BRI and Serial link are up at the same time

Hello,
Got a question about BRI interface
Is there any way to disable BRI interface manually when primary link is up?
I had a situation where both BRI and Serial link were up and running
i reset the primary BRI0/1/0 and now BRI sub-interfaces are showing down..but still primary bri int showing up up (spoofing).
what does spoofing means?
RouterA(config-if)#do sh int BRI0/1/0
BRI0/1/0 is up, line protocol is up (spoofing) >>>>>>>>>>>
Hardware is GT96K BRI with U interface (3086)
Description: circuit id 50.ibsd.515307
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
Last input 00:00:28, output never, output hang never
Last clearing of "show interface" counters 6w3d
Input queue: 0/75/115/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
296542 packets input, 1320737 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
115 input errors, 113 CRC, 0 frame, 0 overrun, 0 ignored, 104 abort
329534 packets output, 1582923 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
RouterA(config-if)#do sh ip int brie
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 10.X.160.1 YES NVRAM up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
Serial0/0/0 unassigned YES NVRAM up up
Serial0/0/0.1 10.X.252.21 YES NVRAM up up
BRI0/1/0 unassigned YES NVRAM up up
BRI0/1/0:1 unassigned YES unset down down >>> >>>
BRI0/1/0:2 unassigned YES unset down down >>>>>>
Dialer0 unassigned YES IPCP up up
Loopback0 10.X.3.169 YES NVRAM up up
RouterA(config-if)#
Really appreaciate anyone's explanation.
Thanks in advance
SiraJ

To begin with the last question: The status as observed is in fact normal behaviour.
Spoofing is in other words "faked up". An interface that's inactive normally goes down which also causes all routes running over it to be dropped from the routing table. This status was implemented to allow dialers to keep their static routes also when the dialer was inactive. Check with the command "show dialer" to see if there is any undesired calling action.
Use an access-list to allow traffic to activate the dialer.
regards,
Leo

Similar Messages

  • New IPhone and Ipad air are ringing at the same time...

    New IPhone and Ipad air are ringing at the same time, from incoming landline/mobile phones. Help please...

    That's a new feature introduced in iOS 8 called Handoff. You can start something on your iPhone and finish it on your iPad or Mac. You can make the iPad stop ringing by going to Settings>FaceTime on the iPhone and toggling off iPhone Mobile Calls. You can do it on the iPad also.

  • My iPhone and my iPad are ringing at the same time when I receive a FaceTime call.

    I purchased anew iPhone 5s and an iPad Air last night. When setting up the iPad it asked did I want to use my number or my email. I thought I said email but every time my phone ring for FaceTime the iPad does the same. Please help!,,

    Many users use a free gmail.com email address for FaceTime and iMessage on their iPad.
    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    iOS: FaceTime is 'Unable to verify email because it is in use'
    http://support.apple.com/kb/TS3510
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
    http://support.apple.com/kb/HT5538
    How to Set Up & Use iMessage on iPhone, iPad, & iPod touch with iOS
    http://osxdaily.com/2011/10/18/set-up-imessage-on-iphone-ipad-ipod-touch-with-io s-5/
    Set Up Alert Sounds
    http://www.quepublishing.com/articles/article.aspx?p=1873027&seqNum=3
    Extra FaceTime IDs
    http://tinyurl.com/k683gr4
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Troubleshooting iMessage Issues: Some Useful Tips You Should Try
    http://www.igeeksblog.com/troubleshooting-imessage-issues/
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    Fix Can’t Sign Into FaceTime or iMessage iOS 7
    http://ipadtutr.com/fix-login-facetime-imessage-ios-7/
    FaceTime, Game Center, Messages: Troubleshooting sign in issues
    http://support.apple.com/kb/TS3970
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    iOS 7 allows you to block phone numbers or e-mail addresses from contacting you via the Phone, FaceTime, or Messages
    http://howto.cnet.com/8301-11310_39-57602643-285/you-can-block-people-from-conta cting-you-on-ios-7/
    How to Block Someone on FaceTime
    http://www.ehow.com/how_10033185_block-someone-facetime.html
    My Facetime Doesn't Ring
    https://discussions.apple.com/message/19087457#19087457
    How to watch FaceTime calls on the big screen with Apple TV
    http://www.imore.com/daily-tip-ios-5-airplay-mirroring-facetime
    Send an iMessage as a Text Message Instead with a Quick Tap & Hold
    http://osxdaily.com/2012/11/18/send-imessage-as-text-message/
    To send messages to non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
    How to Send SMS from iPad
    http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
    How to Receive SMS Messages on an iPad
    http://yourbusiness.azcentral.com/receive-sms-messages-ipad-16776.html
    Apps for Texting http://appadvice.com/appguides/show/apps-for-texting
    You can check the status of the FaceTime/iMessage servers at this link.
    http://www.apple.com/support/systemstatus/
     Cheers, Tom

  • Me and my partner are currently using the same apple id and have no space left on our devices. We are currently waiting on the iphone 6 plus to arrive and don't know how to transfer all data to the new phones.

    Me and my partner are currently using the same apple id and have no space left on our devices. We are currently waiting on the iphone 6 plus to arrive and don't know how to transfer all data to the new phones.?

    I don't know if I'm asking this all in a way that can be understood? Thanks ED3K, however that part I do understand (in the link you provided!)
    What I need to know is "how" I can separate or rather create another Apple ID for my son-who is currently using "my Apple ID?" If there is a way to let him keep "all" his info on his phone (eg-contacts, music, app's, etc.) without doing a "reset?') Somehow I need to go into his phone's setting-create a new Apple ID and possibly a new password so he can still use our combined iCloud & Itunes account?
    Also then letting me take back my Apple ID & password, but again allowing us (my son and I) to use the same iCloud & Itunes account? Does that make more sense??? I'm sincerely trying to get this cleared up once and for all----just need guidance from someone who has a true understanding of the whole Apple iCloud/Itunes system!
    Thanks again for "anyone" that can help me!!!

  • My wife and my iphones are both on the same apple id.  If I create a new apple id for her, can we still share our music?

    My wife and my iphones are both on the same apple id.  If I create a new apple id for her, can we still share our music?

    Yes.  If you are using two different instances of iTunes on your computers, make sure the music is on both copies of iTunes.
    The person with the new Apple ID will not "own" the music, as it is owned by the one with the former ID.  But the way to deal with this is for the new ID person to do Store > Authorize This Computer from iTunes' menu, then have the person with the ID that purchased the music enter his/her Apple ID and password.

  • HT4437 I have followed all relevant steps, my iPhone5 and apple TV are connected to the same wireless network, but I still cannot use airplay. When I choose the airplay option on my phone, the only option I get is "iPhone"

    I have followed all relevant steps, my iPhone5 and apple TV are connected to the same wireless network, but I still cannot use airplay. When I choose the airplay option on my phone, the only option I get is "iPhone"

    Welcome to the Apple Community Willy.
    Try the following steps, check whether things are working after each step where appropriate, before trying the next.
    Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
    Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
    Restart the Apple TV (Settings > General > Restart).
    Restart the Apple TV by removing ALL the cables for 30 seconds.
    Restart your router. (Also try removing it’s power cord for at least 30 seconds)
    Restart your mobile device.

  • For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

    For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

    For the past month, I've had an echo of my voice while I'm talking on my phone.  It's very annoying and sounds like multiple people are speaking at the same time and it's only me.  Anyone know what's wrong?

  • I was backing up my iPhone and importing photos onto iPhoto at the same time , then suddenly it says no more space available (i had 48GB before i do this and now i have 18GB) i can't find the back up or the photo anywhere , how can i delete them ?

    i was backing up my iPhone and importing photos onto iPhoto at the same time , then suddenly it says no more space available (i had 48GB before i do this and now i have 18GB) i can't find the back up or the photo anywhere , how can i delete them ? i dont need the pictures or the back ups , i want to delete them but they are not there

    Empty the Trash if you haven't already done so. If you use iPhoto, empty its internal Trash first:
    iPhoto ▹ Empty Trash
    Do the same in other applications, such as Aperture, that have an internal Trash feature. Then reboot. That will temporarily free up some space.
    According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation. You also need enough space left over to allow for growth of the data. There is little or no performance advantage to having more available space than the minimum Apple recommends. Available storage space that you'll never use is wasted space.
    When Time Machine backs up a portable Mac, some of the free space will be used to make local snapshots, which are backup copies of recently deleted files. The space occupied by local snapshots is reported as available by the Finder, and should be considered as such. In the Storage display of System Information, local snapshots are shown asBackups. The snapshots are automatically deleted when they expire or when free space falls below a certain level. You ordinarily don't need to, and should not, delete local snapshots yourself. If you followed bad advice to disable local snapshots by running a shell command, you may have ended up with a lot of data in the Other category. Reboot and it should go away.
    See this support article for some simple ways to free up storage space.
    You can more effectively use a tool such as OmniDiskSweeper (ODS) to explore the volume and find out what's taking up the space. You can also delete files with it, but don't do that unless you're sure that you know what you're deleting and that all data is safely backed up. That means you have multiple backups, not just one.
    Deleting files inside an iPhoto or Aperture library will corrupt the library. Any changes to a photo library must be made from within the application that created it. The same goes for Mail files.
    Proceed further only if the problem isn't solved by the above steps.
    ODS can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To see everything, you have to run it as root.
    Back up all data now.
    If you have more than one user account, make sure you're logged in as an administrator. The administrator account is the one that was created automatically when you first set up the computer.
    Install ODS in the Applications folder as usual. Quit it if it's running.
    Triple-click anywhere in the line of text below on this page to select it, then copy the selected text to the Clipboard by pressing the key combination command-C:
    sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
    Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
    The application window will open, eventually showing all files in all folders, sorted by size with the largest at the top. It may take a few minutes for ODS to finish scanning.
    I don't recommend that you make a habit of doing this. Don't delete anything while running ODS as root. If something needs to be deleted, make sure you know what it is and how it got there, and then delete it by other, safer, means. When in doubt, leave it alone or ask for guidance.
    When you're done with ODS, quit it and also quit Terminal.

  • Phone and my husbands iphone ring at the same time when only one of us is being called. How can I stop this from happening?

    Both my iphone and my husbands iphone ring at the same time when only one of us is being called. How can I stop this from happening?

    This post has already been answered. Why are you plugging your own site with an answer that has already been given? Not to mention that the information you are handing out is incorrect. There is no bug, there is no patch, and no one needs to delete any email addresses. If you take the time to read the posts with the correct answers, you will see that the solution is totally different than the erroneous one you have posted.
    GB

  • It is possible to charge an iPad3 over USB and transmit data over USB at the same time?

    Hello,
    it is possible to charge an iPad3 over USB and transmit data over USB at the same time?
    If yes, how?
    Thanks
    Best regards

    OK!?
    That is right that the USB data oins are not connected to +5V pin.
    But i found a description for a self built power supply for iPad.
    http://timothyb.net/DIY_iPad_2_USB_Charger.html
    and
    https://www.mikrocontroller.net/topic/262610?goto=2726627#2726627
    The description say: data pin D- need a voltage level of 2V and D+ 2,857V
    when the data pins have this special voltage levels and VCC has +5V only then the iPad is charging.
    The voltage "D+/D- coding" is the key for the iPad to charge.
    OK now back to my problem.
    The regular USB data pin voltage level is 0,3 - 3.,0 voltage. When the iPad is charging the data pins have this special voltage level. Now i try to transmit data over the usb data pins with the. Normaly the USB port transmit the data with a voltage level of max. 3V.
    And here my problem. The higher voltage level at the data pins cares therefor that the iPad stop the charging.
    Is that correct?

  • When two Computers are online at the same time, constantly losing internet connection

    I recently added a WRT160N router to my PC for a wireless Laptop elswhere in the house as well as adding a new network adapter card to my PC. When both the Laptop and the PC are online at the same time I am constantly getting booted offline and having to reset the connection, but when just the PC is on there are no prbloems and everything seems to work fine.
    Any suggestions would be helpful, thanks in advance
    Andy

    In this case i think you need to change some settings on your Router. Follow the steps below.
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    - Here select manual configuration...Wireless Network mode should be mixed...
    - Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...

  • SCXI 1112 and 1302 doesn't run at the same time

    Hi,
    I have SCXI 1112 thermocouple input module,  SCXI 1180 feedthrough panel , and a SCXI 1302 terminal block connected SCXI 1000 chassis with SCXI 1349 adapter. I am trying to measure voltage by using SCXI 1180&1302, and temperature by 1112 module at the same time. When  chassis is on SCXI 1112 runs without a problem; however, voltage reading coming through SCXI 1349 makes no sense (plus I can't run them at the same time, LAbview gives an error). While the chassis' power is off, it is the other way around, SCXI 1349 runs smoothly.
    In addition to that, a radiometer, connected to a power supply, is wired to SCXI 1302 terminal block. When power supply is on, SCXI 1112 module's temperature reading is 4 times higher than actual value. In other words, power supply effects the readings.
    Could you please give me some advice to solve this problem?
    Thanks,
    Azra

    One piece of the puzzle you left out is the DAQ card being used in the host computer. 
    Without looking at some specifics on the SCXI cards/connectors you are using, I will comment you must be careful when you are using an 1180 feedthrough module.  Keep in mind, the SCXI chassis is Signal Conditioning -- it's nothing without the DAQ. 
    I would recommend you back up a few steps, simplify the setup and test each input channel from MAX -- making sure you aren't overlapping channels between the 1180 to the DAQ and the SCXI chassis.  Remember, most data from the SCXI chassis comes in on a single channel of the DAQ through the 1349.
    Hope this might help. 
    RS

  • Peer-to-Peer Transactional Replication (three or more participating databases): What if all the nodes are working at the same time

    In the topologies that have three or more participating databases.
    What if all nodes are working at the same time? "The topology is not partitioned by time.".
    location 1 will do insert/update/delete/read in the same time location 2 also will do insert/update/delete/read  .......
    **Data that will be added by each location is different(each location has its own primary key ranges).
    Is it recomended to use Peer-to-Peer Transactional Replication in such scinarios?

    Read these
    https://msdn.microsoft.com/en-us/library/ms151196.aspx
    http://www.brentozar.com/archive/2012/01/highly-available-local-replication/
    The only problem that you have to tackle is what happens when the same data is being updated in multiple locations at the same time. If that is not a possibility with you then p2p is a good choice. Check the above links you will have a better understanding.
    Regards, Ashwin Menon My Blog - http:\\sqllearnings.com

  • Can i connect the printer to a wireless network and a usb computer conneconnection at the same time

    Can I connect my Officejet Pro 8600 by Usb and wireless at the same time, I have a very slow Network at this time.

    Hello gilldenc
    To answer you question yes. You can have one computer attached via USB and to a wireless router at the same time. What router are you using? Is it your internet connection that is slow? Usually your internal home network is much faster than your internet speed.
    Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
    When a solution is found please mark the post that solves your issue.

  • Can an Airport extend a wireless network and support a USB printer at the same time?

    Can an Airport extend a wireless network and support a USB printer at the same time?

    Yes, if the AirPort Express is extending the wireless signal produced by another Apple router. The Express cannot wirelessly extend a network produced by a non-Apple router.
    In addition to extending the network and connecting a printer, AirPlay can also be enabled on the AirPort Express, with all services operating simultaneously.
    Please note that only the print function will work if you connect an All-in-One type device to the USB port on the Express. Advanced features like copy, scan, mainentance, etc are not supported when an All-in-One device is connected to the USB port on an AirPort router.

Maybe you are looking for