Broadcom BCM94311MCG wlan wireless range problems 'ndiswrapper'

Hello masters of ArchLinux
I have a little issue with my Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01) wireless adapter using ndiswrapper ,configured step by step following the
http://wiki.archlinux.org/index.php/Wireless#BCM43XX wiki page
At the beginning i was very confused ,becouse with my 3 year expirience with Linux I was unable to understood what is happening with my wireless ...
Under ArchLinux using ndiswrapper my wireless adapter has only 3 meters of range with any type of access point ,even with ad-hoc...I tried with D-link AP, Linksys & etc...
The first thing that was up to my head was the 'Transmit Power' on the adapter , 18 mw...But then I restart under WindowsXP also on the same notebook ...Dell inspiron 1501...the transmit power was also 18 mw ,but my wireless was working with very good range ,above 300 meters from the AP
Any suggestions about this issue ?

Try the kernel's b43 module.

Similar Messages

  • WRE54G wireless range problems.

    God day, dear experienced user.
    Ok, here is my story:
    I got two houses on my property, and house A got an AP modem called ZyXEL. Which is based on the standard 802.11G.
    This Access Point is in House A.
    I have moved some of my childrens to House B. And they want to have an Internet connection over there. 
    House B is pretty close house A. So  they get a weak signal strenght from our ZyXEL modem wireless AP. But they want to make it stronger.
    We located a window in house B with 1, 2 "lines of strenght". However the other locations in House B the signal strenght is 0, 1 line. 
    We bought a Wireless - G Range Expander, model: WRE54G. Version 3 I believe. And we located it at the window with 2 signal strenght. Plugged in the power supply.
    Then I tried to connect to it, it did not work.
    Then I readed forums regarding other users with same situation, it looks like it was something with password encryption. 
    Then I entered the gateway of the main AP, which is 10.0.0.138. And I changed it from WPA PSK to "unsecured". 
    Then on House B where the Range Expander is located I clicked a button for auto configuration.
    Well the situation is: The name of the range expander seem to have changed to the name of our Wireless AP ESSID. So I thought it worked, also, inside House B, we got like 4 to 5 lines of signal strenght. And thought Wohoo! Its working!
    But then, we connect to it, and it seems we can not get an properly connection to the internet.
    After some further investigations, we cant connect to the gateway either. Even thought it says we are connected.
    Here is my testing: 
    I connect to the network, which is usually 0, 1 line, but now 4, 5. 
    Then the "connecting" icon changes to the normal icon which at least usually represents "connection working". 
    Then I enter command prompth. 
    I write IPCONFIG. And I find out that the gateway is 10.0.0.138, and that my IP is 10.0.0.4
    BUT, then I write "PING 10.0.0.138".
    And I get NO response.
    Note that I got my firewall disabled, the router's firewall is also disabled, and it is "unsecured" mode, it has no encryption or password requirements.
    What can the problem be?
    CD PROBLEM: 
    With the Range Expander, I got a CD, when I run the CD, I try to install it, and come to "Performing Site Survey" And then after reaching 100% it pops up an error message: Site Survey Failed. Please try again.
    I apologize for my bad English.
    Greets: Stefan Brannfjell
    Message Edited by Znote on 10-10-2009 11:37 AM

    By default IP Address of the WRE54G is 192.168.1.240.Change the IP Address of the WRE54G(Range Expander) in the Range of AP..i.e..10.0.0.240 and default gateway same as of the AP.

  • [SOLVED] Wireless Connection Problems - Broadcom Corporation BCM4318

    Attempting to troubleshoot wifi connectivity issues on a fresh install on an old dell Inspiron 2200. This laptop uses the Broadcom b43 driver:
    http://wireless.kernel.org/en/users/Drivers/b43
    I read that page top to bottom, installed b43-fwcutter firmware extraction tool, installed the b43 driver. lsmod confirms b43 is installed. lspci shows the drivers are installed, but I can't get the interface to show with ip link or ip addr.
    lspci -vnn | grep 14e4:
    02:03.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
    I'm confused by dmesg below because it first tells me that "b43-phy0: Broadcom 4318 WLAN found" then a few lines down says driver not found.
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.12.6-1-ARCH (tobias@testing-i686) (gcc version 4.8.2 (GCC) ) #1 SMP PREEMPT Fri Dec 20 19:54:53 CET 2013
    [ 0.000000] Disabled fast string operations
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001f7d37ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000001f7d3800-0x000000001fffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000f0006fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f0008000-0x00000000f000bfff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec0ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fee0ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] SMBIOS 2.3 present.
    [ 0.000000] DMI: Dell Inc. Inspiron 2200 /0U6962, BIOS A07 12/01/2005
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] e820: last_pfn = 0x1f7d3 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-EFFFF uncachable
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask FE0000000 write-back
    [ 0.000000] 1 base 01F800000 mask FFF800000 uncachable
    [ 0.000000] 2 base 0FEDA0000 mask FFFFE0000 write-through
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] PAT not supported by CPU.
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
    [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x1f000000-0x1f3fffff]
    [ 0.000000] [mem 0x1f000000-0x1f3fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x18000000-0x1effffff]
    [ 0.000000] [mem 0x18000000-0x1effffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x17ffffff]
    [ 0.000000] [mem 0x00100000-0x003fffff] page 4k
    [ 0.000000] [mem 0x00400000-0x17ffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x1f400000-0x1f7d2fff]
    [ 0.000000] [mem 0x1f400000-0x1f7d2fff] page 4k
    [ 0.000000] BRK [0x0177c000, 0x0177cfff] PGTABLE
    [ 0.000000] RAMDISK: [mem 0x1e9af000-0x1ec8efff]
    [ 0.000000] ACPI: RSDP 000fc9b0 00014 (v00 DELL )
    [ 0.000000] ACPI: RSDT 1f7d4425 00038 (v01 DELL CPi R 27D50C01 ASL 00000061)
    [ 0.000000] ACPI: FACP 1f7d4c00 00074 (v01 DELL CPi R 27D50C01 ASL 00000061)
    [ 0.000000] ACPI: DSDT 1f7d5800 02D9A (v01 INT430 SYSFexxx 00001001 MSFT 0100000E)
    [ 0.000000] ACPI: FACS 1f7e4000 00040
    [ 0.000000] ACPI: APIC 1f7d5400 00068 (v01 DELL CPi R 27D50C01 ASL 00000047)
    [ 0.000000] ACPI: MCFG 1f7d53c0 0003E (v16 DELL CPi R 27D50C01 ASL 00000061)
    [ 0.000000] ACPI: SSDT 1f7d4658 001D8 (v01 PmRef Cpu0Cst 00003001 INTL 20030522)
    [ 0.000000] ACPI: SSDT 1f7d445d 001FB (v01 PmRef CpuPm 00003000 INTL 20030522)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 0MB HIGHMEM available.
    [ 0.000000] 503MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 1f7d3000
    [ 0.000000] low ram: 0 - 1f7d3000
    [ 0.000000] BRK [0x0177d000, 0x0177dfff] PGTABLE
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] Normal [mem 0x01000000-0x1f7d2fff]
    [ 0.000000] HighMem empty
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0x1f7d2fff]
    [ 0.000000] On node 0 totalpages: 128881
    [ 0.000000] free_area_init_node: node 0, pgdat c15d6680, node_mem_map df3e3020
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] Normal zone: 976 pages used for memmap
    [ 0.000000] Normal zone: 124883 pages, LIFO batch:31
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] smpboot: Allowing 2 CPUs, 1 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
    [ 0.000000] e820: [mem 0x20000000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 14 pages/cpu @df3c3000 s33408 r0 d23936 u57344
    [ 0.000000] pcpu-alloc: s33408 r0 d23936 u57344 alloc=14*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127873
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=1ea77b37-4f05-412d-ac82-fa0302942b0a rw quiet
    [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 1031824 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
    [ 0.000000] Memory: 499264K/515524K available (4325K kernel code, 435K rwdata, 1280K rodata, 612K init, 952K bss, 16260K reserved, 0K highmem)
    [ 0.000000] virtual kernel memory layout:
    fixmap : 0xfff15000 - 0xfffff000 ( 936 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xdffd3000 - 0xff7fe000 ( 504 MB)
    lowmem : 0xc0000000 - 0xdf7d3000 ( 503 MB)
    .init : 0xc15e8000 - 0xc1681000 ( 612 kB)
    .data : 0xc1439b1e - 0xc15e7c80 (1720 kB)
    .text : 0xc1000000 - 0xc1439b1e (4326 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
    [ 0.000000] NR_IRQS:2304 nr_irqs:512 16
    [ 0.000000] CPU 0 irqstacks, hard=de408000 soft=de40a000
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 1695.712 MHz processor
    [ 0.003337] Calibrating delay loop (skipped), value calculated using timer frequency.. 3392.73 BogoMIPS (lpj=5652373)
    [ 0.003344] pid_max: default: 32768 minimum: 301
    [ 0.003408] Security Framework initialized
    [ 0.003431] AppArmor: AppArmor disabled by boot time parameter
    [ 0.003433] Yama: becoming mindful.
    [ 0.003466] Mount-cache hash table entries: 512
    [ 0.003846] Initializing cgroup subsys memory
    [ 0.003868] Initializing cgroup subsys devices
    [ 0.003873] Initializing cgroup subsys freezer
    [ 0.003877] Initializing cgroup subsys net_cls
    [ 0.003880] Initializing cgroup subsys blkio
    [ 0.003924] Disabled fast string operations
    [ 0.003935] mce: CPU supports 5 MCE banks
    [ 0.003951] CPU0: Thermal monitoring enabled (TM1)
    [ 0.003973] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2
    Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8
    tlb_flushall_shift: 6
    [ 0.012193] ACPI: Core revision 20130725
    [ 0.014714] ACPI: All ACPI Tables successfully acquired
    [ 0.016678] ftrace: allocating 19323 entries in 38 pages
    [ 0.023514] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.023984] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.058943] smpboot: CPU0: Intel(R) Celeron(R) M processor 1.70GHz (fam: 06, model: 0d, stepping: 08)
    [ 0.059999] Performance Events: p6 PMU driver.
    [ 0.059999] ... version: 0
    [ 0.059999] ... bit width: 32
    [ 0.059999] ... generic registers: 2
    [ 0.059999] ... value mask: 00000000ffffffff
    [ 0.059999] ... max period: 000000007fffffff
    [ 0.059999] ... fixed-purpose events: 0
    [ 0.059999] ... event mask: 0000000000000003
    [ 0.076688] Brought up 1 CPUs
    [ 0.076696] smpboot: Total of 1 processors activated (3392.73 BogoMIPS)
    [ 0.077595] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.077784] devtmpfs: initialized
    [ 0.079834] RTC time: 16:30:00, date: 12/02/05
    [ 0.079907] NET: Registered protocol family 16
    [ 0.080131] cpuidle: using governor ladder
    [ 0.080134] cpuidle: using governor menu
    [ 0.080205] ACPI: bus type PCI registered
    [ 0.080210] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.080305] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.080310] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.080312] PCI: Using MMCONFIG for extended config space
    [ 0.080314] PCI: Using configuration type 1 for base access
    [ 0.080329] dmi type 0xB1 record - unknown flag
    [ 0.081371] bio: create slab <bio-0> at 0
    [ 0.081531] ACPI: Added _OSI(Module Device)
    [ 0.081534] ACPI: Added _OSI(Processor Device)
    [ 0.081537] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.081540] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.082264] ACPI: EC: Look up EC in DSDT
    [ 0.086461] ACPI: Interpreter enabled
    [ 0.086477] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130725/hwxface-571)
    [ 0.086484] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
    [ 0.086503] ACPI: (supports S0 S3 S4 S5)
    [ 0.086506] ACPI: Using IOAPIC for interrupt routing
    [ 0.086543] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.086682] ACPI: No dock devices found.
    [ 0.103158] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.103168] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
    [ 0.103172] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
    [ 0.118369] acpi PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.118374] acpi PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.118377] acpi PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.118381] acpi PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
    [ 0.118384] acpi PNP0A03:00: host bridge window [mem 0x20000000-0xdfffffff] (ignored)
    [ 0.118388] acpi PNP0A03:00: host bridge window [mem 0xf0007000-0xf0007fff] (ignored)
    [ 0.118391] acpi PNP0A03:00: host bridge window [mem 0xf000c000-0xfebfffff] (ignored)
    [ 0.118395] acpi PNP0A03:00: host bridge window [mem 0xfec10000-0xfed1ffff] (ignored)
    [ 0.118399] acpi PNP0A03:00: host bridge window [mem 0xfee10000-0xffafffff] (ignored)
    [ 0.118402] PCI: root bus 00: using default resources
    [ 0.118519] ACPI: \_SB_.PCI0.MB2_: can't evaluate _ADR (0x5)
    [ 0.118523] ACPI: \_SB_.PCI0.MB3_: can't evaluate _ADR (0x5)
    [ 0.118571] ACPI: \_SB_.PCI0.LNKA: can't evaluate _ADR (0x5)
    [ 0.118575] ACPI: \_SB_.PCI0.LNKB: can't evaluate _ADR (0x5)
    [ 0.118578] ACPI: \_SB_.PCI0.LNKC: can't evaluate _ADR (0x5)
    [ 0.118581] ACPI: \_SB_.PCI0.LNKD: can't evaluate _ADR (0x5)
    [ 0.118585] ACPI: \_SB_.PCI0.LNKE: can't evaluate _ADR (0x5)
    [ 0.118588] ACPI: \_SB_.PCI0.LNKF: can't evaluate _ADR (0x5)
    [ 0.118592] ACPI: \_SB_.PCI0.LNKH: can't evaluate _ADR (0x5)
    [ 0.118629] ACPI: \_SB_.PCI0.MB7_: can't evaluate _ADR (0x5)
    [ 0.118638] PCI host bridge to bus 0000:00
    [ 0.118643] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.118646] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    [ 0.118650] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
    [ 0.118664] pci 0000:00:00.0: [8086:2590] type 00 class 0x060000
    [ 0.118801] pci 0000:00:02.0: [8086:2592] type 00 class 0x030000
    [ 0.118815] pci 0000:00:02.0: reg 0x10: [mem 0xdff00000-0xdff7ffff]
    [ 0.118823] pci 0000:00:02.0: reg 0x14: [io 0xec38-0xec3f]
    [ 0.118831] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
    [ 0.118839] pci 0000:00:02.0: reg 0x1c: [mem 0xdfec0000-0xdfefffff]
    [ 0.118957] pci 0000:00:02.1: [8086:2792] type 00 class 0x038000
    [ 0.118968] pci 0000:00:02.1: reg 0x10: [mem 0xdff80000-0xdfffffff]
    [ 0.119150] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300
    [ 0.119207] pci 0000:00:1d.0: reg 0x20: [io 0xbf80-0xbf9f]
    [ 0.119307] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.119366] pci 0000:00:1d.1: [8086:2659] type 00 class 0x0c0300
    [ 0.119424] pci 0000:00:1d.1: reg 0x20: [io 0xbf60-0xbf7f]
    [ 0.119520] pci 0000:00:1d.1: System wakeup disabled by ACPI
    [ 0.119582] pci 0000:00:1d.2: [8086:265a] type 00 class 0x0c0300
    [ 0.119640] pci 0000:00:1d.2: reg 0x20: [io 0xbf40-0xbf5f]
    [ 0.119736] pci 0000:00:1d.2: System wakeup disabled by ACPI
    [ 0.119797] pci 0000:00:1d.3: [8086:265b] type 00 class 0x0c0300
    [ 0.119856] pci 0000:00:1d.3: reg 0x20: [io 0xbf20-0xbf3f]
    [ 0.119951] pci 0000:00:1d.3: System wakeup disabled by ACPI
    [ 0.120025] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320
    [ 0.120051] pci 0000:00:1d.7: reg 0x10: [mem 0xffa80800-0xffa80bff]
    [ 0.120160] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.120243] pci 0000:00:1d.7: System wakeup disabled by ACPI
    [ 0.120312] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
    [ 0.120441] pci 0000:00:1e.0: System wakeup disabled by ACPI
    [ 0.120505] pci 0000:00:1e.2: [8086:266e] type 00 class 0x040100
    [ 0.120528] pci 0000:00:1e.2: reg 0x10: [io 0xed00-0xedff]
    [ 0.120541] pci 0000:00:1e.2: reg 0x14: [io 0xec40-0xec7f]
    [ 0.120555] pci 0000:00:1e.2: reg 0x18: [mem 0xdfebfe00-0xdfebffff]
    [ 0.120568] pci 0000:00:1e.2: reg 0x1c: [mem 0xdfebfd00-0xdfebfdff]
    [ 0.120634] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
    [ 0.120741] pci 0000:00:1e.3: [8086:266d] type 00 class 0x070300
    [ 0.120764] pci 0000:00:1e.3: reg 0x10: [io 0xee00-0xeeff]
    [ 0.120777] pci 0000:00:1e.3: reg 0x14: [io 0xec80-0xecff]
    [ 0.120864] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
    [ 0.120923] pci 0000:00:1e.3: System wakeup disabled by ACPI
    [ 0.120987] pci 0000:00:1f.0: [8086:2641] type 00 class 0x060100
    [ 0.121103] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
    [ 0.121117] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
    [ 0.121124] pci 0000:00:1f.0: quirk: [io 0x1080-0x10bf] claimed by ICH6 GPIO
    [ 0.121130] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 0900-097f
    [ 0.121234] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a
    [ 0.121253] pci 0000:00:1f.1: reg 0x10: [io 0x01f0-0x01f7]
    [ 0.121266] pci 0000:00:1f.1: reg 0x14: [io 0x03f4-0x03f7]
    [ 0.121280] pci 0000:00:1f.1: reg 0x18: [io 0x0170-0x0177]
    [ 0.121293] pci 0000:00:1f.1: reg 0x1c: [io 0x0374-0x0377]
    [ 0.121307] pci 0000:00:1f.1: reg 0x20: [io 0xbfa0-0xbfaf]
    [ 0.121430] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500
    [ 0.121506] pci 0000:00:1f.3: reg 0x20: [io 0x10c0-0x10df]
    [ 0.121732] pci 0000:02:01.0: [104c:ac56] type 02 class 0x060700
    [ 0.121757] pci 0000:02:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
    [ 0.121801] pci 0000:02:01.0: supports D1 D2
    [ 0.121805] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.121888] pci 0000:02:03.0: [14e4:4318] type 00 class 0x028000
    [ 0.121907] pci 0000:02:03.0: reg 0x10: [mem 0xdfdfe000-0xdfdfffff]
    [ 0.122049] pci 0000:02:08.0: [8086:1068] type 00 class 0x020000
    [ 0.122073] pci 0000:02:08.0: reg 0x10: [mem 0xdfdfd000-0xdfdfdfff]
    [ 0.122086] pci 0000:02:08.0: reg 0x14: [io 0xdf40-0xdf7f]
    [ 0.122175] pci 0000:02:08.0: supports D1 D2
    [ 0.122178] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.122287] pci 0000:00:1e.0: PCI bridge to [bus 02-03] (subtractive decode)
    [ 0.122293] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
    [ 0.122299] pci 0000:00:1e.0: bridge window [mem 0xdfd00000-0xdfdfffff]
    [ 0.122308] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.122312] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
    [ 0.122388] pci_bus 0000:03: busn_res: can not insert [bus 03-ff] under [bus 02-03] (conflicts with (null) [bus 02-03])
    [ 0.122394] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 06
    [ 0.122399] pci_bus 0000:03: busn_res: can not insert [bus 03-06] under [bus 02-03] (conflicts with (null) [bus 02-03])
    [ 0.122405] pci_bus 0000:03: [bus 03-06] partially hidden behind transparent bridge 0000:02 [bus 02-03]
    [ 0.122419] pci_bus 0000:00: on NUMA node 0
    [ 0.122631] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
    [ 0.122757] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
    [ 0.122881] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
    [ 0.123003] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
    [ 0.123127] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 *4 5 6 7 9 10 11 12 14 15)
    [ 0.123238] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
    [ 0.123356] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
    [ 0.123730] ACPI: Enabled 2 GPEs in block 00 to 1F
    [ 0.123805] ACPI: \_SB_.PCI0: notify handler is installed
    [ 0.123844] Found 1 acpi root devices
    [ 0.123976] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.123982] vgaarb: loaded
    [ 0.123984] vgaarb: bridge control possible 0000:00:02.0
    [ 0.124048] PCI: Using ACPI for IRQ routing
    [ 0.135127] PCI: pci_cache_line_size set to 64 bytes
    [ 0.135189] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
    [ 0.135192] e820: reserve RAM buffer [mem 0x1f7d3800-0x1fffffff]
    [ 0.135363] NetLabel: Initializing
    [ 0.135366] NetLabel: domain hash size = 128
    [ 0.135367] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.135386] NetLabel: unlabeled traffic allowed by default
    [ 0.135576] hpet clockevent registered
    [ 0.135581] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.135588] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.135594] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.136700] Switched to clocksource hpet
    [ 0.145683] pnp: PnP ACPI init
    [ 0.145720] ACPI: bus type PNP registered
    [ 0.155581] system 00:00: [mem 0x00000000-0x0009fbff] could not be reserved
    [ 0.155587] system 00:00: [mem 0x0009fc00-0x0009ffff] could not be reserved
    [ 0.155591] system 00:00: [mem 0x000c0000-0x000cffff] could not be reserved
    [ 0.155595] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.155599] system 00:00: [mem 0x00100000-0x1f7d37ff] could not be reserved
    [ 0.155603] system 00:00: [mem 0x1f7d3800-0x1f7fffff] has been reserved
    [ 0.155607] system 00:00: [mem 0x1f800000-0x1fffffff] has been reserved
    [ 0.155611] system 00:00: [mem 0xfeda0000-0xfedfffff] has been reserved
    [ 0.155615] system 00:00: [mem 0xffb00000-0xffffffff] has been reserved
    [ 0.155619] system 00:00: [mem 0xfec00000-0xfec0ffff] could not be reserved
    [ 0.155623] system 00:00: [mem 0xfee00000-0xfee0ffff] has been reserved
    [ 0.155627] system 00:00: [mem 0xfed20000-0xfed9ffff] has been reserved
    [ 0.155631] system 00:00: [mem 0xf0000000-0xf0003fff] has been reserved
    [ 0.155635] system 00:00: [mem 0xf0004000-0xf0004fff] has been reserved
    [ 0.155649] system 00:00: [mem 0xf0005000-0xf0005fff] has been reserved
    [ 0.155653] system 00:00: [mem 0xf0006000-0xf0006fff] has been reserved
    [ 0.155657] system 00:00: [mem 0xf0008000-0xf000bfff] has been reserved
    [ 0.155660] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.155668] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.155730] pnp 00:01: disabling [io 0x1000-0x1005] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.155734] pnp 00:01: disabling [io 0x1008-0x100f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.155776] system 00:01: [io 0x04d0-0x04d1] has been reserved
    [ 0.155781] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.155818] pnp 00:02: disabling [io 0x1006-0x1007] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.155823] pnp 00:02: disabling [io 0x100a-0x1059] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.155827] pnp 00:02: disabling [io 0x1060-0x107f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x1000-0x107f]
    [ 0.155864] system 00:02: [io 0xf400-0xf4fe] has been reserved
    [ 0.155869] system 00:02: [io 0x1080-0x10bf] has been reserved
    [ 0.155872] system 00:02: [io 0x10c0-0x10df] has been reserved
    [ 0.155876] system 00:02: [io 0x10e0-0x10ff] could not be reserved
    [ 0.155881] system 00:02: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.155961] pnp 00:03: Plug and Play ACPI device, IDs PNP0f13 (active)
    [ 0.156020] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.156074] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.156133] pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.156198] system 00:07: [io 0x0900-0x090f] has been reserved
    [ 0.156202] system 00:07: [io 0x0910-0x091f] has been reserved
    [ 0.156206] system 00:07: [io 0x0920-0x092f] has been reserved
    [ 0.156210] system 00:07: [io 0x0930-0x093f] has been reserved
    [ 0.156214] system 00:07: [io 0x0940-0x097f] has been reserved
    [ 0.156219] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.156245] pnp 00:08: [dma 4]
    [ 0.156291] pnp 00:08: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.156350] pnp 00:09: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.157119] pnp 00:0a: disabling [io 0xd3b0-0xd3bb] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157124] pnp 00:0a: disabling [io 0xd3c0-0xd3df] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157129] pnp 00:0a: disabling [io 0xd7b0-0xd7bb] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157133] pnp 00:0a: disabling [io 0xd7c0-0xd7df] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157138] pnp 00:0a: disabling [io 0xdbb0-0xdbbb] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157143] pnp 00:0a: disabling [io 0xdbc0-0xdbdf] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157147] pnp 00:0a: disabling [io 0xdfb0-0xdfbb] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157152] pnp 00:0a: disabling [io 0xdfc0-0xdfdf] because it overlaps 0000:00:1e.0 BAR 13 [io 0xd000-0xdfff]
    [ 0.157612] system 00:0a: [io 0x07b0-0x07bb] has been reserved
    [ 0.157616] system 00:0a: [io 0x07c0-0x07df] has been reserved
    [ 0.157620] system 00:0a: [io 0x0bb0-0x0bbb] has been reserved
    [ 0.157623] system 00:0a: [io 0x0bc0-0x0bdf] has been reserved
    [ 0.157627] system 00:0a: [io 0x0fb0-0x0fbb] has been reserved
    [ 0.157631] system 00:0a: [io 0x0fc0-0x0fdf] has been reserved
    [ 0.157635] system 00:0a: [io 0x13b0-0x13bb] has been reserved
    [ 0.157638] system 00:0a: [io 0x13c0-0x13df] has been reserved
    [ 0.157642] system 00:0a: [io 0x17b0-0x17bb] has been reserved
    [ 0.157646] system 00:0a: [io 0x17c0-0x17df] has been reserved
    [ 0.157649] system 00:0a: [io 0x1bb0-0x1bbb] has been reserved
    [ 0.157653] system 00:0a: [io 0x1bc0-0x1bdf] has been reserved
    [ 0.157657] system 00:0a: [io 0x1fb0-0x1fbb] has been reserved
    [ 0.157661] system 00:0a: [io 0x1fc0-0x1fdf] has been reserved
    [ 0.157664] system 00:0a: [io 0x23b0-0x23bb] has been reserved
    [ 0.157668] system 00:0a: [io 0x23c0-0x23df] has been reserved
    [ 0.157672] system 00:0a: [io 0x27b0-0x27bb] has been reserved
    [ 0.157676] system 00:0a: [io 0x27c0-0x27df] has been reserved
    [ 0.157679] system 00:0a: [io 0x2bb0-0x2bbb] has been reserved
    [ 0.157683] system 00:0a: [io 0x2bc0-0x2bdf] has been reserved
    [ 0.157687] system 00:0a: [io 0x2fb0-0x2fbb] has been reserved
    [ 0.157691] system 00:0a: [io 0x2fc0-0x2fdf] has been reserved
    [ 0.157695] system 00:0a: [io 0x33b0-0x33bb] has been reserved
    [ 0.157698] system 00:0a: [io 0x33c0-0x33df] has been reserved
    [ 0.157702] system 00:0a: [io 0x37b0-0x37bb] has been reserved
    [ 0.157706] system 00:0a: [io 0x37c0-0x37df] has been reserved
    [ 0.157710] system 00:0a: [io 0x3bb0-0x3bbb] has been reserved
    [ 0.157714] system 00:0a: [io 0x3bc0-0x3bdf] has been reserved
    [ 0.157717] system 00:0a: [io 0x3fb0-0x3fbb] has been reserved
    [ 0.157721] system 00:0a: [io 0x3fc0-0x3fdf] has been reserved
    [ 0.157725] system 00:0a: [io 0x43b0-0x43bb] has been reserved
    [ 0.157729] system 00:0a: [io 0x43c0-0x43df] has been reserved
    [ 0.157733] system 00:0a: [io 0x47b0-0x47bb] has been reserved
    [ 0.157737] system 00:0a: [io 0x47c0-0x47df] has been reserved
    [ 0.157741] system 00:0a: [io 0x4bb0-0x4bbb] has been reserved
    [ 0.157745] system 00:0a: [io 0x4bc0-0x4bdf] has been reserved
    [ 0.157748] system 00:0a: [io 0x4fb0-0x4fbb] has been reserved
    [ 0.157752] system 00:0a: [io 0x4fc0-0x4fdf] has been reserved
    [ 0.157756] system 00:0a: [io 0x53b0-0x53bb] has been reserved
    [ 0.157760] system 00:0a: [io 0x53c0-0x53df] has been reserved
    [ 0.157764] system 00:0a: [io 0x57b0-0x57bb] has been reserved
    [ 0.157768] system 00:0a: [io 0x57c0-0x57df] has been reserved
    [ 0.157772] system 00:0a: [io 0x5bb0-0x5bbb] has been reserved
    [ 0.157776] system 00:0a: [io 0x5bc0-0x5bdf] has been reserved
    [ 0.157780] system 00:0a: [io 0x5fb0-0x5fbb] has been reserved
    [ 0.157784] system 00:0a: [io 0x5fc0-0x5fdf] has been reserved
    [ 0.157788] system 00:0a: [io 0x63b0-0x63bb] has been reserved
    [ 0.157792] system 00:0a: [io 0x63c0-0x63df] has been reserved
    [ 0.157795] system 00:0a: [io 0x67b0-0x67bb] has been reserved
    [ 0.157804] system 00:0a: [io 0x67c0-0x67df] has been reserved
    [ 0.157808] system 00:0a: [io 0x6bb0-0x6bbb] has been reserved
    [ 0.157812] system 00:0a: [io 0x6bc0-0x6bdf] has been reserved
    [ 0.157816] system 00:0a: [io 0x6fb0-0x6fbb] has been reserved
    [ 0.157820] system 00:0a: [io 0x6fc0-0x6fdf] has been reserved
    [ 0.157824] system 00:0a: [io 0x73b0-0x73bb] has been reserved
    [ 0.157828] system 00:0a: [io 0x73c0-0x73df] has been reserved
    [ 0.157832] system 00:0a: [io 0x77b0-0x77bb] has been reserved
    [ 0.157836] system 00:0a: [io 0x77c0-0x77df] has been reserved
    [ 0.157840] system 00:0a: [io 0x7bb0-0x7bbb] has been reserved
    [ 0.157844] system 00:0a: [io 0x7bc0-0x7bdf] has been reserved
    [ 0.157848] system 00:0a: [io 0x7fb0-0x7fbb] has been reserved
    [ 0.157852] system 00:0a: [io 0x7fc0-0x7fdf] has been reserved
    [ 0.157856] system 00:0a: [io 0x83b0-0x83bb] has been reserved
    [ 0.157860] system 00:0a: [io 0x83c0-0x83df] has been reserved
    [ 0.157864] system 00:0a: [io 0x87b0-0x87bb] has been reserved
    [ 0.157868] system 00:0a: [io 0x87c0-0x87df] has been reserved
    [ 0.157872] system 00:0a: [io 0x8bb0-0x8bbb] has been reserved
    [ 0.157876] system 00:0a: [io 0x8bc0-0x8bdf] has been reserved
    [ 0.157880] system 00:0a: [io 0x8fb0-0x8fbb] has been reserved
    [ 0.157884] system 00:0a: [io 0x8fc0-0x8fdf] has been reserved
    [ 0.157888] system 00:0a: [io 0x93b0-0x93bb] has been reserved
    [ 0.157892] system 00:0a: [io 0x93c0-0x93df] has been reserved
    [ 0.157896] system 00:0a: [io 0x97b0-0x97bb] has been reserved
    [ 0.157901] system 00:0a: [io 0x97c0-0x97df] has been reserved
    [ 0.157905] system 00:0a: [io 0x9bb0-0x9bbb] has been reserved
    [ 0.157909] system 00:0a: [io 0x9bc0-0x9bdf] has been reserved
    [ 0.157913] system 00:0a: [io 0x9fb0-0x9fbb] has been reserved
    [ 0.157917] system 00:0a: [io 0x9fc0-0x9fdf] has been reserved
    [ 0.157921] system 00:0a: [io 0xa3b0-0xa3bb] has been reserved
    [ 0.157925] system 00:0a: [io 0xa3c0-0xa3df] has been reserved
    [ 0.157930] system 00:0a: [io 0xa7b0-0xa7bb] has been reserved
    [ 0.157934] system 00:0a: [io 0xa7c0-0xa7df] has been reserved
    [ 0.157938] system 00:0a: [io 0xabb0-0xabbb] has been reserved
    [ 0.157942] system 00:0a: [io 0xabc0-0xabdf] has been reserved
    [ 0.157946] system 00:0a: [io 0xafb0-0xafbb] has been reserved
    [ 0.157950] system 00:0a: [io 0xafc0-0xafdf] has been reserved
    [ 0.157955] system 00:0a: [io 0xb3b0-0xb3bb] has been reserved
    [ 0.157959] system 00:0a: [io 0xb3c0-0xb3df] has been reserved
    [ 0.157963] system 00:0a: [io 0xb7b0-0xb7bb] has been reserved
    [ 0.157967] system 00:0a: [io 0xb7c0-0xb7df] has been reserved
    [ 0.157971] system 00:0a: [io 0xbbb0-0xbbbb] has been reserved
    [ 0.157976] system 00:0a: [io 0xbbc0-0xbbdf] has been reserved
    [ 0.157980] system 00:0a: [io 0xbfb0-0xbfbb] has been reserved
    [ 0.157984] system 00:0a: [io 0xbfc0-0xbfdf] has been reserved
    [ 0.157988] system 00:0a: [io 0xc3b0-0xc3bb] has been reserved
    [ 0.157993] system 00:0a: [io 0xc3c0-0xc3df] has been reserved
    [ 0.157997] system 00:0a: [io 0xc7b0-0xc7bb] has been reserved
    [ 0.158001] system 00:0a: [io 0xc7c0-0xc7df] has been reserved
    [ 0.158005] system 00:0a: [io 0xcbb0-0xcbbb] has been reserved
    [ 0.158010] system 00:0a: [io 0xcbc0-0xcbdf] has been reserved
    [ 0.158014] system 00:0a: [io 0xcfb0-0xcfbb] has been reserved
    [ 0.158018] system 00:0a: [io 0xcfc0-0xcfdf] has been reserved
    [ 0.158026] system 00:0a: [io 0xe3b0-0xe3bb] has been reserved
    [ 0.158030] system 00:0a: [io 0xe3c0-0xe3df] has been reserved
    [ 0.158034] system 00:0a: [io 0xe7b0-0xe7bb] has been reserved
    [ 0.158039] system 00:0a: [io 0xe7c0-0xe7df] has been reserved
    [ 0.158043] system 00:0a: [io 0xebb0-0xebbb] has been reserved
    [ 0.158048] system 00:0a: [io 0xebc0-0xebdf] has been reserved
    [ 0.158052] system 00:0a: [io 0xefb0-0xefbb] has been reserved
    [ 0.158056] system 00:0a: [io 0xefc0-0xefdf] has been reserved
    [ 0.158061] system 00:0a: [io 0xf3b0-0xf3bb] has been reserved
    [ 0.158065] system 00:0a: [io 0xf3c0-0xf3df] has been reserved
    [ 0.158070] system 00:0a: [io 0xf7b0-0xf7bb] has been reserved
    [ 0.158074] system 00:0a: [io 0xf7c0-0xf7df] has been reserved
    [ 0.158079] system 00:0a: [io 0xfbb0-0xfbbb] has been reserved
    [ 0.158083] system 00:0a: [io 0xfbc0-0xfbdf] has been reserved
    [ 0.158088] system 00:0a: [io 0xffb0-0xffbb] has been reserved
    [ 0.158092] system 00:0a: [io 0xffc0-0xffdf] has been reserved
    [ 0.158098] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.158112] pnp: PnP ACPI: found 11 devices
    [ 0.158114] ACPI: bus type PNP unregistered
    [ 0.195319] pci 0000:02:01.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
    [ 0.195329] pci 0000:00:1e.0: bridge window [mem 0x04000000-0x03ffffff pref] to [bus 02-03] add_size 4000000
    [ 0.195340] pci 0000:00:1e.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
    [ 0.195348] pci 0000:00:1e.0: BAR 15: assigned [mem 0x20000000-0x23ffffff pref]
    [ 0.195356] pci 0000:02:01.0: res[15]=[mem 0x04000000-0x03ffffff pref] get_res_add_size add_size 4000000
    [ 0.195360] pci 0000:02:01.0: res[16]=[mem 0x04000000-0x03ffffff] get_res_add_size add_size 4000000
    [ 0.195364] pci 0000:02:01.0: res[13]=[io 0x0100-0x00ff] get_res_add_size add_size 100
    [ 0.195368] pci 0000:02:01.0: res[14]=[io 0x0100-0x00ff] get_res_add_size add_size 100
    [ 0.195372] pci 0000:02:01.0: BAR 0: assigned [mem 0x24000000-0x24000fff]
    [ 0.195382] pci 0000:02:01.0: BAR 15: assigned [mem 0x20000000-0x23ffffff pref]
    [ 0.195386] pci 0000:02:01.0: BAR 16: assigned [mem 0x28000000-0x2bffffff]
    [ 0.195390] pci 0000:02:01.0: BAR 13: assigned [io 0xd000-0xd0ff]
    [ 0.195393] pci 0000:02:01.0: BAR 14: assigned [io 0xd400-0xd4ff]
    [ 0.195398] pci 0000:02:01.0: CardBus bridge to [bus 03-06]
    [ 0.195401] pci 0000:02:01.0: bridge window [io 0xd000-0xd0ff]
    [ 0.195408] pci 0000:02:01.0: bridge window [io 0xd400-0xd4ff]
    [ 0.195415] pci 0000:02:01.0: bridge window [mem 0x20000000-0x23ffffff pref]
    [ 0.195422] pci 0000:02:01.0: bridge window [mem 0x28000000-0x2bffffff]
    [ 0.195429] pci 0000:00:1e.0: PCI bridge to [bus 02-03]
    [ 0.195434] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
    [ 0.195442] pci 0000:00:1e.0: bridge window [mem 0xdfd00000-0xdfdfffff]
    [ 0.195448] pci 0000:00:1e.0: bridge window [mem 0x20000000-0x23ffffff pref]
    [ 0.195458] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
    [ 0.195462] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.195466] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
    [ 0.195469] pci_bus 0000:02: resource 1 [mem 0xdfd00000-0xdfdfffff]
    [ 0.195473] pci_bus 0000:02: resource 2 [mem 0x20000000-0x23ffffff pref]
    [ 0.195476] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
    [ 0.195480] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.195483] pci_bus 0000:03: resource 0 [io 0xd000-0xd0ff]
    [ 0.195487] pci_bus 0000:03: resource 1 [io 0xd400-0xd4ff]
    [ 0.195490] pci_bus 0000:03: resource 2 [mem 0x20000000-0x23ffffff pref]
    [ 0.195494] pci_bus 0000:03: resource 3 [mem 0x28000000-0x2bffffff]
    [ 0.195566] NET: Registered protocol family 2
    [ 0.195842] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.195881] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.195912] TCP: Hash tables configured (established 4096 bind 4096)
    [ 0.195944] TCP: reno registered
    [ 0.195948] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.195958] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.196057] NET: Registered protocol family 1
    [ 0.196082] pci 0000:00:02.0: Boot video device
    [ 0.198013] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
    [ 0.198020] PCI: CLS 64 bytes, default 64
    [ 0.198109] Unpacking initramfs...
    [ 0.298578] Freeing initrd memory: 2944K (de9af000 - dec8f000)
    [ 0.298752] apm: BIOS not found.
    [ 0.298829] Scanning for low memory corruption every 60 seconds
    [ 0.299444] audit: initializing netlink socket (disabled)
    [ 0.299469] type=2000 audit(1133541000.296:1): initialized
    [ 0.316577] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.318771] zbud: loaded
    [ 0.318915] VFS: Disk quotas dquot_6.5.2
    [ 0.319000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.319305] msgmni has been set to 980
    [ 0.319650] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.319691] io scheduler noop registered
    [ 0.319693] io scheduler deadline registered
    [ 0.319747] io scheduler cfq registered (default)
    [ 0.319887] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.319914] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.320032] vesafb: mode is 1024x768x32, linelength=4096, pages=0
    [ 0.320034] vesafb: scrolling: redraw
    [ 0.320038] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.320208] vesafb: framebuffer at 0xc0000000, mapped to 0xe0000000, using 3072k, total 3072k
    [ 0.361088] Console: switching to colour frame buffer device 128x48
    [ 0.400929] fb0: VESA VGA frame buffer device
    [ 0.400953] intel_idle: does not run on family 6 model 13
    [ 0.400999] GHES: HEST is not enabled!
    [ 0.401017] isapnp: Scanning for PnP cards...
    [ 0.714052] isapnp: No Plug & Play device found
    [ 0.714124] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.715322] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 0.719975] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.720044] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.720176] mousedev: PS/2 mouse device common for all mice
    [ 0.720505] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
    [ 0.720542] rtc_cmos 00:05: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 0.720656] drop_monitor: Initializing network drop monitor service
    [ 0.720788] TCP: cubic registered
    [ 0.721001] NET: Registered protocol family 10
    [ 0.721277] NET: Registered protocol family 17
    [ 0.721295] Key type dns_resolver registered
    [ 0.721476] Using IPI No-Shortcut mode
    [ 0.721597] registered taskstats version 1
    [ 0.721889] Magic number: 1:361:539
    [ 0.721990] rtc_cmos 00:05: setting system clock to 2005-12-02 16:30:01 UTC (1133541001)
    [ 0.722052] PM: Hibernation image not present or could not be loaded.
    [ 0.722537] Freeing unused kernel memory: 612K (c15e8000 - c1681000)
    [ 0.722565] Write protecting the kernel text: 4328k
    [ 0.722601] Write protecting the kernel read-only data: 1284k
    [ 0.724539] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.740162] systemd-udevd[41]: starting version 208
    [ 0.794552] ACPI: bus type USB registered
    [ 0.794600] usbcore: registered new interface driver usbfs
    [ 0.794617] usbcore: registered new interface driver hub
    [ 0.797519] usbcore: registered new device driver usb
    [ 0.798409] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.798878] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.799189] uhci_hcd 0000:00:1d.0: setting latency timer to 64
    [ 0.799196] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 0.799208] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    [ 0.799269] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
    [ 0.800221] hub 1-0:1.0: USB hub found
    [ 0.800900] hub 1-0:1.0: 2 ports detected
    [ 0.801737] ehci-pci: EHCI PCI platform driver
    [ 0.802153] ehci-pci 0000:00:1d.7: setting latency timer to 64
    [ 0.802310] ehci-pci 0000:00:1d.7: EHCI Host Controller
    [ 0.802319] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
    [ 0.802337] ehci-pci 0000:00:1d.7: debug port 1
    [ 0.806249] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
    [ 0.806261] ehci-pci 0000:00:1d.7: irq 16, io mem 0xffa80800
    [ 0.811120] SCSI subsystem initialized
    [ 0.815534] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 0.816328] hub 2-0:1.0: USB hub found
    [ 0.816344] hub 2-0:1.0: 8 ports detected
    [ 0.822812] libata version 3.00 loaded.
    [ 0.840154] hub 1-0:1.0: USB hub found
    [ 0.840171] hub 1-0:1.0: 2 ports detected
    [ 0.840775] uhci_hcd 0000:00:1d.1: setting latency timer to 64
    [ 0.840781] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 0.840792] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 0.840849] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
    [ 0.841131] hub 3-0:1.0: USB hub found
    [ 0.841142] hub 3-0:1.0: 2 ports detected
    [ 0.841510] uhci_hcd 0000:00:1d.2: setting latency timer to 64
    [ 0.841515] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 0.841523] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 0.841569] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
    [ 0.841792] hub 4-0:1.0: USB hub found
    [ 0.841802] hub 4-0:1.0: 2 ports detected
    [ 0.841974] ata_piix 0000:00:1f.1: version 2.13
    [ 0.842212] ata_piix 0000:00:1f.1: setting latency timer to 64
    [ 0.846327] scsi0 : ata_piix
    [ 0.849479] scsi1 : ata_piix
    [ 0.849561] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
    [ 0.849565] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
    [ 0.850360] uhci_hcd 0000:00:1d.3: setting latency timer to 64
    [ 0.850367] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 0.850377] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 0.850431] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
    [ 0.850702] hub 5-0:1.0: USB hub found
    [ 0.850714] hub 5-0:1.0: 2 ports detected
    [ 0.853261] ata2: port disabled--ignoring
    [ 1.017261] ata1.00: ATA-6: FUJITSU MHV2040AH, 00000096, max UDMA/100
    [ 1.017267] ata1.00: 78140160 sectors, multi 8: LBA
    [ 1.017275] ata1.01: ATAPI: HL-DT-STCD-RW/DVD-ROM GCC-4244N, B101, max UDMA/33
    [ 1.030469] ata1.00: configured for UDMA/100
    [ 1.043650] ata1.01: configured for UDMA/33
    [ 1.047752] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2040A 0000 PQ: 0 ANSI: 5
    [ 1.052402] scsi 0:0:1:0: CD-ROM HL-DT-ST CDRW/DVD GCC4244 B101 PQ: 0 ANSI: 5
    [ 1.056877] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
    [ 1.056959] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.056963] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.056996] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.086053] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    [ 1.086060] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 1.086608] sr 0:0:1:0: Attached scsi CD-ROM sr0
    [ 1.147009] sda: sda1 sda2 sda3 sda4 sda5
    [ 1.148544] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.300030] tsc: Refined TSC clocksource calibration: 1695.749 MHz
    [ 1.914175] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 2.300077] Switched to clocksource tsc
    [ 2.590447] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
    [ 2.601980] systemd[1]: Set hostname to <amycus>.
    [ 3.575622] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 3.576065] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 3.576169] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 3.576193] systemd[1]: Starting Remote File Systems.
    [ 3.576214] systemd[1]: Reached target Remote File Systems.
    [ 3.576230] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 3.576273] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 3.576289] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 3.576327] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 3.576342] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 3.576396] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 3.576411] systemd[1]: Starting Delayed Shutdown Socket.
    [ 3.576445] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 3.576470] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 3.576520] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 3.576535] systemd[1]: Starting Paths.
    [ 3.576551] systemd[1]: Reached target Paths.
    [ 3.576568] systemd[1]: Starting Journal Socket.
    [ 3.576636] systemd[1]: Listening on Journal Socket.
    [ 3.585193] systemd[1]: Starting Apply Kernel Variables...
    [ 3.605471] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 3.605993] systemd[1]: Starting Setup Virtual Console...
    [ 3.606504] systemd[1]: Starting Journal Service...
    [ 3.607153] systemd[1]: Started Journal Service.
    [ 4.079977] systemd-journald[91]: Vacuuming done, freed 0 bytes
    [ 4.428227] EXT4-fs (sda4): re-mounted. Opts: data=ordered
    [ 4.761540] systemd-udevd[121]: starting version 208
    [ 5.340036] tsc: Marking TSC unstable due to TSC halts in idle
    [ 5.340108] ACPI: acpi_idle registered with cpuidle
    [ 5.343558] Switched to clocksource hpet
    [ 5.401187] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
    [ 5.401731] ACPI: Lid Switch [LID]
    [ 5.547764] Linux agpgart interface v0.103
    [ 5.552684] agpgart-intel 0000:00:00.0: Intel 915GM Chipset
    [ 5.552747] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
    [ 5.553017] agpgart-intel 0000:00:00.0: detected 8192K stolen memory
    [ 5.553242] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
    [ 5.631371] [drm] Initialized drm 1.1.0 20060810
    [ 5.688002] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
    [ 5.688080] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input3
    [ 5.688134] [Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
    [ 5.690239] ACPI: Battery Slot [BAT0] (battery present)
    [ 5.690376] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
    [ 5.690384] ACPI: Power Button [PBTN]
    [ 5.690609] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input5
    [ 5.690615] ACPI: Sleep Button [SBTN]
    [ 5.696499] ACPI: AC Adapter [AC] (on-line)
    [ 5.702640] thermal LNXTHERM:00: registered as thermal_zone0
    [ 5.702646] ACPI: Thermal Zone [THM] (26 C)
    [ 5.865078] pci 0000:00:1e.0: setting latency timer to 64
    [ 5.865091] yenta_cardbus 0000:02:01.0: enabling device (0000 -> 0003)
    [ 5.865239] yenta_cardbus 0000:02:01.0: CardBus bridge found [1028:01a4]
    [ 5.865265] yenta_cardbus 0000:02:01.0: Using CSCINT to route CSC interrupts to PCI
    [ 5.865268] yenta_cardbus 0000:02:01.0: Routing CardBus interrupts to PCI
    [ 5.865275] yenta_cardbus 0000:02:01.0: TI: mfunc 0x00001002, devctl 0x64
    [ 5.873287] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
    [ 5.873294] e100: Copyright(c) 1999-2006 Intel Corporation
    [ 5.974184] intel_rng: FWH not detected
    [ 6.027516] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
    [ 6.094160] yenta_cardbus 0000:02:01.0: ISA IRQ mask 0x0cf8, PCI irq 16
    [ 6.094169] yenta_cardbus 0000:02:01.0: Socket status: 30000007
    [ 6.094175] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
    [ 6.094188] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [io 0xd000-0xdfff]
    [ 6.094193] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xd000-0xdfff:
    [ 6.095484] excluding 0xd000-0xd0ff 0xd400-0xd4ff 0xdf40-0xdf7f
    [ 6.108339] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [mem 0xdfd00000-0xdfdfffff]
    [ 6.108347] pcmcia_socket pcmcia_socket0: cs: memory probe 0xdfd00000-0xdfdfffff:
    [ 6.108357] excluding 0xdfdf0000-0xdfdfffff
    [ 6.108363] yenta_cardbus 0000:02:01.0: pcmcia: parent PCI bridge window: [mem 0x20000000-0x23ffffff pref]
    [ 6.108367] pcmcia_socket pcmcia_socket0: cs: memory probe 0x20000000-0x23ffffff:
    [ 6.108378] excluding 0x20000000-0x23ffffff
    [ 6.156766] [drm] Memory usable by graphics device = 256M
    [ 6.156776] checking generic (c0000000 300000) vs hw (c0000000 10000000)
    [ 6.156779] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver
    [ 6.156809] Console: switching to colour dummy device 80x25
    [ 6.156943] i915 0000:00:02.0: setting latency timer to 64
    [ 6.157242] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 6.157245] [drm] Driver supports precise vblank timestamp query.
    [ 6.157329] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 6.196410] e100 0000:02:08.0 eth0: addr 0xdfdfd000, irq 20, MAC addr 00:14:22:c2:f4:70
    [ 6.221350] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 6.228810] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
    [ 6.236782] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
    [ 6.236794] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
    [ 6.236802] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
    [ 6.236810] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
    [ 6.236817] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
    [ 6.245149] [drm] initialized overlay support
    [ 6.275242] ssb: Sonics Silicon Backplane found on PCI device 0000:02:03.0
    [ 6.403748] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
    [ 6.812372] gpio_ich: ACPI BAR is busy, GPI 0 - 15 unavailable
    [ 6.812428] gpio_ich: GPIO from 190 to 239 on gpio_ich
    [ 6.816755] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 6.916862] systemd-udevd[123]: renamed network interface eth0 to enp2s8
    [ 6.996643] psmouse serio1: synaptics: Touchpad model: 1, fw: 6.2, id: 0x8fa0b1, caps: 0xa04713/0x200000/0x0, board id: 3655, fw id: 35884
    [ 7.006089] fbcon: inteldrmfb (fb0) is primary device
    [ 7.033421] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
    [ 7.034777] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
    [ 7.036467] excluding 0x170-0x177 0x1f0-0x1f7 0x370-0x377
    [ 7.036511] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
    [ 7.037330] excluding 0x3f0-0x3f7 0x4d0-0x4d7
    [ 7.037357] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
    [ 7.037954] clean.
    [ 7.037978] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
    [ 7.038607] clean.
    [ 7.038632] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
    [ 7.038648] excluding 0xc0000-0xc7fff 0xcc000-0xcffff 0xf0000-0xfffff
    [ 7.038669] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
    [ 7.038683] clean.
    [ 7.038703] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
    [ 7.038716] clean.
    [ 7.038737] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
    [ 7.039386] clean.
    [ 7.063195] iTCO_vendor_support: vendor-support=0
    [ 7.064333] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
    [ 7.064377] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
    [ 7.065219] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 7.182541] cfg80211: Calling CRDA to update world regulatory domain
    [ 7.427229] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
    [ 7.464875] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
    [ 7.484115] Broadcom 43xx driver loaded [ Features: PMNLS ]
    [ 7.486739] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
    [ 7.486740] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
    [ 7.486742] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
    [ 7.553415] Console: switching to colour frame buffer device 128x48
    [ 7.558741] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 7.558745] i915 0000:00:02.0: registered panic notifier
    [ 7.558763] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 7.559077] snd_intel8x0m 0000:00:1e.3: setting latency timer to 64
    [ 7.666733] MC'97 1 converters and GPIO not ready (0xff00)
    [ 7.667845] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
    [ 8.215265] Adding 2097148k swap on /dev/sda3. Priority:-1 extents:1 across:2097148k FS
    [ 8.490136] intel8x0_measure_ac97_clock: measured 51939 usecs (2503 samples)
    [ 8.490144] intel8x0: clocking to 48000
    [ 8.857914] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 8.929489] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 9.174030] systemd-journald[91]: Received request to flush runtime journal from PID 1
    [ 10.867701] IPv6: ADDRCONF(NETDEV_UP): enp2s8: link is not ready
    [ 10.870173] e100 0000:02:08.0 enp2s8: NIC Link is Up 100 Mbps Full Duplex
    [ 10.870468] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s8: link becomes ready
    [ 1442.063296] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
    [ 1442.063313] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
    [ 1442.063321] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
    [ 1442.063329] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
    [ 1442.063337] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
    [ 1442.102223] ssb: Sonics Silicon Backplane found on PCI device 0000:02:03.0
    [ 1442.129092] cfg80211: Calling CRDA to update world regulatory domain
    [ 1442.175516] b43: unknown parameter 'ssb' ignored
    [ 1442.175999] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
    [ 1442.209933] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
    [ 1442.230067] Broadcom 43xx driver loaded [ Features: PMNLS ]
    [ 1442.237090] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
    [ 1442.237099] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
    [ 1442.237103] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
    Last edited by w201 (2013-12-31 22:13:01)

    Got it running, was missing "b43-firmware" from the AUR, which is different than b43-fwcutter. Instructions kind of unclear there, but hey it's running.

  • [Solved?] more Broadcom wireless b43 problems?

    Hello
    I have been trying to get an old Acer Aspire One working for a trip out of the country (where I don't want to carry the 6kg of a Clevo p150em on my back).
    However, the wifi driver isn't working.
    I've got the 14e4:4315 which is supposed to be supported according to this.
    I quickly discovered the arch wiki page for Broadcom wifi drivers and I made sense of it after a little while, realizing that I probably should not blacklist anything or change much at all, contrary to a majority of the text there. The required drivers should be in the kernel, except for the firmware.
    Looking at threads like https://bbs.archlinux.org/viewtopic.php?id=117035 makes me think the only thing I should have to do is download the tarball from AUR, makepkg it, pacman -U it, reboot my system and be happy. Still I end up with a dmesg tail containing the
    b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
    b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
    b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Dri … cefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
    Of course, all the files are in /usr/lib/firmware/b43 (there is no b43-open there though) and /lib is symlinked to there.
    I'm unsure where to go with this now. Any clues?
    Last edited by innsmouthrain (2013-04-18 13:24:16)

    Hi,
    I just went through a very similar problem and thought I should post here.
    I went through a fresh install of Arch using a USB wireless dongle using carl firmware. For some reason (can't remember why) I manually copied carl firmware from my previous install to make it work.
    Anyway, after installing I wanted to start using my built in Broadcom card (4311 by the way) so installed b43-firmware from AUR. Installation finished without errors.
    I 'ip link' and see nothing new. I then
    rmmod b43
    modprobe b43
    and get a freeze. Force shut down, reboot and
    dmesg | grep b43
    and see
    b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
    b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
    b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Dri … cefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
    so I check whether the files exist and they do. I check permissions and see the same as innsmouthrain. I check
    pacman -Ql b43-firmware
    and it returns nothing. Try to reinstall b43-firmware package and see the same '.. exists on filesystem' errors. I then completely removed the b43 folder in /usr/lib/firmware/, removed and installed b43-firmware again. Again checked with
    pacman -Ql b43-firmware
    and hooray the files show up.
    Reboot then
    [stefan@stefan-laptop ~]$ dmesg | grep b43
    [ 8.011883] b43-phy0: Broadcom 4311 WLAN found (core revision 10)
    [ 8.046772] b43-phy0: Found PHY: Analog 4, Type 2 (G), Revision 8
    [ 38.693449] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
    [ 63.843422] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
    [ 75.213447] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
    [ 76.582325] b43 ssb0:0 wlan0: disabling HT/VHT due to WEP/TKIP use
    followed by
    ip link set wlan0 up
    wifi-menu
    It tells me also
    :: Scanning for networks
    > No networks found [FAILED]
    I try again immediately afterwards and it succeeds.
    So that is my story. I didn't need to blacklist bcma by the way. I tried once using both 'blacklist' and 'install' but failed due to b43 being unable to load. According to the wiki
    Since kernel 3.3, the brcmsmac module actually uses bcma, so bcma needs to be unblacklisted or the Wi-Fi interface will not appear.
    so I stopped pursuing that route after reading that.
    I don't know why the files did initially not belong to b43-firmware and why they were not being found. There's a slight chance that I copied by old b43 files manually during installation as well ( I can't remember but it's a very slim chance), tough I think I would have seen errors during first install of b43-firmware then.

  • Problem w/ wireless range with Time Capsule

    Recently set up Time Capsule to swap out my Airport next to my Imac. Also have an Airport Express set up in another room to help extend wireless range. Found now that the range with Time Capsule is not as good as the Airport setup and I can't use my Ipad in the bedrooms furthest away from the Time Capsule. I'm not very tech saavy but would appreciate any suggestions? Thx.

    When you set up TimeCapsule did you create a closed network? With a closed network, airport doesn't broadcast the network name, you have to manually enter it to join. This might be your problem. To fix it (or to see if that's what you've done) run Airport Utility and select manual setup. Select the Wireless tab and then click on the Wireless Options button at the bottom of the window.

  • POOR wireless range

    I have a white 13" macbook which i bought about 6 months ago. We have the new BT home hub wireless router (the black V.2 model). I can get the network no problem in the adjacent rooms but as soon as i go upstairs i get nothing. Can anyone explain why my range is so poor??

    Hi sutton185,
    Welcome to the forum.
    There are a lot of variables that can affect the "performance" of the range of your wireless router. Location of the router, interference from other electronic equipment (telephone, TV, radio etc) and walls are just some that immediately spring to mind.
    In these situations, one of the first things I would do is change the wireless channel and/or the location of the router. If the symptoms still remain, you may need an additional wireless router (like Apple's Airport Express) which will be configured in WDS mode and act in extending the wireless range.
    To change the wireless channel you'll need to log in to your router. With the BTHomehub simply fire up a web browser and enter 192.168.1.1 in the URL field. Click on Advanced... in the left list and Advanced... again. The default username is admin and the password is admin again. Then select Wireless from the Advanced submenu on the left and on the right, at the top, you'll see the following menu items: Settings, Encryption, MAC Address Control, Repeater. Ensure that Setting is selected and from the drop down menu in the Channel field select a different channel and click Apply. You may have to experiment with different channels; try Channel 11 first and work from there.
    Kryten

  • Bluetooth range problem/mac mini

    hello , i have a mac mini with the bluetooth/ airport installed. i have the mini connected to my 36 inch tv. i recently purchased an apple wireless keyboard and mouse. now as i can recall the range of bluetooth should be somewhere in the 30ft range. i was hoping to be able to sit on my couch and use this setup. now when i go more then 1 foot away from the mini with the mouse and keyboard they nolonger work. i updated everything and it still dosnt work. the mouse gets unconnected and the keyboard dosnt work then at all. can someone please help me for now i feel i have wasted my money and am going to return the mini, keyboard and mouse

    I fixed this last night (Mac Mini, Late 2009). If you have upgraded your RAM there is a strong possibility that the bluetooth antenna came loose while reassemling the mini. I was very careful installing ram, but last evening when I dissassembled the mini I found that one of the bluetooth antennae was disconnected. Popped it back in, reassembled, and my reception went from 1 foot back up to the full extent of the room. If you are having range problems, take it apart (ifixit.com) and check it.

  • Help with puzzling wifi range problem on Macbook Pro

    Hi There,
    I am experiencing wifi range problems with my MacBook Pro (10.9.4).
    Our wireless modem (Arris DG860) is located in the office, in the center of our home. The wifi bars register full on my Macbook and the internet works well in office.
    When I move my Macbook to the lounge room, 6 steps away, my internet stops working despite wifi bars remaining full. We also have an Apple TV in the lounge room (I have airplay disconnected on Macbook). 15% of the time, I can somehow get the internet to work in the lounge room (sometimes just by disconnecting airplay),then it mysteriously stops- with wifi bars remaining full.
    85% of time, the internet doesn't work at all in lounge room (still full wifi bars). Other rooms of the house that are similar distances away from modem experience the same problem. We did not experience this problem with our old Macbook pro (purchased in '09). With our old Mac we had same internet connection, modem and Apple TV.
    The only place our current Macbook receives good internet connection is in the office.
    We also have an iPad and two iPhone 4S'
    Any suggestions anyone? TIA

    Most people who live in neighborhoods or apartments are not blessed with so few WiFi transmitters to contend with. There are no clear channels for most people, even assuming the user knows how to optimize their router, which most people don’t.
    I would also explain that I am FCC licensed amateur radio operator K5ZN extra class. I know how radios work and how electromagnetic waves behave. Every diagnostic and symptom tells me there is some incompatibility between my MBPs radio and specifically the Comcast modem-router. In another discussion I gave some technical information about the problem which I spent several day diagnosing while using two different Comcast "Docsis 3" routers.
    I have not seen this WiFi problem when using Airport or other standard routers like Linksys or Netgear. The OP didn’t say what router they are using. My suspicions tell me that Apple is moving in the direction of a very sensitive power-saving radio while ISPs are trying to blast the neighborhoods with powerful WiFi. The result is that my poor Macbook can’t get a good signal.

  • Configuring the time capsule airport wlan function as "connect to wlan", the time caspule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport Express it worked!

    Configuring the time capsule airport wlan function as "connect to wlan", the time capsule gets a correct IP adress from the other wlans IP range, but does not assign this to the ethernet ports. With Airport express it worked, the single Ethernet port got the IP Parameters passed through!
    My setup is a Vodafon Esaybox connected to ISP. Time Capsule is not able to extend the wlan of the easybox, neither airport express can do.
    Only the option "connect to wlan" is succesful.
    With airport express I was able to connect my Sony Bravia TV to the lan via ethernet to stream pictures, the TV set got an IP adress from the easybox.
    With the time capsule the easybox dosn't find devices connected to the ethernet ports to submit IP adresses. The TV set get another IP adress (169.xxx.x.x.) in subnet mask 255.255.0.0 and I don not now where from.
    My notebook is a MacBook pro.
    Any idea????
    Thank a lot in advance!
    Kind regards
    Ingo

    Neverthe less, could there be the chance, that this feature could be implemnented with an firmware update?
    That would appear to be a question for Apple to answer. You can make suggestions to Apple here:
    Apple - AirPort Extreme - Feedback
    If the AirPort Extreme and Time Capsule are configured to "extend a wireless network" they will provide additional wireless coverage....and...the Ethernet ports are enabled in this type of setup.
    The "catch" here is that you must have an Apple router providing the network to be extended.

  • How can I extend the wireless range on my BT Hub 3

    I currently have the BT hub 3 and find that as I have quite a rambling house and the broadband is located at one side rather than in the middle of the house I cannot get a signal in all areas. This is massively frustration for the children when they wish to do their homework in the peace of their own rooms - how can I extend the range, without having to pay through the nose, but easy enough for someone who is not massively technical? - Thanks in advance

    There are a number of options on my website.
    Wireless connection problems
    and
    Network connection problems and possible solutions
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Extend Time Capsule Wireless Range

    I am having trouble with my Time Capsule's wireless range. I am not a networking expert by any means. I own an old building that is 4 stories connected by stairs with thick walls. All the rooms ethernet cables converge in a cubby on the 3rd floor. I placed my Time Capsule in the cubby, but I couldn't receive a wireless signal from the 1st floor. This is ironic because I have an old Netgear G router that sends signals throughout all 4 floors. So I bought an Airport Express to extend my network wirelessly, but the signal has been unstable perhaps because the Time Capsule's wireless signal is too weak. So I want to connect the Airport Express on the 1st floor using the Ethernet link from the 3rd floor Time Capsule which is my main router. From my research, I discovered about WDS networks, which I believe you have to use in order to create a network with multiple Apple base stations linked through ethernet.
    I called Applecare who told me:
    -To connect from Time Capsule to Airport Express using Ethernet, must use WDS network. Setup Airport Express as Relay, NOT Remote.
    -Relay- Direct ethernet connection from Time Capsule to Airport Express, then wireless connection from Airport Express to Macbook.
    -Remote- Wireless signal from Time Capsule to Airport Express, then direct Ethernet connection from Airport Express to Macbook
    I have several questions for you wise people out there:
    1. To extend the Time Capsule wireless network using the Airport Express, but connected directly via ethernet, do I need to setup a WDS network?
    2. I prefer to just use the simple Apple settings "extend network wirelessly". Will this setting only boost a wireless signal received from the Time Capsule? Can it not extend a wireless signal sent directly from Ethernet?
    3. I'm considering getting a Quickertek Triband antenna to place outside the cubby. Anyone have any experience with Airport external antennas?:
    http://www.quickertek.com/products/timecapsuletriband.php
    Any information would be much appreciated! These networking issues have been giving me months of headache.
    Thank you!
    Alexander
    Specs:
    Apple Time Capsule 1TB
    Airport Express N version
    Connected with 2.4ghz. band to N capable Macs.

    Extending your network with an AirPort Express (AX) won't boost the TimeCapsule's (TC's) range per se. It will expand the network's range by adding another transceiver.
    If you'd prefer to avoid using Ethernet to connect the TC and AX, you might get a better signal on the first floor if the AX was on the second floor, i.e, roughly halfway between the TC and the 1st-floor computer. [Extending the range of an 802.11n network|http://docs.info.apple.com/article.html?path=AirPortUtility/5.1/en/ap21 24.html] describes how to configure them.
    If an Ethernet linkup is no problem, though, that should work even better. In this case, it's best to use different (by 3 or more) channels on the 2 stations to reduce the chance that they'll interfere with each other.
    Either way, it's best to use the same network name, network password, and encryption on both stations so you can roam freely through the building without needing to switch manually between them.
    [Designing AirPort Networks 10.5-Windows manual|http://manuals.info.apple.com/enUS/Designing_AirPort_Networks10.5-Windows.pdf] is another good resource you may find helpful.

  • Can I move EA6500 router out of basement to 2nd floor of my house for better wireless range?

    I am having issue with EA6500 wireless range from one end of house to other.  Currently, the EA6500 router is in the basement connected to my SB6141 cable modem.
    Would it be possible to move EA6500 out of basement and to the 2nd floor of my home while keeping modem in the basement.
    I was wondering if I could purchase a switch to place between cable modem and router which would allow me to place the router in closer proximity to my wireless devices.
    I've already tried changing wireless channels and using inSSID but that has not resolved my problem.
    Please let me know.  Thanks.

    It is possible to change the EA6500 router’s location from the basement to the 2nd floor. You need to have a long cable but it should not be 100 meters long since it will cause the connection to drop. It is also advisable to have a wireless AC adapter on our wireless devices/computers to optimize the wireless features of the EA6500 router.
    For your Connected Home, you may use the 2.4 GHz network to connect your wireless devices to surf the Internet and email, share files and print.  The 5 GHz network is best for heavy applications including Voice over IP (VoIP) calls, online gaming, and streaming high-definition videos.

  • MacBook Pro wireless range has suddenly decreased

    I've had my MacBook for almost a year now and the wireless range has been fine. However, a few days ago the wireless started going a bit dodgy - it would sometimes stop working and website would not load. But a quick restart sorted it all out.
    Then, since yesterday it has stopped working completely when I am in my room (where it previously worked find.) But when I move closer to the router it works....
    Does anyone know any fixes or would getting in contact with apple be the best option?
    Thanks in advance,
    SGreenUK
    (Sorry if this has come up before, there are so many problems about networking on the internet I could not find one with my specific problem.)

    Thanks for the reply.
    I changed the channel and then I did a proper reboot of my router ( from within the router settings) and it seems to have fixed everything.

  • E 4200 wireless signal problem

    I've bought a E4200 router because of it's "maximum performance". With the normal settings i have a wireless range of maximum 10 m in the building.  after 5m I've got a low signal.
    I tested a cheap Netgear-router, which had the same range as the E4200 a 125 Euro.
    Is my E4200 broke or is it just a bad buy? The settings are standard (that shouldn't be the problem, I guess!?)

    I live in an area where all the neighbors use the 2.4Ghz band. The signal strength at 2.4Ghz is very good throughout my house but the throughput of the router is poor because of the number of users on that frequency. If two devices are transmitting on the same channel when there is a transmission conflict, the transmissions stop and must be restarted which reduces the throughput. In other words with more users on the 2.4 band there will be more retries no matter what the signal strength.
    I tried the 5Ghz band and discovered that none of the neighbors use it. Great! But the 5Ghz signal strength drops off quickly. Initially I had the router on the first floor at one end of the house with the SmartTV (which has a WiFi capability) on the second floor bedroom at the other end of the house. If I selected the 5Ghz band, the TV could not receive enough signal to connect. With the 2.4 Ghz band the signal strength was good but the throughput was low and internet video was jittery.
    As an experiment I moved the router to the center of the basement on a table. I configured it as a 5Ghz Access Point (bridge mode). I used the router provided by the ISP for routing the hardwired ethernet connections. I now have good signal strength at 5Ghz everywhere in the house. The distance from the router to the TV is about 12 feet less than when the E4200 was on the first floor. And there is more wood flooring and walls between the router and the TV. 
    I believe the signal pattern of the E4200's antennas' is likely a vertical cone pattern. In other words signal strength seems weaker if the router is on the same level as or at a steep angle to the router. But if the router is below or above the recieving device then a stronger signal is received. Of course this is conjecture based on my experience playing with the location of my router in my one case.
    Steve

  • I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?

    Hi
    I am experiencing wireless connection problem on 4s after ios 8.1 upgrade. The wireless icon appears showing that it's connected but webpages do not load. I have checked my internet connection with other devices and seems to be alright. what to do?
    I have tried reseting the network settings and forgetting my wireless connection and re-connecting to it. I even backed up my phone on itunes and restored it, factory reseted it. Nothing seems to work.
    Also after my upgrade to ios 8.1 my personal hotspot option under cellular data has disappeared.
    Would you please help me out? I would really appreciate it.

    Hi..
    Restart your router then restart the iPhone to test.
    If that doesn't help, try this support article >   iOS: Troubleshooting Wi-Fi networks and connections

Maybe you are looking for

  • How to print from Macbook Pro on a Cannon MP610 printer?

    I have recently bought a Macbook Pro, and I have a wireless network set up at home. I have no problems connecting to the internet or the network. But I can't seem to access the printer. I have a Cannon MP610 Printer. This printer is connected to the

  • Button displayed with wrong size in gridbag layout

    I am having a slight problem with gridbiglayout as it is not diplsying one of my buttons properly. The code for my panel is given below. A screenshot of the ouput from my program can be seen at http://i54.photobucket.com/albums/g117/vamega/Program%20

  • Brush cursor resets to crosshair

    No matter what I set the brush cursor to, it intermittantly decides to redset itself to just a crosshair, very awkward when I need to see the size of the brush Im using It will sometimes go back to a normal size brush  cursor if I play with another p

  • How do I make an incremental backup of my PE11 catalog?

    I performaned a backup on 12/6/2013,  The backup folder name is "13-1206 PE 11 Backup".  It is located on an external 1TB drive. Today I added a number of files to the catalog.  Now I am trying to do an incremental backup. My 1st step is to ogen the

  • I updated my mac and now i cant download

    I just updated the software on my computer and now i cant download adobe and silverlight on the internet. It says they are both installed but i cant use any applications that need them. I have been able to use all programs that have used these items