Booting Windows on Intel Mac from an external Firewire/USB hard disk?

Is it possible to boot an Intel iMac from an external hard disk - in target disk mode etc., without having to install Boot Camp?
I have a spare drive with installed XP on it and I need to find out what is on the drive before re-formatting. However, I only have my mac in which to do so. The extra disk will be used in an external firewire/USB 2.0 caddy. I have researched some methods, but they are all very long winded and require a PC or the creation of a Windows partition on my start-up disk using Boot Camp.

"Is it possible to boot an Intel iMac from an external hard disk - in target disk mode etc., without having to install Boot Camp?"
No.

Similar Messages

  • External Firewire 800 hard disk kills internet connection

    Hi,
    I am having the following problem:
    1. Plug Seagate FreeAgent GoFlex 1TB drive into Macbook Pro via Firewire 800
    2. Internet connection dies.  By "dies", I mean I disconnect from the wifi network.  The degree of death varies from complete lack of visibility of the wifi network, to visibility but cannot connect ("connection timeout" when entering the password (which I should not have to enter anyway, as it's cached in my keychain)), to connection but no IP address given by the router via DHCP, to sometimes getting an IP but being unable to ping any other IP address on the network apart from my own.
    3. Ejecting then disconnecting the drive physically, fixes the problem.
    4. Connecting the drive via USB instead of FW800, does not reproduce the problem.
    5. Connecting any my 500GB Lacie rugged drive via FW800 does not produce the problem.
    Like the guy in this discussion (http://discussions.apple.com/message/15615649#15615649), this is only happening with my Seagate FreeAgent GoFlex 1TB drive and only when I connect it via Firewire800.  With any other drive, OR if I connect the Seagate via USB, all is OK.  Note that I'm re-posting this discussion because that other guy accidentally marked the problem as "fixed", but it was never solved.

    When the firewire card is not connected, I get the following screen in system profiler:
    FireWire Bus: powerbook's built-in FireWire bus
    Maximum Speed: Up to 800 Mb/sec
    OXFORD IDE Device 1:
    Manufacturer: OWC Mercury Elite Pro AL
    Model: 0x0
    GUID: 0x1D2020092025F
    Maximum Speed: Up to 800 Mb/sec
    Connection Speed: Up to 800 Mb/sec
    Sub-units:
    OXFORD IDE Device 1 Unit:
    Unit Software Version: 0x10483
    Unit Spec ID: 0x609E
    Firmware Revision: 0x102
    Product Revision Level: 3.AA
    Sub-units:
    OXFORD IDE Device 1 SBP-LUN:
    Capacity: 232.89 GB
    Removable Media: Yes
    BSD Name: disk1
    OS9 Drivers: Yes
    S.M.A.R.T. status: Not Supported
    Volumes:
    250 Gb:
    Capacity: 232.76 GB
    Available: 203 GB
    Writable: Yes
    File System: HFS+
    BSD Name: disk1s10
    Mount Point: /Volumes/250 Gb
    Notice that the connection speed of the hard disk is 400Mb/s in the first, and 800Mb/s in the second.
    The reason I'm fussing about this is because I'm using the hard drive with Pro tools, which officially supports Firewire 800 hard disks with the Oxford 912 chipset (which is what this one's got). And I've had a lot of problems bouncing to disk, even with just a stereo mix (96KHz 24 bit) Where Pro Tools (M-Powered) says that it can't read data from the hard disk fast enough!
    I just want the hard disk to run at 800Mb/s and the audio interface to run at 400. Am I asking too much?
    Someone must know how to do it.
    Thanks for your help!

  • Is it possible to boot a G4 (pci graphics) from an external firewire drive?

    I have a Lacie 250 gig bootable external firewire drive which is recognized on my Power PC G4 400 but I cannot get it to boot from this drive. The procedure works fine on my ibook... I looked into a possible firmware update but the apple site says no update is necessary for the G4 400/pci graphics...
    Any suggestions?

    There sure are some radically contradictory posts here! (This isn't typical, at least in this section of the Discussions, RMx2.)
    Can anyone who has posted here (or might join in here) actually boot from a hard drive connected via USB? I just tested this with OS X and I can't. For some time now, the Discussions have been riddled with posts, whether 100% accurate or inaccurate, that Macs don't boot from USB drives, despite the seemingly conflicting info in the article that Don kindly referenced. (John Huber: Don't eat your words just yet, John!)
    Here's my personal experience, for what it's worth... I have a rev.2 B&W G3 which recognizes, reads, and writes to drives via USB, but refuses to boot from them (I tested with OS X 10.3 and 10.4). I also have a QS 2002 G4 that yields the same results. The QS G4 will, however, boot from these drives via FW. I used a WiebeTech ComboDock for testing this with both USB and FW. I tested with two different hard drives, both of which are known to have stable, working versions of OS X on them.
    My G3 running OS X 10.3.9 sees the USB-connected drives in the Startup Disk Preference Pane, but when I click to Restart after selecting the USB system folder there, I get a beachball (haven't seen that in awhile...) and have to Force Quit System Preferences. Console tells me that that it could not get open firmware information or set open firmware information, and that it can't touch or set System/Library/CoreServices/BootX, returning Error 1 running bless.
    On the QS running Tiger, the USB OSs don't even appear in the Startup Disk Pane of Sys Prefs. I can see the USB drive(s) using the Startup Manager, but selecting them and restarting results in a hung startup to a spinning cog with a prohibitory sign on the screen...
    I haven't tried playing around with open firmware NVRAM settings (and don't intend to, except perhaps for trying an NVRAM reset), nor have I attempted to boot to OS 9, reset the startup disk there, and attempt the boot again to the USB device in OS X and in OS 9, which I may try later on when I have a bit of time...
    Gary
    Message was edited by: Majordadusma

  • Can you boot / run an Intel iMac from an external hard drive? Built-in drive is dead.

    Hello, Have a six? year old, 2.16 GHz Core 2 Duo iMac that has a dead internal HD. The drive has 16,000 hours on it (per SMART Utility) and no longer shows up on desktop. Disk Utility, Disk Warrior and SMART say it's toast. I'm backed up to Flash drives and Time Machine but need a month before I can get a new computer... Don't want to run this one off TM back-up. Question is, can I add an external drive, use TM to make it my start up drive until then... Thanks, dp

    Yes you can, you're going to install OSX on it (from the Snow Leopard disk) but it will work.

  • Booting the Mac from an external USB drive

    I was under the impression that you could only boot a Mac from an external firewire drive. However, I have just successfully booted my new MacBook from an external SuperDuper backup connected via USB.

    I was under the impression that you could only boot a Mac from an external firewire drive.
    That basically only applies to Mac OS X on PowerPC Macs, not on an Intel Mac such as a MacBook.
    (37425)

  • Booting two Macs from one external drive: 10.8 and App Store?

    I boot two Macs from one external harddrive. Does this mean that when 10.8 is sold exclusively via the App Store and thereby linked to a unique hardware identifier, I am going to have issues with activation/authentification each time I switch machines? I have avoided the App Store since I discovered that an app I bought there, and which I really needed to open automatically on log-in, had to be manually re-activated with my Apple ID after every switch (so that I eventually deleted it and reverted to an earlier, non-App Store version).

    Welcome to the forum!
      There are a couple of "solutions" to your problem.  The easiest, and possibly the best for you (although it is a bit slower) is to copy your catalog onto the external drive as well.
    Then when you plug in the drive, you will always have your latest catalog for access.
    The other way is to keep a local copy of your catalog, and copy it onto the local drive as a way to transfer it from one computer to the other.
    This has the problem of possibly not being in sync, that is, you forgot to copy it over once and did some editing.  Then you would end up with essentually two different catalogs, instead of one in two places.
      You can copy the catalog either with your OS, or you can "export as catalog" and specify the external drive as the destination.  Then, on your other computer, "import from catalog" and only take the meta-data settings (it's on the import dialog box).
    Personally, when I'm traveling, I have my catalog on my external drive as well.  It just makes life easier, and I don't have to worry about it being out of sync, or losing it (and not the images).
    So, I would go with the first method, at least to start.  To get your catalog over there, you can either export as catalog or copy it, either one will work.
    You can find the location of your catalog file (if you don't know where it is) in the catalog settings menu prompt.  Both the location and the name will be displayed.
    Cheers!

  • Booting os x from *partitioned* external firewire drive?

    Hi all,
    my internal hard disk (on a 12" powerbook G4 867 mhz running osx tiger 10.4.10) has started acting weird (many people are reporting failing hard drives, and I'm assuming mine is failing too), so I'm preparing for replacing it with a new hard drive.
    I've backed up the drive to an external firewire drive (LaCie portable 80 GB firewire drive "Design by F.A. Porsche") using Carbon Copy Cloner with the option 'make bootable' selected.
    PROBLEM: I can't boot OS X using my clone on the external drive.
    I'VE TRIED:
    1. holding down Command-Option-Shift-Delete while booting to bypass the internal drive. (This didn't work: I saw an os 9 icon blinking/alternating with a question mark for a while, and then the computer booted from the internal hard disk.)
    2. holding down Option to select the external drive in Startup Manager. (Didn't work either: Startup Manager opened fine, but only showed my internal drive volume. I tried clicking the 'rescan' button, but it couldn't find my external drive.)
    3. SELECTING THE EXTERNAL DRIVE under Startup Disk in System Preferences. Note that the external drive volume *did show up* there. So under some conditions at least, the external volume is identified as a bootable volume. (This didn't work either, though: When I shut down the computer and booted up with the external drive connected, it still booted up from the internal drive.)
    POSSIBLE EXPLANATION?
    My external drive is partitioned into three partitions of different formats:
    1. "Mac OS X Extended (Journaled)"
    2. "Mac OS X Extended (Journaled)"
    3. "MS-DOS File System (FAT32)"
    The bootable volume is the first partition with the os x format.
    Could my problem be caused by this partitioning of my external drive?
    Either way, what to do?? I hope some of you savvy people out there can help me out.
    Cheers,
    Philip

    Hi Philip,
    My problem has been fixed, & I imagine it's the same for you...:
    With the excellent help from Dave Nanian at shirtpocket.com - the developer of 'SuperDuper!' (thanks Dave - you rock!), the problem (as Michael suggested) is to do with the Partition Scheme of the drive.
    If your drive was like my portable LaCie Porsche drive, it was FAT32-formatted for PC out of the box. This format has an underlying MBR (master boot record) partition-scheme. When re-partitioning a drive in 'Disk Utility', the original partition-scheme sticks, so if you simply re-partition the drive to Mac OS Extended, it will still have an MBR partition scheme... which Macs cannot boot from!
    For a Power PC Mac to be able to boot from an external firewire drive, the drive MUST have an APM (Apple Partition Map) Partition Scheme underlying the Mac OS Extended partitions. To do this, click on the 'Options' button in 'Disk Utility' when on the 'Partition' page before partitioning. You will see the options:
    GUID Partition Table (for Intel Macs... (n.b. Power PC's cannot boot from a GPT drive))
    Apple Partition Map (to create a bootable drive for a Power PC Mac)
    Master Boot Record (to create a bootable PC drive)
    So.... to make your external drive bootable for your Powerbook G4, choose 'Apple Partition Map' in the 'Options' page prior to partitioning.
    Special note about Intel Macs: Contrary to info supplied by Apple, an Intel Mac CAN boot from an APM-partitioned drive (this is why the OSX installer can be univerally bootable!), BUT, the problem is that the OSX installer will NOT let you install OSX-intel on an APM-partitioned drive....
    You can, however, clone an Intel-Mac-OSX internal drive that has a GPT partition-scheme (using CCC or SuperDuper) to an external drive with APM, & the Intel Mac will still be able to boot from that clone...
    The only real use for doing this, though, is if you want a multi-partitioned backup drive with separate bootable partitions for OSX-PPC & OSX-Intel machines. (Remember that a PPC machine cannot boot from a GTP-partion-scheme drive, hence the need to use APM in this instance seeing as the Partition Scheme applies to the entire drive (it can't be different for each partition.)
    Good luck - let us know how you get on!
    Jason

  • The finder window for an external USB hard disk suddenly started separating files by time (today, yesterday, etc.) and stopped allowing me to change column width, order, etc. Also the header bar shifted to flat white from gray.

    The finder window for an external USB hard disk suddenly started separating files by time (today, yesterday, etc.) and stopped allowing me to change column width, order, etc. Also the header bar shifted to flat white from gray.
    All was normal until the icon for the disk stopped showing up on the desktop when I would plug it in. I rebooted the computer, and the disk icon now shows up but this new look to the finder window started as a result. The hard disk does not have this problem when I use it on another Mac running Snow leopard. Also, two other external hard disks that I use on this computer running lion 7.4 still have the normal header bars with columns that can be reordered, etc.
    I have tried looking in preferences and other places but have not seen this discussed. 

    Well duh - I finally figured out that somehow in the View options for the hard drive, the "arrange by" option had been changed to "by date" from "none". Not sure how that happened, I had never used the "view options" menu tem before. Changing "arrange by" back to "none" gets the gray column headers and the collapsible folder icons back. 

  • After clean install of Snow Leopard, Time Machine did not restore all files.  When I try to restore these files I get "Not enough disk space" error.  What do I need to do to get these important files back onto my Mac from my external hard drive??

    After clean install of Snow Leopard, Time Machine did not restore all files.  When I try to restore these files I get "Not enough disk space" error.  What do I need to do to get these important files back onto my Mac from my external hard drive?? 

    Janet.b wrote:
    About 3 years old...pretty dated now I guess.  Am thinking I may just need to have it upgraded by a Mac tech.
    For what the Apple Store's charge you can buy almost buy a new computer.
    Just for giggles I brought my old laptop in for a drive upgrade and asked, they wanted $600 for a drive that only cost $120 at the time and it was a slow 5,400 RPM drive. The new Mac's of a similar make were going for $1000.
    I did the drive replacement myself, got a faster drive of better quality for $300 instead.
    Then another time I asked for a RAM upgrade from 4GB to 8GB, they wanted to charge $400 + $35 for the labor.
    The same RAM is on Crucial.com for $90 and all I need is a 00 micro phillips screwdriver.
    So you see what's going on here.
    I think what you should do, if your out of warranty/AppleCare, is to call up the local PC tech guy who also does Mac's and have them fix you right up.
    They can offer more personalized care which you need. Clone your old drive to the new and everything.
    With Apple they are overworked at the Genius Bar and just place roadblocks so you buy a new machine instead.
    For instance, all new iMac's now have proprietary drive software installed on the hard drives for heat monitoring. So now the only choice a user has is to bring their iMac into a Apple Store for a very expensive drive upgrade, which a person then decides the money is better spent buying a new machine.

  • How to boot Linux USB Hard Disk from Windows Machine?

    *Dears,,*
    I have XP windows Machine . . .
    My laptop is Qosmio F20 155
    I need to boot Linux USB Hard Disk .
    I tried to enter setup menu to arrange the boot perority to make The USB Hard Disk FIRST but i cannot enter setup menu
    Please, help me ASAP
    *Many Thanks & Regards,,*
    Message was edited by: eng_mohammedmostafa

    *Dear,,*
    FYI , , ,
    We have another laptop (VAIO) and we can enter BIOS and edit the priority boot and it run successfully . . .
    But in laptop (Toshiba) We can't make it.
    *Thanks & Regards,,*
    *Eng Mohammed Mostafa*

  • Trouble with installing 10.5 from an external firewire drive

    I have a family pack of 10.5 and installed it just fine on my macbook. But, I'm having trouble getting my imac DVD player to read the DVD. It just spins and spits it out, and spins and spits it out. The imac is not covered under applecare so spending money to get the DVD drive fixed (which I barely use) is not something I want to do right now.
    Anyway, I followed instructions on a this website to install 10.5 from an external firewire drive. (http://iuseapple.com/blog/apple-how-to/advanced-os-x/2007/10/29/how-to-install-l eopard-from-external-firewire-hard-drive/)
    But I get stuck and am not able to actually get my imac to boot from the installer. Basically, I am able to use disk utility to create a copy of the disk image on my macbook. That resulting file ends in ".cdr" and it mounts when I double click it.
    And I partitioned my firewire hard drive without problems.
    I think I'm messing up when it comes to doing the restore. If I try to drag the .dmg mounted file in to the "source" it doesn't work (is greyed out). If I try to drag the mounted .dmg there than it works, but I get an error when I click "restore" (something about scans and images not being found). I tried physically copying the .dmg file onto the partition, but then when I plugged the HD into my imac, I wasn't able to get the imac to boot from the installer.
    What am I doing wrong? If someone could walk me through these last steps I'd appreciate it!

    Okay I finally got around to creating the bootable disk image of 10.5 using Carbon Copy Cloner. Still my iMac is not booting from the firewire drive!
    Here's a recap of everything I've tried. I'm at a complete loss now!
    - I partitioned the HD into 2 partitions-- a 10gig one for the 10.5 install, the then the rest for Time Machine. I make the partition in Disk Utility on my MacBook.
    - I've partitioned the drive a few times-- always partitioning it in APM format (b/c it needs to boot my non-intel iMac).
    - I've created the disk image using "restore" in disk utility. I've again tried this a few times.
    - I am able to boot my MacBook from the disk image I create! So I know the FW drive is able to be used to boot from!
    - Here's what I've tried in terms of getting the iMac to boot from the FW drive. It always just boots to my internal drive instead. Sometimes I briefly see a folder and question mark. I've tried all 3 FW ports. I've selected the install partition at start up in preferences. I've also held down the option key at start up (only my internal drive shows) and I've held down command-option-shift-delete and again I get the question mark and it boots to my internal drive.
    - And I installed Carbon Copy Cloner and made the disk image that way on my macbook. Still, I tried everything and the iMac is not able to boot from the firewire drive!
    Since my DVD drive is broken, this is the only way for me to install 10.5! Help!

  • Arch: Install to & run from External USB Hard Disk Drive (HDD)

    I wanted to play with ArchLinux 2009.02, but replacing the existing Debian-Lenny on the laptop's HDD wasn't an option. So I experimented with installing Arch on an external USB Hard Disk Drive.
    I have tried to make this "newbie-friendly", so I hope the more experienced will forgive the detail.
    Materials:
    Three year old Dell Inspiron 6000
         CPU = 2.0 GHz Pentium
         RAM = 2.0 GB
         Internal HDD = 80 GB
         Internal CD/DVD R/RW
    External USB HDD = Freecom FHD-2 Pro 80 GB
    Archlinux 2009.02 install CD
    Steps to install:
    1. I put the Archlinux install CD in the drive and connected the external 80 GB HDD in the USB port.
    2. When the Dell laptop was booted, I pressed F2 to enter the BIOS setup. I edited the boot sequence to the following:
         Internal CD/DVD
         External USB device
         Internal HDD
    On the Dell, you can also press F12 to select the preferred boot device for that boot.
    3. I started the laptop and the Archlinux installation menu came up and I proceeded with installation following the "Official Arch Linux Install Guide" and the "Beginners Guide".
    4. Used km to change to UK keyboard layout and then began the installer script (/arch/setup). I was installing from the core CD so I skipped the network steps.
    5. HDD preparation.
    This was fairly straightforward with two cautions:
         (a) Make very sure that the external HDD (sdb) is selected for the operations.
         (b) Remember to set the Bootable Flag for the first (/) partition on the HDD.
    I chose 20 GB for /, 2 GB for swap and the remainder for /home.
    6. The package selection and installation was fairly straightforward.
    7. Configuration of System
    This was section was straightforward with one warning:
         USB had to be added to the HOOKS in the /etc/mkinitcpio.conf file!
    I found this to be essential for my external USB HDD to function as a bootable device. Otherwise I got the same sorts of errors relating to unrecognisable file system types that other people have reported in the forum.
    The relevant line from the end of the edited /etc/mkinitcpio.conf file is below:
    HOOKS="base udev autodetect pata scsi sata usb filesystems"
    8. Installation of GRUB was the other point where caution and/or correction was necessary.
    When it asked where GRUB should be installed, I had to select sdb (my external USB HDD) and not any of the particular partitions on sdb. If the root partition sdb1 was selected then the laptop won't boot from the external USB HDD.
    The GRUB /boot/grub/menu.lst as written by the installation routine specifies hd(1,0) which doesn't work when you try to reboot from the external USB HDD. When you boot Arch from the external USB HDD, as far as Arch is concerned - at that point in time - the external USB HDD is the first drive in the system. To fix this:
         (a) When the Arch boot menu comes up, press e to edit the grub entries.
         (b) Change the first line to hd(0,0)
         (c) To the end of the kernel line add rootdelay=8
         (d) Press b to boot the system with these temporary corrections.
         (e) Once your Arch system has booted, edit the /boot/grub/menu.lst to make the above changes permanent.
    The relevant portion of my /boot/grub/menu.lst looks like the following:
    # (0) Arch Linux
    title  Arch Linux
    root   (hd0,0)
    kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
    initrd /boot/kernel26.img
    # (1) Arch Linux
    title  Arch Linux Fallback
    root   (hd0,0)
    kernel /boot/vmlinuz26 root=/dev/disk/by-uuid/... ro rootdelay=8
    initrd /boot/kernel26-fallback.img
    9. The laptop happily and consistently boots Arch Linux from the external USB HDD when it's plugged in before startup/booting.
    Running Arch from the external USB HDD seems as quick as running Debian from the internal HDD.
    So if there is a performance penalty associated with using an external USB HDD, my wife and I haven't noticed.
    In summary, the three essential points to address during installation to an external USB HDD are:
         Remember to set the bootable flag for the first partition.
         Add USB to the HOOKS for /etc/mkinitcpio.conf file.
         Correct the /etc/grub/menu.lst file.
    I hope this is helpful.
    Ted

    Hi Rookie,
    As you say, it is worth remembering the rootfstype= option for the kernel line just in case someone still has problems with GRUB after making all the other changes.
    I was working with the most recent Arch 2009.2 release.
    I only got messages about unrecognisable file system type when I tried booting with the "stock" or "as-installed" GRUB (before I edited /boot/grub/menu.lst). After editing /boot/grub/menu.lst to identify the drive correctly and add rootdelay, GRUB was able to do the rest and everything worked OK without any error messages.
    Best wishes,
    Ted

  • I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

    Do it with a Firewire cable (buy a 800/400 adapter if you need it) - the USB transfer takes a much longer time.
    Start up your old PowerMac G4 holding down the "T" key, for target disk mode.
    On your new MacBook Pro open "Migration Assistant" in your utilities folder.
    Connect the 2 computers by firewire cable and follow the prompts in Migration Assistant.

  • HT4889 Migration Assistant to update my new Mountain Lion iMac from an external USB hard disk drive, it is constantly saying that it is "looking for other computers". It doesn't find the external drive. Why is it looking for other computers?

    I'm trying to use Migration Assistant to update my new Mountain Lion iMac from an external USB hard disk drive. I told it to look for a drive, yet it is constantly saying that it is "looking for other computers". It doesn't find the external drive ... it just endlessly looks for other computers. Why is it looking for other computers at all, when I told it not to?

    Wow, the wording in Migration Assistant is misleading. I've never used it before, so I thought I would try to copy my files from the external drive ... my old iMac died, but I managed to get everything I need off it, using the 'cp' command in single-user mode. So I guess I'll just have to manually copy the files from the external drive to the new machine. I was hoping that Migration Assistant might help somehow, but obviously not.
    Thanks for the quick reply!

  • Will I notice a significant performance drop if I run my Imac 8,1(early 2008) direct from an external firewire 800 Harddrive

    Will I notice a significant performance drop if I run my Imac 8,1(early 2008) direct from an external firewire 800 Harddrive

    I notice quite a difference in two of my externals because of that (the 5400 rpm drive was a warranty replacement and I had no idea it wouldn't be 7200 rpm - but that's another subject.....).

Maybe you are looking for