Bootcamp... not booting

I am trying to install bootcamp on my early 2008 mbp; when bootcamp restarts to boot into windows it just displays the gray screen and freezes. When I hold option to get into the disc it freezes at the same place. Is there anything else I could try? The XP disc is a SP2 home edition retail.

I had the same thing, had to wait a little longer and it worked
Was not frozen after all
But the thing is I get this grey screen for 2/3 minutes every time I boot :/

Similar Messages

  • Bootcamp not booting to Win7

    I have a 15 inch MBP late 2011 running Lion.  I have Bootcamp and boot to Win7 for 1-2 programs.  I've had my MBP for about 5 months and had no problems with booting to Win7 until the last month.  Now, about 80% of the time, when I try to boot I will freeze at the OS selection screen.  I will have to hold down the power button and have to reboot into Lion.  I've tried to detect a pattern with the times that it will let me boot to Win7, but unfortunately I can't determine that pattern.
    Anyone else running into this?

    low disk space
    a recent April patch tuesday
    .... other causes
    when you do boot windows, use CCleaner to get rid of temp files, fix the Registry,
    go into Disk Cleanup: System Files - remove any in there
    make sure you have enough free space. When you installed and got the SP1 update, that needed about 9GB temp space to apply the update, having 20GB free is a good idea and not waste at all
    very low and you can find you can't login
    After all that do a chkdsk scan for bad sectors
    Make sue that you have enabled create restore check points
    The place to begin - and you can get an idea even from OS X side, is see how much space there is and boot from Windows 7 DVD and let it try to do automatic system repair

  • Bootcamp w/ Windows 7 - will not boot

    Hi there,
    Whilst edited the msconfig setup on my Windows 7 64bit partition (which I've done a good few times before) I stupidly checked the 'use original boot configuration' thinking it was a 'return to defaults' synonym.
    Now when I attempt to boot into Windows, I get the following error message, before any Windows logo appears:
    'Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
    1. insert your Windows installation disc and restart your computer.
    2. Choose your language settings, and click "Next."
    3. Click "Repair your Computer".
    Status: 0xc0000225.
    Boot selection failed because a required device is inaccessible.'
    Corrective steps so far:
    I have the original Windows CD from when I bought it, but I can't manage to make Windows boot from that instead of internal storage so no startup repair or restore options which apparently is all I need to fix this error...
    I'm, not sure whether this is just because of bootcamp not recognising the disk properly or my optical drive playing up (which is has done with some disks pretty much since I bought the mac, although does boot successfully from the Mac OSX disk I tried).
    I've also tried downloading the same ISO image and creating a bootable USB flashdrive but that won't boot either - again, not sure whether this is because bootcamp won't support it (I've heard Apple's firmware doesn't like booting from flashdrives much), or whether the USB should be formatted differently etc (it's currently formatted as NTFS but am now wondering if trying again with FAT32 would make any difference).
    I've also installed ReFit and am running that successfully, which recognises the USB disk but also can't boot from it. Tried the MBR and GPT sync tool too which said there wasn't a sync problem anyway.
    I can't access any boot options for Windows (Safe Mode etc), each attempt is faced with the same error; can only choose to boot Windows or run the memory diagnostic tool which I doubt would help.
    Obviously can't access any BIOS as that doesn't exist on macs.
    Can I replace any specific boot file on the windows partition remotely?
    Please help! I'm running out of ideas and really don't want to try and re-install Windows!

    I would, but as the apparent guarenteed solution is to boot from the Windows CD, and I believe bootcamp is preventing this, I'd assume it'd be more relevant here.
    Will probably do both though though, makes sense, as you say.

  • Bootcamp: Windows 7 not booting on 4gb ram

    Hi!
    Situation: 
    I installed Windows 7 via Bootcamp. On 2gb ram (2x1gb or 1x2gb doesn't matter) windows boots fine.
    I upgraded to 4gb ram (2x2gb) and now Windows is not booting. As far as I know, it's not even getting in DOS.
    There's just the cursor blinking into infinity...
    What I've tried so far:
    Installing windows with 2gb and ugrading to 4gb.
    Installing windows with 4gb
    Tried the 32bit and the 64bit version
    Found a 'solution' on the web making me boot in safe mode in order to change the maximum ram windows accepts.
    Attributed more gb to the windows partition
    I'm out of ideas, what do you think?
    regards,
    Massimo

    While we all have MacBooks in this forum not all of us use BootCamp. There's a BootCamp Support Community where everybody uses BootCamp. You should also post this question there to increase your chances of getting an answer.
    https://discussions.apple.com/community/windows_software/boot_camp

  • Bootcamp volume selectable in Startup Disk but won't boot. Bootcamp not visible with Option Key

    My bootcamp volume is selectable in Startup Disk System Preference, but Windows 7 will not boot stating no bootable volume.  The Bootcamp volume does not appear when option key held down during startup.  Windows 7 booted fine before I booted into MacOS.  When I tried to reboot in Windows 7, that's when I received the non-bootable error.  All looks fine on the Windows 7 volume.
    I'm working with a Macbook Pro Early 2008, 256 GB SSD, Windows 7 and the Boot Camp Support Software 4.0.4033.
    I tried to re-install Windows 7 on its 32 GB partition, however Windows reported volume is not in proper format???
    I tried repairing my Windows 7 volume with my install disk, but apparentl after having to update my initial Windows 7 instalation (disk bought in 2009) about 3 or 4 times, my Windows 7 install disk reports it cannot repair the now updated version of Windows 7 on my hard drive.  Lovely.  Brilliant engineering.
    I looked into editing my partition table, but that process appears more a hack/bandaid for the underlying problem that more than likely still exists.
    Any suggestions, other than painfully starting from the beginning???
    Thanks.

    Well, want to rule out drive case,, as those do come up with EVERY new OS, just hit Lion 10.7 forum when it came out, or when 10.6.0 came out 3 yrs ago.
    Maybe the power adapter is the weak link.
    As I said, and goes back yrs, not a fan of FW/USB/eSATA case from major vendors (LaCie, WD, Seagate etc).
    And you could try another case. Be sure to buy a case that lets you swap in your own hard drives though.
    http://www.macsales.com/firewire - look for bare drive case "0" capacity hard drive

  • Mac does not boot after installing bootcamp

    hello
    installed bootcamp on my mbp with snow leopard today,for the first time mac and windows both started with no problem ,but when i was trying to boot back into the mac again ,it did not boot and just got stuck at the process with turning wheel forever ,showing the apple logo and the turning wheel.
    i did try to hold the option button and chose the mac partition ,but again i can not pass thru the turning wheel and apple logo.Does anybody know what the problem is and how can i go beyond this .
    thanks.mike

    Csound1 wrote:
    Have you tried a safe mode boot yet?
    Reboot to the OSX partition and hold the shift key down as soon as you hear the chime. You can release the shift when you see the spinning gear wheel.
    yes,i did try that too.unfortunately ,hard drive seemed to be the source of the problem.just replaced the hard drive with a brand new one and put this one inside a usb enclosure that i have ,so tomorrow i will get a backup first and then format it again and keep it for the future.
    thanks.mike

  • Win 7 Bootcamp does not boot beyond windows splash screen.

    I am Running a Windows 7 bootcamp partition which has been running fine for months, untill today when it now just goes to a non responsive blank screen after the Windows splash screen.  I am able to boot the win7 os into safe mode successfully, and also have the bootcamp partition set up as a VM, which i am able to boot into successfully in normal mode. Very odd.
    I am running an 2.6GHz i7 Retina MBP with 8GB ram and a 512 SSD
    Any help/ideas would be appreciated
    Cheers
    O.

    Quote
    Originally posted by Syruel
    Thank you to everyone who helped me w/my prob.  I got an Antec True Power 430--they didn\\\\\\\'t have any of the 550\\\\\\\'s in stock--and now my system is up and running.
    Sadly, I still could NOT boot up the existing OS--I still had the same problems mentioned above--can anyone explain that?
    But, I was able to install the OS on a blank HD, which worked just fine for some reason--I just have to reinstall everything now--any ideas as to that?
    As for the manual and RAM...screw that...Quote
    also do you mean 3 gigs of ram total when you say 3x1gig if so your board only supports 2 gig of ram when it is pc2700...
    Yes, I mean 3 Gigs total.  I read on Soyo\\\\\\\'s website that it\\\\\\\'s MoBo\\\\\\\'s do that and will only support 3 Gigs at 2100, hence me underclocking my RAM at 266 Mhz.  It would have been really useful if MSI\\\\\\\'s documentation would have said the same thing.  3 Gigs at 2700 is the reason my system would NOT even POST.  Where did you see that it only supports 2 Gigs at 2700?[/COLOR]
    That's not unusual that you would have to do a fresh install of your OS to get it running properly. As far as RAM these boards are very sensitive to types of RAM so You may have trouble with your sticks. As far as 3 1 Gig sticks, unless you are doing some very heavy graphics it is probably overkill and you will find better performance with two sticks running in dual mode. Try it and see which way it runs better for you!
    Rob

  • Intel iMac will not boot past gray screen

    Intel iMac will not boot past gray screen
    my system:
    new (month old) 24" intel imac, 2.8 ghz, 4 gb ram.
    running: leopard (upgraded from tiger, which was pre-installed at purchase), installed 10.5.1 update right before this huge problem occurred.
    install discs on-hand: two-disc tiget set, single leopard upgrade disc.
    what led to this:
    i wanted to install windows using bootcamp on a 50 gb partition.
    at this point i was running leopard 10.5
    i followed all bootcamp instructions, printing out the guide, as well. once i got into the windows setup, i was prompted to choose a partition to install windows. unlike the bootcamp guide, which showed three partitions, one clearly labeled "bootcamp", i saw only one partition. not wanting to risk writing over my mac partition, i quit the setup and rebooted the mac os. after some googling around, i looked for firmware updates (didn't need any), and then software updates. i decided to try updating to 10.5.1.
    i then ran through boot camp again, deleting my previous windows partition, creating a new one, and moving forward as before. once again, i was only shown one partition to choose from in the windows setup. i exited the setup again to reboot through the mac os, but this time, i was only given a blank gray screen.
    here's what i have tried so far:
    booting from a CD, holding down the C or D keys: no response (in fact, i have to restart the computer holding down the mouse button to be able to eject the CD)
    booting with option key held down: gray screen
    booting with option key held down with external bootable firewire drive attached: the firewire drive appears as a boot icon, and i can click on it within a five second window, but then the screen freezes after that time period, and nothing changes
    booting into target mode while attached to another mac: gray screen (no firewire icon, and drive never shows up on other mac)
    resetting NVRAM: i'm able to hear the boot chimes, but no difference in performance. gray screen every time
    Safe boot: nothing but a gray screen
    Verbose mode: gray screen
    Single user mode: gray screen
    Single user mode with firewire drive attached: occasionally (not every time), i am able to get the white on black terminal to show up. from here, i'm able to run fsck, but it appears to only be checking the firewire drive. i have tried several times to boot from here, and once it took me to a blue screen with movable arrow cursor, but it never went beyond this.
    is there anything else left to try before taking it to apple?
    any help would be greatly appreciated.
    thanks,
    Casey Burns
    Casey Burns Illustration and Design
    http://CaseyBurns.com

    I'd call Apple support at this point. You'll need
    to put this issue on the record.
    Call U.S. iPod and Mac technical support: 1-800-APL-CARE (1-800-275-2273)
    The wait may be long for an agent to come on the line
    so expect that and have some other stuff to do in the meantime.
    If you have the applecare protection plan, I'd ask about "onsite"
    service.
    I like your work ! Good luck !
    Slim
    Message was edited by: slimpikkunz

  • HELP! How can i restore/recover files from Bootcamp with Boot Failure - Missing operating system error?

    Hi,
    I am having a few problems with bootcamp on my imac. When i tried to move the bootcamp partition on windows 7 into free space, it crashed and turned off. Ever since i have had the error 'Missing operating system' and it fails to boot. I have some very important files on the bootcamp partition. Is it possible to recover these files or even to restore the bootcamp partition to it's original state? I do not have a backup of my bootcamp partition. Another problem i have is that ever since i tried to expand my macintosh HD partition into free space, when i hold alt while booting up (to choose which partition to boot like i normally do), the bootcamp partition has stopped appearing. This means that i cannot even boot the windows 7 bootcamp partition anymore!
    So basically here are my 2 questions:
    How can i restore/recover files from Bootcamp with Boot Failure - Missing operating system error?
    How can i make the Bootcamp partition appear in Startup Disk and when i hold the option key while starting up my computer to allow me to boot windows 7?
    Any solutions are very much apreciated!
    Thanks!
    I know that bootcamp (disk0s4) hasn't been fully deleted since it appears in disk utility (i cant do anything to it though)
    And here is the error i see when i try to launch bootcamp (back when i was actually able to boot up bootcamp to the error screen)

    WinClone 3 is OS X and saves Windows image it makes for restore - that should work but you will have to try and you would need to make a new image unless it also works with a native Windows system restore image. It is now supported and has come a long way.
    http://www.twocanoes.com/
    Paragon Clone OS works and does disk-to-disk clone just like CCC you end up with two bootable drives. But does not work with your setup. It would let you clone and move your Windows install to an SSD or another disk drive though and be bootable.
    During its clone process it checks for errors which is very helpful and lets you know - something CCC and others should adopt more of.
    http://www.paragon-software.com/downloads/demo.html
    I wish for our/my sake you had re-read and rewritten the long 'story' and broken it into a brief list of facts we needed.
    OS X
    Windows
    Backup (though external is much safer) and you want bootable OS X clones as well as TimeMachine
    https://support.apple.com/kb/HT1427
    https://support.apple.com/kb/HT1553
    There are a number of things to do like chkdsk and others as well as Windows DVD to do automatic system repairs and find out why.
    AppleHFS - the abilty to mount and read HFS volumes can be notorious.
    I would rearrange and redo your storage setup and how you use the 4-5 internal hard drive bays.

  • Resized partition using Disk Utility and now Windows 7 will not boot

    Hi,
    Hopefully someone can help me!!
    I had previously used Boot Camp to install Windows 7. However, I later realised I had not given myself anywhere near enough disk space as I started using Windows for things I hadn't originally planned on using it for.
    Anyway, long story short, to solve the problem I uninstalled some applications on my Mac OSX and used Disk Utility to decrease the size of my Mac partition. My plan was then to reboot to Windows and use a Windows application to increase the size of the Windows partition. However - I coudln't even get that far.
    Upon decreasing the size of my Mac partition (succesfully) I restarted my Mac in order to boot to Windows. However, I was greeted with a message along the lines of "unable to boot to Windows please insert boot disk and press any key" (I can't remember the exact message).
    I was wondering if anyone knows of any way to restore my Windows partition, retaining all of my previously saved files on my Windows disk. It's probably a long shot, but the thought of losing everything I have been working on for the last few months is a sickening one.
    What does give me a bit of hope is that, if I click Boot Camp it seems to recognise that Windows 7 is installed as the option that appears is to uninstall it.
    Furthermore, if I view partitions in Disk Utility, a "DISK0S4" is listed. However, it's only at 20gb - if this WAS my BootCamp partition previously, it was originally at something around 60gb (I think - either way, definitely bigger than 20gb!).
    On top of this, my current Macintosh HD parition is at 260gb and with the DISK0S4 partition at 20.21gb, there seems to be some space missing... I'm hoping this is the files I've been working on over the last few months!
    Anyway, I've done some searching on the net and it *seems* that GPT fdisk *might* be my savour. I've downloaded it but have no idea how to use it and don't plan on playing about with it as I could no doubt do some real damage. If it is likely to solve my problem however, I'm certainly more than capable of being walked through what I need to do.
    Please help!

    Hi Christopher,
    I also have problems with Windows rebooting after partition resize trying to reduce Mac side and increase Windows side. I do not see the BootCamp partition labelled as such while running disk utility. The Windows partition shows up when I boot up while pressing the ALT key. However, when I try to run Windows, it says " error loading operatig system".
    I also followed instruction and went through to run gdisk successfully. Results towards the end.
    What can be done? Windows still does not boot and It shows ? Suspicious MBR at sector 0.
    Below is information based on typical questions you ask.
    diskutil list
    /dev/disk0   #:                       TYPE NAME                    SIZE        IDENTIFIER
       0:              GUID_partition_scheme                        *120.0 GB     disk0
       1:                                           EFI                         209.7 MB     disk0s1
       2:                         Apple_HFS Macintosh HD            78.5 GB     disk0s2
       3:                       Apple_Boot Recovery HD             650.0 MB     disk0s3
       4:                   Microsoft Basic Data                         31.7 GB      disk0s4  
    sudo gpt -r -vv show disk0
    gpt show: disk0: mediasize=120034123776; sectorsize=512; blocks=234441648
    gpt show: disk0: Suspicious MBR at sector 0
    gpt show: disk0: Pri GPT at sector 1
    gpt show: disk0: Sec GPT at sector 234441647
          start       size            index       contents
              0          1                             MBR
              1          1                             Pri GPT header
              2         32                            Pri GPT table
             34          6        
             40     409600           1            GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
         409640  153240016      2            GPT part - 48465300-0000-11AA-AA11-00306543ECAC
      153649656    1269544     3            GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
      154919200   17628896        
      172548096   61892608    4            GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
      234440704        911        
      234441615         32                       Sec GPT table
      234441647          1                        Sec GPT header
    sudo fdisk /dev/disk0
    Disk: /dev/disk0 geometry: 14593/255/63 [234441648 sectors]Signature: 0xAA55
             Starting       Ending
    #: id  cyl  hd sec -  cyl  hd sec [     start -       size]
    1: EE    0   0   2 - 1023 254  63 [         1 -  172548095] <Unknown ID>
    *2: 07 1023 254  63 - 1023 254  63 [ 172548096 -   61892608] HPFS/QNX/AUX
    3: 00    0   0   0 -    0   0   0 [         0 -          0] unused     
    4: 00    0   0   0 -    0   0   0 [         0 -          0] unused  
    sudo gdisk /dev/disk0
    GPT fdisk (gdisk) version 0.8.7
    Warning: Devices opened with shared lock will not have their
    partition table automatically reloaded!
    Partition table scan:
      MBR: hybrid
      BSD: not present
      APM: not present
      GPT: present
    Found valid GPT with hybrid MBR; using GPT.
    Command (? for help): r
    Recovery/transformation command (? for help): h
    WARNING! Hybrid MBRs are flaky and dangerous! If you decide not to use one,
    just hit the Enter key at the below prompt and your MBR partition table will
    be untouched.
    Type from one to three GPT partition numbers, separated by spaces, to be
    added to the hybrid MBR, in sequence: 4
    Place EFI GPT (0xEE) partition first in MBR (good for GRUB)? (Y/N): y
    Creating entry for GPT partition #4 (MBR partition #2)
    Enter an MBR hex code (default 07):
    Set the bootable flag? (Y/N): y
    Unused partition space(s) found. Use one to protect more partitions? (Y/N): n
    Recovery/transformation command (? for help): o
    Disk size is 234441648 sectors (111.8 GiB)
    MBR disk identifier: "DELETED INFO"
    MBR partitions:
    Number  Boot  Start Sector   End Sector   Status      Code
       1                               1    172548095   primary     0xEE
       2           *     172548096    234440703   primary     0x07
    Recovery/transformation command (? for help): w
    Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING
    PARTITIONS!!
    Do you want to proceed? (Y/N): y
    OK; writing new GUID partition table (GPT) to /dev/disk2.
    Warning: Devices opened with shared lock will not have their
    partition table automatically reloaded!
    Warning: The kernel may continue to use old or deleted partitions.
    You should reboot or remove the drive.
    The operation has completed successfully.

  • Macbook Pro Will Not Boot Windows Disk

    I have a late 08 (or early 09) Unibody Macbook Pro 2.53Ghz. I start the Bootcamp Assistant and successfully create my Windows partition. When I restart with the Windows 7 disk, I get a blinking cursor for 1 second then it goes to a black screen and never leaves. I have tried several different Windows 7 disks with the same result. I have even tried booting from a Windows Vista, Windows XP and even a Ubuntu disk all with the same result, stuck at a black screen.
    I took the hard drive out of this mac and put it into my wife's older Macbook pro, and it booted off the Windows 7 disk and completed the install to the drive with no issues. I then put the hard drive back into my Macbook Pro and get the same black screen when trying to start the Windows partition, and still have the same problem that it will not boot from any other OS disk be it Windows or Ubuntu. It boots from OS X DVDs without a problem.
    Also several months ago I had a Windows XP installation on this computer with no issues. I wiped it just before going to Snow Leopard.
    Any clue as to what is going on here?

    What is really odd is if I take my hard drive out of my Unibody Macbook Pro and put it into my wife's non-unibody Macbook Pro, it boots the Windows partition with no problem (Remembering I previously swapped these hard drives to complete the Windows installation to my hard drive). Seeing as the disk boots on her machine fine and not in mine, and my Windows cds (DVDs) boot fine on hers and not on mine, it seems to me it's something specific about my machine, but I can't imagine what it is.

  • Can not boot into OSX after boot camp installation and resizing of Macintosh HD

    So from the beginning what I was trying to do was set up my iMac (27-inch, Late 2013)  with boot camp so that I could play some old windows based games that can not be played in Parallels.
    I went through the Boot camp process and everything set up just fine.
    I had both OS X Yosemite 10.10.2 and Windows 8 Professional running but as I was installing games on to boot camp I discovered I did not allocate enough space and needed to extend the Boot Camp partition.
    I used boot camp utility to set OS X as the default start up disk and had it restart
    I launched into OS X and used Disk Utility to shrink Macintosh HD another 120GB
    Restarted again holding option and launched into Windows
    Used the disk management in windows to try and extend the boot camp partition into the unallocated space.
    It was not an option to extend it so I tried to create a new simple volume from the unallocated space then delete it and try to extend it again.
    It still was not an option.
    From there I went to restart again while holding option and the only options I had were 10.10 Recovery and Windows
    I tried using disk utility in recovery and Macintosh hd now only showed disk0s2
    I tried to verify and it could not verify
    I tried to repair and it could not repair.
    I put the iMac in target disk mode and using a thunderbolt cable I tried using disk utility from my MacBook Pro (13-inch Mid 2012)
    Verifying volume “disk2s2”Verifying file system.** /dev/rdisk2s2
    Invalid BS_jmpBoot in boot block: 000000
    File system check exit code is 8.Error: This disk needs to be repaired. Click Repair Disk.
    Verify and Repair volume “disk2s2”Repairing file system.** /dev/rdisk2s2
    Invalid BS_jmpBoot in boot block: 000000
    File system check exit code is 8.Updating boot support partitions for the volume as required.Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
    This is the same error I got on my iMac
    I used terminal diskutil list and got:
    /dev/disk2
       #:                       TYPE NAME                    SIZE       IDENTIFIER
       0:      GUID_partition_scheme                        *1.0 TB     disk2
       1:                        EFI EFI                     209.7 MB   disk2s1
       2:       Microsoft Basic Data                         799.3 GB   disk2s2
       3:                  Apple_HFS Recovery HD             650.0 MB   disk2s3
       4:       Microsoft Basic Data BOOTCAMP                70.3 GB    disk2s4
    I can see that Macintosh HD was disk2s2 but it now shows its Microsoft Basic Data.
    I did not format this partition and it was working fine till I restarted the computer after resizing Macintosh HD.
    I am not sure what I can do to fix this.
    I've found multiple articles about similar issues, but the issue thet they have was that they could not boot to Windows instead of my issue not booting to OS X

    ****************    Update    *****************
    From the Windows Partition using Disk Management I can see that the drive is still labeled Macintosh HD and that all of my data is there.
    I have a complete backup so i'm not worried so much about the data.
    What I'm most interested in is trying to solve this issue because I'd like to continue using boot camp and I actually work with mac computers and would like to be able to help others if this issue arrises again.

  • Intel IMac will not boot OSX Tiger

    Hi guys, I just wanted to let you know that I am reading and trying to do my home work on why my Intel I-Mac will not boot. It all started after running Windows Vista using Apple Boot Camp. I just wanted to list a few things I have tried after getting replies from posting in some other forums. I will try here since a few people are having similar issues. Any tips would be appreciated. Please no flames
    1. If I hold the C button while booting to boot from CD-ROM I get a panic alert.(panic alert meaning lockup, I have to restart or press and hold power button)
    2. Holding down D button upon startup will run Apple Hardware test just fine, but no errors found.
    3. I can press Option-Command-P-R to reset NVRAM successfully.
    4. I can press Option during startup to start the Startup Manager. I can see my Macintosh Hard Drive and CD-ROM, but get a panic alert if I click on either icon. I’m not sure what happened with the Windows Vista hard drive Icon.
    5. I can press N during startup to start up from a compatible network server. I see a flashing globe and then a panic alert. Not sure what this function is for.
    6. If I press T during startup for Start up in FireWire Target Disk mode, I get a weird symbol that looks like a Y floating around the screen. I have no idea what target disk mode means.
    7. If I press Shift during startup to boot in Safe Boot mode, I get a panic alert.
    8. If I press Command V during startup for Verbose mode, it appears that I am at a Unix style Command Prompt that hangs.
    9. If I press Command S during startup for Single-User mode, I am at the Unix Command prompt which works, but I do not know any commands except fsck –fy which I guess is like a DOS CHKDSK command that tells me my Volume appears OK.
    10. Pressing Option-N during startup to start from a NetBoot server using the default boot image gives me the flashing globe icon again, and then hangs.
    11. I tried resetting the System Management Unit thanks to the Unix forum guys, but still have the same problems.
    12. My next step is to find a Mac friend to burn the Firmware Restoration CD file I downloaded thanks to Michael from the Unix forum. If that does not work I will try whatever you ask.
    13. I can boot my I-Mac using a Linux Live CD called Slax and surf the net and play with the software. It runs just great; I just don’t think this 200MB version has the capabilities to format the hard drive or Install to hard disk like Fedora Live does. By the way, the Fedora Live version of Linux hangs after booting from the CD. It boots just fine on my PC.

    Greetings,
    Somehow or other you will need to be able to boot to the Installation Disk #1 that came with your computer - as you know they are specific to each machine model. After a successful boot to that disk, you can use Disk Utility to remove all of the partitions, wipe that puppy clean, then repartition and make sure you use the GUID partition scheme - you really only need the Bootcamp Assistant if you have multiple drives, internally, and since you have an iMac, your good to go.
    When you booted to your Linux disk, could you see the internal hard disk? If so you should be able to open one or two of the folders just to be sure that the disk is OK.
    A worst case scenario would be to have to install a fresh hard drive. Do you have any way of borrowing another install DVD for that model to try to get it to boot? That's the key to this whole project.
    Try this - Go back into single user mode and issue these two commands in this order:
    /sbin/fsck -fy
    /sbin/mount -uw /
    Watch the spaces and then issue a "reboot" at the prompt.
    During this, the fans will likely come on at a high speed and may stay on for a while and maybe until you do a shutdown and reboot.
    I hope this helps a little, and once you get the machine booting to the Installation Disk #1, again, you'll be all set.
    You don't say, but is this unit under warranty - I know it may be a stupid question on my part, but if it is, give them (Apple) a call and get some advice on the waranty actions.
    Good Luck my friend.
    Cheers,
    M.

  • The system will not boot

    Hello, I am trying to install windovws after the restart can not install Yosemite because can`t please format the hard disk.Please help because just yesterday bought macbooc

    FYI...the top partition is too full. You need free space. You will need to remove the bottom partition then make the top partition larger. Make sure you have 10% or more free space. If you use Parallels or VMware you don't have to partition your drive. If you use the vm software you can run Windows wihtout having to reboot into bootcamp each time you want to use it.
    See this link for help after you resize your top partition.
    https://www.apple.com/support/bootcamp/
    I forgot to ask...
    If the system will not boot, how are you seeing Disk Utility. Are you booted from the Recovery Drive? If yes, then you will need to erase the internal drive and reinstall Yosemite on the internal. When you erase, make it one partition. You can add a second partition later that's smaller.
    Note: you posted in the OS X 7 Lion instead of the Yosemite forum. In the future, asking on the correct forum gets the best answers.
    Parallels   http://www.parallels.com/
    VMware Fusion   http://www.vmware.com/products/fusion/

  • Macbook Pro will not boot from USB drive or Macintosh HD

    The Mac in question:
    Macbook Pro mid-2009
    2.4GHz Core 2 Duo
    4GBs RAM
    OSX 10.8.4
    Basically I did a fresh install of OSX 10.8.4 and Installed Windows 7 Home Premium 64bit via Bootcamp.
    All software was up to date, I had the newest version of bootcamp for windows software, and everything was working fine.
    I lent the computer to my dad
    fast forward 3 months.
    Windows boots fine and works for about 15 minutes then Blue Screens and restarts. Endless loop.
    I did everything conveiveably possible for the Windows side before deciding to work on the Apple side.
    Come to find out, my dad had not booted into the Apple side for almost 3 months. So on holding option and selecting the Macintosh HD icon, I got the apple logo with a spinning wheel under it. The wheel spun for about a minute then stuck. No response, so I held the power button down and restarted.
    held option, and selected "Recovery 10.8.4" same deal minus the spinning wheel. stuck on the apple logo.
    so i plugged in my bootable mountain lion usb (has been used countless times and works, its not the usb) and selected the usb. Same stuck apple logo.
    I am at a loss as to what to do now. I dont care about any information on the drive, so i dont mind formatting and such.
    But i am at a loss as to how to repair it if i cant access and bootables to do a disk repair or a clean install
    Any suggestions would be helpful, thanks.
    (btw, ive reset SMC and PRAM and all the usuals and ive internet searched out the whazoo, so yall are my last resort *grin*)
    -Dusty

    New info:
    Selected Recovery disk in boot options menu and it loaded.
    Disk recovery disk verification says there are errors with Macintosh HD but it cannot repair them.
    Tried Reinstalling mountain lion from the Recovery screen and followed the instructions, signed into my Apple ID and it started installing mountain lion on Macintosh HD.
    It immediately said 4 hours to complete and the blue progress bar started moving slowly.
    it says it is "Downloading additional components, your computer will restart automatically"
    about an hour later i checked it and the bar was full, but the estimated time was 1 hour 59 minutes and it has been almost 12 hours now.
    Just trying to give a play by play so yall have something to work with.
    making a Mountain Lion bootable USB as i type, will try that as soon as its done.
    Dusty

  • Imac 21" mid 2011 can not boot from USB device?

    Hi,
    hope someone can help me.
    Bought the new imac 21" and replaced the superdrive with a ssd drive.
    Works great but it seems that the imac is not able to boot from any usb device.
    I put my osx install disk in my external dvd drive and powered my mac.
    While booting up (pressing cmd) the mac does not recognize my external dvd drive. This works great with my MBP late 2008. But the imac can not boot from the dvd drive. Also pressing "c" while booting does not work. Doing that a grey screen appears and after some time mac boots from hdd.
    So i installed mac os via target mode over firewire withbmy old imac. This works.
    But now i want to install windows on a bootcamp partition.
    I can't boot from the windows 7 professional dvd, too. So i tried to create a bootable win 7 thumbdrive. Mac can't boot from this too. Reading many threads in some forum i tried with rEEfit. Reefit shows the usb thumbdrive whike booting, but using this will end in a black screen error from bios: "no bootable device....". Tried a knoppix on the usb thukbdrive, too.... No bootable device....
    It seems that there is no way to boot from ANY external usb device like dvd drives or thumbdrives......
    What more can i do? I tried for 2 evenings now, but nothing worked out for me......
    Currently i don't see any any to install win 7 without an internal superdrive, but can this be??
    Thanks for any comments.
    Kwicks

    Internal is definitely the easiest but you can boot from external HD or external optical drive, the mac is just very picky on what works and what doesn't.
    For an external drive or usb stick it has to be GUID partition table and have 10.4.5 or better installed on it, for more info check this link out ( http://support.apple.com/kb/ht1948 )
    Hope this helps,
    Joe

Maybe you are looking for