Bridge mode and extended mode together?

I just received my new milk jug Extreme AC today, yay! I bought this in the hope that it might mitigate some of the reception issues I have been battling in my home. I currently have the 4th gen Extreme (the one with the hobbled radios) and the 3rd gen Express, and I would like to use the old Extreme in bridge mode while wirelessly extending to the Express from the old Extreme. (Yes, I would love to hard-wire but that isn't realistic right now.) Anyone have any success doing this, or any suggestions?

It wouldn't be a wireless daisy chain as I have infrastructure
Thanks for clarifying that, since it was not mentioned at all in your first post. We saw things like "wirelessly" and "I would love to hard wire, but....." and assumed (when we should not have) that you were talking about wireless for the network.
hardwire the two Extremes together with the AC doing the DHCP heavy lifting.
That would be best way to connect the two Extremes together. Set up the new "ac" Extreme as the main router, then connect an Ethernet cable from one of the LAN <--> ports on the new Extreme to the WAN "O" port on the older Extreme. The setup utility will practically configure everything for you.
I suppose I could do something similar with the Express but I am okay with the bandwidry tradeoff If it can wirelessly piggyback from one of the Extremes.
As long as the Express is located where it can receive a good quality wireless signal from whichever Extreme, that should work OK. Extending with the Express is a compromise deal no matter how you look at it.......since even if you decide to connect to the Express using Ethernet, the port on the Express will only handle 100 Mbps.
Strange as it seems, it is often better to take the bandwidth hit and extend using wireless with the Express, since the signal will often be faster this way than using Ethernet.

Similar Messages

Bridge mode and router mode

hello,
I want to understand the basic operation, difference and advantages of both Bridge Mode and Router mode?
i also want to know in which case i should go for Bridge mode and Router mode?
regards
Devang

It realy depends on your requirements.
Mainly bridge mode is used for multicast support, Multiple DMZs + FWSM, server initiated connections or for seemless migration from previously installed "bridged load balancing environment".
Some of the differences are
In bridge mode you do not need additional config for "Direct server access" / "Server Initiated connections"
Broadcasts are dropped in routed mode whereas they are bridged in bridge mode.
LB functionality is same in both modes.
Syed Iftekhar Ahmed

Timeline window missing button to switch between frame mode and timeline mode

I'm using Photoshop CS6 Extended.
This is what my timeline looks like now.
In tutorials they refer to a button that should be to the left of the drop menu that says "forever". The button is supposed to allow you to switch between frame mode and timeline mode.
this is what the timeline window looks like in timeline mode and with the button that allows you to switch.
I've already tried reinstalling and upgrading to CS6 extended, as some forums suggested.
Please help. Animation is the core reason that I need photoshop and without this button I'm extremely limited. Thanks.

OK. This should work. Copy and past the below script into Script Editor, save it as an AppleScript application to the Desktop. Double-click it and it should change to grayscale. Double-click it again and it'll toggle back.
tell application "System Preferences" to activate
delay 1
tell application "System Events"
tell process "System Preferences"
click the menu item "Universal Access" of the menu "View" of menu bar 1
click the radio button "Seeing" of the first tab group of window "Universal Access"
click the checkbox "Use grayscale" of tab group 1 of window "Universal Access"
end tell
end tell
tell application "System Preferences" to activate
delay 1
tell application "System Events"
tell process "System Preferences"
click the menu item "Universal Access" of the menu "View" of menu bar 1
click the radio button "Seeing" of the first tab group of window "Universal Access"
click the checkbox "Use grayscale" of tab group 1 of window "Universal Access"
end tell
end tell
tell application "System Preferences" to quit

What is difference between TEXT mode and BINARY mode?

Hi,
          What is difference between TEXT mode and BINARY mode? In TEXT mode what is "ENCODING DEFAULT".
OPEN DATASET wl_filename FOR INPUT
                          IN TEXT MODE ENCODING DEFAULT.
OPEN DATASET wl_filename FOR INPUT
                          IN BINARY MODE .

Hi vishnu,
1. files like .TXT files are considered to be text,
   and other files like .EXE . DOC etc are binary files.
2. In text files, after each line, there are two
   internal binary characters
one for line feed and another one for newline.
3. But, we don't have any meaning for it,
   when we view such files in notepad, for eg.
   Hence, to only get the understandable content,
   we should open such TXT files, in text mode.
(we can also open them in binary mode,
but we will get two extra characters after each line,
   and such two extra characters are meaningless
for interpreting the text)
4. In binary mode, each byte by byte is considered,
   without any meaning.
regards,
amit m.

UI Control options do not appear for TCD mode and Webdynpro mode

Hi guys,
When I open the screen Start option in eCATT for ECC 7.0, there is no options for TCD mode and Webdynpro mode, only have for SAPGUI mode. So pls help to me find the options for these modes.
Thanks in advance,
Thien

Hello Friend,
This has been corrected by 640 SAPKB64023 and 700 SAPKB70016.
Please install the relevant SP to your system.
Thanks.
Eric Monteiro

Iphone in recovery mode and DFU mode but PC still doesn't recognize device

HELP! My iphone 4 just keeps blinking the apple logo for hours! I tried the recovery mode and DFU mode, the first time went well, but it started to blink again after I restored it. Now I'm doing the same steps going to recovery mode and DFU mode, they work on the phone but for some reason, my laptop doesn't recognize any device connected. I tried everything on the internet and still wont work. WHAT CAN I DO???
by the way, Mine is windows 7.

it needs repair
Peace, Clyde

Region Monitoring iOS 7 : didEnterRegion method is not calling when app is killed by user or by OS in iOS 7 only. It is working fine when it is in background. and the same code is working fine with iOS 6 for both app in suspended mode and background mode.

Region Monitoring iOS 7 : didEnterRegion method is not calling when app is killed by user or by OS in iOS 7 only. It is working fine when it is in background. and the same code is working fine with iOS 6 for both app in suspended mode and background mode. What changes I have to made to work great in iOS 7 also.

I rewrote code for debugging purpose and tried to catch error using GetLastError();  method,
but it only printed 0. Below is code snippet; I think Create() throw an exception
and code goes to catch block.
LONG ConnectTS(CString strIP, UINT n_Port)
try{
          ErrorLog(0,0,"ConnectTS is calling Create [is going to call]","");
          if(!Create())
// Exception Line
n_Err = GetLastError();
return NET_INIT;
catch(...)
                   DWORD errorCode = GetLastError();
                   CString errorMessage
                   errorMessage.Format("%lu",errorCode);
                   ErrorLog (0, 0, "Image
System", (LPTSTR)(LPCTSTR)errorMessage);
                   return  IS_ERR_WINDOWS;
Output: -
ConnectTS is calling Create [is going to call]
Image System
0

Lightroom print mode and Color mode grayed out

Both print mode and color mode selections are grayed out not allowing me to select them. Help

I see you haven't gotten much input so far from the Mac experts...
As a Windows user without an Epson printer myself, I can't comment on why you might have color problems under the covers where the software doesn't seem to be following the chosen settings. However, perhaps I can get you thinking about how to further diagnose the problem...
The obvious thing I see is that you've chosen "Photoshop Manages Colors" in the main dialog, which implies your intent is to shut off color-management in the printer driver itself. So to me the graying out of those settings in this case seems to make sense.
Have you tried a test print using the "Printer Manages Colors" setting?
Also, to try to test whether color-management isn't being turned off in the printer (regardless of what the grayed-out settings show), do you see any improvement if you use "Photoshop Manages Colors" but choose a standard profile, such as sRGB IEC61966-2.1 for the Printer Profile setting?
-Noel

Page mode and pdf mode views are different?

Hi,
I am using BO XI R2.
I have a report. When I view the report in page mode its showing the number of pages as 4.
But when I view the report in pdf mode its showing only in 1 page.
How can we make the report view same in both pdf mode and page mode?
Are there any seetings need to be done?
Thank you,
Regards,
Gowtham.

''afew2 [[#question-1054433|said]]''
<blockquote>
I refreshed FF 36.0.4 on invite. Since then "save page as " and "save image as" are not working -- no response when clicked.
In Safe Mode, same problem.
I serached past forum discussions and found several occurrences, but no convincing response.
</blockquote>
I tried troubleshooting plugins, none appeared to be causing the problem.
I installed 36.0.1, but no difference. Went back to 36.0.4, still no change.
I ran a malware check with Malwarebytes, no change.
A past thread here suggested deleting localstore.rdf, which I tried, no result.
People have had this problem in the past. No one has any idea of how to fix it?

Using both power saving mode and offline mode caus...

So I am having a very strange problem. I have been using the Situations App (formerly Nokia Situations) to automatically put my phone into offline mode, and power saving mode over night. 9pm to 6:30am.
Recently the phone as started refusing to leave the offline mode in the morning. Even if I try to change the profile manually it says "Unable to change profile". The only way I can get out of offline mode is to reboot.
I uninstalled Situations, and manually put the phone into offline mode and power saving mode. By the morning I had the same issue, stuck in offline mode until reboot. So it's not the App causing the problem. I've tried a soft reset, same problem still.
I also noticed that over-night (from fully charged before 9pm) to 6:30am I used about 70% of my charge. (A combination of power saving mode and offline mode is killing my battery!)
I would have to go to work and immediately put my phone on charge! I.e.. 12 hours of offline + power save has drained my battery almost completely.
Last night I decided to use the Situations App to put the phone into offline mode, BUT NOT activate power save mode.
This morning the phone had virtually full charge and it had no problem returning to online mode. So it's ONLY if I use BOTH power-save and offline. (Tonight I will try using power-saving mode and NOT offline mode to see if it's only the power-saving mode causing the issue!)
If I manually enter offline+power-save mode, and then try to return to on-line/non-power-save mode, relatively quickly, i.e.. Not over-night, everything is fine. It's only over night the problems start!
Any help?
Rob
PS. I also have the problem where using HSPA+ causes my phone to drop from the network and stop being able to receive/make phone calls. But disabling HSPA+ works around this for now, I think this problem is unrelated however.

I have a similar problem. My 808 PureView loses 70% of its charge overnight if I leave it in normal profile without power-saving. To deal with this issue, I started using the situations app to put the phone in power saving mode overnight. That solved the problem (although I never put my phone to offline mode). This is a weird problem because throughout the day my phone doesn't use 70% of charge, but it does overnight while doing nothing!
I have also experienced the second problem, losing cellular and internet connection, on my 808. I have started a thread to deal with this issue.
http://discussions.nokia.com/t5/Nseries-and-Symbian-Smartphones/Nokia-808-PureView-loses-cellular-an...
I believe it is a firmware bug that causes this problem.

My MacBook pro will not startup. I get a blank grey screen no logo appears so I can't chooseadiffer t drive nor boot from DVD. Safe mode and verbose mode also don't change blank screen.

It was running slow with the colored spining appearing often. This started happening weeks ago with Yosemite so I formatted the disk with the DVDs that came with the mid 2011 MacBook pro, 10.6.8. I then installed Yosemite on an external drive and this morning i was booted from the external hd with Yosemite and it stopped recognizong mouse clicks so I forced a restart and now I'm stuck with the blank grey screen. Safe mode and verbose mode also do not work.

Lao Bo,
yes, you can locate and copy a file from your HD to a USB key using UNIX commands. If you know the exact name of the file which you’re trying to locate, try this:
find / -iname filename -print
This command will search your entire internal disk for the particular filename. If you know that it’s within a particular user account, then you can save search time with this variation:
find /Users/username -iname filename -print
Either variation of this command will print all files found which have the given filename. Presuming that you’re able to identify the correct file, you can copy it to a USB key using the command
cp -p filename_returned_by_find /Volumes/USB_volume
If you’re not sure which volume name your USB key has, this command will show you what the possibilities are:
ls /Volumes
Please let me know if you have any trouble with these commands.

Can someone explain what recovery mode and dfu mode are?

title says it all.

The main difference between DFU mode and Recovery mode is the iBoot bootloader. iBoot tells the iPhone/iPod touch/iPad what to do when it turns on, eg. load up iOS version whatever (for me, still 4.2.6 on my Verizon iPhone). When you upgrade your device's firmware, it goes into recovery mode.That way, iBoot can make sure you're flashing into a firmware that's equal to or greater than the current version of firmware you have installed. When you enter DFU mode, there isn't this limitation, so you can flash any version of iPhone OS/iOS that you want, provided the device is compatible with it and Apple is still signing for it.
If this answered your question, tell me. If it didn't, well, tell me and I'll add more!
Hope I helped!
--CS

How to print Individual mode and Collective Mode for Goods Receipt

Hi Friends,
Right now I am working on Smartforms on MIGO transaction.
My Client requirement is that all items that have been received should be printed on one form in
Collective mode.More specifically in the transaction MIGO only the items checked OK should print on
the form. It Should also allow the user to print Items in Individul mode.
Could anybody please specify on what basis( fileds ), I will be able to segregate the items.
how can I write the select stament so that when the user selects collective mode and accordingly
should print. same for individual mode.
Kindly help me.
Regards,
Xavier.P

In MIGO tcode you strcture like GOHEAD-XNAPR and GOHEAD-WEVER
if you check GOHEAD-XNAPR = X and select GOHEAD-WEVER Individual mode and Collective mode.....

Unable to enable archivelog mode and flashback mode

Hi,
I have oracle10g installed on Linux machine.
Everytime i try to enable ARCHIVELOG mode and FLASHBACK through the DB EM console and during the restart of the database, the database just startup and gets mounted, but does not get open. and not able to get the database to archive log mode.
and when i startup the database through the sqlplus i get this following error:
ORA-32004: obsolete and/or deprecated parameter(s) specified
i am not able to enable successfully archive log mode and flashback mode.
in sqlplus i did the following and got the following:
SQL> archive log list;
Database log mode No Archive Mode
Automatic archival Disabled
Archive destination USE_DB_RECOVERY_FILE_DEST
Oldest online log sequence 13585
Current log sequence 13587
so i was thinking maybe it is the archive log start sequence that is creating error.
because long back i had the database in archive log mode and because the archive log files got filled up, i disabled the archive mode and had to delete the archive log files.
Can someone help me bring the database in archive log mode which i am not able to successfully execute.
Thanks in advance,
Philip.

Hi,
yes i looked in to the init.ora file and i got this
orcl.__db_cache_size=1308622848
orcl.__java_pool_size=167772160
orcl.__large_pool_size=16777216
orcl.__shared_pool_size=167772160
orcl.__streams_pool_size=16777216
*.audit_file_dest='/home/oracle/oracle/admin/orcl/adump'
*.background_dump_dest='/home/oracle/oracle/admin/orcl/bdump'
*.compatible='10.2.0.1.0'
*.control_files='/u01/oradata/orcl/control01.ctl','/u01/oradata/orcl/control02.ctl','/u01/oradata/orcl/control03.ctl'
*.core_dump_dest='/home/oracle/oracle/admin/orcl/cdump'
*.db_block_size=8192
*.db_domain='mslabs.noaa.gov'
*.db_file_multiblock_read_count=16
*.db_name='orcl'
*.db_recovery_file_dest='/u02/flash_recovery_area'
*.db_recovery_file_dest_size=64424509440
*.dispatchers='(PROTOCOL=TCP) (SERVICE=orclXDB)'
*.java_pool_size=159383552
*.job_queue_processes=10
*.open_cursors=300
*.pga_aggregate_target=562036736
*.processes=150
*.log_archive_start=FALSE
*.remote_login_passwordfile='EXCLUSIVE'
*.sga_target=1687158784
*.shared_pool_size=157286400
*.undo_management='AUTO'
*.undo_tablespace='UNDOTBS1'
*.user_dump_dest='/home/oracle/oracle/admin/orcl/udump'
and there is a
*.log_archive_start=false
so do i have to delete it?
Thanks,
Philip.

What is the difference between LTE mode, CDMA mode, LTE/legacy 3GGPP mode, and Global mode in Preferred Network?

What is the difference between LTE mode, CDMA mode, LTE/legacy 3GGPP mode, and Global mode in Preferred Network?

Great question alczervik!
LTE- is our 4G network.
All CDMA/LTE Legacy are going to be related to our 1X, 3G/ EVDO network.
Global is GSM. Meaning you can use Internationally.
I hope this helps.
VanessaS_VZW
Follow us on Twitter @VZWSupport

Bridge mode and extended mode together?

Similar Messages

Maybe you are looking for