Bootcamp Assistant will not recognized Windows 7 disc

I am running a late 2009 Macbook Pro with 10.8.2, trying to install bootcamp but when running the Bootcamp Assistant my Windows 7 - 64 Home Premium disc is not being recognized, I get a error " The Installer Disc Could Not Be Found Insert your Windows installer disc and wait a few seconds for the disc to be recognized"
The drive just tryes to run over and over but never mounts the disc.
Any recomendations?

make sure you install the apple hardware drivers the correct video card driver is required to use external displays
one can make a driver stick in bootcamp on osx or one can download the zip file with drivers from apple

Similar Messages

TS4531 Bootcamp: Hdmi display not recognized windows 7

i have a late 2012 macbook pro retina with bootcamp windows 7 installed, when i try to connect a display on the hdmi port, nothings happen
its like theres drivers missing for the hdmi port. i tried all possible things, went to screen resolution options on control panel and connect external display options.

make sure you install the apple hardware drivers the correct video card driver is required to use external displays
one can make a driver stick in bootcamp on osx or one can download the zip file with drivers from apple

Adobe Download Assistant will not install.

I'm attempting to install the trial version of Design Premium CS5.5, but the Adobe Download Assistant will not install. It appears to be installing after I click on the installer--a window loads that says "Installing"--but then nothing happens. Nothing loads. Nothing shows up in the Applications folder. After trying this many, many times (with different browsers and after many refreshes and computer restarts), I'd sometimes get an error message that I need Adobe Air. When I try to install Adobe Air, I have the same issue: nothing happens. What can I do? I am using a brand new MacBook Pro.

I had a very very similar issue on my MacBook Pro as well with ADA. Solved it about 30 minutes ago. I found a post from late December that suggested trying the following:
System Preferences
Energy Saver
Uncheck "Automatic Graphic Switching" at the top of the page.
Install Adobe Air
Profit.
Hope it works for you too, I was ready to throw this box out the window.

Airport Extreme unit will not allow Windows devices to access WiFi

For the last 10 or so days, my Airport Extreme unit will not allow Windows based devices to access WiFi (ASUS laptop and Nokia Windows Phone). Our Apple devices have no issues (MacBook Pro, iPad, iPhone, iPod). Settings were not changed but there may have been a program update? Have tried resetting without success. Today I tried to bypass the problem by creating guest network access - my MacBook Pro can access the guest network, but again, the Windows-based devices can't log in.
Airport packaging stipulates that this product will service both Apple and PC products. I'm stumped and this is a bit of an issue as my wife's PC has been cut off from the Web as well as my Windows phone. This Airport unit is fairly recent having been bought August or September of last year - so a recent purchase, but to get Apple assistance it appears I'd need to purchase service ticket... (Am using Mountain Lion 10.8.4 and Extreme 5th Gen.)
Is there an easy solution?

No software updates available.
Found a Network Options checkbox which blocked IPv6 connections in Airport Utility. Unchecked it, that didn't change anything, so I've returned it to its original setting. But under Internet Options, Airport is set to allow IPv6 connections. Strange that this unit would have settings that appear to contradict each other.
There was an access control panel - but to grant control here, I'd need an Apple address which my Mac would have but which the Windows devices would not, so that setting couldn't be used to address this problem.
So, no solution to the issue that I can see.

HP Support Assistant will not run

I'm trying to update to Windows 10, but keep getting the error code 80070003 and I have tried everything that has been suggested to me in the Microsoft community. I have also noticed that the HP Support Assistant will not run. Please help! dfreehill

Hello, and Welcome to the HP Support Community! Which HP device are you using? Are you using the "Update this device" or the "Media Creation" method? I updated 3 PC's today using the suggestions from here: http://www.theverge.com/2015/8/1/9083501/microsoft-windows-10-update-download-how-to-guide WyreNut

Backup Assistant will not accept my PIN

Backup Assistant will not sync from the phone. It keeps saying the PIN is invalid, even though it is the PIN that it sends when asked.
How do I get the PIN to with?

Welcome to the world of Mac. Some ‘light’ reading to help the transition. I don’t recommend trying to get through all of this at once.
 A guide for switching to a Mac
Anatomy of a Mac
 Mac Basics—Tutorials on using a Mac
 Mac OS X keyboard shortcuts,
Mac Basics – Switching From Windows
Mac OS FAQ
MacTips,
Quick Assist
Switch Basics
Switching to Mac Superguide
Switching to the Mac: The Missing Manual, Mountain Lion Edition
 Take Control E-books
 Welcome to the Switch To A Mac Guides

Adobe download assistant will not work on my machine?

Adobe download assistant will not work on my machine. When i try to start it i get a message saying "Sorry an error has occurred. This application cannot be installed because this installer has been mis-configured. Please contact the application author for assistance." Any ideas what to do

Are you using Mac OS? If so please try removing the Adobe Download Assistant from your Applications folder and try again. This issue is documented in the Known Issues section of Troubleshoot Adobe Download Assistant - http://helpx.adobe.com/creative-suite/kb/troubleshoot-download-assistant.html.

Adobe Download Assistant Will Not Recognize My Adobe ID

I've been an Adobe customer / forum user since before ID's were tied to email addresses. My product registrations going back to 1996 through CS 5.5 apps are recorded under that ID. Since I have to change my email address every couple years to escape spammers, I do not want to change my Adobe ID (and go through the hassle of re-recording the record of registered apps) to a "fluid" ID like an email address.
Automatic registration and now Adobe Download Assistant will not accept an Adobe ID that is not an email address, yet I can still use it to 'manually' register new / upgrade product purchases. The problems this poses are two-fold:
Since I can only manually register new / upgrade products, I cannot obtain any "registration bonus" downloads.
I cannot download trial versions of apps I want to check out.
Adobe needs to get its act together and tell its gen-X / Millenials / Kid Web and software development staff that not all Adobe IDs are email addresses, but might also be a unique user ID string.
Further, due to an individual's email address volatitility (virtually everyone in my email address book had their email address change every 2- 3 years due to ISP demise, merger, personal relocation, job change etc.), Adobe should return to - or at least give precedence to - the model of UID / PW authentication instead of email address / PW authentication. This would lower Adobe maintenance effort / cost for user accounts as one could simply sign in with UID + PW and change email address for the account as necessary. As it is now, Adobe CANNOT deal with a user whose email address changes.
When Adobe changed from UID precedence to email precedence, I could not register Acrobat Pro (2007) during registration so I used my email address at that time to register the product. When that email address ceased to exist, I tried to get Adobe to transfer that registration to my old [non-email address] Adobe ID, and, over several months of email exchanges, they ended up admitting they could not do it. I could not make the change as the SN was already marked as used in there system so simply re-registering it to my existing account wouldn't work either.
This has been an ongoing issue with "legacy" users since 2006 at least, and NEEDS TO BE RESOLVED ASAP!!!!
Wayne M Cole AGCV CSCV, CLVI
Proprietor
IHP Legal Video Service
Infinity Heart Producfions,
Contributing Editor,
Government Video Magazine

There you go MISSING THE POINT AGAIN!! My Registered products WILL NOT FOLLOW MY UID IF I CHANGE IT, NEVER DID SINCE 2007. Saying the will is false information which I alerted Adobe to back in 2007 and is a problem y'all never fixed.
Just a little over a week ago, I got I got LightRoom 4 ug from a LR 3 I had purchased in March. Signing on with my legacy UID (non-email) allowed me ADD those registrations to my account, as I had cor CS 5.5, 4, 3, etc. etc. Now, isn't it odd that the very day after I posted here, when I sign in to my account it shows NO REGISTERED PRODUCTS!!! If I look at my order history, it has orders from Adobe store from last weeks CS6 MC purchase back to 2007 when I started buying from Adobe directly after the local brick and mortar resellers disappeared.
So I try to register CS6 MC, it tells me the SN is already in use. I try open a PDF document and it tells me I have to first register and agree to the Acrobat Pro X license before I open a doc - and it was an UPGRADE FROM CS 5.5 MC. I try to run CS 5.5 apps and they tell me I have to purchase a license since the trial period is over - HUH! Until I posted here it was working FINE. I go back to my acccount (non-email UID sign in) and check my profile - Lo and behold SOMEONE (not me) has changed the UID to an email address instead of the non-email UID I sign in with AND DELETED ALL MY PRODUCT REGISTRATIONS!
Naturally, your software does not let me put it back to the same UID I use to sign on with so THE LINK TO ALL MY REGISTERED PRODUCTS IS GONE, I CANNOT REGISTER NEW ONES (which was no problem just a day or two before posting here) WHICH PROVES WHAT I WAS TOLD IN 2007 - WHEN YOU CHANGE UID'S YOUR LEGACY REGISTRATIONS WILL BE LOST!!!
So, in summary you (Adobe at least, and I suspect you personally) went in and messed with my legacy account, deleting all my registrations, as I was told in 2007 would happen and advised to keep the old UID if I did not want to blow away those registrations, when I explicity did NOT want to make such changes. And, should I need an SN for some upgrade offer or to install an update for an older product that I did not transition to the new facility, I have to HOPE that I had I can find the original purchase invoice and that there is a copy of the SN / Reg card attached to it.
THANKS A PANT LOAD!!

Will Not Boot from Install Disc & 4SNS/1/40000000: TG0D - Thermal Sensor?

*Will Not Boot from Install Disc*
I used the "option key" approach with the gray start up disk. At first it ejected the start up disk. Then I nudged the disk back in the machine and it showed on the screen as an option. I clicked on the start up disk image and it finally loaded.
But, it won't accept the start up disk when holding down the "C" key at restart.
*4SNS/1/40000000: TG0D*
I did an Apple Hardware Test and received the following diagnostic:
Version: 3A121
Test Suite: Extended Test
Loop Count: 2
Result: Failed
Failure code: 4SNS/1/40000000: TG0D
*Thermal Sensor*
A search for the failure code 4SNS/1/40000000: TG0D brought up an Apple Discussion topic entry stating: That error code indicates a problem with a thermal sensor. It could be not working or possibly not connected. You will need to take it to Apple for repair.
Would a thermal sensor have anything to do with it not starting up when holding down the "C" key at restart? What are thermal sensor problem symptoms?
*User File Folder Opened Up*
The machine also starts up with my user file folder opened up rather than with a blank screen as it normally should
I completed a DiskWarrior rebuild on the disk and verify disk shows it is fine.
Any suggestions on what to do next with these issues?

The answer was in your post: "You will need to take it to Apple for repair."

G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
We were in the process of installing 10.4 Tiger before placing it for sale.
The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
We have done the following during our troubleshooting:
- Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
- Remove RAM 1 stick at a time and reboot
- Replace RAM with RAM from another working Quicksilver
- Replace Video Card with one from another working Quicksilver
- Zap PRAM
- Reset CUDA switch
- Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
- Tried booting from the Macintosh Server G4 Software Restore CD
- Tried booting from Mac OS X Server CD
- Tried booting from AppleCare Protection Plan CD with TechTool
- Tried booting from Diskwarrior CD
- Tried booting from an external FireWire drive with a disk image of Tiger OS Install
- Tried booting with the hard drive disconnected
The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
I would look at the CD drive cables, etc, and see if another drive gives different results.
You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
HT1310- Startup Manager: How to select a startup volume

K7N2G will not load windows xp with any type of dvd/cd drive installed?

This is on my old computer, the specs are as follows
k7n2g
athlon 2600+
radeon 9700 pro
Caviar SE wd800
1gb samsung ddr333
It does not matter if it is keyed as master or slave, primary or secondary my old k7n2g will not load windows with a cd drive installed. I have tried three different drives and everything that I can think of, changed cables, channels, drives, everything. Windows just hangs. I cannot even get into safe mode. Is this an IRQ problem? The drives keeps trying to eject themselves, no matter what kind I use. This has never happened before, but there was a point before this problem where the vga wouldn't kick on (at the login screen) until I hit eject on the cd drive. This is driving me crazy and I have a girlfriend who just has to play her stupid sims and will not stop bothering me about it. PLEASE PLEASE PLEASE help me!
Thanks
Chris
PS here is my NEW workstation (I couldn't be happier to get rid of the old system)
two Opteron 250 90nm
2gb 2-3-2-6 Corsair Reg/ECC DDR 400
Tyan Thunder K8WE
1x BFG 7800GTX OC (one for now)
Audigy 4 Pro
Seagate Cheetah U160 10k 73.4 gb
Atlas V U160 18.3 gb
Lite on Dual Layer burner

Your Tyan based hardware listing on the first post has no relevance to anything, and might only serve to confuse. Please remove it and put the hardware you are trying to troubleshoot in a signature. Look in your profile>Forum Profile Information and enter that in the Signature box. That way we wont have to scroll to hunt down your hardware specs
So let us get this straight.
This system used to work fine? Yes? Then what prompted you to reload the OS?
You mentioned that didn't happen when you owned it. Are we to assume that at some point you sold or gave parts of this system to someone else? If so, what changed?
A little more history might prove useful in helping us to give you better suggestions.
Look at the PSU and give the Amps for the +3.3, +5v, & +12v lines.
***Edit, from what I see on the net, that is a dual rail PSU and the amps are as follows:
+3.3V@22A, +5V@21A, +12V1@18A, +12V2@16A
Is this correct?
Both the 3.3 and +5v seem a little low to me, but I am not entirely convinced that would be your problem. However, the fact that the 12v rails are split, can lead to other problems such as overvoltage protection circuitry getting in the way. Especially if the 16amp 12v rail is overloaded.
This is something to consider. Just because it is supposedly capable of wattage over it's rated power output doesn't mean it can handle what you're throwing at it all at once. If you have a single rail PSU that has at least 18 amps on the 12v rail to test with, we could almost definitively rule out power as the sole problem or a contributing factor.
I have never had a CD rejected, but if you could be more detailed about what you have connected to the board while attempting to load the OS, and then a detailed description of at what point the OS installation fails, and the CD is ejected, that would be helpful as well.
The fact that you've tried several drives, cables, with the same result. And also had a blackscreen event, does point to at least one problem that could point to a power issue. The CD rejection issue is foreign to me since I usually use the same type of PSU in all my builds or ones that I know work with a particular set of hardware, so I can't attribut that to a power issue.
Did you try clearing the CMOS and then initialize the default settings?
Do you have a cheap AGP card to try instead of the 9700?

DHCP snap-in will not retain window settings, columns, etc.

DHCP (version 6.3) will not retain window settings or columns after being closed. I haven't been able to find any information on this so far. Has anyone else had this issue?

Hi,
I understand your issue. The DHCP management console won't save the view customize settings.
We could customize the DHCP management console using MMC (Microsoft Management console)snap-in, customize it and save it to a place. Doing this makes the console remembered the configuration.
More information regarding MMC, please take a look at the below link:
Microsoft Management Console 3.0
For the DHCP management console does not remember the customization, this might by design. If we want to make a customized DHCP console shortcut, we could take a try to enter DHCP in author mode, more detailed steps, please take a check with the post of
Josh in the below thread:
DHCPMGMT.MSC in Remote Server
Administration Tools (RSAT) won't remember DHCP server
Hope this may help
Best regards
Michael Shao
TechNet Community Support

Clicking on an e-mail address will NOT open Windows Live Mail which is already the default mail program which is already set as the default mail program

Clicking on an e-mail address will NOT open Windows Live Mail. Windows Live mail is already set as my default e-mail program.

Sorry you're having this problem. I think it was previously reported only by Windows XP users.
When you reinstall, were you making Firefox your default browser? Some users have reported that ''not'' making Firefox the default browser was an effective workaround.
However, you may have success with this approach, suggested by a user in another thread, which appears to more thoroughly update the Windows registry:
# Open Adobe Reader / Acrobat
# Edit->Preferences
# In the Categories column click 'General'
# Near the bottom of the page click the button marked 'Select Default PDF Handler'
# In the dialog, select 'Adobe Reader XI' (or Adobe Acrobat, as the case may be) and click 'Apply'
# A Windows Configuration screen will appear. Allow it to do its stuff (takes a few minutes), then restart your computer when prompted.
Does that resolve the issue for you?

I'm not a "Cloud" member. I just upgraded to Lightroom 6 from Lightroom 5. All was working well yesterday. Today Lightroom will not open (Windows 7). I see the logo photo over my Lightroom platform but nothing loads and I see "Lightroom not responding

I'm not a "Cloud" member. I just upgraded to Lightroom 6 from Lightroom 5. All was working well yesterday. Today Lightroom will not open (Windows 7). I see the logo photo over my Lightroom platform but nothing loads and I see "Lightroom not responding." I checked the catalogs and see that lrcat-Journal and lrcat-Lock have been created every time I try to open. I have a backup from the first day I upgraded, but Lightroom doesn't want to access it. Should I reinstall?

Well, is the catalogue (and the folder it is in) writable? Have you actually checked the permissions? Lightroom won't be spitting out the error just to tick you off, and - computer wizard or not - this sounds very much like something you'll have to fix at the OS level: it's probably nothing to do with Lightroom or those funny lads at Adobe.
Some light reading for you, courtesy of the site search: https://forums.adobe.com/search.jspa?q=%22+not+writable+and+cannot+be+opened%22&place=%2Fp laces%2F1383621&depth=ALL
It would help to know your OS.

Will not read Office:Mac disc

After reading that the new Intel-based Macs will run MS Office for Mac, I tried to install it onto my new MacBook Pro. However, the disc drive will not even recognize the disc. The drive will make strange struggling noises before spitting the disc back out.
I have used the disc 2x before on PowerPC-based Macs... there is one product key still available and I'm positive that there is nothing wrong with the disc.
Any suggestions?

Applechique --
Welcome to Apple Discussions !!
One thing to check first . . .
Did you uninstall (not just trash) your MS Office Test Drive?
I believe the Demo?Test Drive came installed on your new MacBook.
I think there is an uninstaller in the Office folder.

Bootcamp Assistant will not recognized Windows 7 disc

Similar Messages

Maybe you are looking for