Bought Linksys PAP2 firmware 3.1.9 need to unlock

I bought a Linksys PAP2 with firmware 3.1.9 with the understanding that it was not locked only to find that it in fact is locked. I'm not sure which provider it's locked to but I cannot do any administration on the web administration page of the PAP2. Any help would be great, thanks.

 where did you purchased the device? try to look for pap2-na so you can be sure that it is unlocked (unless the device was preconfigured by another user).  you may try to reset the device by pressing ****73738 from the analog phone connected to the device. if it will ask for password then there is no other way to access the device,

Similar Messages

  • My switch Linksys srw224g4 has problem and I need someone help

    Hello,
    My switch Linksys srw224g4 has problem that it keeps rebooting continuously and cannot bootup successfuly. Can someone tell me how to fix this problem? Firmware version is 1.2.2b , boot version is 1.0.2
    Here is console capture:
    ==================
    ------ Performing the Power-On Self Test (POST) ------
    UART Channel Loopback Test........................PASS
    Testing the System SDRAM..........................PASS
    Boot1 Checksum Test...............................PASS
    Boot2 Checksum Test...............................PASS
    Flash Image Validation Test.......................PASS
    BOOT Software Version 1.0.2 Built  17-Aug-2006  14:55:46
    Linksys SmartSwitch based on 88E6218 with ARM946E-S.
    32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...
     100%
    Decompressing SW from flash
     100%
    OK
    Running from RAM...
    *** Running  SW  Ver. 1.2.2b  Date  20-Mar-2007  Time  11:44:49 ***
    HW version is 00.03.00
    Base Mac address is: 00:1d:7e:74:b6:14
    Dram size is  : 32M bytes
    Dram first block size is  : 16969K bytes
    Dram first PTR is  : 0xF6D840
    Flash size is: 8M
    01-Jan-2000 01:01:02 %CDB-I-LOADCONFIG: Loading startup configuration.
    LZMA: Decompressing file failed!
    HOSTG_rscode_file_load: could not load file
    Device configuration:
    Slot 1 - SRW24F4G HW Rev.  0.2
    Tapi Version: v1.3.3.1
    Core Version: v1.3.3.1
    01-Jan-2000 01:01:09 %SYSLOG-F-OSFATAL:
    L FATAL ERROR: ROOT: ABORT DATA exception 
    ***** FATAL ERROR ***** 
    SW Version  :  1.2.2.16
    Version Date:  20-Mar-2007
    Version Time:  11:44:49
    Instruction            0x121fc0
    Exception vector       0x10
    Program state register 0x20000013
    *****************  SYSTEM RESET  *****************
    ------ Performing the Power-On Self Test (POST) ------
    UART Channel Loopback Test........................PASS
    Testing the System SDRAM..........................PASS
    Boot1 Checksum Test...............................PASS
    Boot2 Checksum Test...............................PASS
    Flash Image Validation Test.......................PASS
    BOOT Software Version 1.0.2 Built  17-Aug-2006  14:55:46
    Linksys SmartSwitch based on 88E6218 with ARM946E-S.
    32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...
     100%
    Decompressing SW from flash
     100%
    OK
    Running from RAM...
    *** Running  SW  Ver. 1.2.2b  Date  20-Mar-2007  Time  11:44:49 ***
    HW version is 00.03.00
    Base Mac address is: 00:1d:7e:74:b6:14
    Dram size is  : 32M bytes
    Dram first block size is  : 16969K bytes
    Dram first PTR is  : 0xF6D840
    Flash size is: 8M
    01-Jan-2000 01:01:02 %CDB-I-LOADCONFIG: Loading startup configuration.
    LZMA: Decompressing file failed!
    HOSTG_rscode_file_load: could not load file
    DelScr fatal Error: Invalid Variant type01-Jan-2000 01:01:03 %SYSLOG-F-OSFATAL: DelScr fatal Error
    ***** FATAL ERROR *****
    Reporting Task: ROOT.
    Software Version: 1.2.2b (date  20-Mar-2007 time  11:44:49)
    *****************  SYSTEM RESET  *****************
    Thanks,
    Tien

    Hi,
    Please follow the steps in this link to reload the image:
    http://www.cisco.com/en/US/products/ps9967/products_qanda_item09186a0080a36371.shtml
    And this is the link to download boot code 1.00.86:
    http://ip.gliebetronics.com:800/firmware/Linksys%20SRW2024/Firmware/
    Hope this help.

  • My just bought new ipad screen stuck one a game. Can't turn off, can't get into log in screen. I connect ipad to my imac, but message say need to unlock ipad. But my ipad screened dead. Please help!

    My just bought ipad with retinal display 32G, screen frozen at one of game my son play. Now I can't turn off ipad, I can log in ipad. I connect ipad to my apple computer, message say I need to unlock the ipad, the problem is I can't even get to ipad home screen to unlock or enter the password. Basically, my ipad is dead. I can't even know what my series number etc. Please help!
    Thanks!

    Try a reset:
    Hold the Sleep and Home button down until you see the Apple logo.

  • HT1267 I bought My Iphone 4s from Iran, I need to make an Apple Id but Iran is not in the registered countries?! I dont know what to choose? Also From Iran we do not have Credit card facility for payment option?!! Any idea how I can get FREE APPS on my Ne

    Hi there,
    I bought My Iphone 4s from Iran, I need to make an Apple Id but Iran is not in the registered countries?! I dont know what to choose? Also From Iran we do not have Credit card facility for payment option?!! Any idea how I can get FREE APPS on my New Phon?!!
    Please let me know how I can get this sorted as soon as possible!! Thank you very much

    You can create an Apple ID without a credit card, see this article:
    Create an iTunes App Store account without a credit card
    Check this post about iPhones from Iran:
    Re: Why Apple does not support from Iran? And why not open a store in Iran?

  • My office just bought me an iMac and I absolutely need to hook up a second monitor but there is no DVI connection on it, just a Thunderbolt. What do I do? Please help ASAP!!!

    My office just bought me an iMac and I absolutely need to hook up a second monitor but there is no DVI connection on it, just a Thunderbolt. What do I do? Please help ASAP!!! The imac is a 21.5" and they also already bought an HD 21.5 ASUS LCD monitor to attach to it. I'm really trying to make this setup work but this is becoming a nightmare. Any suggestions? I looked up  different VGA adapters but the only options for this would be a usb-vga connection which doesn't work on macs. Can anyone tell me if this new Thunderbolt connection will work in some way? Thanks

    Using the Thunderbolt port attach a Mini-display to DVI so long as the Asus display is equipped and capable, otherwise Mini-display to VGA will also work. The Thunderbolt port is ahead devices  which are not yet available to take advantage of the increased capacity in speed. Until the devices and connection cables are available, just use the port as a Mini-display port.

  • US-bought iMac -- now in Korea: Do I need any adapters?

    Hi everbody,
    I just bought a brand new iMac (new model) -- 20"/2.4ghz from the Apple Store in NYC last week. I'm now living in Seoul, S. Korea and just had the computer shipped here.
    What do I need to have to safely plug in my US-bought iMac here in Korea. Is there a special converter I need or will a normal plastic plug adapter (no smarts, just a piece of plastic to adapt the plug prong) solve my problem?
    Also -- does Apple sell a proper Korean power cord that I could use with no worries?
    Thanks in advance for your help!
    -CS

    I live and work here in Korea.Both of my computers were bought in the USA.
    All U need is the plug adapter, naturally making sure u connect it to a good outlet. Dont waste the money for the cord.
    Voltage here is 220v. your iMac uses free voltage which means that it automatically senses the voltage supply and adjusts for it internally.
    the plug adapter will cost about 1000 won. the Apple cord would cost about 30 - 40,000 won. one dollar = 900 won.
    plus the only place U can get the cord is at the COEX Exhibition Center or in Kangnam at the Apple repair shop. the repair shop is by the Hannam Bridge.
    have fun.
    Norman

  • In an attempt to configure Linksys PAP2 VOIP adapter, I a...

    In an attempt to configure Linksys PAP2 VOIP adapter, I am constantly receiving this message, "Your phone may be plugged into incorrect phone port. Please try the other port." Manual reboot did not solve the problem. Can anyone help?

    Hello,I am partheeban.Have you got to fix the problem.Me al so have same problem.If you sole that let me know.How you did.this is the massage i have got on my phone
    This is the voice massage i have got it from my phone.
    Connected in the incorrect phone port. Please try other port. If you believe
    your correct port. Please log on to your web account to check your states of
    your service O108.
    This is the voice massage i have got it when you pickup the phone
    immediately the voice massage will comes.
    Thanks

  • I bought an iphone5 from saudi arabia,can i use it in india?is there any requirements i have to take?many one are saying i need to unlock it,please any one help me,i did'nt activate my phone yet.

    i bought an iphone5 from saudi arabia,can i use it in india?is there any requirements i have to take?many one are saying i need to unlock it,please any one help me,i did'nt activate my phone yet.

    If the phone is unlocked then you can use it in India.
    If your phone is locked, then the only way to get the phone unlocked is to contact your phone company/carrier. The person that sold you the phone in Saudi should have told you whether it was locked or unlocked.  Contact them to check and then contact the carrier to have it unlocked if it is locked.
    Other than that there is not a lot that you can do - perhaps it was unwise to purchase a phone in Saudi - it won't have Facetime on it if you got it there.

  • Hello, I bought my iphone in japan. And now I'm in Brazil and I use it here, I need the unlock code for me to use here. please

    Hello, I bought my iphone in japan. And now I'm in Brazil and I use it here, I need the unlock code for me to use here. please

    williamjapa wrote:
    Hello, I bought my iphone in japan. And now I'm in Brazil and I use it here, I need the unlock code for me to use here. please
    Only the carrier to which the phone is locked can authorize an unlock. None of the Japanese carriers will do that. Sell the phone and buy one that works in Brazil.

  • I have bought an IPad in the US however need to return in the UK, am i able to receive a full refund? Note: i have removed the outer packaging.

    I have bought an IPad in the US however need to return in the UK, am i able to receive a full refund? Note: i have removed the outer packaging.

    I have no idea if you can do anything with it in the UK. All you can do is ask for help. Just be prepared for the possibility that they can do nothing for you because the device was purchased in the US.
    You may have to contact the store from which you purchased the device in the US to see if you can send it back to them in exchange for the Mini. This assumes you are within the 14 day window and they will accept it without all the expected packaging.
    Beyond that I don't think anyone here can tell you with any certainty what you can do under the given circumstances. All you can do is ask. The worst that can happen is everyone says, "No."

  • Bought InDesign CS4 for Mac and now need to move it to a PC. Help!

    Bought InDesign CS4 for Mac and now need to move it to a PC. Help!

    Most Adobe software is written for one of two platforms, Mac or PC.  In order to switch platforms you need to be using the most current version, so CS4 would not be supported for making this switch.  Here is a link to a page that explains the requirements for switching platforms....
    http://helpx.adobe.com/x-productkb/policy-pricing/order-product-platform-language-swap.htm l

  • Went to install os mavericks and got this message: MacBook Air Flash Storage Firmware Update 1.1 need. tried that and got: This update requires Mac OS X 10.7.5 or 10.8.5 or later, please advise.

    went to install os mavericks and got this message: MacBook Air Flash Storage Firmware Update 1.1 need. tried that and got: This update requires Mac OS X 10.7.5 or 10.8.5 or later, please advise.mac

    OK. Now, you say you got this alert through App Store when trying to download Mavericks or after you downloaded it and were trying to install it? Which is the correct case?
    The error you are getting may sometimes occur when the computer has already been updated, but I don't know why you would be getting this message. I can only suggest that you take it in for service to find out why this is happening.

  • HT4993 hi ihave the sprint iphone i bought it on ebay but i will use it at turkey i need the unlocked phone how can i unlocked this phone i am not living in usa please i need help

    hi ihave the sprint iphone i bought it on ebay but i will use it at turkey i need the unlocked phone how can i unlocked this phone i am not living in usa

    Return the phone to the seller for a refund and buy a phone that is already unlocked or will work in Turkey

  • I have bought an iphone from a friend and want to unlock it from vodaphone do I need to contact apple or just vodaphone?

    I have bought an iPhone 3GS from a friend and it is locked in to Vodaphone, I need to unlock it as I live in Spain and my friend is in the UK. Do I need to contact Apple with the IMEI number to have the phone registered to me or do I just contact Vodaphone? I need to do this asap so please help?

    Only Vodaphone can authorize the unlocking of this phone. Apple can't/won't help you.
    However, Vodaphone, like most carriers, will only authorize unlocking for customers, obviously not you. You need to get your friend to request that Vodaphone authorize the unlocking of this phone.

  • I have bought English verion In Design. I need the function of Chinese version. How can I converse it? Thanks

    I have bought English verion In Design. I need the function of Chinese version. How can I converse it? Thanks

    Ah.   I understand now.   I suspect it is the technical problem that the money keeps the account alive.
    Go to  http://www.apple.com/support/itunes/contact/  - and click on Express lane followed by iTunes > iTunes store.   Explain to them and see if they will help you raise a new account.
    Remember, your account and means of payment must relate to the country you permanently reside in.

Maybe you are looking for