Brand new hard drive and still can't get past the gray screen

i was having problems with my mac last night going to the gray screen, sometimes i'd get the folder with the question mark. i looked up for solutions and i tried every one i could find short of reformatting the hard drive. nothing worked, getting the start-up disk causes the mac to freeze on the screen with the picture of a disk and an arrow after i press the arrow to go into disk utilities. i took it to the apple store, which i wasn't really happy with my service there- i was called up immediately but then was never able to explain what was happening to the guy he just plugged in the computer, went back to helping someone else and periodically looked at my screen. i understand that they probably take care of multiple people at once so they don't get complaints about wait times, but i don't think i was really helped at all, he just ended up saying that i needed a new hard drive and if i knew how to put one in i was better off doing it myself then sent me on my way. well i bought a new hard drive and upon installing it and putting in the mac os x disk it still freezes and no solution has worked yet.

So all you need then is to know how to format the drive and install Snow Leopard.
How to erase and install Snow Leopard 10.6
https://support.apple.com/kb/HT3910

Similar Messages

My MacBook Air can't get past the gray screen with the apple logo. What's the fix?

My MacBook Air can't get past the gray screen with the Apple logo, so I can't login. Does anyone know the fix for this?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, reboot as usual (i.e., not in safe mode.) If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

New hard drive and now can't get library back!

Hi,
My hard drive recently crashed and I did not have a backup (I know, I know!). Anyway, new hard drive installed and some of my files were saved including some music files. However, when I try to add them to iTunes, they do not add. I have everything on my ipod but when I connect it, it says that I have already synched it with another computer. How can I get my music back in the library as it was before? And do I do this with the music and podcasts stored on my computer or can iget my music from my ipod to the library?

*can i get my music from my ipod to the library?*
Connect your iPod to your computer. when you get the message that it is linked to a different library and asking if you want to link to this one and replace all your songs etc, press "Cancel". Pressing "Erase and Sync" will irretrievably remove all the songs from your iPod. When your iPod appears in the iTunes source list change the update setting to manual, that will let you use our iPod without the risk of accidentally erasing it. Check the "manually manage music and videos" box in Summary then press the Apply button. Also when using most of the utilities listed below your iPod needs to be enabled for disc use, changing to manual update will do this by default: Managing content manually on iPod and iPhone
Once you are safely connected there are a few things you can do to restore your iTunes from the iPod. If you have any iTunes Music Store purchases the transfer of purchased content from the iPod to authorised computers was introduced with iTunes 7. You'll find details in this article: Copying iTunes Store purchases from your iPod or iPhone to a computer
The transfer of content from sources such as songs imported from CD is designed by default to be one way from iTunes to iPod. However there are a number of third party utilities that you can use to retrieve the music files and playlists from your iPod. You'll find that they have varying degrees of functionality and some will transfer movies, videos, photos, podcasts and games as well. Have a look at the web pages and documentation, this is just a small selection of what's available, they are generally quite straightforward. You can read reviews and comparisons of some of them here:
Wired News - Rescue Your Stranded Tunes
Comparison of iPod managers
TuneJack Windows Only (iPhone and iPod Touch compatible)
iPod2PC Windows Only
iDump Windows Only
SharePod Windows Only
iPodRip Mac & Windows
YamiPod Mac and Windows
Music Rescue Mac & Windows
iPod Music Liberator Mac & Windows
Floola Mac & Windows
iGadget Mac & Windows (iPhone and iPod Touch compatible)
iRepo Mac & Windows (iPhone and iPod Touch compatible)
iPod Access Mac & Windows (iPhone and iPod Touch compatible)
TouchCopy Mac & Windows (iPhone and iPod Touch compatible)
There's also a manual method of copying songs from your iPod to a Mac or PC. The procedure is a bit involved and won't recover playlists but if you're interested it's available on page 2 at this link: Copying Content from your iPod to your Computer - The Definitive Guide
Whichever of these retrieval methods you choose, keep your iPod in manual mode until you have reloaded your iTunes and you are happy with your playlists etc then it will be safe to return it auto-sync.

I can't get past the gray screen.

I can't log in to my MacBook. When I turn it on, the gray screen comes up and the cursor moves, but I can't click through.
What's going on? Please help!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
     a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

How can i find the mac address of a brand new iphone 5 since i can't get to the settings screen untill it's signed onto the web

I have a brand new iphone. my home wifi router has a mac filter. I can't use my phone until the wifi is set up but i cant set up my phone until it connects to the internet. is there a way to find the mac addreess without getting to the settings menu?

It's not on the box.
Try turning off Mac filtering temporarily on your router, finish the setup, then turn it back on. Or use another WiFi hotspot, such as an Apple store or a carrier's store. Or McDonalds. Or Starbucks.

I can't get past the gray screen after update of 10.10.3

downloade the new software on my 2011 Mac this morning, and after the download when the computer restarts a gray screen appear. I don't know how to get rid of it. It was working fine before the updat. Anyone have this problem?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

HT204414 does the system library need to be on the primary hard drive or can it be on my external hard drive and still be able to use the cloud?

does the system library need to be on the primary hard drive or can it be on my external hard drive and still be able to use the cloud?

I have the system Library on a second internal drive and it is syncing with iCloud with no problems. Also the Media Browser it seeing it there.
Only make sure, your external drive is directly connected and correctly formatted MacOS Extended (Journaled).

I got a new hard drive and my iMovie was deleted. is the only way to get it back is to buy it?

I got a new hard drive and my iMovie was deleted. is the only way to get it back is to buy it?

Satellite C650D-02V (PSC0YC-02V026)
When i run the disk i get an error saying that some files can't be read from file or disk..
You can obtain new recovery discs for that Canadian model from Toshiba by calling 800-663-0378.
-Jerry

Purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death" any suggestions?

purchased Lion, installed it - once I log in - i get the curtain and message to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions to hold the power button till it shuts down. Worked with the disk repair utility - fixed permissions - still can't get past the "black curtain of death" any suggestions?
My machine was patched to date 10.x.x. I was lucky to get an internet connection and I selected the option to re-download Lion... its curruently being downloaded. What if that doesn't work?
Any thougths would be appreciated.
Joe

And you have a workstation? not a notebook.
Usually a driver or hardware, nothing that Disk utility will fix.
You know of course what a Prohititory Sign is?
prohibitory sign, kernel panic
Forum devoted to Lion:
Mac OS X v10.7 Lion Communities
Tips and FAQs
FAQ kernelpanic
Resolving Kernel Panics
Avoiding eliminating Kernel panics
Lion App Compatibility Table - RoaringApps
RoaringApps Mac OS X Lion Application Compatibility
did you make sure your apps, drivers, and hardware support Lion?

My old iMac and OS 10.4 will not accept the New iTunes Version 10 application and I can't get past the screen offering to download iTunes 10. This is wrong and I need help getting past this situation. Help!

My old iMac and OS 10.4 will not accept the New iTunes Version 10 application and I can't get past the screen offering to download iTunes 10. This is wrong and I need help getting past this situation. Help!

Sure, you can get around it if you don't need the newest version of iTunes. I still use version 7.5 because the newer versions didn't strike me as offering anything I needed.
If you do need a version 10-something then you will have to upgrade your operating system to Leopard (fi your computer will support it) at least. If you need 10.5 for some reason then there's no getting around it, you will have to buy a new computer.

I just opened my new Mac Pro and I have a USB keyboard, not a bluetooth -- it doesn't recognize the USB keyboard and I can't get past the "bluetooth keyboard pairing" screen.

I just opened my new Mac Pro and I have a USB keyboard, not a bluetooth -- it doesn't recognize the USB keyboard and I can't get past the "bluetooth keyboard pairing" screen.

What specific KB?
Do you know it works?
I set my 2103 nMP with an older (black) Apple USB KB and it worked fine

I verified my email, then went to sign in and I can not get past the Sign In.

I need some help. I made an account and verified my email. I then went to sign-in and a box pops up saying I need to review my account. I go back to review it and it takes me to the support page. In other words... I can not get past the Sign In.

Thanks, Andrew for your help. Not sure if you will see this, but I did the above and it said the HD was okay. Rebooted it and still won't go past login page. Tried it again and this time typed in the line /sbin/fsck -fy and then it came up and said HD was okay, but said something about being modified. I once more rebooted, but it still won't get past the login screen. Besides taking long to reboot, as before, I am able to enter my password, but then it hangs up with the rainbow icon rotating continuously. Does this mean that the disk is corrupt or partially so, and if so, can you advise how I should proceed? TIA again.

Ipad screen is white. Restored it on iTunes. Press home and on switch goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. 16GB OS 7.1.1

The ipad screen is white. Holding buttons didn't work so I restored it on iTunes. When I press home and on switch, the screen is white, goes black then back to white with no logo at all. Can't get past the white screen. This happened after running app updates. Is there any fix besides going to Apple store? In iTunes on computer can see what is on there. 16GB OS 7.1.1

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

Help! my first mac! and I can't get past the Welcome menu window... I try to select "united states" and want to continue but nothing happens. Any idea why?

help! my first mac! and I can't get past the Welcome menu window... I try to select "united states" and want to continue but nothing happens. Any idea why?

Restart the Mac, and start over, it very well could be frozen. This is not the way you would like to start out your Mac experience!

TS1139 I'm trying to process my first iPhoto order and I can't get past the fact it won't accept my telephone number. Thinking this may be a format glitch, I have tried to get around this but no success. Any suggestions? Yours in frustration:( CW

I'm trying to process my first iPhoto order and I can't get past the fact it won't accept my telephone number. Thinking this may be a format glitch, I have tried to get around this by spacing but no success. I live in Australia and the prefix is +61. Any suggestions welcome? Yours in frustration:( CW

Experiment - or search these forums - someone discovered a solution and it was a format issue
The US format for phone numbers is 10 digits AAA-PPP-NNNN - you do not include the 01+ here typically - maybe if you can out your digites in that format it will work
Hopefully someone from down under will tell how they do it
LN

Brand new hard drive and still can't get past the gray screen

Similar Messages

Maybe you are looking for