Bought a Netgear wnr2000v3 wireless router and set it up but could not get an internet connection.

After setting up the Netgear wnr2000v3 router and powering, indicator lights, on the router, are supposed to be green to indicate power is on and router is connected to dsl through to modem. The lights are not on and no connection can be made. The Netgear instructions advise me to contact my isp in this case. I connect to aol via firefox. Can you help? Is this a possible permission issue?

Try this forum for help. Probably a setup issue with the MAC address.<br />
http://www.dslreports.com/forum/netgear

Similar Messages

HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

Should I use a network switch and plug my Yamaha A/V receiver and Yamaha DVD into it, then into the wireless router? Then the net into the routers net port???

HT4199 I have a Netgear R6300 wireless router and a Yamaha RX-3020 A/V receiver. An app is available to run on an Ipad. I have to reboot every morning to get it all working. Can I just plug cat6 between them, when I do nothing works, please help

Recently purchased iPad Mini. Could not get it to connect. Changed router's setting to Channel 6 and IPad connected. Even after 6.0.2 it will not connect to some home networks although it will to public networks e.g. McDonald's.

Recently purchased iPad Mini. Downloaded iOS 6.0.1. Could not get it to connect to Home WiFi using Linksys G Router. Have another Wifi Network in Home (CenturyLink provided it as a DSL/Router combo). Would not connect (nor would my iPhone 4s or my wife's iPhone 4) until I accessed the router's setting and changed to broadcast on Channel 6 and then IPad connected. I suspect the only reason the iPhone were still connected to the Linksys network is that they were before I "upgraded to iOS 6. Even after 6.0.2 the iPad and both iPhones will not connect to some home networks (its random) although thye will connect to public networks e.g. McDonald's, Panera, etc.

Recently purchased iPad Mini. Downloaded iOS 6.0.1. Could not get it to connect to Home WiFi using Linksys G Router. Have another Wifi Network in Home (CenturyLink provided it as a DSL/Router combo). Would not connect (nor would my iPhone 4s or my wife's iPhone 4) until I accessed the router's setting and changed to broadcast on Channel 6 and then IPad connected. I suspect the only reason the iPhone were still connected to the Linksys network is that they were before I "upgraded to iOS 6. Even after 6.0.2 the iPad and both iPhones will not connect to some home networks (its random) although thye will connect to public networks e.g. McDonald's, Panera, etc.

HT4623 i bought an ipod touch got itunes downloaded on my computer but can't get it to connect to ipod because it is locked it was locked when i bought it how can i get it un locked

i bought an ipod touch and i got itunes downloaded on my computer but can't get it to connect to ipod because it is locked it was locked when i bought it how can i get it unlocked?

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

HT5205 I recently bought the ipad3 with Verizon. Could not get it to connect abroad which for me defeats the purpose. My brother had at&t and his worked on the ipad2. Thoughts?

I recently bought the ipad3 with Verizon. Went abroad and it would not connect. My brothers ipad2 connected abroad, although he has AT&T. Thoughts? I travel a lot and it was half the reason I bought an iPad!
Thanks!

I am not too technology savvy. So for those like me who don't quite grasp all these cards - do either the regular Verizon or AT&T plans that you can easily purchase work overseas? If not, do I have to buy these micro sim cards in each country I visit? And the regular iPad wifi (without any cellular plan) will work anywhere in the world?

I want tabs to open at google.ca as they did before I got rid of the bing bar. Have gone to options and set it there but I still get the thumbnail page. Thx.

Instead I get the thumbnail page which Id rather not have. I x'ed out all the thumbnails so only the google.ca one is there but it's not a full page, just a thumbnail. I realize I can enlarge it. This is not a huge problem but I would like it solved.

Just to lay out the recipe all in one place:
(1) In a new tab, type or paste '''about:config''' in the address bar and press Enter. Click the button promising to be careful.
(2) In the search box above the list, type or paste '''newtab''' and pause while the list is filtered
(3) Double-click the '''browser.newtab.url''' preference and enter your preferred page:
* ''Page thumbnails (default)'' => about:newtab
* ''Blank tab'' => about:blank
* ''Built-in Firefox home page'' => about:home
* ''Any other page'' => full URL to the page
Press Ctrl+t to open a new tab and verify that it worked. Fixed?
Note: as per cor-el's suggestion, open the Google page you want and copy the "final" URL from the address bar to paste in when you update this setting. If you use a shortened version, then Google will send Firefox a redirect every time, which is a waste.

I made a Blurb book through Lightroom 5, on another computer, backed it up on an external hard drive and tried to import it into my imac. I got the picture files, but could not get the book I had worked on. How do I find my book?

I made a 'Blurb' book using Lightroom on a computer that was not mine. I backed up the book on an external hard drive and then tried to import the book into my imac. I wasn't able to retrieve my book. The photos I used for the book project are there, but the 45 page book I made is not there.
What do I need to do?

You would need to go to the computer containing the book.
Select the saved book in the Collection panel.
Go to Grid View [ G ] and select all the images [Cmd/Ctrl][A]
File>Export as Catalog and store on media you can use to transfer
Bring this catalog onto your computer
File>Import from another catalog and bring the transitory catalog into your master catalog.
It should bring the images, your collections (including your book) and other settings into your own catalog.

I tried to start using Mozilla firefox but could not get past subscribing to mesterquiz so I set a fake Telephone number 99123456. I will not pay 150 kr/week s

It seems mandatory to answer some questions about using mozilla firefox to start usin gfirefox and to chose a "gift" i.e.. an ipad to go to mesterquiz and subscribe to a service of 150kr/week
How do I get around this?

Firefox costs nothing to use, and there are no "gifts" involved. Sounds like you may have signed up for something not related to Mozilla.

After downloading service pack 1 for Windows 7 Firefox did not respond anymore (I got the startscreen, but could not do anything, it "hang"), after a roll back Firefox did work again: are Firefox and SP1 incompatible?

After implementing SP1 for Windows 7 Firefox "hang"(I got the startscreen, but could not do anything: no response). After a roll back removing SP1 Firefox works again.
I installed SP1 also some months ago and had the same problems, also then this was solved also by a roll back removing SP1.
Does Firefox have problems in combination with SP1? How to solve this? Thanks.

Followed the given advice: installed SP1 again, ran Firefox in safemode, disabled other running programs as mutorrent, still Firefox didnt work. I had internetconnection (after restarting mutorrent this did work, the app telling me what the weather outside is worked) but no Firefox: as previous time I got the start screen, but could not browse the internet.
I also tried to start the Internet Explorer and it also looked as if that application had problems (but that can also be because I did not use it for a while - old version or whatever - and it is not my standard browser).
Have again performed a roll back in order to remove SP1, now Firefox works again.
If somebody has advice it would be very welcome!

Setting up time capsule with existing wireless router and another time capsule

Hello,
I just bought my first mac (MBP) and a time capsule. We already have a wireless router, and my brother has an imac and his time capsule connected to it. The apple support people said that i couldn't use my new time capsule as a backup for my files because it would have to be in bridge mode and that would cause all sorts of problems and the backup would probably fail. That I would have to use my brother's time capsule to back up my files.
Is this true?? I find it hard to believe this issue hasn;t come up before.
Thanks,
Deborah

Thanks, Bob! If I may impose on you a little bit more, would you be able to guide me a little bit in terms of the setup?
Would I need to connect my time capsule directly to the router for first time set up?
If so, would I have to keep it connected to the router all the time after the first time set up, or can I keep it in another room?
Our wireless network was created back when we were a Windows household, so we still control it using Network Magic on an old laptop.
I unlocked the network (using Network Magic) when I tried to set up the Time Capsule (wirelessly, and before calling Apple), and after entering the network password my macbook recognized the TC and I got the good little green light on the TC. As soon as I locked up the network, I got the flashing amber light on the TC and airport utility couldn't find it anymore (using Airport utility version 6.1)... I unlocked the network again, the light turned green. I locked it back up, the light started flashing amber again...
Thanks, I really appreciate your help!
Deborah

How to set up 6th Generation AirPort Extreme to cable modem as a wireless router and then connect my 3rd Generation Time Capsule to AirPort Extreme as a wireless extender?

What is the best way to set up my 6th Generation AirPort Extreme (A1521) to my cable modem as a wireless router and then connect my 3rd Generation Time Capsule (A1355) to my AirPort Extreme as a wireless extender? I live in a small 1 story house and I currently have the Airport Extreme connected to my cable modem in the living room and the Time Capsule plugged into the wall in my bedroom. I am able to wirelessly connect to the internet using the AirPort Extreme as my router and I can also do wireless back ups to my Time Capsule. My problem is that my connection seems to be really slow! My 1TB Time Capsule back up is only half way complete and it has been 3 days! My computer has been backing up all day and night for almost 72 hours and its still not even 75% complete. I have backed up to this Time Capsule in the past and it never took this long. I am thinking that when I set up my AirPort Extreme and Time Capsule using AirPort Utility I must have set it up incorrectly or something.
How do I set up my Airport Extreme and Time Capsule for the fastest possible internet speed and back up speed?
Thank you,

AirPort Utility 5.6 works with AirPort Extreme 802.11g base stations.
It works with N version airports.
It will also show details of the AC model but cannot be used for the setup.. mostly.
I purposely got the new 6th Gen Airport Extreme so my internet connection would be a lot faster!
Your network will be much faster when you have AC client directly connected to the AE. Older client will go no faster.. but what is worse.. extend wireless is mixing new and old wireless standards.. guess what one wins.. OLD.. So when you extend wireless.. you have no improvement whatsoever. This whole post is about extending wireless.. so you cannot extend to older equipment and do any better.. maybe slightly better signal although from your comments that isn't happening either.
I would rather not have to use an ethernet at all with the TC and I don't know EOP adapters are!
If you do not use ethernet then you are going to be forced to accept slow speed.
EOP (ethernet over power). Also called homeplug in the US.
http://en.wikipedia.org/wiki/HomePlug
Provides a method of networking over power cabling that already exists in your house.
So what your saying is for the fastest internet speed and back up speed possible I should keep my Airport Extreme plugged into my Modem and keep my TC set up as a wireless extender? Then when I want to do back ups I should plug an ethernet cable from my TC to my MacBook Pro?
To spell this out.
A wireless link to an extended device will go very slowly.. if it is not direct.
So lets say you have a laptop sitting in the lounge.. Your connection goes.. Laptop- - - - - AE- - - - -TC.
That means two wireless links.. wireless has this nasty half duplex and single channel nature.. it can send or receive (Tx or Rx) but not at the same time.
Ethernet by contrast does both at once. It is full duplex.
Wireless can talk to one client at a time.. so if there are multiple items using wireless lets say 4 devices.. then your computer gets a 25% time slice. Since wireless cannot handle multiple simultaneous connections.
Ethernet by contrast can connect multiple computers to multiple destinations at the same time.. all transmitting and receiving at full speed.
When you put all this together.. there are a couple of rules for fast connection.
1. Use ethernet at all times. Where you cannot use ethernet use anything but wireless.. eg EOP (homeplug) at least to try and get rid of wireless.
2. Where you must use wireless use it sparingly and make sure it is never more than one hop.. ie never have an extend wireless (repeater is more usual term). Repeater will cause instant slowdown of 50% and maybe up to 75% just because it is so inefficient.
3. Fastest wireless is 5ghz but it has very short range.. you need to be up close and personal to get it working.
Apple routers however unless you do manual setup I suggest are set to connect to best signal strength not best speed. It will therefore use 2.4ghz at 25% less speed than 5ghz because it is 1db better signal.. this madness means you need to setup manually for the best setup.

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have utility

I just set up the airport wireless modem - with a comcast internet router - all wireless device connect seemlessly (3 Iphones, Mac Air, and a Sony Laptop) but my IPAD 1 no longer connects. It tries to but never connects. I have reset it and have airprot utility app downloaded on my IPAD - it shows the modem and the internet no connected?

Do you mean an Airport Extreme Base Station connected to a Comcast Modem?

Hi i just bought a wireless router and i cannot get it to...

hi
i just bought a wireless router and i cannot get it to work. it is a wrt54g v6. the power light keeps flashing. I tried talking with linksys to get it fixed, but nothing is working. it says to disconnect from the modem and update my firmware, but i cant get the IP address to come up on the address bar. can someone please help me out.
thank you
angela

If you have just bought the router and it has a flashing power light return the router. It is not worth trying to revive a broken router in that case. Return the router and get a properly working one. I would not want to start with a broker router even if you may be able to revive it. You'll never know what caused the problem and whether you will have more issues later.

Can I Show Time Connected When Using Netgear DG834 Wireless Router ?

When I had an old SpeedTouch USB Modem I could see the time I had been connected to the internet from a readout in the menu along the top of the monitor.
Is there a way of displaying or ascertaining this information using the Netgear DG834 wireless router?
I have discovered that by opening the Router Satus and clicking on "Connected Status" I can get a window displaying this info - but is there a quicker "automatic" way of doing it?
Ian.

Hi Ian,
Interesting one…
When you connect via a USB modem the computer is 'doing' the connecting using the modem so the computer has the 'time connected' status available locally. In the case of a router it is connected to the internet irrespective of the computer's status; on, off, sleep, or even, connected to the router. The only way you're going to get the info is from the router itself and, unless it has a setting whereby it will automatically 'inform' the computer of its connected time, I think you're going to have to carry on as you are.
I don't know that particular Netgear but used to have a different one until a thunderstorm fried it. I don't remember it having such a setting. My current Belkin certainly hasn't.
I'm quite interested to know why you want this info. Are you on some kind of PAYG tariff?
Adrian

Wireless router and base station help

Hello fellas -- I'll really, really appreciate any help I can get with this, so thanks in advance for any advice given. Here we go...
I purchased a MacBook (2.16 GHz Intel Core 2 Duo, 160GB hard drive, 2GB RAM) about two months ago. It runs Mac OS X Tiger (10.4.9). Previously, I had a Sony Vaio desktop in my downstairs bedroom, and an HP Pavilion desktop in my mom's office upstairs. I have Comcast "high-speed" cable internet service. Downstairs (where the Vaio was) I have a surfboard cable modem with three cords coming out of the back: 1.) a power cord (obviously); 2.) a cable cord that runs into the wall for internet service; and 3.) an ethernet-looking network cable. This ethernet/network cable would have normally run right out the back of the surfboard cable modem and into the network port on the back of my Sony Vaio, but in order to provide internet service for my mom's HP upstairs, the network cable went from the back of the surboard modem and into a D-Link wireless router that we bought. Another network cable then went from the D-Link wireless router into the network port on the back of my Vaio. This provided both my Vaio and my mom's HP with good, steady cable internet access.
When I bought this new MacBook, it came with an AirPort Extreme card (no base station yet) that allowed me pick up on the wireless signal from the D-Link wireless router and this provided me with internet service. To connect to the internet, I would connect to the wireless network that my computer called "default." By this point, I had shut down and unplugged my Vaio, so it's out of the picture now -- the MacBook has replaced it. However, I left the surfboard cable moden and the D-Link wireless router plugged in, and this way I was able to connect to the default network wirelessly with my MacBook, and my mom was still provided with wireless service from the D-Link router on her HP upstairs. This worked great for awhile, until eventually this default network started getting rediculously slow and started disconnecting itself every 30 to 45 seconds -- literally. For this reason, I went out and bought an AirPort Extreme Base Station at my local Apple Store.
First, to make sure it worked, I unplugged the network cable (the one coming from the back of the surfboard cable modem) from the back of the D-Link wireless router and I plugged it directly into the base station I just bought. In other words, I took the D-Link router out of the picture and plugged the base station directly into my surfboard cable modem. This worked great, and it's how I'm connected to the internet as we speak -- it's providing me with steady, fast service. Instead of connecting to the default wireless network that was slowing me down before, I now connect to the base station's network, called "Apple Network 2b1d46." There's only one problem, though -- it involved taking the D-Link wireless router out of the picture, so now my mom can't get on the internet with her HP. The solution seemed very simple -- instead of plugging the surfboard cable modem directly into the base station, I would plug the surfboard modem into the D-Link wireless router, and then plug that into the base station. I saw no reason why this wouldn't work, and I still don't, but for whatever reason, it didn't.
This is where I need help. When I try to plug it in through the router like that, I simply can't get on the internet. Everything else works perfectly -- the surfboard cable modem's lights are properly lit, as are the D-Link router's lights. The Apple base station's status light is a solid green like it's supposed to be, and strangest of all -- when I open Internet Connect to check my AirPort status, everything is fine there as well. It says "Connected to Apple Network 2b1d46," which is the new base station network that I should be connected to, and under that it says "Connected to the internet via Ethernet," yet when I try to open Safari, it says "You are not connected to the internet," which is in direct contradiction to what Internet Connect is simultaneously telling me (that I am connected to the internet).
I've tried alot of things to trouble-shoot this. I've tried FireFox and Opera, and they can't bring up any web pages either, so I know the problem isn't just with Safari -- it's that my computer just can't connect to the internet or bring up web pages, even though Internet Connect and everything else says that it's connected. I've also run the Network Diagnostics an uncountable amount of times, and all it can tell me, in all its wisdom, is that my internet connection appears to be working fine and that I must have spelled "www.apple.com" (my home page) incorrectly (it says the same thing about any other web page I try to open). I've ran the network assistant to create a new location, and it also gets the the end of the wizard and tells me that it can't connect to the internet. Finally, I've also ran the AirPort Utility multiple times and set up the base station in every possible way, but still nothing works.
On that note, I do have one question. When you run the AirPort Utility and choose "Assist Me", at one point during the wizard it asks, "How do you connect to the internet?" Right now, remember, I have the D-Link wireless router taken out of the picture (the base station is plugged directly into the surfboard cable modem). For the answer to this part of the wizard, I chose the option that says, "I use a DSL or cable modem with a static IP address or DHCP." Obviously, given that I'm on the internet as we speak, this is working fine. However, if I bring the D-Link wireless router back into the picture and plug the base station into it (the router), and then plug the router into the surfboard modem, should I still have the same option checked (the one thats says I use a DSL or cable modem with a static IP address or DHCP), or by connecting through the router, should I change my answer to one of the other two options. The second option says, "I use a DSL or cable modem using PPP over Ethernet (PPPoE)." The third option says, "I connect to my local area network (LAN)." I've tried all three numerous times, and none of them work -- I still have the same problem getting on the internet once I connect through the D-Link router, but I thought I could at least find out which one is the right option so I could stop having to keep trying all three of them. Can anyone tell me which of those three options I should pick when connecting through the D-Link wireless router (cable modem with static IP address or DHCP, cable modem with PPPoE, or local area network).
Sorry, I know that was a long one, but if anyone can answer the previous question for me and/or give me some general advice regarding my problem with getting the internet to work once I hook up the base station through the router instead of directly into the cable modem, I would appreciate it more than you can imagine.
Thank you very much for your time and help.
-- Andrew

I am doing something similar. I have the WAN port on my Linksys 4-port wired router connected to my DSL modem. My G5 and G4 computers are connected directly to the Linksys LAN ports. My older Airport Extreme (flying saucer) is connected to another LAN port on the Linksys. I had to setup the Airrport as a bridge in this configuration. I did this by using the Ethernet LAN port on the Airport instead of the WAN port. In the Airport Setup Utility I said to connect using Ethernet. This seems to work for me.
I also use manual IP addresses for everything but you will probably want to use DHCP.
Cheers,
-= Ken =-

Bought a Netgear wnr2000v3 wireless router and set it up but could not get an internet connection.

Similar Messages

Maybe you are looking for