Bridge mode not supported for lap1261N

Hello,
I have a WLC2504 and 2 LAP1261N (converted from autonomous to lightweight) with release 7.0.116.0 and I want to create a point-to-point mesh link between the 2 APs. When trying to change the APs mode from local to bridge I receive the message "This AP does not support bridge mode" even if the release notes say that mesh is supported on AP1261N. I tried to change the mode from gui and also from CLI. Any suggestion?
Thanks,
Paolo

in aIOS you can tell it to bridge on the 2.4GHz Radio, it's not ideal but it can be done.
for WLC based:
The Cisco 1130 and 1240 ( all indoor AP ) are equipped with the following two simultaneously operating radios:
•2.4-GHz radio used for client access
•5-GHz radio used for data backhaul
The 5-GHz radio supports the 5.15 GHz, 5.25 GHz, 5.47, and 5.8 GHz bands.
http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.0/design/guide/MeshAP_70.html
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Similar Messages

Long mode not supported during import Oracle solaris 11 for vritual Box...

Hello buddy,
I try to import Oracle solaris 11 into Oracle vritual Box. but it shows ''Long mode not supported,Rebooting ....". Then reboot again and again..
what is going on ? My PC is WinXP 32bit.
Thanks

user1934450 wrote:
Hello buddy,
I try to import Oracle solaris 11 into Oracle vritual Box. but it shows ''Long mode not supported,Rebooting ....". Then reboot again and again..
what is going on ? My PC is *WinXP 32bit* .
ThanksUse the forum search function before typing a new question.
You might find that whatever you want to ask is already discussed in the forum.
Then you won't have to make a post.
Your question has indeed already been asked a few times, and recently.
Take a look at the search results.

Mid 2010 Macbook Pro to a Samsung Tv. (Mode not supported)

Hi, I have a macbook pro mid 2010, when connected to an external tv, i get the mirroring option, however when i uncheck the mirroring option (cause i need 2 desktops screen instead of one), my external monitor shows " Mode not supported ". I have a samsung LCD TV. It works perfectly with mirroring option, but I don't want a mirroring option..... Can anyone help?

I have a MacBook Pro 15 inch early 2011.
The new features available in OS X Yosemite like Continuity, Handoff,etc are not supported in this model.
I did upgrade RAM to avoid any possible slowdown.
I found replacing the HD with SSD is too expensive for a 4 years old model.
Replacing the CPU/GPU is not for amateurs.
If you think that rebuilding a Mac part by part is a viable option, please go ahead and rebuild it.
Best.

Monitor says VIDEO MODE NOT SUPPORTED after changing display settings

HELP! I am about to have a nervous breakdown with my mac mini! I hooked up the mac to my Philips LCD via DVI. No problem at all. But because the screen is only 15" I wanted to play around with the display settings a bit. So I changed the resolution from it's original 1204x768 to the one higher (not sure of numbers) and to my HORROR, I now can't get any picture at all - it says "VIDEO MODE NOT SUPPORTED". I have tried everything I can think of. I have rest the P-RAM, I have unplugged all cables, plugged the back in again, I bought the mac into work and hooked it up to my monitor and changed the resolution back to 1024x768 which is what it was on originally and that STILL didn't work. I can see the Apple logo and then it goes black and comes up with the error message. HELP! What am I doing wrong - I can't believe one click of a mouse button has rendered my display useless!!!

Welcome to Apple Discussions!
Try booting the mini without the display connected, and then, once the system is running, connect the display. This will often force the system to default to a low resolution, and then correctly detect the display when it is connected.
If that doesn't help, with the display connected, boot into safe mode (hold the shift key down when starting up) and once the system is running, change the resolution to 1024x768, and ensure the correct refresh rate is selected. Rebooting normally ought then to give you a good display.
If all else fails, boot into safe mode with the display connected, and then in the Finder's file menu, use the 'find' option to search for 'windowserver' (no quotes). You should get 2 or 3 results, including one with a string of alphanumeric characters. Move all of them to the trash and restart normally.

Mac Pro to Samsung HDTV - "Mode not supported"???

Alright, so I have just received my new Mac Pro in the mail yesterday and wanted to hook it up to my television - a 1080p Samsung (Samsung LN-T4671F) HDTV. I am using a DVI-to-VGA cable. I feel I should probably explain the entire situation so that it's all clear.
The first time I started the computer after plugging it into the TV, the Apple logo with the Loading, spinning thing (not the multicolored wheel) showed in beautiful 1920x1080. After loading, the screen jumped to a lower resolution for a second and then went black, finally giving me a "Mode not supported" error. Thinking it was just a little hiccup, I restarted the computer and after the Apple logo screen, it showed me a screen on how to put batteries in my mouse (or something along those lines, I didn't really look), and then it had me set up my wireless keyboard. After this, it showed me the WELCOME video and allowed me to log on to my computer and start using it.
After about 15 minutes, I was going through the system prefs and came across display. Thinking maybe I should lower the resolution to better see text, I clicked on a lower resolution around 1600xsomething. The screen went black and gave me the "Mode not supported" error again. I thought I could just wait a few seconds and if I didn't confirm the resolution, it would go back...but it never did. After trying to restart my computer a number of times and receiving the error message each time, I booted in Safe Mode, which I am in right now.
I went into the sys prefs and made sure the resolution was set to 1920x1080, which it already was, and restarted the computer. Error again. I went into the settings of my TV and went to PC and had it auto correct the resolution to the input. Error again. I have been running in Safe Boot since - no sound is annoying - and enjoying the display in full 1920x1080 (1080p)...so the set obviously supports it (and the manual says it does too).
My video card is an NVIDIA GeForce 8800 GT. What's most annoying is that it's pretty obvious that the display supports this resolution and yet won't allow it to work outside of Safe Boot mode.
Please help

Had the same problem with an AOC 1080p TV, trying to connect to it using VGA cable.
Ivan's earlier post clued me in to solution:
- Plug in the TV, get the "Mode not supported" message on the TV
- Open the Display Preferences, you should see the display preferences for the laptop "Color LCD" monitor. Click the "Gather Displays" button - this should bring the display preferences for the TV behind the laptop preferences window. Switch to the TV's display preferences window.
- In the TV's display preferences window, switch refresh rate down to 59.9 Hertz (your TV may need different refresh rate, but on mine I only get options for 59.9 or 60).
That did it for me!

"Mode not supported" when connecting MacBook Pro to HDTV

When I connect my MacBook Pro to the SAMSUNG widescreen HDTV and hit "Detect Displays", it does detect it as VGA Display and it gives me a bunch of options for resolutions and refresh rates, but there was no "Options" tab where I could check or uncheck "Overscan" and even keeping the refresh rate at 60 Hz, and even trying mirrored and non-mirrored screens, nothing worked. It still said "Mode not supported". I used a dual-link DVI to YPbPr cable which I just bought and my friend can connect his MacBook Pro to his HDTV with the same cable, but it doesn't seem to work for me. What's wrong?

Try using an app like to get the stranince resolution:
SwitchResX – The Most Versatile Tool For Controlling Screen Resolutions On Your Mac
Display Menu from Mac App Store
The monitor specs
Native resolution1440 x 900
Resolution720p
Supported DTV resolutions576i
Supported computer resolutions640 x 480 (VGA)
PC InterfaceVGA (HD-15)
Video InterfaceComponent, composite, HDMI, S-Video, SCART
From:
http://www.cnet.com/products/samsung-le19r86wd-19-lcd-tv/specs/

G5 with samsung 52" tv Mode not supported

Does anyone know how I can make my Powermac G5(single 1.8 ATI Radeon 9800pro) work with my Samsung 52 inch TV at HD resolution
I am attempting to convert my old Powermac G5 into a media computer. At some point I may want to add a blu-ray drive.
When I use the DVI on the G5 with a DVI to VGA adapter and connect to the TV via its VGA input. There is no picture and the TV says "mode not supported".
When I connect a second monitor to the ADC (via ADC to DVI) I can get the G5 to show up on the TV in mirror or extended mode (if I set the resolution to 1024 x 768 or less).
I have tried hocking up a monitor via VGA, setting the resolution to 1024x768, then shut done, restart with TV attached and still "mode not supported"
I have also tried making the TV as the main desktop in extended mode then restarting without the second monitor and still "mode not supported"
I tried a DVI to HDMI adapter but I got nothing "searching for signal" I would assume this should work so it might have been bad so I am going to exchange it and get a new one and try that.
?

I had to do the same, that is, accept a lower resolution for my LCD TV.
Using a Geforce 6800 GT, I have an interesting mix of "i" and "p" resolutions, but, as with the 9800 Pro, no 1920x1080p.
Just as well, though, as I couldn't read the text at highest resolution.
I'm pretty sure that this is simply a case of the high resolution 16:9 ratios not being supported in these older cards.
The resolutions that are available in the firmware of the cards are predominately for 16:10 ratio screens.
Remember, HDTV is a lot newer than most all AGP graphics cards.
I guess, when I have time, I'll have to play with DisplayConfigX and see if there is hope.

HT201310 what do you do when apple tv says mode not supported

My apple tv stopped working and the tv says either no signal or mode not supported. I have restarted, unplugged the HDMI cables and restarted again. I have not updated any software. This Apple tv is new since December 14. The TV I have is older Samsung HD.
Can anyone assist?
Thanks

sounds like you raised the resolution to fullhd 1080p and the samsung can't cope
To select a video mode:
Press and hold both Menu and Menu up/scroll on the Apple Remote for about 6 seconds. Apple TV will cycle through different display resolutions.
When Apple TV reaches an acceptable display resolution and "If you can see the Apple logo, select OK" appears on your TV screen, press the Play button on the Remote.

Mode Not Supported message on Sony BDPS3100 Bluray Player

Hi,
I bought a Sony - Smart Wi-Fi Built-In Blu-ray Player Model: BDPS3100 last weekend. When I play any DVDs on this player, I get a message saying 'Mode Not Supported. Please change the resolution of the external device'. I have connected this to a Samsung 1080p LED TV through HDMI cable. I get Netflix and other apps displayed properly on the TV and it works great with Wi-Fi connectivity. The only issue is that it is not playing any DVDs. I tried playing the same DVD on my laptop and it worked. So no issues with the DVD. I tried connecting the HDMI to both HDMI1 and HDMI2 ports on the TV but still no luck. I also tried chaning the Output settings in the player to reduce the resolution to 780p and 480p as well, still no luck in playing the DVD. I have not tried a Bluray disk yet. Any pointers on how to get this fixed? Oh yeah, I've tried switching off the player and turning it on but with no luck. Read somewhere that holding the STOP button for 10 secs will make the player reset the settings and play the disk but that too didn't work. So am lost at this point on how to play DVDs on this player. Any help would be appreciated.
Thanks

Do you have a laptop that has an HDMI in? Probably not, but just checking.
It may be a bad laser. Try a blu ray and see if that works

Mode not supported when trying to connect mac to tv

I'm trying to connect my Mac to the TV as I do nearly every day using my HDMI cable via the apple HDMI adaptor (don't know exactly what that cable is called). But when I try it cuts in and out in fuzziness for a bit then eventually comes up with the error message on my tv "mode not supported". I can't see any visible faults in the cables at all. Do I need to replace one or both of the cables? Or is there something else wrong? If it's the cables, how do I figure which needs replacing without having to buy both if it's only one of them? Help!

Hi Sneuby,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue on connecting to your Television from ThinkPad T440s.
Recently have you updated the system with any of the application or with drivers from Windows update?
Check uninstalling the Graphic driver from the system.
Please let us know the findings once you have performed the above steps.
Best regards,
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Coldfusion dev installer wont work - "installer user interface mode not supported..."

i just downloaded the os x version of coldfusion 7 mx
developer edition (for the thrid time making sure the download
wasn't corrupt) and extracted the zip and launched the installer by
double-clicking it. the install screen pops up where it lets you
choose what language and i press ok. almost instantly i get an
error message to pop up that says... "Installer user interface mode
not supported. Unable to load and to prepare the installer in GUI
mode."
umm... what?!
does anyone have any idea what's going on and why the
installer is misbehaving?! thanks!
: : michael

and the answer for others stuck on this...
the problems is an installanywhere bug where if the anything
in the directory path contains special characters like "!" or "#" ,
it causes problems with the install. in my case, the directory path
had a "!" in it... hope this helps someone else out!
: : michael

Row based Target only mode not supported

when i try to execute a mapping i am getting the following error
Row based Target only mode not supported
what can be the reasons for this

Hello Michael
Check if you have a procedure (other than pre or post mapping) in your mapping. Every part of a mapping after a procedure can only be generated in row-based mode.
Hope this helps
Mate

"mode not supported"ATV3 VGA Kanex ATV Pro

hi
Apple TV3
Samsung LED projector via VGA
Kanex ATV Pro VGA-HDMI convertor
Macbook Mavericks
all i get is mode not supported?
ta
JJ

Digger65 wrote:
thanks
bit of a shame as this cable/convertor was recommended on these boards by another user and was definately not cheap
I may have recommended this based on my own experience with it and the fact that it is designed for AppleTV specifically and is actually sold by Apple.
Have you contacted Kanex support to query what the issue might be?
Might be worth trying to cycle display resolutions with the remote, see black screen recovery:
http://support.apple.com/kb/ht3176
I have not used mine for a few months as I got a new HDMI equipped projector - it is not impossible that Apple have scuppered functionality with a software update though.
If you cannot get it to work can you return it to the vendor? I would not have recommended this device if Apple weren't selling it for this very purpose - even if a software update prevented protected content playback it should not stop you using Airplay of non-protected material.
My suspicion would be some kind of incompatibility when the device is working out what resolutions the projector supports. It could even be a faulty Kanex adapter.
AC

Mode not supported error on my mac mini help!!!

I have an 18 month old mac mini with a proview monitor.
The problem is that for the past month whenever I have restarted my mac i intermittently get a black monitor screen after the apple loading one and a monitor error message box saying 'mode not supported'. I thought it was a monitor problem, tried the auto reset button ect on it and tried ever display setting on my mac to no avail. Detecting displays in the sys prefs would also cause this problem and under my warrenty with PC world they are sending me another monitor.
If i reboot the mac by the power button on the back eventually after anything between 10 - 30 times it will all be ok. (not good for my mac or my sanity!) and only ok till i need to restart, sleep or turn off the mac.
Tonight I tried to boot from the install disk, monitor working ok this way and ran disk utility, a few permissions repaired but no other probs.
Ive firewired it to my old imac to try and see if i can change any settings but cant and the monitor is showing the firewire flashing about no probs.
So it seems its my mac thats the problem, short of a full install does anyone have any ideas?
Im just stabbing in the dark so far so could use some help
many thanks
Elizabeth

got it sorted by resetting the p ram

Changed resolution by mistake and have lost everything "mode not supported"

Guys,
This one is totally my own fault but ive managed to crash my Apple TV and was wondering if someone may be able to assit me with a solution?
Apple TV was working fine on my samsung HD TV and i was playing about with the settings.
I belive i was in "resolution" at the time and the setting was 'auto'.
For no reason other than my own stupdity, i changed the resolution to 780p or something like that and the screen went immediately blank.
All i get now is "mode not supported".
Ive held down + and menu and done the scan and it wont retrueve my previous settings.
Ive also tried - and menu and still nothing.
Why didnt i just leave it alone.
Any ideas folks on how i can get this back working and restore to auto?
Panicking.....
Simon.

Have you tried restarting it.

Bridge mode not supported for lap1261N

Similar Messages

Maybe you are looking for