Broadband speed very slow.

I'm currently getting around half my broadband speed. I normally download at 140-160kb/s but for the last few days I've been getting 80kb/s max. The modems been on for a few days and it's still like this, and there are no problems in my area. Can you see any problems ?
speed test results:
1. Best Effort Test: -provides background information.
Download Speed
0.62 Mbps
0 Mbps
1 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.62 Mbps
For your connection, the acceptable range of speeds is 0.4 Mbps-1 Mbps.
IP Profile for your line is - 0.68 Mbps
These are my modem stats
Down Up
Modem Type:
Built in modem - ADSL
DSL Line (Wire Pair):
Line 1 (inner pair)
Current DSL Connection:
Rate:
768 kbs
448 kbs
Max Rate:
728 kbs
868 kbs
Noise Margin:
6.0 dB
19.0 dB
Attenuation:
54.9 dB
31.5 dB
Output Power:
15.0 dBm
12.3 dBm
Protocol:
G.DMT Annex A
Channel:
Interleaved
ATM PVC:
0/38
Rate Cap:
728 kbs
Attenuation @ 300kHz:
54.9 dB
Uncanceled Echo:
-17.1 dB
Ok
VCXO Frequency Offset:
28.5 ppm
Ok
Final Receive Gain:
32.9 dB
Ok
Excessive Impulse Noise:
0
Ok
Traffic StatisticsBytes Packets Errors %Cells Errors %
IP Traffic
Transmit:
60997578
218
0
0
Receive:
1546093739
1213140
0
0
ATM Traffic
Transmit:
2280542
0
0
Receive:
33112648
0
0
DSL Link ErrorsCollected for 19:32:46Reset 24-hr int. 15-min int. Last Event
Since
Current
Current
Time Since
ATM
Last Event
Cell Header Errors
147
147
0
0:04:41
Loss of cell Delineation
3
3
0
1:47:40
DSL
Link Retrains:
0
0
0
0:00:00
DSL Training Errors:
1
1
0
19:32:12
Training Timeouts:
0
0
0
0:00:00
Loss of Framing Failures:
0
0
0
0:00:00
Loss of Signal Failures:
0
0
0
0:00:00
Loss of Power Failures:
0
0
0
0:00:00
Loss of Margin Failures:
0
0
0
0:00:00
**bleep**. Seconds w/Errors:
154
154
0
0:04:41
**bleep**. Sec. w/Severe Errors:
0
0
0
0:00:00
Corrected Blocks:
67774
67774
3
0:00:15
Uncorrectable Blocks:
204
204
0
0:04:41
DSL Unavailable Seconds:
47
47
0
19:31:58

Hi Welcome to the forums
Here are some help pages done by CL Keith http://forumhelp.dyndns.info/speed/adslmenu.html
Can you also post the full results from BT Speedtest speedtester.bt.com
Have you tried connecting to the test socket at the rear of the master socket
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Similar Messages

Broadband speed very slow (again)

My broadband speed has been very slow for the past week or so, very hard to stream videos, download etc. Broadband download speed is normally around 7-8mbps mark and has been around 1-2 or lower this past week.
Speed test..
ADSL stats (I think a housemate must have reset the router 2 days ago)..
There are no problems reported at my local exchange.
I already had this same problem in January. It was fixed for a while but now it is really slow again.. https://community.bt.com/t5/ADSL-Copper-Broadband-Speed/Speed-way-way-down-on-normal/td-p/1149716

this is not the same as last time.. last time your speed was down at about 2mb wheras this time you have 11mb connection.
can you run btspeedtester again with wired connection and when first test completes then run diagnostic test and post results
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Broadband speed very slow and bt vision not workin...

As above my broadband speed has plummeted over the past couple of days which results in no on demand from my bt vision. have spoken to customer support and no joy there. I've changed the microfilter, unplugged router etc. and getting no where. Any help would be appreciated.
Solved!
Go to Solution.

FAQ
This Test comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
67 Kbps
0 Kbps
7150 Kbps
Max Achievable Speed
Download speedachieved during the test was - 67 Kbps
For your connection, the acceptable range of speeds is 600-7150 Kbps.
Additional Information:
Your DSL Connection Rate :8128 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 7150 Kbps
2. Assured Rate Test: -provides background information.
Download Speed
27 Kbps
0 Kbps
600 Kbps
Max Achievable Speed
Download speedachieved during the test was - 27 Kbps
For your connection, the acceptable range of speeds is 576-600 Kbps.
Additional Information:
Assured Rate IP profile on your line is - 600 Kbps
This test was not conclusive and further testing is required.This might be useful for your ISP to investigate the fault.

Unlimited broadband speed VERY slow (less than 25k...

When we first got setup around 6 weeks ago the broadband was fine but we had some noise on the phone line which we was told would settle down. - it did then got progressively worse and eventually the phone stopped working all together while the bt router continually lost connection to the broadband. After chasing BT for over 2 weeks we finally had an engineer out who found the phone line problem (previous engineer pinched two wires together causing it to burn out and short the circuit). we was told the broadband speed should pick back up after 3 or 4 days....today has been 5 days and doing a speedtest reveals my download speed to be (on average) 22kb/s with an upload speed of 15kb/s. Web pages take FOREVER to load and anything beyond text you may aswell give up waiting for. Just 6 weeks ago when shiny and new we was getting over 9mb/s - nothing changed internally the setup is all the same just the phone line issue.
Is there ANYTHING i can do to speed this process up? I'm quite put off after the experience i have had with BT services so far and the support have been hopeless.
Heres hoping someone has some ideas!

welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results .
are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

IOS7 wifi and LTE speed very slow.

iOS7 wifi and LTE speed very slow compared to iOS6. This was proven with Safari and using speed test app.

I have exactly the same problem symptom ever since installing iOS7. Toggling the FaceTime or the LTE settings alleviated the problem until I installed the latest version on IOS (7.0.4- 11B554a). Now the bug is permanent, a Network Reset will not work anymore, a System Reset will work only for the first execution of Speedtest.
Looks like the network software is throttling LTE speed to the minimum (.50 Mbps) up/download speed no matter what. Now unlimited Data means nothing, maybe AT&T wants me to go to Verizon or Tmobile.
I reported this problem to AT&T Sept 26 when I first installed IOS7, they told me there was no problem really that I needed to wait for the LTE network congestion to go away...? Since I found a circumvention by toggling LTE I did not pursued the problem...
After reporting the problem again this morning, they sent me to the AT&T store to change the SIM card.... I will try this and report back if it fixes the problem... Although I doubt it will fix anything but burn and extra hour of my day. The AT&T rep said that if the new SIM card doesn't fix the problem I need to go to Apple for them to give me a new Iphone....???? I guess there are many iPhones gone bad after installing IOS7 (sarcasm).
If you have this same problem, please post here so that I am able to get back to AT&T with some leverage to get them to remove the choking of LTE. Basically, if everyone accepts the new low speeds, then, unlimited data is no longer a problem for this phone company.

Upgraded to iMac - broadband now very slow

I'm hoping someone can help me here, as I'm really stuck on what the problem could be. I've recently upgraded from a Mac Mini to a 2008 20 Inch 2.4 GHz iMac. They were both on Snow Leopard, the upgrade went well and I used migration assistant to transfer across my files and settings.
Then I noticed that my broadband speed seemed slow. I thought this was probably just an ISP glitch, but today it was slow enough that I bothered to check more thoroughly - and it turns out it's the iMac that's slow. A broadband speed check I ran on my MacBook (1.83 GHz Core duo, so theoretically a slower machine in general) gave a result of over 10 Mbps. The iMac could only manage 1 Mbps. That's a tenfold difference! A check on iStumblr - again, with the machines right next to each other - shows a 10% difference in signal.
It's clearly not my wi-fi, or distance from the router (I have a full signal on the Airport icon, and I ran the speed test with my MacBook literally right next to my iMac). Could it be some settings that the iMac inherited from the Mac Mini, or does the iMac just basically have lousy wifi?
My office is too far from my router to realistically use a wired connection, so I'd really like to get this sorted if I can. Thanks for any help!

I've recently been having the same problem on my iMac as well. My MacBook Pro is testing much higher as far as broadband speeds. At one point, my iMac was running slower than dial up. I found that restarting temporarily improves speed, but lag often recurs. I have deleted the folder as described in the previous post and changed the channel on my router which has seemed to help. I was just wondering if anyone has any insight as to what might be going on with my iMac.

BT Broadband suddenly very slow on Mac OS X 10.5.8

Hello,
I'm posting on behalf of my dad as his broadband is now so slow as to be almost unusable. He lives in the Suffolk countryside but should still be able to receive broadband speeds of up to at least 1.5mb/s on his local exchange. His BT broadband service has never been brilliant but has recently slowed right down. He has an iMac 2.66 Ghz Intel Core 2 Duo running OS X 10.5.8. He has tried upgrading to a BT Home 3.0 router but this has not improved his broadband speed. I have tried to run the BT speedtester but I can't get it to work because it says Java is not installed despite it appearing to be enabled as a plugin. I have tried this in both Safari and Firefox. I have asked him to try the speedtester available on the uSwitch website which has recorded a download speed of only 0.2 and upload of 0.1mb/s. I would be very greatful if anyone has any suggestions as I am going to visit him tomorrow. I intend to try plugging the hub directly into the main socket via a microfilter. I also plan to try upgrading his operating system to snow leopard but I doubt that this will improve his connection. The quality of the phone line seems to have decreased recently too. Is my only option to try ringing BT customer services?
Thank-you!

Hello,
Have upgraded to Mac OS X 10.6.3 and now able to run BT speedtester:
Also here are hub stats:
Ran Uswitch speed tester again:
This suggests that we should be able to get up to 2.5Mb on this exchange.
Have tried quiet line test, line is not silent, there is low level interference on wire connected handset. Have tried connecting hub directly to master socket which has given a slight improvement in performance but still to my mind unacceptably slow. Could not repeat BT speedtest as limited to one test per hour. Ran Uswitch test again:
I know that he has just changed from Hub 2 to Hub 3 and it will take time to settle but broadband speed had already declined notably (to the point of being barely usable) on Hub2 before switching to Hub3.
Any further advice gratefully received....

Internet speeds very slow.

Found web browsing very slow this morning. Checked my World of Warcraft account and that was also running slow.
Did a speed test and got these results.
Download Speed
0.42 Mbps
0 Mbps
4 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.42 Mbps
For your connection, the acceptable range of speeds is 1.2 Mbps-4 Mbps.
IP Profile for your line is - 2.79 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.02 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Checked the service status and there is no problems in my area
Any help please.

It is a wired Connection
Help
My broadband connection
Your broadband line is connected.
Broadband connection details:
Downstream
3,167 Kbps
Upstream
34 Kbps
Connection time
0 days, 2:13:38
Data transmitted
9.31 MB
Data received
34.88 MB
Broadband user name
[email protected]
My telephones
Current settings for the telephones and handsets connected to your BT Home Hub.
Calls to:
Will ring:
Status:
My landline
None of the Hub Phones
There is no Broadband Talk account associated with your Home Hub.
To activate your Broadband Talk account click here
To view or change settings click here
My home network
Devices connected to your BT Home Hub.
Wireless:
android-19f677c5fe397e11
Wireless:
BenHarrison-HP
Wireless:
Wii
Ethernet:
Marcus-PC
USB:
No devices detected
BTSpeedtester Beta (taken from http://speedtest.btcentralplus.com/beta/)
Download Speed 0.63
Upload Speed 0
Ping149.63

Broadband is very slow and unusable!

For the last 2 nights running my connection is running very slow to the piont the BBC website or a youtube video fails to load. Ps3 gaming is impossible! Have rung BT India and gone though all they do with resets and whatnots and still stuck at square one wih no improvement.
My connection is option 3, 20mb home broadband and have been with BT broadband for 7 years with good service.
My stats below.
Line Mode
ADSL2+
Line State
Show Time
Line Power State
L0
Line Up Time
01:02:07:06
Line Coding
Trellis On
Line Up Count
1
Statistics
Downstream
Upstream
Line Rate
11421 Kbps
1069 Kbps
Noise Margin
3.1 dB
6.8 dB
Line Attenuation
42.5 dB
21.3 dB
Output Power
0.0 dBm
13.0 dBm
These above have been these figures for the last 12 months and have had no problems at all.
Speedtester refuses to test my speed saying there is an error at this time but using other speedtesters im only getting between 150-200kb download speed but getting my normal 902kb upload. Usually my speed is always about 9000-10000kb.
Is there a problem in the 0208 Essex area as two of my friends withing a mile away have the same broadband package as me also have the same speed problem??
Solved!
Go to Solution.

Hi there have been service outages and degraded service issusein London and the south east today I would suggest reseting your hub tomorrow morning and recheck the Bt speedtest and then posting the results back here we can then offer further advice
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Broadband Always Very Slow

My broadband has always been very slow since we moved into our house 3 years agao. I had hoped it would improve through time but to no avail.
We are in a rural location which I am guessing is the problem but it is very frustrating. We cannot even stream audio files.
Is there anything we can do and I dont mean all the usual stuff we have tried all that and had a line spun to us from BT that they were doing things to help.

welcome to the BT community forum where customers help customers and only BT employees are the forum mods
this may be the usual stuff again but in order for the forum members to help please can you post the adsl stats from your router you may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Speed very slow for last 3 days or so.....121kbps ...

M speed is usually 1.5mb been down to about 300 the last few days and dipped now at 121 and just a measly 97 this morning....
done all the usual checks, and i noticed on a local internet forum last night that other is my area are suffering the same too with no explanation from BT
(my daling code is 01595)
phoned BT...he said there were no faults it must be my end, repeated all the checks including the microfilter, he then said there WAS a problem with outtage and it would be 8 days before my speed was returned to normal....when i questioned this he explained it was cos of a powercut somewhere in the UK for 4 hours?????eh?
he then went on to quiz me if i had selected 1 when i phoned to leave feedback, when i said i had he seemed quite aggitated, quized me more about selecting to leave feedback and told me this effected his performance.
he then told me not to phone BT again for the next 10 days as this would confuse people and it would be an extra week on top of the 8 days i would have to wait for my normal broadband speed.
i am obviously totally disatisfied...i just want to know why my speed is slow and when it will return to normal
anyone help.???
my dailing code is not on any of the service status pages

is this what you mean
DSL Connection
Link Information
Uptime:
0 days, 4:10:58
Modulation:
G.992.1 annex A
Bandwidth (Up/Down) [kbps/kbps]:
448 / 448
Data Transferred (Sent/Received) [MB/MB]:
5.39 / 39.37
Output Power (Up/Down) [dBm]:
12.0 / 14.5
Line Attenuation (Up/Down) [dB]:
31.5 / 63.0
SN Margin (Up/Down) [dB]:
12.0 / 16.5
Vendor ID (Local/Remote):
TMMB / P
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
70 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
450 / 0
FEC Errors (Up/Down):
0 / 421,367
CRC Errors (Up/Down):
0 / 11,336
HEC Errors (Up/Down):
0 / 6,718
Line Profile:
Interleaved
i phoned BT again, spent 2 hours on the phone!!! we went through the usual checks etc, this time they
tested the line properly and confirmed they could see i had very slow speed, but couldn't tell me why?
they said they would reset the line and i should see an improvement in 24 to 48 hours and it should return to usual in 8 day?? i still dont understand.....
and its still as slow as 112kbps..as me and partner both rely on internet for our work and training its just painful waiting for this to be solved!!
i just want a clear explantion what is happening/why its happening and when will it be fixed?

[SOLVED] Network speed very slow, no apparent reason

Hello, recently I switched from Windows 7 RC1 to Arch on my home machine (I have used Gentoo, Ubuntu, and Fedora 10 on the same machine in the past), and for some reason network speed is very slow.
I have Verizon's 20mbit/5mbit package, and I have always gotten that speed.
Using speedtest.net and 100mb.test from cachefly on multiple computers I have come to the conclusion that it is infact my Arch install that is causing the problem:
- All other machines on my network are getting 20/5 (both wired and wireless)
- I ran a speedtest from 2 other machines using the ethernet cable that this PC is on. Again, full 20/5.
- scp transfer of 100mb.test from this PC -> other Arch box: ~2.8MB/s.
- scp transfer of 100mb.test from other Arch box -> this PC: ~2.8MB/s.
- scp transfer of 100mb.test from this PC -> UK VPS (100mbit line): ~539KB/s
- scp transfer of 100mb.test from UK VPS -> this PC: ~76KB/s
- scp transfer of 100mb.test from this PC -> Chicago Server (dual gbit lines): ~563KB/s
- scp transfer of 100mb.test from Chicago Server -> this PC: ~91KB/s
speedtest.net result:
Upload speed seems to be unaffected.
I have tried disabling TCP window scaling, and appending my hostname to /etc/hosts.
What is weird though is that the other Arch box has an identical network config, I don't see any reason why it shouldn't work.
My NIC is an integrated Realtek something, I can get the exact model if needed.
Last edited by whipsch (2009-06-05 18:29:21)

Hi, whipsch
Can you try ethtool to see if your ethernet card is actually negociating and using a 100Mb full duplex link on your LAN ? If not you can try to force the link parameter with ethtool. Also maybe the driver of your NIc has options related to link negociation.
Hope this helps,
JF

Mac App Store download speed very slow...

I have been trying to download the App Store updates OS X Update 10.10.3 and OS X Yosemite Recovery Update to my iMac for the past several days. When opening the Mac App Store, I click on updates and they appear. However, when I select 'download' my download speed slows to the point of less than 1 MB per minute.
I seem to remember this happening when Yosemite was first released, but after a few days, I had no problem downloading Yosemite from the App Store.
This only occurs when trying to download from the Mac App Store. When I download iOS App updates to iTunes I do not have the same problem so it seems to be only affecting the Mac App Store.
My internet speed is fine. I can download fine from other websites, just not the Mac App Store.
After searching online, I found one solution that looked promising:
Finder->Applications->Utilities->Keychain Access->Preferences->Certificates->Certificate Revocation List- Changed from Best attempt to OFF.
Unfortunately for me this had no effect so I changed the setting back.
I then looked for a way I could download the files from outside the Mac App Store & found this:
Apple - Support - Downloads
When downloading from Apple Support downloads page, my downloads were very fast. The Yosemite 2 GB Combo update took about 15 minutes, a far cry from the App Store which would have taken hours.
Is there some setting I need to change to increase the download speed from the Mac App Store or is it just overloaded servers? Why then can I download the files from the support page and not run into the same slow speeds? Updating iTunes was also giving me very slow download speeds, so again, I went to the Apple Support Downloads & clicked the link to download the latest version of iTunes. The file downloaded in about a minute.
Any suggestions would be appreciated.
Thanks!

Apple servers are overloaded. Instead of using App Store, use safari to download the updates manually from apple websites.
Here's a link for OS X 10.10.2 Combo Update.
OS X Yosemite 10.10.2 Combo Update
I had the same issue and downloaded manually from this link. It took me about 30-40 minutes. I'm using a 5mb connection. Your 40mb connection should be faster.
As for the iOS updates, you will have to download them from your iOS devices, because there are no standalone updates for iOS. Alternatively after you update your Mac, use iTunes to download iOS updates by connecting your iOS devices with your Mac. That should be faster than downloading through your iOS devices.

Internal Disk to Disk Data Transfer Speed Very Slow

I have a G5 Xserve running Tiger with all updates applied that has recently started experiencing very slow Drive to Drive Data transfer speeds.
When transferring data from one drive to another ( Internal to Internal, Internal to USB, Internal, Internal to FW, USB to USB or any other combination of the three ) we only are getting about 2GB / hr transfer speeds.
I initially thought the internal drive was going bad. I tested the drive and found some minor header issues etc... that were able to be repaired so I replace the internal boot drive
I tested and immediately got the same issue.
I also tried booting from a FW drive and I got the same issue.
If I connect to the server over the ethernet network, I get what I would expect to be typical data transfer rates of about 20GB+ / hr. Much higher than the internal rates and I am copying data from the same internal drives so I really don't think the drive is the issue.
I called AppleCare and discussed the issue with them. They said it sounded like a controller issue so I purchased a replacement MLB from them. After replacing the drive data transfer speeds jumped back to normal for about a day maybe two.
Now we are back to experiencing slow data transfer speeds internally ( 2GB / hr ) and normal transfer speeds ( 20GB+ / hr ) over the network.
Any ideas on what might be causing the problem would be appreciated

As suggested, do check for other I/O load on the spindles. And check for general system load.
I don't know of a good GUI in-built I/O monitor here (and particularly for Tiger Server), though there is iopending and DTrace and Apple-provided [performance scripts|http://support.apple.com/kb/HT1992] with Leopard and Leopard Server. top would show you busy processes.
Also look for memory errors and memory constraints and check for anything interesting in the contents of the system logs.
The next spot after the controllers (and it's usually my first "hardware" stop for these sorts of cases, and usually before swapping the motherboard) are the disks that are involved, and whatever widgets are in the PCI slots. Loose cables, bad cables, and spindle-swaps. Yes, disks can sometimes slow down like this, and that's not usually a Good Thing. I know you think this isn't the disks, but that's one of the remaining common hardware factors. And don't presume any SMART disk monitoring has predictive value; SMART can miss a number of these cases.
(Sometimes you have to use the classic "field service" technique of swapping parts and of shutting down software pieces until the problem goes away. Then work from there.)
And the other question is around how much time and effort should be spent on this Xserve G5 box; whether you're now in the market for a replacement G5 box or a newer Intel Xserve box as a more cost-effective solution.
(How current and how reliable is your disk archive?)

New broadband connection - very slow- please help

Hi,
On 3rd of May (last Thur) I got my new phone and broadband installed. My broadband speed is soo slow that I have to buy internet dongle to get back onto proper internet.
I know about 10 days stabilization period- phoned to India couple of times and being told after 10 days I will get a better normal connection. I just dont belive that. Today is 8th day of 10days waiting and there is no changes at all! I need internet for my uni.
Please can sameone help me? any advice?
thank u in advance
1) I am connected to the master socket. I've tried to connect to test socket but things weren/t going improve.
2) Tried wireless connection and used ethernet cable. For both connections the broadband is slow.
3) Done the quiet line test- no faults.
4)
ADSL Line Status
Connection Information
Line state:   Connected
Connection time:   0 days, 01:19:22
Downstream:   5.555 Mbps
Upstream:   800 Kbps
ADSL Settings
VPI/VCI:   0/38
Type:   PPPoA
Modulation:   G.992.5 Annex A
Latency type:   Fast
Noise margin (Down/Up):   6.5 dB / 5.7 dB
Line attenuation (Down/Up):   47.4 dB / 29.5 dB
Output power (Down/Up):   20.0 dBm / 12.8 dBm
FEC Events (Down/Up):   0 / 0
CRC Events (Down/Up):   78942 / 306
Software version 4.7.5.1.83.8.57.1.3 (Type A) | Time and date 20:34 11/05/12
5)Beta speedtest
download speed: 0,32
upload speed: 0,63
Ping Latency: 37,88

Here are some help pages done by CL Keith http://www.btinternet.com/~cbeddoe/speed/Speed.html
also post your full hub stats details shown in this link http://www.btinternet.com/~cbeddoe/others/adslstats.html
Have you tried connecting to the test socket at the rear of the master socket
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Broadband speed very slow.

Similar Messages

Maybe you are looking for