Bridge CS4 Does Not See External Drive

Very suddenly, Bridge is not seeing the external USB connected driver I use to store recent photos. I read a similar message here and the writer was told to add the drive to favorites. That appeared to work for him, but I could not do that since the folder doesn't appear under Computer in the favorites section either. The drive appears in Windows Explorer. I am using Vista 32. Any suggestions?
Fran

Did you power up or connect the external drive after Bridge had been started? I've observed that Bridge only includes drives that were attached and active when Bridge was launched; it does not add a drive to its folders list if that drive is started after Bridge is active. With your external drive on (and appearing in explorer) try exiting and relauching Bridge.

Similar Messages

  • Bridge CS4 does not see ACR presets in Develop Settings

    I think that this is new with CS4. I create a Preset in ACR in the Preset Panel. That Preset works fine on photos in ACR. The Preset is listed in the Camera Raw Settings folder in the Finder.
    But, when I try to apply the Preset in Bridge via Edit > Develop Settings, the Preset does not appear. Is this correct? I believe that a preset did appear in CS3 in Bridge Develop Settings.
    The preset was created with a Raw file from the 1DS MkIII. Could it be camera-related?
    Am I missing something here?
    Thanks,
    Sonny

    Strange. I Quit Bridge. Relaunched Bridge, and the Presets now appear in the Develop Settings list.
    I presume that I should not have to Quit and relaunch for the presets to appear?
    I created another preset. It only appeared in Develop Settings when I again quit and relaunched Bridge, even though it appears in the Camera Raw Settings folder.
    Sonny

  • Windows 8 does not see hard drive on Satellite A200

    Windows 8 does not see hard drive on A200.
    How to install?

    > with Vista works fine,
    Does this mean that Vista is still installed or is HDD visible while Vista installation setup?
    Some notebooks HDD controller needs SATA driver in order to be able to install system.
    Sat A200 is a little bit older but I dont think the SATA driver is needed here to install Win 8.
    I guess you didnt any SATA drivers to install the Vista right?
    Set the BIOS to default and try to boot again using Win 8.

  • MBA mid-2012 does not see external display on wakeup

    My mid-2012 MBA does not see external displays on wakeup. VERY annoying
    I have a BenQ 24" HD display connected by HDMI and it is not seen by the Air on wakeup. I have to open the laptop, pull the mini-DV plug out 3 or 4 times before the display is recognised - some of the time. Most of the time requires a reboot with multiple cable/plug inserts.
    What an absolute POS this mid-2012 MBA is! Apple finally fixed the garbage colours on external displays in 10.8.4 but the issue of recognisisng external displays remains. Its a crock. Totally regret buyiing this POS.
    Have reset PRAM, SMS, cleared prefs etc etc ad nauseum. No solution with any of them. After almost a year of this garbage, the laptop is close to being thrown out as e-waste.

    macbook pro 13" 2012
    osx 10.8.4
    adaptor
    http://www.maplin.co.uk/mini-displayport-to-dvi-adaptor-454323
    display: philips 230c1hsb
    i have reset PRAM but nothing happens

  • Imac does not see external speakers

    Running an iMac with 10.8.2 and it does not see external Bose speakers

    Got the same issue here; it has worked for some time, but then suddenly it stopped.
    : (

  • Phototshop CS4 does not  see all of 8GB my RAM memory

         I have not posted anything on this site.  I have a 27" 2.8 Ghz quad core i7  iMac and CS4 does not see more then 3 GB of my system RAM I have 8 GB of RAM.
             It  shows up on my info screen  I am running 10.6.2 and CS4 is suppose to be running in native 64 bit mode with Snow Leopard 10.6.2? I am at a lose and I do not know what to do?  
    Kristyanna Virgona
    Dunsmuir, CA

    It  shows up on my info screen  I am running 10.6.2 and CS4 is suppose to be running in native 64 bit mode with Snow Leopard 10.6.2?
    It is not.
    Please read »Allocating Memory with 64-bit Processors« here:
    http://kb2.adobe.com/cps/404/kb404440.html

  • My new mac mini does not see usb drives, but in hardware info the usb is visible

    my new mac mini does not see usb drives, but in hardware info the usb is visible
    i'tried several usb flash drives even brand new ones, they are visible onder hardware info but they are not on the desktop nor in the finder.
    what is wrong and doe anyone has a solution ?

    It does not show up in disk utility, its only visible through systeminformation.
    When you plug in the USB flash drive and then refresh systeminformation it becomes visible.
    To remove it I shut down the computer because I cannot eject the USB device anywhere.
    After starting up again when I have removed the flash drive it has gone from the systeminfo USB list.
    By the way my USB mouse and keyboard are working fine, I also changed ports of these and they still keep on working so I don't think the USB ports are defect.
    I guess it some kind software problem, and because I'm new to Apple I do not know much about it how to solve this.

  • HP Notebook 9628nr does not see DVD Drive no optical drive in device manager

    for some reason it does not see the dvd drive this happen after I flash the bios which was recommended from the HP website can anybody tell me how to fix this problem

    Im having a problem like this, DVD not appeare in my computer and system devices, after that a webcam will broken also( unknow device USB); solve: damaged motherboard, one of bridges- north probably
    regards 
    and watch your motherboard properly

  • Installer does not see hard drive, how do I mount

    Initialized Hard Drive with current volume and as mac extended and zero'd out memory. This drive came out of a PC that had been out of whack and drive was partitioned wrong in the PC. It worked fine to load mac OS 9.2.2 and has 18 gigs free. When I boot off of the Tiger disc it does not see the hard drive at all. Neither does the disc utility function. I checked the firm ware and it is up to date. Ran disk warrior and it says all is ok. Is it something simple?
    I can't figure out what it is I have over looked. Thanks

    Try this instead:
    1a (If this is the startup drive.) Boot from your OS X Installer Disk. After the installer loads select Disk Utility from the Installer menu (Utilities menu if using Tiger.) Be sure to use the installer disk for the version of OS X you intend to install.
    1b (If this is a non-startup volume or external drive.) Open Disk Utility in the Utilities folder of your Applications folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
    If this is the second drive in your computer, be sure you have jumpered the drive as SLAVE (assuming the original hard drive is jumpered as MASTER.)

  • New Airport Extreme (2014) does not see USB Drive

    Just fired up my new 2014 Airport Extreme and attached a Toshiba 3 TB USB Drive. My new (late 2013 iMac) does not see the new drive in Disk Utility.
    The Extreme works in all other ways; ie, as a router, as a wireless node.
    It came to me formated as a Windows drive, so I attached it directly to my MacBook Pro (which saw the drive) and reformated it as a Mac Drive (Journaled, GUILD). It showed up just fine on the MacBook Pro desktop.
    When I reattach it to the Airport Extreme, it still does NOT show up in Disk Utility on the iMac.
    Help Please

    When I reattach it to the Airport Extreme, it still does NOT show up in Disk Utility on the iMac.
    That drive will not show up in Disk Utility on the Mac.....since the Toshiba hard drive becomes a network drive when it is attached the AirPort Extreme.
    Disk Utility will not display a network drive. It will only display drives that are connected directly to your iMac via USB, FireWire, etc.
    Check using AirPort Utility to see if the AirPort Exteme recognizes the drive.
    Open AirPort Utility, click the AirPort Extreme icon, then click Edit
    Click the Disks tab at the top of the next window that appears
    The drive will appear here if it is recognized by the AirPort Extreme.
    In the example below, my WD Drive is connected to the USB port on the AirPort Extreme.

  • [SOLVED] New install does not see SSD drive

    Ok, I have a DFI motherboard which at first did not recognize my new Intel SSD drive I have installed. After updating the BIOS, it now correctly recognizes it. However when I run the 2009.2 cd and try to prepare the drives, it does not show any drives listed?
    /sbin/fdisk -l
    does not show any drives either so it looks like arch cant see any installed HD's which makes since, but the motherboard does show the new Intel SSD as a Sata drive right under my DVD player?
    Any help?
    Edit: I hooked up my old Seagate drive and it shows up fine. Any idea on why this SSD is not playing nice?
    Solved: I have come to the conclusion this has nothing to do with the Arch install, but is simply a hardware issue with my motherboard. I installed the SSD drive in my wifes pc, it seen the ssd as a sata drive while booting, it seen it when arch was initializing, it seen it when I did a fdisk, and when i finally tried to install, it was there too!!
    So there must be some issue with my old DFI MB. I will work on that or upgrade..Thanks to everyone who helped out...
    Last edited by banshee28 (2009-02-28 16:48:07)

    lilsirecho wrote:
    I had trouble with my throttle device not making contact with the data lines when connected to USB.
    I assume the SSD has the same connector as the motherboard and the cable can be reversed end to end to test for performance.
    I use a multimeter to verify the presence of power to the device.
    Sata cables are known to be flaky.
    Throttle devices use 5vdc power from USB connector and are connected to esata cables at the same time since sata ports do not supply power.  The connections for throttle are on opposite ends of the device.
    I am not familiar with the SSD power setup but assume it is 5vdc as well.
    No other suggestions here..................
    Yes, the cable should be able to be reversed as the ssd drives are identical compared to normal sata drives in respect to the cable connections: one sata data connection and one power. I will try some different cables and see if that helps. I did try a new port on the mb which did not work, and when i used the current cables on my older seagate drive it worked fine
    Last edited by banshee28 (2009-02-26 13:15:52)

  • G4 disk utility does not see hard drive

    I am helping someone with a G4 Quicksilver. She is running 10.4 but only has disks for 10.1 and 10.2. When I boot with the 10.2 CD, disk utility does not see the hard drive. I was thinking of connecting her computer to my MacBookPro (Intel, 10.5) via target disk mode and then running Disk Utility. Is that crazy? She is suffering from slow startup and grey screen. I've disconnected the periferals, safe booted, reset PRAM. She really needs Disk Utility.

    with the 10.2 CD, disk utility does not see the hard drive.
    Disk Utility from 10.2 should see the hard drive (the drive name should appear in the left box). If it does not, the drive is malfunctioning or has a loose cable.
    If you attempt to Verify, it will complain that there are illegal values in reserved fields in several different record types. Using this older Disk Utility to repair a 10.4 disk may cause more problems than it solves.
    As Tom \[Texas Mac Man] says, you should only repair 10.4 and later disks with 10.4 and later Disk Utility:
    HT2648- Only use Mac OS X 10.4-compatible disk utilities with Mac OS X 10.4 volumes
    • If you boot the regular Hard Drive (no CD/DVD required) while holding down the Shift key, it will do a quick check of the Hard Drive, then boot up in "Safe Mode". This will fix any simple Disk problems.
    • 10.4.3 and later can do a Disk Utility Verify of the Boot drive, "live" (but cannot Repair "live").

  • Does not see optical drive

    My IMac does not see the optical drive, however, it is visibable in windows 7.  I'm running Parallels

    Exactly. It can only be connected to one at a time. You have to eject it from Parallels for it to be used by the Mac.
    I initially thought you were using Boot Camp.

  • Capture mode does not see external camera

    When I use the capture in iMovie, it only allows you to choose the built in iSight camera, and the external web cam is long listed as a choice. The external works fine in other programs (like skype).
    Is iMovie intentionally crippled to only work with iSight in capture mode? Or am I doing something wrong?
    THanks
    bob

    Thanks for your help...
    It is a Logitech Quickcam Pro 9000 using drivers from mac.
    It does show up in USB section under apple system profiler.
    It is connected through a powered hub (I have tried it directly connected with no difference).
    It is recognized fine in other programs, such as Skype (you can change from isight to external web cam).
    I downloaded and installed iGlasses 2, but that did not solve the problem. Curiously, if memory serves me correctly, photobooth only works with isight internal, but after iGlasses 2 install, it works (only) with external (when external is available).
    Any other ideas on why iMovie does not see the external web cam?
    bob

  • My time capsule does not see external hard drive

    I just got a new time capsule and am hoping to use it as a wireless bridge and NAS. 
    I've got it set up as a bridge and that seems to be working correctly, but when I plug my external hard drive into the time capsule, I can't see that external drive show up anywhere.
    Has anybody else run into this issue?
    The hard drive is a WD Elements 3 TB USB 2.0 Desktop External Hard Drive - WDBAAU0030HBK-NESN.

    I can't see that external drive show up anywhere.
    If the drive is formatted correctly and communicating with the Time Capsule, then it will be displayed when you open AirPort Utility, click on the Time Capsule icon, click Edit, and then click the Disks tab at the top of the next window. Example:
    Remember that since this drive is a "network" drive, it will not be displayed on the desktop until you manually mount the drive.

Maybe you are looking for