BRAS Config for MPLS carrying PPPoE

Hi all
DSLAM----(PPPoE)---7600----(Xconnect)----7600----(VLAN/PPPoE)---(BRAS ASR1K)
we currently have a distributed access network where the DSLAMs send us PPPoE packets which we are wrapping into xconnects back to a central BRAS.
the xconnects terminate on the upstream device to the BRAS. The BRAS is connected by a VLAN trunk and each DSLAM is identified by a unique VLAN-ID.
so the BRAS gets native PPPoE frames.
I wish to extend the MPLS to the BRAS itself. So that the xconnect ( or VPLS ) terminates on the BRAS itself.
I cant see how to stitch in the PPPoE features to get this to work.
I was thinking about an external looping cable on the same BRAS device but thats a bit crap
Is there a more elegant solution?
many thanks

Hi,
You can try pseudowire headend configuration. But I am not sure its avaliable for AS1K.
http://www.cisco.com/en/US/docs/routers/crs/software/crs_r4.1/lxvpn/configuration/guide/vc41vpls.html#wp1323446

Similar Messages

SR520 config for Alice Germany (PPPoE)

I am trying to obtain a stable teleworker / homeoffice setup with our offices UC540 box.
Currently, I am using an SR520 router at the teleworker site. I configured the SR520 for one location with Cisco Configuration Assisstant and it worked okay. The I moved, and at the new loation I have Alice DSL (ex Hansenet), which requires sending PPPoE information to the access box (Siemens).
I setup the missing information out of the existing, working Netgear router, to the SR520 with CCA, but Internet access does not work. Seems the SR520 does not get any IP on the WAN interface.
Does anyone know wether this setup can be configured with CCA ?
Does anyone know a working IOS configuration for Alice / Hansenet / PPPoE / PPP / CHAP ?
I have attached my current configuration.
Many thanks for any help.

Instead of....
policy-map type inspect sdm-inspect-voip-in
class type inspect SDM-inspect-staticnat-in
pass
Could you do
policy-map type inspect sdm-inspect-voip-in
class type inspect SDM-inspect-staticnat-in
inspect
I think that will fix the issue.

Multiple MPLS Carriers/Networks

Does anyone have any experience with using 2 MPLS carriers for load balancing. We'd like to have a primary MPLS network with ATT and then a backup MPLS network with MCI. But rather than use MCI strictly for backup we'd like to load balance traffic across both networks. Most of our bigger sites will have a connection into both clouds. Anyone have any idea how we'd handle the routing for that?

I assist in supporting an environment which might almost be identical to that you want to move into.
The first issue you might bump into is the way EBGP will prefer to always use its CE-PE link if it sees otherwise equal paths. Simple solution, divide your traffic to your CEs. We do this either by using GLBP for small sites, or via equal cost paths within the LANs routing topology to the CE routers.
Second issue you might bump into is if the AS topologies are different between the MPLS providers making AS hop counts different between sites. We addressed this issue by defining and maintaining our own logical topology that looks identical between the different MPLS providers.
Both of the prior principally perform static load balancing but if you working with 12.4 or later, you might also want to look at OER. It can dynamically load balance, either with the static techniques, above, or without them.
PS:
We also deal with the situation where two sites are not on the same provider's MPLS. (Usually the result of some problem.) For this, we leak routes between the providers at major hubs permitting traffic to transit between the providers for sites that can not be reached on the same provider.

IOS VERSION FOR MPLS

Hi! i'm trying to do a lab at my university implementing MPLS. I have routers cisco 2610 series. This is my configuration:
Cisco2600-2(config-if)# ip route-cache cef
Cisco2600-2(config-if)# mpls label protocol ldp
Cisco2600-2(config-if)#mpls ip
My problem is that i can't use te "set mpls experimental topmost " command at the policy-map. My options are:
Cisco2600-2(config-pmap-c)#?
QoS policy-map class configuration commands:
bandwidth Bandwidth
compression Activate Compression
drop Drop all packets
exit Exit from QoS class action configuration mode
no Negate or set default values of a command
police Police
priority Strict Scheduling Priority for this Class
queue-limit Queue Max Threshold for Tail Drop
random-detect Enable Random Early Detection as drop policy
service-policy Configure QoS Service Policy
shape Traffic Shaping
My version of the IOS is:
IOS (tm) C2600 Software (C2600-TELCO-M), Version 12.3(15b), RELEASE SOFTWARE (fc1)
wich version do i need to run this command and configurations?? Any information will help. Thank you very much. Best regards!!

It is my understanding that you don't have that capability in those images (or platform). I didn't find the feature in the feature set of the 2600 platform. The feature you are looking for is: "MPLS Quality of Service (QoS) Enhancements"
From the feature set definition:
- MPLS quality of service enhancements allow service providers to classify packets according to their type, input interface, and other factors by setting (marking) each packet within the MPLS experimental field without changing the IP precedence/DSCP field. For example, service providers can classify packets with or without considering the rate of the packets that PE1 receives. If the rate is a consideration, the service provider marks in-rate packets differently from out-of-rate packets.
HTH,
-W

IOS version for MPLS command

What is the minimum software version for Cisco 2620XM to execute mpls?
I am running Version 12.2(24)but enable to run mpls command.
1)Router(config)#tag-switching advertise-tags
2)Router(config)# interface e0/1
Router(config-if)# tag-switching ip
Pls help!!

It looks like MPLS really does disappear in 12.4 code for the 2651XM (see below). It's too bad because I could use the features and would rather not have to replace a bunch of routers.
PE#show ver
System returned to ROM by reload
System image file is "flash:c2600-spservicesk9-mz.123-18.bin"
PE#
PE#conf t
Enter configuration commands, one per line. End with CNTL/Z.
PE(config)#int fa0/0
PE(config-if)#mpls ip
PE(config-if)#tag-switching ip
PE(config-if)#end
PE#
PE#show version
System returned to ROM by reload
System image file is "flash:c2600-spservicesk9-mz.124-7a.bin"
PE#
PE#config t
Enter configuration commands, one per line. End with CNTL/Z.
PE(config)#int fa0/0
PE(config-if)#mpls ip
^
% Invalid input detected at '^' marker.
PE(config-if)#tag-switching ip
^
% Invalid input detected at '^' marker.
PE(config-if)#end
PE#

Mobileconfig for unsupported carriers on SIM Free phones

Currently my company has several branches outside of the United States. We purchase SIM Free phones to use on unsupported carriers when a supported carrier is not available locally.
We also build mobileconfig files to control security, VPN, Exchange access, and APN configurations. All of the services we subscribe to includes tethering. We have access to the tethering APNs and when configured manually, it works flawlessly. The problem is when we create custom profile configuration, the tethering disappears but the data access still works. Today, our config files has no APNs which leaves the configuration open for individual users to enter manually. We would like however to include all of the configurations into one profile or multiple profiles pushed to the phones to include the carrier data APN, Tethering APN, and all of our internal configuration. Is it possible to do via mobileconfig files?

jraduga wrote:
How Nokia and MS can test and approve something to a point that is ready for a carrier but not have it ready for non carrier based phones is really strange. Considering the carrier versions are based on the sim-free versions initially, before Nokia and MS make changes to suit the carriers. There should be no reason why they should still be testing the sim-free version completely around the world.
Who knows? Welcome to the mysteries of large multinational corporations. Gets even worse when there are 2 of them involved. I presume the same team/teams can only do one thing at a time. As they are prioritising their large customers, us minnows have to wait till they are done first.

Config for Production client

Dear all,
I'm a new basis and now I'm working in big project ERP. I have a disturbed about config for Production client.
In scc4 we must set client role is Production and No change allowed for Objects. But in production some time we need do Open and Close Period, or change following business requirement, ... This is not allowed to do in Production client.
How do we config for Production client to cover this requirements ?
Do we need a config client for maintain Production client ? Example: Production client is 500, Config client is 100. When we need Open or Close Period or change anything, we do in 100 and transfer request to 500.
Thank you very much.
Regards,
Thanh.
Do not use text message language, the next time your thread will be deleted.
Read the "Rules of Engagement"
Edited by: Juan Reyes on Dec 1, 2010 11:06 AM

You can customize transaction to be executable although the setting in SCC4 is "productive", this is accomplished by using transaction SOBJ:
Note 1497640 - Open and close periods in productive client
You can theoretically put every customizing view there and make it "executable" in a production system.
Markus

How to use the same services-config for the local and remote servers.

My flex project works fine using the below but when I upload my flash file to the server I doesn't work, all the relative paths and files are the same execpt the remote one is a linux server.
<?xml version="1.0" encoding="UTF-8"?>
<services-config>
    <services>
        <service id="amfphp-flashremoting-service"
            class="flex.messaging.services.RemotingService"
            messageTypes="flex.messaging.messages.RemotingMessage">
            <destination id="amfphp">
                <channels>
                    <channel ref="my-amfphp"/>
                </channels>
                <properties>
                    <source>*</source>
                </properties>
            </destination>
        </service>
    </services>
    <channels>
    <channel-definition id="my-amfphp" class="mx.messaging.channels.AMFChannel">
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
    </channel-definition>
    </channels>
</services-config>
I think the problem is the line
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
but I'm not sure how to use the same services-config for the local and remote servers.

paul.williams wrote:
You are confusing "served from a web-server" with "compiled on a web-server". Served from a web-server means you are downloading a file from the web-server, it does not necessarily mean that the files has been generated / compiled on the server.
The server.name and server.port tokens are replaced at runtime (ie. on the client when the swf has been downloaded and is running) not compile time (ie. while mxmlc / ant / wet-tier compiler is running). You do not need to compile on the server to take advantage of this.
Hi Paul,
In Flex, there is feature that lets developer to put all service-config.xml file configuration information into swf file. with
-services=path/to/services-config.xml
IF
services-config.xml
have tokens in it and user have not specified additional
-context-root
and this swf file is not served from web-app-server (like tomcat for example) than it will not work,
Flash player have no possible way to replace token values of service-config.xml file durring runtime if that service-config.xml file have been baked into swf file during compilation,
for example during development you can launch your swf file from your browser with file// protocol and still be able to access blazeDS services if
-services=path/to/services-config.xml
have been specified durring compilation.
I dont know any better way to exmplain this, but in summary there is two places that you can tell swf about service confogiration,
1) pass -services=path/to/services-config.xml parameter to compiler this way you tell swf file up front about all that good stuff,
or 2) you put that file on the webserver( in this case, yes you should have replacement tokens in that file) and they will be repaced at runtime .

Config for Dispatch Intrastat

Hello Experts,
Our client has a manufacturing plant in France which is already in SAP. Now they are planning to come up with another plant in France. We will be creating a new Company Code and Sales Org. My question is that since France is already in SAP and uses Intrastat reporting so do we need to make any config for new Plant/Sales Org or is the Intrastat setting defined at country level only.
Regards,
Karan

Hello Karan,
We are going to create a new Plant as well as a new Sales Organisation. In Intrastat there is one setting where we assign Business Transaction Type to Sales Org/Item Category combination. For the reference Sales Org this setting is already in place so do we need to do this setting for new Sales Org also or does it get copied when we create new sales org with reference to existing sales org?
In my view on the current set up which you are incorporating for new plant at France, there is no need to have new Company Code and Sales organization unless and untill there is some legal requirement at EU(If export process needs to be triggered). There is not much information available on Intrastat functionality but as i understand from you, you create Business transaction type at Intrastat, and then assign business transaction type to Sales organization, My suggestion would be :- most likely you would have to extend and include the newly created Sales Organization for Business transaction type.
Thanks,
Sarthak

Issue in creating Credit Note for road carrier invoice from SAP TM system

Dear All,
I am facing issue in creating Credit Note for road carrier invoice from SAP TM system.
The following steps I have performed:
1)
1)    1) Create Freight order with Amount 20,100
2)     2) Create Freight Settlement Doc and send it to ECC. Hence PO and SES will be created in ECC with Amount 20,100
3)     3) Invoice verification (MIRO) done w.r.t. FO in ECC with Amount 20,100 and following entries posted :
Carrier A/c - 20,100Cr
GR/IR A/c – 20,100 Dr
4)    4) Created Credit Note in SAP TM against freight order with Amount 1,010 and transfer it to SAP ECC.
5)    5) By this a new PO and SES was created with negative values (with amount 1,010) in SAP ECC
6)    6) In transaction MIRO, Credit Memo was created against the freight order.
7)    7) By this it is showing value 21,110 by adding the line items of Original Purchase Order and Credit Note Purchase Order as 20,100 and 1,010 respectively.
8)    8) By posting this following are the accounting entries which is not correct:
Carrier A/c – 21,110 Dr
GR/IR – 20,100 Cr
GR/IR – 1,010 Cr
9)    9) In report FBL1N which is showing the remaining liability of value 1,010(21,100 – 20,100) instead of 19,090 (20,100-1,010=19,090) for the carrier.
Please suggest how to resolve the issue and get the correct accounting for credit memo?
Regards,
Vibhu Gupta

Hello,
Like my reply in Linkedin group, I got the same issue and solved with BADI in TM side(REQREQ...).
Regards, Marcelo Lauria

Vendor Payment Terms config for 30%advance 70% after GR

Hi Guys,
How to configure Vendor Payment Terms for " Vendor Payment Terms config for 30%advance 70% after GR "
Please suggest your expert comments.
Thanks in advance.
Regards,
Jackie

sappassion2011 wrote:
Hi Guys,
>
> How to configure Vendor Payment Terms for " Vendor Payment Terms config for 30%advance 70% after GR "
>
> Please suggest your expert comments.
>
> Thanks in advance.
>
> Regards,
>
> Jackie
Hi Jackie,
Do them in trxn OME2
Regards
Shiva

What's the best Mac Pro config for Fireworks?

What's the best Mac config for Fireworks?
I can pretty much get whatever Mac I want at work... My boss is sick and tired of watching Fireworks crash all the time... I figure a hefty processor and lots of RAM and maybe a SSD will help…
I should get a Mac Pro right? Which processor?
• Two 2.40GHz 6-Core Intel Xeon processors (12 cores)
• Two 2.66GHz 6-Core Intel Xeon processor (12 cores)
• Two 3.06GHz 6-Core Intel Xeon (12 cores)
Should I get 24GB RAM?? Or is that overkill?
I'll get a 2TB serial hard drive…
I should get a 512 GB solid state drive offered by Apple right?
Or is it possible to get a larger better 3rd party SSD?
And then maybe two 21" Displays… Two 27s seems a little much… or does it?
Thanks in advance.

Oh and what about video cards? Or is Apple's default ok? (I'm not doing hard core PhotoShop retouching or anything).

If I buy an att iPhone 5 will it be unlocked for foreign carriers?

if I buy an att iPhone 5 will it be unlocked for foreign carriers? For example, I will be living in Brazil and would like to take it there and use on my Claro account

But I read that Verizon and Sprint iPhone 5's are going to be able to be used with other foreign carrier sim cards. I cannot find similar evidence about AT&T phones.

I have a iPhone 4s from Verizon and clean esn but using for other carrier. How can I reset phone setting so I can get us contact setting? (My default contact setting is to Netherland.)

My contact setting is default for Netherland and want to resync with *228 but because of I'm not active account holder with Verizon, they can't reset it for me.
I bought it from other people and I checked the ESN , its clean one with no contract.
What's my option now? Can apple unlock it? I want to use it for GSM carrier.

Only Verizon can authorize it to be unlocked. If they won't, you'll have to sell it to someone who can use it.

Add file config for hole application?

Hi everyone,
Is there any one worked with build file config for hole fusion adf application? It is similar with web.config in .NET ASP web site. I think in jdeveloper, we can use web.xml for add some parameter but don't know how to read this parameter?
Any help is appreciate!
Thank.

User, please tell us your jdeveloper version!
In general you can read context or innit parameters from web.xml.
You get to them via the servlet context
String databaseHost =getServletContext().getInitParameter("database.host");
And to get to the servlet context use
FacesContext ctx = FacesContext.getCurrentInstance(); ServletContext servletContext = (ServletContext) ctx.getExternalContext().getContext();
Timo

BRAS Config for MPLS carrying PPPoE

Similar Messages

Maybe you are looking for