Broadcast/multicast counters does not increase on vlan interface

Hi,
on a Cat6500 we try to monitor interface packet statistics via snmp, in detail we want to get information about the relation between unicast, multicast and broadcast packet counter.
What we found out is that while on physical l2 interfaces all counters (ifHCInUcastPkts, ifHCInMulticastPkts, fHCInBroadcastPkts, ifHCOutUcastPkts, ifHCOutMulticastPkts, ifHCOutBroadcastPkts) are filled, on vlan interfaces multicast in/out and broadcast out packets stay zero whole the time. We use arp, hsrp, ospf and other well know broadcast and multicast based protocols.
Does anybody know why this counters do not increase?
Attached you find an excel sheet which shows an example of interface counter vs. vlan counter.
many thanks in advance,
Thorsten Steffen

Hi jon,
belown the result of sh sdm prefer,so need i a licence ip service to apply the route-maap on the interface vlan,or just entrer the config"sdm prefer routing" and reboot the switch?
SWBB0#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.
number of unicast mac addresses:                  6K
number of IPv4 IGMP groups + multicast routes:    1K
number of IPv4 unicast routes:                    8K
    number of directly-connected IPv4 hosts:        6K
    number of indirect IPv4 routes:                 2K
number of IPv6 multicast groups:                  64
number of directly-connected IPv6 addresses:      74
number of indirect IPv6 unicast routes:           32
number of IPv4 policy based routing aces:         0
number of IPv4/MAC qos aces:                      0.5K
number of IPv4/MAC security aces:                 0.875k
number of IPv6 policy based routing aces:         0
number of IPv6 qos aces:                          0
number of IPv6 security aces:                     60

Similar Messages

Importing classes does not increases SWF size

Hi, there!
I was doing tests, and realized that the some classes of AS3
does not increases the size of the SWFs. In AS2 UIComponent class,
for sample, the SWF increases 4 kbytes importing this class
(UIComponent).
So, I ask you: which classes does increase files size?
Thank you in advance.
CaioToOn!

Hi, Andrei!
I've already tested instancing then. And the SWF file became
636 BYTES, not even 1 Kb. I believe that this size (636 bytes) are
only about the bytes of the characters of the Class. Look the code
below:
package
import flash.display.MovieClip;
import flash.filters.BevelFilter;
import flash.filters.BlurFilter;
import flash.filters.ColorMatrixFilter;
import flash.filters.DropShadowFilter;
import flash.display.Loader;
import flash.filters.GlowFilter;
import flash.text.TextField;
public class Main extends MovieClip
private var e:BlurFilter;
private var e1:DropShadowFilter;
private var e2:TextField;
private var e3:GlowFilter;
private var e4:BevelFilter;
private var e5:ColorMatrixFilter;
private var load:Loader;
public function Main()
load = new Loader();
e = new BlurFilter();
e1 = new DropShadowFilter();
e3 = new GlowFilter();
e4 = new BevelFilter();
e5 = new ColorMatrixFilter();
te.filters = [e, e1, e3, e4, e5];
e2 = new TextField();
e2.text = "CaioToOn!";
addChild(e2);
It really don't increases the file size. Only because of the
extra characters.
CaioToOn!

CPU heats up on file copy/backup and fan speed does not increase

Hi Friends,
I have been having issues with fan in my Dell Studio 1555. It has an ATI Radeon card and I had installed the proprietary catalyst driver as the open source driver is too noisy.
Recently, I noticed that on accessing my hard disk and copy files or running backup (luckybackup), the temperature shoots up from around 60 deg C (just using chrome) to 100 deg C when it would shut down itself. However, it seems like the fan speed does not increase with the increase in temperature to help it cool down.
I tried to get the fan speed details with "lm-sensors" but it would not show the fan speed. Here is the output of sensors:
[user@domain]$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +60.0°C (crit = +100.0°C)
temp2: +59.0°C (crit = +100.0°C)
temp3: +66.0°C (crit = +100.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +58.0°C (high = +105.0°C, crit = +105.0°C)
Core 1: +58.0°C (high = +105.0°C, crit = +105.0°C)
Following the Arch wiki, I added acpi_enforce_resources=lax to kernel parameters but it did not help as well.
Here is the main problem:
1. CPU temperature shoots on accessing hard drive but fan speed does not increase - Any guide/direction to investigate would be really helpful.
2. Sensors does not show the fan speed. Read about i8kutils, but couldn't figure out how to get it working with systemd. Any indicators here?
Last edited by ravisghosh (2013-07-01 05:22:01)

luuuciano wrote:Ravi, did you solved it?
Im having similar issue on a vostro 1710, fan never works... :-/
The fan was bad. I had to replace the fan. However, I have not been able to figure out how to see fan speed in sensors.
Last edited by ravisghosh (2013-09-08 15:57:37)

I delete files but my available disk space does not increase

I delete files but my available disk space does not increase. What to do?

Try reindexing the hard drive:
http://support.apple.com/kb/ht2409

When i delete files memory does not increase

When I delete files from the memory the size of available memory does not increase. Why?

Try restarting the computer, then select the disk's Desktop icon. Press COMMAND-I to open the Get Info window and check how much free space is shown. If it still hasn't changed at all then try the following:
Repair the Hard Drive and Permissions - Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Although the suggestion to delete old Time Machine snapshots, if any, that will only free up space but will not fix the problem you have described. If you are deleting files but the free space on the drive fails to update, that means there is a directory problem on the drive that needs to be fixed.

Does not implement the NamespaceHandler interface

I depoly a war file and get following errors. This project does not contain jar files related with spring.
BUILD FAILED
weblogic.Deployer$DeployerException: weblogic.deploy.api.tools.deployer.DeployerException: Task 0 failed: [Deployer:149026]deploy application smap.war on AdminServer.
Target state: deploy failed on Server AdminServer
java.lang.IllegalArgumentException: Class [org.springframework.scripting.config.LangNamespaceHandler] does not implement the NamespaceHandler interface
     at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.initHandlerMappings(DefaultNamespaceHandlerResolver.java:119)
     at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.<init>(DefaultNamespaceHandlerResolver.java:96)
     at org.springframework.beans.factory.xml.DefaultNamespaceHandlerResolver.<init>(DefaultNamespaceHandlerResolver.java:83)
     at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createDefaultNamespaceHandlerResolver(XmlBeanDefinitionReader.java:498)
     at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.createReaderContext(XmlBeanDefinitionReader.java:487)
     at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.registerBeanDefinitions(XmlBeanDefinitionReader.java:468)
     at org.springframework.beans.factory.xml.XmlBeanDefinitionReader.doLoadBeanDefinitions(XmlBeanDefinitionReader.java:363)

Hi,
I am not sure - given the information you provide - that you posted to the right forum
Frank

"photos" option does not appear in my interface. Do have Music, Movies, TV Shows, Apps and Radio. Photo doesn't appear on iPhone or iPod Nano

"PHOTOS" option does not appear in my interface. Do have Music, Movies, TV Shows, Apps and Radio. Photo doesn't appear on iPhone or iPod Nano

Are you looking at the tabs on the right-hand side of iTunes when you've connected and selected your device on the left-hand side of iTunes ? i.e. it should be one of the tabs that you use to chose what content to sync to the device : syncing photos

1240 AP does not honor native vlan diffent then 1

Hi,
I stumple with a cracy issue and hope someone have an idea what is going wrong.
I have an older 1240 Autonomous AP where I cannot figure out why the device is using vlan1 instead the required vlan 1616 for management traffic.
Anyway clients can connect, getting IP adresses and traffic is routed but the ap can be managed only via serial console cable or temp. by configuring
the port on the 3750 from trunk to an access port.
1240 config.
version 12.4
hostname ap
dot11 mbssid
dot11 ssid vlan1621
   vlan 1621
dot11 ssid vlan1630
   vlan 1630
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1621 mode ciphers aes-ccm
encryption vlan 1630 mode ciphers aes-ccm tkip
ssid vlan1621
ssid vlan1630
station-role root
no cdp enable
interface Dot11Radio0.21
encapsulation dot1Q 1621
no ip route-cache
bridge-group 21
interface Dot11Radio0.30
encapsulation dot1Q 1630
no ip route-cache
bridge-group 30
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.16
encapsulation dot1Q 1616 native
no ip route-cache
bridge-group 1
interface FastEthernet0.21
encapsulation dot1Q 1621
no ip route-cache
bridge-group 21
interface FastEthernet0.30
encapsulation dot1Q 1630
no ip route-cache
bridge-group 30
interface BVI1
ip address 192.168.16.11 255.255.255.0
ip helper-address 192.168.18.20
no ip route-cache
ip default-gateway 192.168.16.1
bridge 1 route ip
3750g config:
interface GigabitEthernet1/0/39
switchport trunk encapsulation dot1q
switchport trunk native vlan 1616
switchport trunk allowed vlan 1616-1630
switchport mode trunk
switchport nonegotiate
Changing the bridge-group on the fa0.16 subinterface from 1 to anything different was also without success.
tested 1240 firmware: c1240-k9w7- 123-8.JA2 / 124-25d.JA1 / 124-25d.JA2

Hi
I have applied your config onto 1252 AP directly connect to 3560 switch as shown below & config works as expected.
+++++++ Switch Config ++++++
vlan 1616,1621,1630
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 1616
switchport trunk allowed vlan 1616-1630
switchport mode trunk
interface Vlan1616
ip address 192.168.16.1 255.255.255.0
++++++++++ AP Config ++++++++++
dot11 ssid vlan1621
vlan 1621
dot11 ssid vlan1630
vlan 1630
interface Dot11Radio0
encryption vlan 1621 mode ciphers aes-ccm
encryption vlan 1630 mode ciphers aes-ccm tkip
ssid vlan1621
ssid vlan1630
interface Dot11Radio0.21
encapsulation dot1Q 1621
bridge-group 21
interface Dot11Radio0.30
encapsulation dot1Q 1630
bridge-group 30
interface GigabitEthernet0.16
encapsulation dot1Q 1616 native
bridge-group 1
interface GigabitEthernet0.21
encapsulation dot1Q 1621
bridge-group 21
interface GigabitEthernet0.30
encapsulation dot1Q 1630
bridge-group 30
interface BVI1
ip address 192.168.16.11 255.255.255.0
ip default-gateway 192.168.16.1
AAP1#ping 192.168.16.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.16.1, timeout is 2 seconds:
If it does not work for you, I would check vlan 1616 is available in all your switches upto where SVI for vlan 1616 defined.
In your case interface vlan 1616 defined on AP directly connected switch ?
HTH
Rasika
**** Pls rate all useful resposnes ****

Play Count does not increase

Hey everyone...I've notice recently that when I have my iTouch connected to the computer and play a song the play count will increase, but if I'm just listening to it and then plug it back in, the play count has not increased. I listen to the songs in full, so I don't know why they won't increase in play count. Any ideas?

i realise why Apple has changed this behavior....
http://support.apple.com/kb/ht1202
Now you can add music on multiple computers! (support page updated after iOS 5 introduction), thus playcount is no longer working when you are in Manually Manage Music mode... but instead of tracking individual libraries, they just kept it indepedent... and break the feature.
Apple should've explained this... i lost some good playcount on my songs

Credit Memo Does Not Increase Inventory

Dear Experts,
I have created a new Credit Memo and the associated inventory is not being increased as usual.
I have checked all the root documents - sales order and AR Invoice and delivery, they are all closed.
I am using the Extended Warehouse add-on, which displays all my inventory, and usually the inventory is returned / increased after positing the Credit Memo.
Any ideas?
Thank you,
Justice

hi
please clarify ur question as at the staring of the question u sates that Credit memo is not increasing the warehouse inventory whereas towards the last u have indicted that the inventory in the warehouse is being getting effected
So would request you please reform ur question however as per the standard practice when we make A/R credit memo then the quantity in our warehouse should increase.
However please state that the in the A/R invoice documnet the warehouse u have selected is same as the warehouse in the A/R invoice document
Regards,
Manish

File's Owner does not show methods in Interface Builder 3.2.6 but the class is set correctly and the nib on the lower left is green

Hi, I'm trying to make my first IPhone app. After having problems with interface builder the first time I coppied the code directly from a tutorial in case I made any mistakes. I saved the program, and re-opened the .xib file. Right clicking File's Owner does not show a list of methods. I've been looking around for solutions for this but have not gotten anything to work. I tried deleting the default .xib and creating a new one through file-> new file. This did not help. I did notice that File's owner was showing up as a light blue cube apposed to a yellow one now and found that a bit odd but otherwise nothing changed. I opened the library menu and selected helloWorldiPhoneViewController so it would show up in the view port. I set the class field of File's Owner to hellowWorldiPhoneViewController. File's Owner still does not show methods when right clicked or when a line is dragged over a button. I read somewhere that the color of nib on the lower left of the viewport may indicate a problem, but it is green not indicating any issue. Every solution I found for someone else seems nto to work for me and I don't know how to continue.
here is the .h file just in case:
// HelloWorldViewController.h
// HelloWorld
// Created by Paul Peelen on 2011-03-14.
// Copyright 2011 9697271014. All rights reserved.
#import <UIKit/UIKit.h>
@interface HelloWorldViewController : UIViewController {
UILabel *textLabel;
@property (nonatomic, retain) IBOutlet UILabel *textLabel;
- (IBAction)changeTheTextOfTheLabel;
@end
I'm trying to connect changeTheTextOfTheLabel to a button and textLabel to a label

You need a parameter for an interface builder method. The type should be id and the name is typically "sender". It would look like this:
- (IBAction)changeTheTextOfTheLabel: (id) sender;
Be careful about those tutorials. Many are ancient and do not correspond to current Xcode behaviour.

Field added to cobl does not appear in FB01 interface

Hi!
I have added OXK3 transaction and set this field as "Opt Entry", but the field does not appear in FB01 transaction.
I've also tried "Req Entry" status for new field it gave no effect.
How this field can be enabled in the interface of standard FI transactions?
Thanks!

Some questions
-Did you solve your problem ?
-Did you come through OSS <a href="https://service.sap.com/sap/support/notes/174413">Note 174413 - Customer-specific fields in new Enjoy transactions</a> ?
Regards

Report Engine does not increase when there is a large no of reports queue

Hello Everybody,
Specifications:
Product : Oracle Application Server Forms and Reports Services 10.1.2.0.2
OS : Windows 2003 R2 Server
Dual Core CPU 2600MHz
6 GB RAM
We are doing the sizing for our reports server. We have specified the following in our rep_server.conf
<engine id="rwEng" class="oracle.reports.engine.EngineImpl" initEngine="2" maxEngine="6" minEngine="2" engLife="50" maxIdle="30" callbackTimeOut="90000" engineResponseTimeOut="3" jvmoptions="-Xms64m -Xmx128m">
Even when there are 5000 or more reports in the queue still the number of engines in the reports server remains at 2 though I have given that it can use upto a maximum of 6 engines. Can anybody please explain why this happens? Am I missing something here?
Thank you for your reply in advance.

Hello,
Anybody has any idea why the report engine is behaving like this?
Thanks in advance

"apple-+" does not increase font size in preview pane in mail.app 4.2

i have letterbox http://harnly.net/2009/software/letterbox/letterbox-beta-4-for-snow-leopard/ installed on my machine. before the SL upgrade, i could hit cmd-+ and increase the font size of the message i am viewing. that was super convenient!
i can't do it any more. any ideas anybody on how to bring that back? btw, if i open a separate window for the message, i can use cmd-+ to increase font size. but no more can i use it in the preview window.

the obvious suspect would be letterbox. it's beta (=bugs) and I've also heard report that it's incompatible with 10.6.2. you can try uninstalling it and see if that fixes the issue.

File deletion does not increase space available in CC

I did an experiment this morning to see what was going on with my space utilization being incorrect.
1) I added about 5GB of files and folders to my local CC Files folder
2) Sync worked properly, my utilized space went from about 5GB to about 10GB
3) I deleted 5GB of files and folders from my local CC Files folder
4) Sync worked properly, and all 5GB of files and folders were archived in CC
5) From the website interface, I deleted all 5GB of files and folders from the archive
6) My archive showed as empty via the web interface
7) My files and folders on the CC web interface matched the contents of my local CC Files Folder
8) My CC space utilized, according to the web interface, only dropped from 10GB to 9.2GB, but the actual utilization should be a little over 4.9GB.
I suspect this is happening to everyone and will get worse with time. Adobe - please address.

The steps you describe don't replicate the effect here, I've tried it several times on three workstations. At step 4 the usage remains allocated (as it should, given the files are in the archive folder) but as soon as the archive is permanently deleted, usage in both the web portal and CCDA falls to 0%. Within seconds.
If it's not reducing in your case, then the files aren't being deleted. They may not show up, but that's a different problem to the idea that deleting a file doesn't reset the usage.

Broadcast/multicast counters does not increase on vlan interface

Similar Messages

Maybe you are looking for