Bridge static IP using only one interface

Hi All,
I started a thread yesterday at serverfault, without much luck so far http://serverfault.com/questions/510361 … ly-one-nic
So the problem is that I have a bridged interface configured (br0) which bridges two physical interfaces (eth1/eth2) - bridging works as expected and packets traverse through the bridge properly. My problem comes from a static IP address configured on the bridge:
br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1488
inet 10.0.0.1 netmask 255.0.0.0 broadcast 10.255.255.255
ether 00:24:9b:04:3b:a7 txqueuelen 0 (Ethernet)
RX packets 3623 bytes 332062 (324.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1494 bytes 154380 (150.7 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Now the problem is that depending on which interface was added last into the bridge, I see arp requests coming FROM the bridge box on only one of them. Lets say I do:
#brctl addif br0 eth1
#brctl addif br0 eth2
and then ping 10.0.1.101 - I will see arp requests coming on br0 and eth2, but not on eth1 - obviously that is an issue - since I would expect bridge IP to be seen equally from both eth1 and eth2 sides - am I missing something? Is there a way to fix this?
Thanks

Yes. Just configure a static IP address instead of DHCP on the computer/device.
Linksys routers usually don't have any option to assign static IP addresses through DHCP. You have to configure it on the computer.

Similar Messages

HeuristicHazard within a transaction using only one DataSource

We have an ejb 2.0 application running under WL 7.0 SP1. Its CMP beans are
          persisted in two Oracle 9i databases, some beans from different databases
          are related (have CMR). We are using XA Oracle JDriver for both pools.
          The javax.transaction.HeuristicMixedException exception occurred when the
          client application called getId() method on the local interface of one of
          the beans. The client is a webapp deployed together with the ejbs in the one
          EAR.
          The mentioned bean doesn't have any CMR with any bean from the other
          database, and its transaction attribute is 'Required'. Therefore method call
          which resulted in HeuristicMixedException was using only one DataSource. Why
          did exception happened?


No.
There is a very slight increase in performance if you have two chips of the same size, but it is something that will only really show up in benchmarks.
Get 1GB now and leave the other 256MB chip in there. When you have an extra $80 around doing nothing, grab another stick.

VPLS (ATM-Ethernet) using only one circuit in the main ethernet site

Hi Everybody
We are needing to connect the following topology in our MPLS net:
The main site connects to the net through an Ethernet circuit and the remote sites are connected through ATM circuits. we need to use only one vlan in the main site. It is possible to connect this topoligy using only one vlan in the main site through VLPS? or pseudowires? which other solution can we use to solve this problem?
thanks a lot.

I understand your best option will be to run AToM/L2VPN internetworking and have a PVC from a remote locate to be "internetworked" to a sub-interfaces (representing a vlan) at the central site which have an Ethernet connection.
Take a look at this example:
http://www.cisco.com/en/US/docs/ios/wan/configuration/guide/wan_l2vpn_iwkg_ps6922_TSD_Products_Configuration_Guide_Chapter.html#wp1055162
HTH,
-W

HT204053 i RECENTLY PURCHASED ANOTHER IPHONE. MY INTERNET IS NOT WORKING. I JUST CREATED AN APPLE ID. WHAT'S NEXT? I NOW HAVE TWO DIFFERENT ACCOUNTS WITH DIFFERENT USER NAMES. HOW CAN I USE ONLY ONE ACCOUNT FOR ITUNES, ICLOUD APPLE ID ETC???

I RECENTLY PURCHASED ANOTHER IPHONE. MY INTERNET IS NOT WORKING. I JUST CREATED AN APPLE ID. WHAT'S NEXT? I NOW HAVE TWO DIFFERENT ACCOUNTS WITH DIFFERENT USER NAMES. HOW CAN I USE ONLY ONE ACCOUNT FOR ITUNES, ICLOUD APPLE ID ETC???

Welcome to the Apple community.
iTunes and iCloud and different accounts, you will need to delete both accounts from your device before adding the new details in their place.
For iCloud go to settings > iCloud, scroll down and hit the delete button. You can then sign back in using your correct details. For iTunes go to settings >store, tap your account ID and then sign out, you can then sign back in using your correct Apple ID.

Hi, If I have 1 license for creative cloud, will it possible to install in 2 computers (1 laptop and 1 desktop)? When I am in the office I can use desktop and at home I can use laptop? At the same time I will be using only one devise. Will that be possi

Hi, If I have 1 license for creative cloud, will it possible to install in 2 computers (1 laptop and 1 desktop)? When I am in the office I can use desktop and at home I can use laptop? At the same time I will be using only one devise. Will that be possible? Thanks

Yes. Yes. Yes.
Mylenium

Need to use only one sender and receiver communication channel.

Hello Experts.
I have a scenario where in I have to use only one sender and receiver communication channel to push files from different source directories to different receiver directories.
For Eg;
Sender
D://dir1/file1 --->                  E://dir1/File1
F://dir2/file2 ---->                 G://dir2/file2
H://dir3/file3----->                 I://dir3/file3.
Can this be achieved by using pass through scenario?
Please let me know if the requirement is not clear.
Thanks in advance.
Advit Ramesh

Hi Advit,
I think it is possible. You have to use the Advanced Selection for Source file in the sender channel to define multiple files to be picked up. Also, the Dynamic configuration must also be enabled and used in the mapping so you can manipulate the target directory and target file name based on your source files.
For Polling from multiple directories:
http://wiki.scn.sap.com/wiki/display/XI/File+Sender+Adapter+-+Polling+Multiple+Directories
Dynamic Configuration:
Dynamic file name and directory in Receiver File Adapter - summary of possibilities - Process Integration - SCN Wiki

I am using only one Apple ID. The problem, since iOS 6, is the App Store purchased items screen just shows loading screen it finally crashes or gives the error message 'can not connect to Apple store'

I am using only one Apple ID. The problem, since iOS 6, is the App Store purchased items screen just shows loading screen it finally crashes or gives the error message 'can not connect to Apple store'

I am using only one Apple ID. The problem, since iOS 6, is the App Store purchased items screen just shows loading screen it finally crashes or gives the error message 'can not connect to Apple store'

How do you use only one plugin in Logic for multiple guitar tracks? I want to only use one instance of Pod Farm and run all my guitar tracks through that one instance.

I want to be able to use only one instance of Pod Farm for my guitars, and have all of my guitar tracks run through it while I'm recording.

What he said. Or here is a similar approach with a picture.
1. Press the SEND button on every stereo (or mono) guitar track you want to send through the effect. Then select a free bus.
2. Make sure you turn up the amount of send (in db). Holding alt while leftclicking on this circle sets the send level to 0 db wich is good.
3. Open the mixer (Cmd+2). Please see that I here have turned the output off from the stereo guitar track. That way the only output will be the BUS, in your case the AmpTrack bus where all your guitars will pass through. If you want both the original guitar sound AND the Ampfarm effect then just set all outputs on your guitar tracks to Stereo Out, like the AmpF Bus track is set in my picture.
4. Insert your AmpFarm plugin here. I don´t have that plug so I inserted Waves Renes Axe for demo purpose.
Adjust the volume/effect of every guitartrack by turning the circle input shown as 2. in my picture.
I now see that you mentioned Pod Farm, not AmpFarm. But I guess it´s the same trick.
Have fun.
Heyclown.
Message was edited by: WizardSongs - Typhoos

Multiple Qaawses but use only one Qaaws at a time

Hi,
In Dashboard , I have two Qaawses (Qaaws1 and Qaaws2). When I am trying to generate SWF file both the qaawses are running. My requirement is, in Excel file I will set a flag value in one cell (0/1).
If the cell value is '0' then the Dashboard should use only Qaaws1.
If the cell value is '1' then the Dashboard should use only Qaaws2.
In essence my requirement is, even though multiple Qaawses are present in Dashboard, the Dashboard should be able to use only one Qaaws at a time based on my requirement (i.e., based on flag bit value 0/1).
Can any one suggest, solution for this?
Thanks in advance.
Regards,
M. N. Kishore Babu.

Hi David,
Thank you very much for the response and sorry for the delay.
Our actual scenario is a s follows:
We pass customer id and shipper Group Id as an input parameters to the flash variables from front end (through Java program). And these two values will written in Excel cells (let say Customer id in A1, and Shipper Group Id in B1)
Now there are two Qaawses, Qaaws1 and Qaaws2 in the xlf in addition to flash variables.
Qaaws 1 query is as follows :
select * from shp_details where customer id = A1
Qaaws 2 query is as follows :
select * from shp_details where customer id = A1 and ShipperGroup_id = B1
On front end we have two drop downs, Dropdown1 is for customer id and Dropdown2 is for Shipper Group Id.
When we select an item in Dropdown1, from front end we pass only Customer Id and when we select an item in Dropdown2, we pass both Customer Id and Shipper Group Id.
Our requirement is,
When we select Dropdown1 (we are passing only customer id), we expect only Qaaws1 to be executed.
When we select Dropdown2 (we are passing both customer id and shipper Group Id), we expect only Qaaws2 to be executed.
Please let me know, if I need to provide any further clarification.
Thanks & Regards,
M. N. Kishore Babu.

Parallelism in oracle using only one dual-core processor

Hi, is usefull or could i use parallel execution in oracle using only one dual core processor?
Can someone explain me why?

Hi
To take advantage of parallel processing you need enough resources (mainly CPU and I/O). If you run serially and the bottleneck is the CPU, then parallel processing might help. On the contrary, if the bottleneck is located in the I/O sub-system, throwing more CPU to it would not make things better. So, it's a question of balance between the CPU and I/O resources you have.
HTH
Chris

Is third-party SO/PO process possible using only one company code?

Hi friend,
1) my client wants to implement third-party PO process but also wants a way of keeping track of inventory during this process. I know that inventory should be tracked on the vendor side and not on our client side since we're doing third-party PO.
However my client wants to track inventory (in an inventory g/l account like 120100) so that when my client post a Goods Receipt, the inventory account
gets Debited and when client post the outgoing invoice to customer, the inventory account gets Credited. In this way, my client can track
if the customer have received the ordered item or not.
The problem is that third-party PO posts to consumption account but DOES NOT post to inventory account. Is there any way of
setting this up so that in addition to posting to comsumption account every time a Goods Receipt occurs?
2) i tried to create "Individual Purchase Order" (customer order from client -> client order from
vendor -> vendor ships item to client -> client then ships item to customer) so that posting will hit inventory account.
However, i find that taking this approach involves setting up a Plant for vendor (A), a Plant for our Client (B), and a Plant for Customer (C).
Because when i do a Goods Receipt, the stock has move from Plant A to Plant B. Then when i do a Goods Issue to the customer, it asks for the receiving plant. I assume this means that the stock moves from Plant B to Plant C.
Also, from the reading i did on the forum, i get the impression that i need to create more than one Company Code if i were to do
third-party PO. Do the Vendors have to be created in a different company code then the Customer? Or does it mean that Just the
plant (like Plant A) needs to be created in a different Company Code then Plant B and Plant C?
3) can i do third-party PO using only ONE company code?
Can anyone provide some clarification on this issue? I've read tons of posting but none really helped clear this issue up.
Thanks so much.

Dear Kishore,
Individual PO processing is not third party process at all. In third party process the vendor delivers the goods dirctly to the customer - please check what SAP help says.
http://help.sap.com/saphelp_46c/helpdata/en/dd/5601d4545a11d1a7020000e829fd11/content.htm
Dear Queyen,
One important point of third party process is that there's no need to keep stock of materials - that is in harmony with reality. Why does your customer want to keep stock from the goods if they doesn't receive at all? Is it coreect? It doesn't correspond to the fact.
You can do statistical (ghost) GR against the third-party PO and you can see the goods movement in MB51 - I think this should be enough.
http://help.sap.com/saphelp_46c/helpdata/en/dd/560287545a11d1a7020000e829fd11/frameset.htm
BR
Csaba

Color using only one CPU?

When rendering with Color it seams that it using only one CPU, according to "top".
Is it possible to make use of all CPUs?

Color's work is done on the GPU not the CPU, so unfortunately, the answer to your question is, no.

How do i confirm whether it is using only one partition.

I want to select the data from one partition only.
How do i confirm my select query using only one partition.
To front end developers how do i suugest to use correct partition.
I know in the select query we can write partion name also if i know the partition.
But i don't the correct partition name as a front end developer.

Hello,
You can find partitions for the table from following view user_tab_partitions. You can use PARTITION Clause but it defeats the purpose of having partition key column,
You should be able to do this
select * from my_part_table where part_key='key';Regards

Logic 8 using only one CPU while bouncing

Whenever I bounce a project, Logic 8 uses only one CPU. It also spikes this CPU completely, with the CPU meter going into the red area, which is why I am rather keen on persuading Logic to distribute the load.
Any ideas?
(I've given the support document with tips on how to balance multi-core performance a good read, but it doesn't seem to say anything on this particular subject, and following the advice in the document does nothing to change my CPU load.)

Bouncing is a single core process. Just like rendering is in Final Cut Pro. This won't change until Leopard and Apple's ProApps get better at handling multiple cores.
It's redlining because the processor core is working as fast as it can. Computer processors don't just randomly run slower, they use their resources for the tasks at hand. If it only used 50% of a core, the bounce would take twice as long to process.

Second mac in cluster uses only one core

Hello all. For some reason the second computer in my render farm is using only one core out of eight.
I'm using 2 Mac Pros linked together directly via giga ethernet wire. Mac one is a Quad Core 3ghz. Mac two is a Octo Core 2009 model. Both computers have the same version of FCS3 with different serial numbers.
In the Qmaster preferance pane: Mac one is set to "Quickcluster with services" with the check boxes for Share and Managed next to "Distributed processing for Compressor" checked. 4 instances selected and "Include unmanaged services from other computers" checked. Mac two is set to "Services only" with check box for Share next to "Distributed processing for Compressor" checked. 8 instances selected and "Include unmanaged services from other computers" checked.
I hit submit in Compressor, select the name of the cluster from Mac one, then in the Batch Monitor I see the video divied into 10 sections with Mac one handling 4 and Mac two handling one. On Mac two I see that the cores aren't fired up 100%, more like 30% on average.
I did a test earlier with a dual core mbp, and again only one core. How do I get my Octo core to use all 8 cores?

Solved the problem. The solution was simple, but somehow went under my radar. On Mac two in the Qmaster preferance pane next to the "Options for selected service" button, the selected service was set to off.
Duh

Bridge static IP using only one interface

Similar Messages

Maybe you are looking for