Apple defect??????????????????

I cannot connect my MacBook Air to a projector - It will not detect a 2nd monitor or display. I am using an Apple made Mini Display port to VGA adapter. As I read online I see that many other peple are having the same problem. Is this an Apple defect!!???? If so it just burst the bubble about how great macs are. I never had a problem with that on a PC. I hope I am wrong. What can you tell me?

Hi There,
I have had the exact same issue but with a projector.
The issue lies with Mountian Lion 10.8.2.
I tried many a combination with no luck to get HDMI working.
Took my mac into the apple store and came to the conclusion it was the software, so I asked them to install 10.8 onto it (this is destructive so a backup is a must)
Bought my macbook home and voila, now displaying through my projector.
There is a small graphics update after 10.8.1 which seems to be the cause.
Hope this helps.
Thanks.

2nd Monitor won't work

I bought a Pavillion p6210f last week with Win7 loaded to replace my Dell/Vista. I was using two monitors with a VGA port and DVI port on the old PC, so I tried plugging in the same on my new HP and the DVI would not fit. In examining the pins I found that, althought the Manual said DVI, but the plug has the pin/bar arrangement of a DVI-D. So, I bought a VGAto DVI-D adapter and everything plugged in snuggly. All pins and bar appear a match.
But, it won't work. This is what is showing
NVIDIA nForce Serial ATA Controller HP RC Mirror Driver [Display adapter]
NVIDIA GeForce 9100 [Display adapter]
Acer P241W [Monitor] (24.0"vis, s/n LB4040014320, March 2008)the one working monitor....
After hours with the 800 support and hours of reversing the two Acer monitors, the DVI-D port is simply dead. Anything plugged in to the VGA works fine, anything and any combination plugged into the DVI-D and cable switching etc. the 2nd monitor is not even recoginized. The NVIDIA control panel doesn't recognize it. The amber power light just stays that way and nothing ever flashes on the 2nd screen. That is, it is the same as not plugging in at all.
I was less than pleased when 800 tech and supervisor suggested I take it to a repair center. A week old? I have put way too much setup and data transfer into the new HP to go back to the retailer for a replacement.
Techs didn't know, but could there be a DVI-X with the same pins that also fits

Eldric, did you update to the latest video driver from nVidia? It sounds to me like a driver problem. Update and let us know if that solves your problem.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Mac Pro 3.1 (early 2008) lags since I connected a 2nd monitor - HELP!!

Hey guys,
I just bought a 2nd monitor and i have lags every 5 seconds which
last about half a second (feels like 10 or less fps during the lag).
It happens with all kinds of applications. It gets worse with multiple
applications openend at a time. The crazy thing is that it only occurs
when i start to use both monitors at the same time. When i e.g. use
Logic 9.1 and use one monitor everything runs nice and smoothely
but as soon as i move the window slowly to the 2nd monitor i can
see the window lagging while I'm moving it. This is really annoying
because it seems not every input from the mouse/keyboard gets
into the system and its not a smooth workflow at all.
I switched the monitors connections but it didn't help.
Mac Pro (Early 2008) 2.8Ghz 8-core
Snow Leopoard ( 10.6.2 )
6GB RAM (2x2gb kingston, and the usual 2x1gb)
ATI 2600XT and 3 HDD.
1 Monitor 24" LG W2452T running at 1920 x 1200
1 Monitor 22" Samsung Syncmaster 2243BW running at 1680 x 1050
I really hope that you guys can help me out with this one.
What could be the problem? The ATI 2600XT should definately
be able to handle two screens at once with such little graphics
in logic 9 ?!
I want to run Logic 9 and an analyzer software (Spectre from AudiofileEngineering)
at the same time but its not possible with the LAG.
The problem/lags also occur when i sync the monitors.
Would a 2nd graphics card be a solution? But as I said
before its not a graphics demanding application.
Is it a hardware or software problem?
Summary:
- The whole System lags (not just one monitor) when
I start to use both monitors (having application windows on both).
I've got minor lags when using only one display and leave the
2nd one with the desktop wallpaper clean.
I tried:
-using only the 2x1 GB RAM which came with the mac pro
-using only the 2x2 GB Kingston RAM
Thank you in advance for your help guys!
Rick

Hey all,
I wasn't able to fix this yet.
I did everything I can think of. I even tried to wire
one monitor with a VGA cable but it didn't help.
I even have small lags when I am moving the Safari window
between the 2 monitors. Really little lags then but they
definitely are noticeable. I can make a video of that
if that would help someone understanding.
Hope there is someone out there who can help me with this.
Thanks already for any advice!
Cheers,
Rick
Edit: Do you think a new graphics card like the ATI 4870 would
help it? But I really don't want to spend more money just to
have 2 monitors while i have already 2 dvi connections on the
ati 2600XT.
Message was edited by: RickUnique

What cable do I need to connect a 2nd Monitor from the thunderbolt port?

Hi I have got one of the brand new iMac's with thunderbolt ports - what cable do I need to connect my Imac to a 2nd display either VGA or DVI - also is there a budget version about as well as I am sure its going to cost a lot from the apple store

Thanks I understand that I need another cable and have that from when I connected my old PC to the 2nd monitor.
http://store.apple.com/us/product/MB570Z/A?mco=MTY3ODQ5OTY - is this the one I need if going to DVI
I just dont want to waste more money on a cable that says its for an imac to 2nd screen and find it doesnt fit
For info my iMAC is the latest version (27" with the 2 thunderbolt connections and 1 firewire)
Thanks

How can i use my tv as the 2nd monitor

hi, how can i use my tv as the 2nd monitor, for example pull a video from desktop to tv for windows7, the computer is hp omni 120 all in one. because i have a cable for it that connects to the tv but i dont know how to connect the pc to the tv. i tried to go on the 'change screen resolutions' but that didnt help. thanks

Hi,
Here is it specs:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c03343048#N1221
You can only see:
Front:
1 - Screen area
2 - Microphone array
3 - Webcam camera
4 - Stand
5 - Speakers
Back:
1 - Optical disk drive (actually right)
2 - Stand
3 - Kensington lock slot
4 - Power button
5 - Memory card reader and other I/O on left side
6 - Motherboard back I/Os (specific I/Os are model dependent)
7 - Activity indicator
8 - Power connector
9 - LAN (ethernet)
10 - Four USB 2.0 ports
11- Audio port (actually left side)
Left:
1 - Hard drive activity indicator
2 - Memory card reader activity indicator
3 - Memory card reader
4 - Two USB 2.0 ports
5 - Microphone jack
6 - Audio port
Right:
1 - Optical disc drive
The only hope is "6 - Motherboard back I/Os (specific I/Os are model dependent)" area:
Please check area 6 above. As mentioned in my previous reply: Most likely your machine has no video out port.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Lightroom 4.2 - Experiencing problems with images viewed on 2nd monitor

Hi All,
This problem seems to have started with my updating from 4.1 to 4.2. I have my second monitor set as Loupe - Normal and Fit. As I crop an image on my main monitor, the 2nd monitor view does not always change to the cropped view. If I switch to a different photo and then back to the one I just cropped, the 2nd monitor view will then show the cropped image, but it is almost always blurry. Sometimes I can click the image in the 2nd monitor view to change to a 1:1 view and it will look sharp, and then click again back to Fit and then it too will be sharp. Other times I get a message in the 2nd monitor view that says "no image selected" and bouncing back and forth between a different image will correct this.
This all started off with the majority, but not all cropped images showing as blurred and progressed to what I have described above. I seriously though I had a focus problem with my camera!
Is anyone else experinecing this since updating? Suggestions?
Below is the suggested information to provide...
What version of Lightroom? 4.2
Have you installed the recent updates? Yes, 4.2
What operating system? Windows 7 Ultimate 64 bit
What kind(s) of image file(s)? All images are converted to .dng upon import
If you are getting error message(s), what is the full text of the error message(s)? No error messages.
What were you doing when the problem occurred? I am in the develop module cropping images etc.
What other software are you running? Silver Efex Pro 2, but I have had that installed in many prior versions of Lightroom
Tell us about your computer hardware. How much RAM is installed? 32 GB - Yes, I know - overkill...
How much free space is on your system (C:) drive? 119 GB of 223 GB of my solid state drive c:\
Has this ever worked before? Yes
If so, do you recall any changes you made to Lightroom, such as adding Plug-ins, presets, etc.? No other changes other than updating to 4.2
Did you make any changes to your system, such as updating hardware, printers or drivers, or installing/uninstalling any programs? No, no other changes.
Thanks!

Same problem. Not a soloution, but this may be relevant.
http://forums.adobe.com/message/4782916#4782916
Alan

Can I use a 2nd Monitor at 4K resolution (quad hd, 3840 x 2160 pixels)

HP Envy TS 17 Notebook, Product # E4S19UALaptop is running Intel HD Graphics 4600, and I have 16Gb memory installed. I use a 2nd monitor all the time via the HDMI port - works great. Both the laptop and the current 2nd monitor are running at 1920x1080 resolution (HD). I would like to attach a 4K monitor - (UHD-1) 3840x2160 resolution - 4 x "regular" HD (twice the horizontal and twice the vertical resolution). Will this laptop be able to operate the 4K monitor at 3840x2160 resolution (even at 30hz would be okay - not for games but rather for word processing, spreadsheets, software development)? Don't want to invest in the fancy new monitor if the laptop cannot drive it! Here is an exampe monitor: Samsung 28 Inch Ultra High Resolution LED Monitor (U28D590D), available on Amazon.com. Thanks!

Thanks for the information! As a suggestion, I have a copy of that manual, and it does indeed state precisely the information that I needed. Funny thing is, I looked in the TOC and the Index for anything related to external monitors and HDMI, and there wasn't anything that pointed to that page. Perhaps for future User's Manuals, the TOC and/or Index could include such references. Either way, thank you so much for the help! Also, for folks who are interested in higher resolution external displays, there is the option to use USB devices such as that from www.plugable.com to attach devices. I don't yet have their USB 3.0 4K compatible one, but I have been using their USB 2.0 HD compatible one for several years so that I can have 3 monitors (built-in, external, Plubable USB) - and it works very well. Flawless operation, though refresh rate is slow (not good for gaming). Which works for me, because it is mainly for surfing and email.

2nd Monitor

2nd monitor switches itself off after approximately 30 minutes and then goes on/off intermittently every 10 mins.
No particular pattern, but wonder whether heavy graphics work in Photoshop CS4 is a pointer? Unable to use the EIZO monitor for work.
All cabling good. No problem with iMac 20"
Regards

@phyly44
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

2nd monitor W2072a suddenly has no signal

2nd monitor W2072a suddenly has no signal, tried switching cables & rebooting but box comes up states Scanning then No Signal. I desperately need help since the only way I can use a computer is with 2 monitors due to a disability

Hi ToniClark,
Welcome to the HP Forums! I see that you have issues with your secondary monitor. What happens if you disconnect the first monitor that is currently work and just hook up the W2072a by itself? If it works then we know it is something with your computer system and if it still fails then their could be a problem with the monitor.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Bootcamp 2nd monitor

Similar Messages

Maybe you are looking for