Brocade silkworm 2800 and Storedge A5200 devices not available
First time setup/config on:
2 E4500's
1 Brocade Silkworm 2800
1 Storedge A5200
I can get to the Brocade WEBTOOLS and see the disks (WWN's) and config alias' and zones. I also used the "install_it" script to install SFS 4.4 on the 4500's and restarted them. However, cfgadm -al does not show the fc-fabric devices. Any ideas?
lights are on, ports autoconfiged to L on the Brocade. "luxadm probe" replies, No FC devices found.
Thanks
Bob
Thanks, that was it.
Another question if I might. I added an additional switch and A5200. Both switches have quickloop enabled. Now the format command is show 67 disks on each system. Since 2 are internal, that leaves 65 dev configs from the 2 5200's. Seems odd to me 32 are c3t??d?? and 33 are c4t??d??.
Is this normal or do I have something goofed up? (putting my money on the goofed up part)
Thanks,
Bob
Similar Messages
-
I am starting a new thread because the old one was marked as resolved and it isn't.
My Windows XP desktop is no longer seeing my BB Storm Media Card. I am getting the error:
"Device Memory and Media Card are not available because the Mass Storage is currently in use."
I have followed these directions:
Options > Memory >
Media Card Supoport - ON
Media Transfer Protocol (MTP) - ON
Mass Storage Mode Support - ON
Auto Enable Mass Storage Mode When Connected - YES
SAVE
I have application free pace 8.1 MB
and the error message:
"Device Memory and Media Card are not available because the Mass Storage is currently in use."
The card is there and is seen by my BB Storm. Media > Explore
I have removed and reinstalled the card.
On the desktop I have tried Explore as well as Disk Management and nothing shows up for the Media Card although the Blackberry itself is present.
Please help.Hi there!
Give this KB a try perhaps?
KB19717 The BlackBerry smartphone is not detected as a USB Mass Storage Device when connected to a computer
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
HT6337 Allow handoff between this mac and your iCloud devices not showing up in general preferences
Is anyone not seeing this? the Allow handoff between this mac and your iCloud devices not showing up in general preferences
Imac 2011 21" mid 2011nevermind, Just figured out that my iMac does not support it. Thanks Apple, once again coming up with stupid functionality that only works when you pay more money. 3yr old machine, I guess I need to send it to scrap heap.
-
Hi,?Hope this is an easy one but i'm going round in circles. I have installed my X-Fi Platinum card into my machine, installed drivers. But no sound. When I inspect the Audio Console?It says?Wave Device:Not Available?MIDI DeviceSB X-Fi Synth A [EC00]?Mixer DeviceSB X-Fi Mixer [EC00]?In device manager it's fine no conflict?I have bios disabled the on board soundcard, I think it is something simple but I just can't find the solution. Thanks
I just tried this and it has not worked. I am getting an error message though:The ordinal 6663 could not be located in the dynamic link library MFC42.DLL
?I have previously tried the following?
upgraded drivers to latest revision<
reinstalling drivers twice<
deleting device from Device Manager and rediscovering then installing new drivers<
swapping PCI slot testing, then after fail reinstalling drivers<
disabled other sound devices in Device Manager<
Creative Diagnostics crashes, I would like to flush every trace of the creative suite (all versions and?every registry entry) from my system and start with a fresh install, I realy think this may turn out to be a nasty one.
?Message Edited by markedwards_uk on 2-0-200703:45 PM -
I have created a PDF and password protected it for view. However, when reading the PDF in Adobe Reader app on the iPad the commenting and annotation options are not available. Is there a way to allow commenting and annotation in the app while password protecting the document?
Is there a setting that needs to be set to allow the annotation features? I set password protection to open and then password for editing and set it to Any except page extraction, but it still did not give the annotation option
-
i changed companies and had icloud with my old company - now i want to just use my personal id and can't change any icloud info to match my personal ipad id - i can't delete the icloud without the old company id and password which is not available to me - it probably doesn't even exist anymore!
Because I can't delete the icloud account, I keep getting view terms to accept and it wants to go to the old company account. I can't do anything to get rid of this - when I try to delete the icloud it wants me to delete find my ipad and asks for the old co. id and password - it's a vicious circle and i just want to get rid of it and start fresh with my regular personal email id and password!!! Help!You will need that old Apple ID and password, which does indeed still exist. Apple doesn't delete Apple IDs, though if this ID was in the control of your company they may have changed the password. If so, you will need your former company to log into the iCloud account using that ID and password and erase the iPad or remove it from iCloud:
http://support.apple.com/kb/TS4515?viewlocale=en_US
Until that's done you cannot change those settings, and if you try to restore the iPad will have it locked with Activation Lock and thereafter be unusable.
Regars. -
HT4059 Why Indian authours and Indians books are not available in your iBooks store.
Why Indian authours and Indians books are not available in your iBooks store.
Thats because Indian publishers may have not signed an agreement with Apple. Worst part is even if I want to publish a book for free using official iBooks Author, it does not publish on Indian iBooks Store.
-
Icm trace level if smicm and SAP MMC are not available ( CE system on Unix)
Hi Experts,
Could you please let me know how will I increase the icm trace level if SMICM transaction code and SAP MMC are not available.
I have an CE 7.2 system running on HP UNIX.
Thanks and Regards
Syamhttp://help.sap.com/saphelp_nw70/helpdata/en/0b/6aedff404d6b4a8cac8f1359e1b47c/frameset.htm
kill -USR2 <pid>
Markus -
I try to update from version 4.1, but it shows in ITunes device not elligible. I have the latest version of ITunes, but it seems the phone is a problem. None of the aplications work properly, Facebook and Safari cut off....
If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 6.1. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
iOS 5: Updating your device to iOS 5 or Later
http://support.apple.com/kb/HT4972
How to install iOS 6
http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
Tip - If connected to your computer, you may need to disable your firewall and anitvirus software temporarily. Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 6.x, the next update can be installed via wifi (i.e., not connected to your computer).
Cheers, Tom -
iphone 4 - yesterday it popped up to update to IOS7.... now it is froze on the screen as a picture (one end of connection with arrow up to itunes written out to itunes icon"..... ive tried restoring and it says "the iphone "iphone" could not be restored. Device not found".... although i do have it connected to my puter and have itunes activated.
i wished some one have warned me about this mess...
JudyiOS: Unable to update or restore
-
Froze up and then boot device not found
Opened Up Sleekbook, Was Trying To Look At A page Already Open And Exit Out Of Another. Page Did Not Respond. Asked To Recover Webpage. Did Not Respond. Tried Ctrl,Alt,Delete...Nothing So HIt Power Button. Turned Back O. After 10Seconds. Black Screen Says Boot Device Not Found. What Do i Do?
Go into either F2 (UEFI diagnostics) or F10 (BIOS) as you power up and look for a hard drive diagnostic and run it. Best bet is your hard drive crashed and needs replacement. What kind of Sleekbook? We need that information to tell you how to proceed.
-
HT204074 manage devices not available
I am not able to see the option to manage my devices when I am in the View my account settings in iTunes.
i have this too and i think i understand why. Even though your computer is authorized for your apple ID, and your other devices are set up with your apple ID's, none ot them have iTunes "associated with" your apple ID's because you haven't activated iTunes Match nor have you done any "automatic download", nor have you re-downloaded a previsouly purchased (and previously downladed) item. Only of these "iTune in The Cloud" feature would trigger the association and the 90-day lock out.
It also seems that the "Transferring Purchase" from device to computer does NOT trigger the association neither. (it didnt on my computer). -
When i rip a cd I only get 1min19secs on the 1st song and the rest says not avail.
when I rip a cd I only get 1min19secs of the 1st song and the rest of the songs sats that its not avail.
"Message" usually means a text message. I suspect you mean email messages. If so, and the email account you use is IMAP, then you can't delete an email on a device but not on the server - that's the way all IMAP services work. If the account is POP, and if the email service provides this, then there should be a setting in your email settings for that account to NOT delete from the server.
If you really mean a text message, then how it works is designed by your carrier. -
Remove bluetooth device - device not available
I have a iPhone 5 and recently traded in a car that was paired via bluetooth. I did not think to undo the pairing prior to saying goodbye.
I know it is not a big issue and won't mess with the new vehicle, but I just like things neat and tidy and would like to remove it from the list.
The real stinky thing about it is that both vehicles are the same model and I now have two items in the list with the same name and only one is valid.
Any way to delete it?I was attempting to remove the device from the list on the phone. For some reason I could not do that when selecting the device. It would not go to the that next screen. This is while I was connected to the new vehicle.
Once I was away from the vehicle, where it could not connect, I was able to access that additional screen and forget the device. I did this before I saw your response. But you are absolutely correct. I would just add a caveat to not have any connection with any bluetooth device while attempting to forget another device unless of course it is the device that you are currently connected to.
Chris - Thank you for your response -
T61 - directdraw and agp texture acceleration not available
hi i have a problem with directx i think
os: winxp sp3
on dxdiag:
in the display tab - i get on directdraw and on the agp accelaration not available, and i cant enable them
the direct3d is enabled.
next to the direct draw and the directt3d there is the test button, when i press it -
the direct draw test pass
direct3d fail on 1st test
i tried to:
reinstalled directx 9c
install the lastest display driver from lenovo (vga card- intel 965 gm)
remove all codecs (xvid,divx, etc..) and install them back.
but i dont really get a clue how to solve this.
this is a problem for me as i can't watch movies correctly on my media player (and any other player, like vlc)
- i c squares in xvid/ divx files (which i compiled on other computer)
- on av-dvi files i c lines (got the movie out of a dvi camera using windoes movie maker and a firewire cable)
note: both of the files runs smoothly on my other computer, and the same codecs are installed on both oof them
pls advise on how to solve this problem.
thank you.
here is the log file which i get from the dxdiag tool:
http://rapidshare.com/files/236263295/DxDiag.txt.html
Message Edited by dror on 05-23-2009 02:50 AM
Message Edited by dror on 05-23-2009 02:54 AMPlease give us some more information...
Why do you think the stated forms of Acceleration are not available? Where are you getting this information from?
Please take a look at the Windows Device Manager. What Display Adapter do you have, and at what level is its driver?
Centex
Maybe you are looking for
-
HT5148 how many computers can I install final cut on?
Me and my business partner are looking to purchase Final Cut X for our company. Can you purchase one copy and use one both computers?
-
Hello!! I have a problem with the transaction MIRO, trying to change the G/L account, the system displays all associated accounts, including those that are associated accounts receivable and when I try to change the associated account of the vendor b
-
Here's an example: Several people are working on a PSD mockup of, say, a website. Inside this mockup are icons, already appropriately placed & spaced on the page. Then, we get feedback that one of the icons needs to be different. So, we update the ic
-
Use of ECC 6.0 with PI 7.0 server?
use of ECC 6.0 with PI 7.0 server? what are the requirements for uploading wsdl and Tpz files from service Market Place to PI 7.0 server?
-
Add Event Receiver on Existing List in SandBoxed Solution
Hi Guys, I have Created One Event Receiver which is of type SandBox Solution and now i am programatically adding Event Receiver to a Specific List Instance Which is Existing on Site.But SPEventReceiverDefinitionCollection.Add() method is NOT availabl