Bridge or Router Mode?

I have adsl modem asus dsl13 (mode adsl2+ ). Provider has a PPoE.
What a proper option for TC - bridge or router?

You can do either bridge on the modem and router on the TC.. or router on the asus modem and bridge on the TC.
There is hardly any difference in overall performance.. since adsl is the limiting factor here.
But a few things to consider.
Pro router in the TC
1. The TC is a much faster router than the asus, if you need speed. (For normal setup makes no difference)
2. The TC often behaves better when it is the router to clients running time machine. (TC should be main router in the network if you keep having issues and losing connection with it).
Pro router in the Asus.
1. The TC is peculiarly apple, and misses out some things important. eg QoS, very important if you are running voip phones, upnp, very important if you run gaming consoles.
2. If you run the Asus as the main router you have direct access to the modem stats. This is difficult behind a bridged modem.
3. You can run PPPoA, which is slightly more efficient encapsulation method if your ISP supports it. For many people the ISP does not support pppoe so they have little choice. Sometimes PPPoA is the preferred method by the ISP and is just more reliable.
For the vast majority of people there is no right answer. Pick what works for you.

Similar Messages

  • CSM bridge vs router mode

    Hi,
    Can the CSM be used in both the bridge and router mode for different VLANS ? Or does it need to use all router mode and all bridged mode ?

    you can have a mix of both.
    Gilles.

  • CSM concurrent bridge and router mode

    Hi,
    Is it possible on the CSM to use bridge and router mode at the same time ? Or is it only router mode or only bridge mode ?
    E.g. in the example below, when using HTTPS entering the vlan 3 , it will be bridged to vlan 3....But when using HTTP entering vlan 3...it will be routed to vlan 4... Will that work ?
    Thanks
    vlan 3 client
    ip address 3.3.3.1 255.255.255.0
    vlan 3 server
    ip address 3.3.3.1 255.255.255.0
    vlan 4 server
    ip address 4.4.4.1 255.255.255.0
    vserver HTTPS
    vlan 3
    virtual 3.3.3.10 tcp https
    serverfarm HTTPS
    serverfarm HTTPS
    no nat server
    no nat client
    real 3.3.3.11
    inservice
    real 3.3.3.12
    inservice
    vserver HTTP
    vlan 3
    virtual 3.3.3.11 tcp http
    serverfarm HTTP
    serverfarm HTTP
    nat server
    no nat client
    real 4.4.4.10
    inservice
    real 4.4.4.11
    inservice

    HI Michel,
    first of all you can run bridged and routed mode at the same time but you can not define the same vlan as client and server. If you would change the above config from vlan 3 server to vlan 30 server and place the reals in vlan 30 it will work. A proper layer 2 configuration is for sure the prerequisit.
    Kind regards,
    Joerg

  • ISE iPEP + 3rd party device VPN bridge or route mode

    Dear All,
    I would like to get some advice from the community regarding my idea.
    We would like to integrate ISE iPEP with a 3rd party VPN device using bridge mode.
    However i can only find documents describing the following scenarios,
    - routed mode with VPN device
    - bridge mode with Wireless Controller
    So the questions is that is bridge mode supported if i would like to integrate ISE iPEP with a 3rd party VPN device or is it even possible to achive this kind of deployment?
    Thank you in advance.
    Best Regards,
    Erik Molnar

    Thanks for the reply Marcin.  Both of your suggestions are good ones, however in this scenario both DC firewalls are alive at the same time, so there needs to be some kind of logic on the device at the remote site to say that it should only use tunnel B if tunnel A is down.
    Thinking on this, is it possible to run an 'interface' or 'routed' mode IPSEC VPN with the ASA?  I know this is possible with the Fortigates and think it's the default mode for Junipers.  If that were possible we might be able to have both tunnels up and have OSPF run over them which would be another way to solve this problem.

  • How to set WRT54G v7 router so signal is forwardet- using bridge or repeater mode?

    What i need to set in WRT54G so its signal is beeing repeated?
    I want to use WRT54G v7 as to who internet comes in and it works like that right now and it has passw admin changed and WPA2 personal set up
    I have another router tenda w311r+ and there i have options in WDS- Lazy, Bridge and Repeater modes..
    Lazy mode is without asking BSID but others ask so i asume Lazy repeats every routers around signals..
    But what then is difference in Bridge and Repeater mode?
    I wasnt able to set all up corectly..
    Read tutorials about w311r+ and doing similar couldnt get it work..

    1
    In tenda i have
    Wifi settings
    BSSID NameTenda123 Passw123 <---- This is not same as WRT54G settings, do i need to make it like that also? Even channel the same?
    WDS settings
    Repeater ESSID Mac of WRT54G and WifipasswofWRT54G <--- this is the same as set inWRT54G
    2
    And do i connect from computer to NameTenda123 to get repeated signal from WRT54G ?
    Or the same name as reapted signal router i need to connect? BSSID of WRT54G? And do i need to set in tenda wifi settings witch now are different then WRT54G wifi settings but in Tenda WDS repeater settings are set..
    Maybe i need to set Tenda wifi off and only set WDS to be on?
    3
    Also to WRT54G i log in to 192.168.0.1 and maybe i need to set Tenda to 192.168.0.2 ? and something else?

  • CSM route mode and bridge mode can exist at the same time?

    I'm using CSM on ver 4.x,and I used to the bridge mode for firewall load balance,for a new requset,I have to create a new server/client vlan,but the original firewall load balance was effected when I issued the server vlan command,and I'd like to use route mode for the new server farm,I'm wondering that route mode and brige mode can't exist at the same time,because it seems it doesn't make sense.Any reply will be very appreciated.

    you can use bridge mode and route mode at the same time.
    Traffic with desintation mac address being the CSM will be routed, otherwise it will be bridged.
    Gilles.

  • ACE bridge mode , FWSM routed mode

    i have the following senario:
    MSFC ---vlan 777----FWSM----vlan160---ACE----VLAN180
    FWSM is working in routed mode and vlan 777 is shared between the MSFC and FWSM
    ACE is working in bridged mode and vlan 160 is shared between the FWSM and ACE
    vlan 180 is the server side vlan
    i want he FWSM ip address to be the Server gateway while ACE module in
    bridge mode
    i create bvi interface but i can't ping from ACE to FWSM or from FWSM to
    ACE
    if i change ACE to routed mode , i can ping to FWSM
    any body can help me in this issue?

    The config looks good.
    I would look at the arp table on FWSM and ACE when the ping fails and also capture a sniffer trace of ACE tengig interface and see if the ping request goes out - on which vlan - and if we get a response.
    Is evertyhing else working ?
    Like ping through the ACE module ?
    Your config does not show a 'no shutdown' on the vlan interface, but I assume you fixed that already.
    Gilles.

  • Bridge mode and router mode

    hello,
    I want to understand the basic operation, difference and advantages of both Bridge Mode and Router mode?
    i also want to know in which case i should go for Bridge mode and Router mode?
    regards
    Devang

    It realy depends on your requirements.
    Mainly bridge mode is used for multicast support, Multiple DMZs + FWSM, server initiated connections or for seemless migration from previously installed "bridged load balancing environment".
    Some of the differences are
    In bridge mode you do not need additional config for "Direct server access" / "Server Initiated connections"
    Broadcasts are dropped in routed mode whereas they are bridged in bridge mode.
    LB functionality is same in both modes.
    Syed Iftekhar Ahmed

  • Cuestion about CSM on bridge&router mode

    Hello!!
    Plese help me with this cuestion about CSM connection modes:
    We have 2 Cat6500 with a CSM inside of each (CSM1 on Cat6500_1 and CSM2 on Cat6500-2)
    The CSM1 is on bridge mode with Vlan31 for Client side and Vlan131 for Server side.
    The CSM2 is on router mode with Vlan30 for Client side an Vlan2 for Server side.
    We want to join both switches for redundancy purposes (switches and CSMs).
    We want to merge the two Client Vlans (include the logical IP segments) on a /23 mask.
    But the cuestions here are:
    Can we keep the original config (bridge mode and router mode) on the CSM1 (for example)
    considering this Module as active and CSM2 as standby?
    Is there any consideration to take in count in order to configure this? (Some examples...)
    Thanks in advance
    Pedro

    yes, you can mix bridge more and router mode and so merge the 2 configs.
    Gilles.

  • CSS: Bridge Mode + Router mode

    Hi,
    I have a CSS with many interfaces, all of them bridging.
    I need to include one routed interface. however, front end vlan is defined bridging, the new bac kend interface is to be routed with front end.
    mix og bridge mod and route mode, will it work
    mix of front end defined bridged, back end defined routed, will this work
    Please advice
    Regards
    SS

    This forum is dedicated for Cisco MARS (Security product) dicussion.
    Please ask your CSS-related queries here:
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Data%20Center&topic=Application%20Networking&CommCmd=MB%3Fcmd%3Ddisplay_messages%26mode%3Dnew%26location%3D.ee7814f
    Regards
    Farrukh

  • Difference between bridge mode and routed mode on CSS

    Hi,
    Could some one tell me the difference between routed mode and bridge mode.
    Regards
    Neha

    Hi,
    routed mode:
    The CSS acts as a router, it routes packets from the client to the server. The server has the ACE configured as default-gateway.
    There is a client-side VLAN and a server-side VLAN. These VLANs have different subnets.
    Bridged mode:
    The CSS acts as a bridge, it switches frames from the client to the server. The server has the upstream router configured as default-gateway.
    There is a client-side VLAN and a server-side VLAN. These VLANs have the same subnet, but different VLAN IDs. The ACE bridges the client traffic from the client-side VLAN to the server-side VLAN.
    Bridged mode would be most used in case one cannot change the servers IP addresses, or if address space is an issue.
    Hope this helps.
    Kind regards,
    Dario

  • Can VIP and Rservers be in the same subnet in ACE Routed Mode

    Good Day,
    Sorry for the lengthy post.
    Currently I have a 6509s running in VSS mode with ACE30 in each chassis.
    I have 5 vlans, which the VSS is the L3 interface for each. 1 Vlan is for management, the others are the data vlans for the servers.
    The ACE is configured in bridge mode, with all VLANs going to a specific context (non Admin).
    Some of the Host on each VLANs are not utilized for load-balancing. The default gateway for each VLAN is configured on the VSS.
    I would like to setup the ACE in the routed mode, without having to change the IP address of each servers on different VLANs.
    Basically I want to turn off the SVIs on VSS and move the L3 interface on the ACE Context, and let it perform the local routing for all the hosts.
    I was going to add a new /30 L3 interface between the VSS and ACE to be utilized for default route traffic coming from the ACE Context, and static routes from VSS to ACE for traffic destined to host that are being load-balanced and not being load-balanced. Basically force the traffic through the load-balancer in/out.
    For future deployment, I was planning on using different IP address for the VIPs, and Real servers (most likely RFC 1918).
    From most of the examples I have seen the VIP and Rservers are in different Subnets. But because I am trying to not change the IP address of the rservers and VIP, I wanted to know if the VIP and Rservers can be configured to be in the same subnet where the ACE is in routed mode.
    Unfortunately I don't have a spare ACE to test scenario.
    As always any help would greatly be appreciated.
    Regards,
    Raman

    Link-local addresses are usually the self assigned IP address that a device will set when a DHCP server cannot be found. These are the addresses with 169.254.x.x subnet.
    If the router is assigning IP addresses for your network, then they will usually have a different IP subnet, possibly 192.168.0 for D-Link. And this subnet would be for the wired and wireless connections. So it would be more a case of bridging the two network topolgies rather than routing them.
    The network host is busy message could be more to do with the driver and the IP protocol selected when creating the queue than the connection being broken between the Mac and printer. If you were to open Network Utility and select the Ping tab, enter the IP address of the HP and set the pings to 4, pressing the Ping button will soon show if there is a path through the wireless to the printer.
    If you get a response to the ping you could then open Safari and type the ip address as the URL. This would then connect to the internal web page of the printer and possibly let you enable an IP protocol like LPR so that you can use LPD on the Mac instead of Bonjour to connect to the printer.
    As for the driver, you could look at using a Gutenprint driver instead of the HP driver or the hpijs package to get past the limitations that some printer drivers have with network connections.

  • Does ACE-30 support multicast in routed mode?

    We currently have ACE20's, which only support multicast in bridge mode.
    Was wondering if it's the same on ACE30's, or if Cisco finally implemented support for mcast in routed mode.
    thx
    Kevin

    Could you please confirm if this applies to both ACE20 & ACE30, or just ACE20?
    If both, when does Cisco plan on supporting mcast in routed mode?
    thx
    Kevin

  • Can I configure csm as one arm and routing mode at the same time?

    My csm currently is configured as the routing mode and bridge mode, resently I have a service requirement which I think the one arm mode should be the best resolution. Can anybody let me know if there will be any affect if I add the one arm mode to the currently production environment?
    Thanks in advance.
    Jason

    Gille,
    Thanks for your quick response. I notice you have same opinion about the one arm mode in your other post, but I think in the multi-tire data center design with fw in bridge mode and csm in one arm mode with RHI, do give us a lot of flexibilty. If I use policy routing instead of source nat, can I overcome these limit you metioned?
    Do you know who csm could handle the TFTP traffic? I may have too much question, I am realy looking for your suggestion.
    Thanks
    Jason

  • ACE bridge and routed interface in the same context

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:Standardowy;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Hello
    I am wondering if it is possible to configure one ACE context to support both routed and bridge interface?
    I would like to have a bridge-mode context but in the same time I would like to have a separated OOB interface for management.
    If it is possible how they could interact to each other?
    Thank you in advance for any answer
    Regards
    Lukasz

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:Standardowy;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Hello
    We've just tried to configure bridged and routed interfaces at the same time in the lab and we've had a problem.
    When we added the def gw for the bridged config we noticed that we had an issue with the traffic src by the rservers in the routed config.
    When we deleted the new def gw, the problem disappeared.
    I am attaching the lab config.
    When we added to it the following line
    ip route 0.0.0.0 0.0.0.0 10.1.1.163
    reals B1-B10 could not communicate to the outside world.
    Do you know why it does not worked and what could we do to fix it ?
    Thank you in advance.
    Regards
    Lukas

Maybe you are looking for

  • A query with respect to creation of the  shared Objects.

    Hi , I am having a query with respect to creation of the  shared Objects. I have seen a example where the Author is creatining Shared Object as shown below : SharedObj = null; sharedObj = SharedObject.getLocal("myTasks"); and there is nothing related

  • Photo web gallery

    Is there any automated way to create a photo web gallery in fireworks or a third party plug in? I'm using Fireworks MX

  • Vision Acquisition Software installed, BUT why is the IMAQdx missing from the function palette?

    I just installed to the labview 2011, and many other modules and softwares including this VASAugust2010. But the IMAQdx is missing from the function palette (vision and motion). However the NI-IMAQ 4.5, IN-IMAQ IO 2.4.0 and NI-IMAQdx 3.7 are all clea

  • Ipod nano third generation: no music after sync.

    I have a Ipod nano third generation upgraded from 1.1.2 to 1.1.3. Now it shows no music music after syncing. In itunes however, it shows data on my ipod. This can't be removed, unless I restore my ipod. Syncing videos and pictures do work fine. I hav

  • Sub Var in FR

    I am using System 9.3.1. While creating the FR using the Studio, I am not able to get the sub var from Essbase. Other than that everything is working fine. Anyone encountered similar problem? Thanks