Bootcamp crashed removing partition, now stuck with 60GB "Free Space"
I have a MacBook Pro Retina, 15-inch, Early 2013 with a 250GB hard drive running Mavericks 10.9.3
I use to have a 60GB windows partition setup via bootcamp, but I haven't used it in a while and wanted the space back. Bootcamp crashed half way through removal, and now I have a 60GB of Free Space that I am unable to resize the existing Mac partition into, nor can I use that space to create any new partitions. I try and no error appears, yet when I leave the partitions tab it says I've got unsaved changes.
I've gone into recovery mode and run a repair disk, and to resize it while still inside recovery mode. Nothing seems to help.
Does anybody have any suggestions?
I have a MacBook Pro Retina, 15-inch, Early 2013 with a 250GB hard drive running Mavericks 10.9.3
I use to have a 60GB windows partition setup via bootcamp, but I haven't used it in a while and wanted the space back. Bootcamp crashed half way through removal, and now I have a 60GB of Free Space that I am unable to resize the existing Mac partition into, nor can I use that space to create any new partitions. I try and no error appears, yet when I leave the partitions tab it says I've got unsaved changes.
I've gone into recovery mode and run a repair disk, and to resize it while still inside recovery mode. Nothing seems to help.
Does anybody have any suggestions?
Similar Messages
-
Yosemite will not upload on my MacPro, says I have to verify or repair, but when I do - it fails on that too. Am now stuck with a computer that doesn't work ! Have I lost everything ?
Hello BassoonPlayer,
Since you are using one of the the school's Macbooks, it is quite possible that the time and date are not properly set on the computer that you are using. FaceTime will not work if you do not have the proper time zone set up for the location that you are in. This past week, there were a two other Macbook users I've helped by simply telling them to set the Date/Time properly. By the way, you described your problem very well, which makes it easier for us to help you. Hope this solves your problem -- if not, post back and I can suggest other remedies.
Wuz -
I was fooling around with the "reader" feature on my New iPad. I am now stuck with that and can't get out. Even my four digit code is read out in a machine voice and the iPad wont boot. How do I get out of this. Tried the red arrow slider. shut of the iPa
James,
I cannot get into Settings! It keeps reading out Slide to Unlock when I try to slide teh arrow to open the fpur digit entry boxes. -
I just updated my phone and it is now stuck with usb cable and itunes logo and itunes on my computer says I have to restore. Can I get my phone working again without loosing my photos?
There is no other way than to plug into a computer to restore the phone. You can use another computer to do so, but in case you did not back up to iCloud your data and settings will be gone.
Follow this article to connect in recovery mode:
iOS: Unable to update or restore -
while updating ipod touch 4 i got an error message now stuck with apple symbol and empty bar. can i restart ipod?
- What was the error message?
- Try closing iTunes and then disconnect the iPod from the computer. Then reconnect the iPod. If the iPod shows in iTunes then you can try again. However, You should try to resolve the error message first.
- If iTunes does not see the iPod try reetting the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- I recommend that you come back with the what the error message said and the condition of the iPod and if it is visible in iTunes. -
HT4623 I tried to install iOS7 and am now stuck with the this message on the screen send via mail
I have hust installed iOS7 and followed all the steps. I am now stuck with a message on the screen which doesn't move. Licence agreement and when I say I agree noting happens. What am I doing wrong??
Reset iPad and start again.
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
Up now stuck with reading list as unticking in safari preferences gas not worked
Trying to use facetime on mac air to ipad cannot get contacts up; now stuck with reading list as unticking in safari preferences has not worked how do i get rid of reading list and add contacts to macair please?
This seems to have been fixed by going to settings>iCloud, deleting Safari, and then adding it back again, effectively resetting iCloud for Safari on the iOS device.
-
Whilst synching to my PC it said there was a software update for the iPhone.
It is now stuck with a message saying connect to iTunes. I've tried resetting it in various ways but it still comes back to Connect to iTunes, but it won't.
Help!See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
But... if the Device has been Modified... this will Not necessarily work. -
I try to install it, but i select my free (fresh formated) partition with 35GB free space and i see:
Setup was unable to use existing system partition because it does now contain the required free space.
if i select partition with partition that does not contain the required i see
"Windows cannot be installed to Disk 0 Partition 1. (show details)"
so what is it? what can i test?
My Disk has 250GB, my partitions:
C: 8MB - Boot (7MB Free) - FAT
D: 37,5GB - WINXP (27,9GB Free space) - NTFS
E: 35,3GB - New (35,2GB Free) - NTFS - i want to install on it
F: 160GB - Data (6GB Free) - ntfskolorafa_ said:
I try to install it, but i select my free (fresh formated) partition with 35GB free space and i see:
Setup was unable to use existing system partition because it does now contain the required free space.
if i select partition with partition that does not contain the required i see
"Windows cannot be installed to Disk 0 Partition 1. (show details)"
so what is it? what can i test?
My Disk has 250GB, my partitions:
C: 8MB - Boot (7MB Free) - FAT
D: 37,5GB - WINXP (27,9GB Free space) - NTFS
E: 35,3GB - New (35,2GB Free) - NTFS - i want to install on it
F: 160GB - Data (6GB Free) - ntfs
Is this 8MB "Boot" partition (formatted as FAT???) something you created when you partitioned this disk for the Windows XP installation, or is this an 8MB OEM partition that you've somehow assigned drive letter C: to?
I wouldn't be surprised at all that your error message is being generated because thsi "BOOT" partition, labelled as drive C:, is only 8MB in size, and you can be absolutely positive that an 8MB partition is going to generate this error: "Setup was unable to use existing system partition because it does not contain the required free space."
The correct answer really depends on whether that drive C: is the boot (sic) (the proper terminology is to call it the system partition) partition for the Windows XP installation. If it is, then you're going to have some repair work to do on your Windows XP installation first, so that you can free up that 8MB partition.
In any event, I'm fairly certain that the solution is going to require the removal of that 8MB partition, as you've suggested in your most recent post.
Lawrence Garvin, M.S., MCITP(x2), MCTS(x5), MCP(x7), MCBMSP
Principal/CTO, Onsite Technology Solutions, Houston, Texas
Microsoft MVP - Software Distribution (2005-2009) -
I was partitioning my HD to allocate free space to give to my windows partition in Boot Camp. Now I cant access my windows partition at all. Please help
TTBOMK the only way you can increase the Windows partition is to repartition the drive back to a single partition
Then reinstall Mountain Lion
Restore all data from backup
Create new larger partition with Boot Camp
Install Windows
Restore data from backup
Allan -
Error message while burning DVD with Premiere Elements 13 with Mac Book Pro i7/7200t/mn with 60GO free space available on gard drive. message: "erreur logicielle interne: DVA/premiere/elements/pre12/pre-mediacoreCS7". can someone help burn my DVD (the file goes very well with chapters and scenes before burning). thanks very much, response appreciated, Alain
-
Now it's stuck with the progress bar less than a quarter full. I have also tried resetting through itunes which works right up to the point where itunes states that it needs the passcode to be inputted into the ipad to connect to it. At which point it then sticks at the same progress bar point. HELP!! please, this ipad is really important to my work.
Well the term "hotlined" I have never heard before. In any case many states (like NY) just passed regulatory powers to the State Public Service Commission of which it may be called something different in your state. You could file a complaint with them. Or file a complaint with your state attorney generals office, they also take on wireless providers.
The problem here is the staff you speak to are poorly trained, in days gone by it took one call to them and they pulled up your account and see the error and had the authority to remove any errors. They did not remove legitimate account actions, but used their heads instead of putting a customer off or worse lying to the customer.
Its a shame you have to go through what you going through.
Good Luck -
Two days ago I rebooted to Bootcamp Windows 8.1 and it blue screened. I have been trying for two days to fix my system following helpful posts here and I'm just digging myself further into confusion and complications. At this point I'm extremely in over my head. I have removed the Bootcamp partition using Boot Camp Assistant and tried re-installing Windows again and again using BCA…
At the moment I am back to no Windows partition, just a 3TB OS X partition, but when I try to create a Windows partition it gets created as a logical core... heck, I don't understand enough, just know it's not right.
How do I get my drive tables all right again and then be able to create a working Bootcamp partition? What screenshots do I need? I appreciate any help I can get.Okay, I used Bootcamp to create a EFI-bootable USB drive with Windows 8.1
I had my drive back to a single 3TB partition.
I created a Free Disk (empty) partition of 750GB (which was then set as 876.82GB).
I rebooted.
Created a new partition, got the notice that Windows will create a smaller 128 MB partition.
It did create the 128 MB partition, or showed such.
Then when I go to format the other, last free space partition it seems to work.
When I go to install Windows 8.1 in that partition I am told Windows cannot find a partition to install into.
Here is my diskutil list as it is now.
… and I just saw the "must be under the 2TB limit" again… I don't know how I had Bootcamp working until last week. It was cleanly set up on my new Mac as ~750GB the first time with BCA and worked for months until whatever changes were made with 10.10.3. -
Did a factory reset on my phone and the screen is now stuck with apple symbol
I have done a master reset/restore facoty settings on my iphone and am now stuck on a screen with the apple icon
I had that same thing happen to me when I was updating my iPhone to iOS 5! What I did was I just kept resetting and resetting and holding down the home and power buttons until 3 in the morning. (ok, maybe it was only midnight but it sure FELT like 3 AM!) Anyway, I would just keep at it until it decides it wants to cooperate. Mine eventually did.
-
I have iphone 3gs 32 GB attempt to Reset-Erase all settings now stuck with Apple logo
I have iphone 3gs, i have downloaded free games and apps from app strore installed and it was working fine. i even updated the games a couple of times. Two days ago I attempt to Reset-Erase all settings & Content of my phone. It was stuck with apple logo. till now. What to do? Now it is stuck there and when I connect it to my PC it does not appear there also.
It is just charging and chargning only. when i disconnect it shows battery low.
Help please. Please... Please...............Force the phone into recovery mode & restore it:
Turn your phone off. Leave the USB cable connected to your computer, but NOT your phone, iTunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new.
Maybe you are looking for
-
Dual 23" displays showing distint difference in color and brightness
Today I purchased a second 23" cinema display to run a dual display set up. I am now noticing that my first display, purchased about a year ago refurbished from apple, is distinctly darker and has a slightly yellowish tint to it in comparison to the
-
Image Prompts in OBIEE 11.1.1.5
I am able to display an image as a logo on an analysis using the fmap notation... say fmap:Images/myimage.jpg. However, I am unable to use the image in an Image Prompt using either the fmap notation or explicit URL. I have uploaded the image to 2 loc
-
Subquery inside Merge Into under 11g
create or replace PROCEDURE SP_IN_CURRENCY IS CURSOR csr IS SELECT currency_code FROM in_currency ORDER BY currency_code; v_hkd_rate NUMBER(15,9); BEGIN SELECT spot_rate INTO v_hkd_rate FROM in_currency WHERE in_currency.currency_code = 'HKD'; MERGE
-
Hi, All, I just find a problem in my Flash builder generated .swf file. We used "Merged into code" option when I compiled the project, My preloader was showed just fine. But if I use "RSL" and also use some exteranlly loaded library files, the preloa
-
Victor, I find Tor's and Greg M's bpcatalog documents describing AJAX and JSF useful. However they do not address 'updates'. Updating the model via an AJAX request that is handled by the JSF framework as suggested by bccatalog examples is a challenge