Brtools recovery - restart possible?

Hello,
If you are using brtools for recovery, and while you are restoring datafiles from tape your unix session dies, is it possible to open a new unix session and proceed with brtools and the recovery/restore at the moment of the failure?
An example whould be a 2 Terabytes database recovery process, where the restore of the datafiles might take hours and you can only work remotely.
Thanks

Hi
It sounds like you need "GNU screens". It's an ASCII terminal emulator which allows you to open multiple windows through the one telnet connection. The best thing is that if you lose your connection, you can RECONNECT to your previously running Screen (like terminal server sessions only ascii based).
Here is a link to a Screen Introduction Page :
http://www.kuro5hin.org/story/2004/3/9/16838/14935
Regards
Doug

Similar Messages

Set Message in BPM to System Error - Manual Restart Possible ?

Hello,
I'm working on a scenario where two idocs are merged in a BPM. The next step is sending the message in a synchronous RFC (BAPI) to a SAP R/3. Is it possible to set the merged message to the message status 'System Error - Manual Restart Possible' in the SXMB_MONI, when the BAPI returns an Error message?
When it's not possible, is there an othe possibility to sent the message again, without involving the source system?
Thanks in advance
Matthias

Hi,
It would be better i think if you use the concept of raising an exception in your response mapping
please refer:
/people/alessandro.guarneri/blog/2006/01/26/throwing-smart-exceptions-in-xi-graphical-mapping
/people/michal.krawczyk2/blog/2007/04/26/xipi-throwing-generic-exceptions-from-any-type-of-mapping
in the response mapping you can check the condition for the responce code from RFC.
Ranjit

URGENT: system error - Maual restart possible

Hi Experts,
I'm facing a problem in Xi prodoction. Both inbound and outbound are throwing system error - Maual restart possible. The user is restarting manually in order to post the invoice.
Basically this is retail project, from POS s/w to Xi to SAP R/3. The scenario is file to idoc(inbound) and idoc to file (outbound).
The error is :
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="PERSIST">MESSAGE_NOT_FOUND</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>XML message not found</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
The acknowledgement error is :
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIAdapter</SAP:Category>
<SAP:Code area="IDOC_ADAPTER">ATTRIBUTE_INV_SND_SERV</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Unable to convert the sender service to an ALE logical system</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
I have gone throw the sdn post and blogs but i'm uable to trace the problem.
Kindly suggest me ASAP as this is business critical and posting have been stoped.
Regards,
Pawan

Hi,
Please find the interface determination trace. Hope this will help you to provide some suggestion.
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Trace xmlns:SAP="http://sap.com/xi/XI/Message/30">
<Trace level="1" type="B" name="IDX_INBOUND_XMB" />
- 
<Trace level="1" type="T">User: XIBGUSER</Trace>
<Trace level="1" type="T">Language: E</Trace>
<Trace level="1" type="T">ALE-AUDIT-IDoc-Inbound Handling</Trace>
<Trace level="1" type="T">IDoc-Inbound-Handling</Trace>
<Trace level="2" type="T">Tunneling needed?</Trace>
<Trace level="2" type="T">Partytype = LS fallback to logical system</Trace>
<Trace level="3" type="T">Sender Interface</Trace>
<Trace level="3" type="T">WP_PLU.WP_PLU03 urn:sap-com:document:sap:idoc:messages</Trace>
<Trace level="1" type="T">Syntax-Check-Flag X</Trace>
<Trace level="1" type="T">IDoc-Tunnel-Flag</Trace>
<Trace level="1" type="T">Queueid</Trace>
- <Trace level="1" type="B" name="IDX_IDOC_TO_XML">
<Trace level="1" type="T">Get the Metadata for port SAPRT2</Trace>
<Trace level="2" type="T">----
</Trace>
<Trace level="2" type="T">IDX_STRUCTURE_GET Details</Trace>
<Trace level="2" type="T">Port : SAPRT2</Trace>
<Trace level="2" type="T">IDoctyp : WP_PLU03</Trace>
<Trace level="2" type="T">Cimtyp :</Trace>
<Trace level="2" type="T">RFCDest :</Trace>
<Trace level="2" type="T">Release : 700</Trace>
<Trace level="2" type="T">Version : 3</Trace>
<Trace level="2" type="T">Direct : 1</Trace>
<Trace level="2" type="T">SAPREL : 700</Trace>
<Trace level="2" type="T">----
</Trace>
<Trace level="1" type="T">Convert Segment-Definitions to Types</Trace>
<Trace level="1" type="T">Make Syntax check of actual Idoc</Trace>
<Trace level="2" type="T">----
</Trace>
<Trace level="2" type="T">IDX_SYNTAX_CHECK</Trace>
<Trace level="2" type="T">Port : SAPRT2</Trace>
<Trace level="2" type="T">IDoctyp : WP_PLU03</Trace>
<Trace level="2" type="T">Cimtyp :</Trace>
<Trace level="2" type="T">----
</Trace>
<Trace level="2" type="T">Create XML-Control Record</Trace>
<Trace level="2" type="T">Create XML-Data Records</Trace>
<Trace level="3" type="T">Create data Record E1WPA01</Trace>
<Trace level="3" type="T">Create data Record E1WPA02</Trace>
<Trace level="3" type="T">Create data Record E1WPA03</Trace>
<Trace level="3" type="T">Create data Record E1WPA04</Trace>
<Trace level="3" type="T">Create data Record E1WPA05</Trace>
<Trace level="3" type="T">Create data Record E1WPA01</Trace>
<Trace level="3" type="T">Create data Record E1WPA02</Trace>
<Trace level="3" type="T">Create data Record E1WPA03</Trace>
<Trace level="3" type="T">Create data Record E1WPA04</Trace>
<Trace level="3" type="T">Create data Record E1WPA05</Trace>
<Trace level="3" type="T">Create data Record E1WPA01</Trace>
<Trace level="3" type="T">Create data Record E1WPA02</Trace>
<Trace level="3" type="T">Create data Record E1WPA03</Trace>
<Trace level="3" type="T">Create data Record E1WPA04</Trace>
<Trace level="3" type="T">Create data Record E1WPA05</Trace>
<Trace level="3" type="T">Create data Record E1WPA01</Trace>
<Trace level="3" type="T">Create data Record E1WPA02</Trace>
<Trace level="3" type="T">Create data Record E1WPA03</Trace>
<Trace level="3" type="T">Create data Record E1WPA04</Trace>
<Trace level="3" type="T">Create data Record E1WPA05</Trace>
</Trace>
<Trace level="2" type="T">Partytype = LS fallback to logical system</Trace>
<Trace level="2" type="T">Set Sender Routing-object</Trace>
<Trace level="1" type="T">Set Receiver Routing-object</Trace>
<Trace level="1" type="T">Exit Function IDX_INBOUND_XMB</Trace>
<Trace level="1" type="T">COMMIT is expected by application !</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-ENTER_XMS" />
- 
<Trace level="1" type="B" name="CL_XMS_MAIN-SET_START_PIPELINE" />
- 
<Trace level="3" type="T">XMB was called with external pipeline PID = ENTRY</Trace>
<Trace level="3" type="T">Getting type of XMB...</Trace>
<Trace level="1" type="B" name="SXMBCONF-SXMB_GET_XMB_USE" />
<Trace level="2" type="T">XMB kind = CENTRAL</Trace>
<Trace level="3" type="T">Start pipeline found</Trace>
<Trace level="2" type="T">Switch to external start pipeline PID = CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_TROUBLESHOOT-ENTER_PLSRV">
<Trace level="3" type="T">No triggers found. OK.</Trace>
</Trace>
<Trace level="1" type="T">****************************************************</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">XMB entry processing</Trace>
<Trace level="3" type="T">system-ID = XIP</Trace>
<Trace level="3" type="T">client = 600</Trace>
<Trace level="3" type="T">language = E</Trace>
<Trace level="3" type="T">user = XIBGUSER</Trace>
<Trace level="1" type="Timestamp">2008-03-27T06:35:02Z UTC-7</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">* *</Trace>
<Trace level="1" type="T">****************************************************</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_UC_EXECUTE" />
- 
<Trace level="1" type="T">Message-GUID = DCFBC7EA238100F1B64A00145EDC94EF</Trace>
<Trace level="1" type="T">PLNAME = CENTRAL</Trace>
<Trace level="1" type="T">QOS = EO</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PIPELINE_ASYNC" />
- 
<Trace level="3" type="T">QOS = EO</Trace>
<Trace level="3" type="T">Message-GUID = DCFBC7EA238100F1B64A00145EDC94EF</Trace>
<Trace level="1" type="T">Get definition of external pipeline = CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-LOOKUP_INTERNAL_PL_ID">
<Trace level="3" type="T">External PLID = CENTRAL</Trace>
<Trace level="3" type="T">Internal PLID = SAP_CENTRAL</Trace>
</Trace>
<Trace level="1" type="T">Get definition of internal pipeline = SAP_CENTRAL</Trace>
<Trace level="3" type="T">Generate prefixed queue name</Trace>
<Trace level="1" type="T">Queue name : XBTI0001</Trace>
<Trace level="1" type="T">Generated prefixed queue name = XBTI0001</Trace>
<Trace level="1" type="T">Schedule message in qRFC environment</Trace>
<Trace level="3" type="T">Setup qRFC Scheduler</Trace>
<Trace level="1" type="T">Setup qRFC Scheduler OK!</Trace>
<Trace level="3" type="T">Call qRFC .... MsgGuid = DCFBC7EA238100F1B64A00145EDC94EF</Trace>
<Trace level="3" type="T">Call qRFC .... Version = 000</Trace>
<Trace level="3" type="T">Call qRFC .... Pipeline = CENTRAL</Trace>
<Trace level="3" type="T">OK.</Trace>
<Trace level="1" type="T">----
</Trace>
<Trace level="1" type="T">Going to persist message</Trace>
<Trace level="1" type="T">NOTE: The following trace entries are always lacking</Trace>
<Trace level="1" type="T">- Exit WRITE_MESSAGE_TO_PERSIST</Trace>
<Trace level="1" type="T">- Exit CALL_PIPELINE_ASYNC</Trace>
<Trace level="1" type="T">Async barrier reached. Bye-bye !</Trace>
<Trace level="1" type="T">----
</Trace>
<Trace level="3" type="T">Version number = 000</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- 
<Trace level="3" type="T">Persisting message Status = 001</Trace>
<Trace level="3" type="T">Message version 000</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
<Trace level="1" type="T">--start sender interface action determination</Trace>
<Trace level="1" type="T">select interface WP_PLU.WP_PLU03*</Trace>
<Trace level="1" type="T">select interface namespace urn:sap-com:document:sap:idoc:messages</Trace>
<Trace level="1" type="T">no interface found</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-PERSIST_READ_MESSAGE">
<Trace level="3" type="T">Trace object available again now. OK.</Trace>
<Trace level="3" type="T">Message was read from persist layer. OK.</Trace>
<Trace level="3" type="T">Message properties in XMB object were setup. OK.</Trace>
<Trace level="3" type="ToDo">Make sure we catch exceptions in persist read</Trace>
<Trace level="3" type="ToDo">Tracing obj. not avail. before return of CL_XMS_MAIN-PERSIST_READ_MESSAGE</Trace>
</Trace>
<Trace level="1" type="T">Note: the following trace entry is written delayed (after read from persist)</Trace>
<Trace level="1" type="B" name="SXMS_ASYNC_EXEC" />
- 
<Trace level="3" type="T">message version successfully read from persist version= 000</Trace>
<Trace level="2" type="T">Increment log sequence to 001</Trace>
<Trace level="1" type="T">----
</Trace>
<Trace level="1" type="T">Starting async processing with pipeline CENTRAL</Trace>
<Trace level="3" type="T">system-ID = XIP</Trace>
<Trace level="3" type="T">client = 600</Trace>
<Trace level="3" type="T">language = E</Trace>
<Trace level="3" type="T">user = XIBGUSER</Trace>
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7</Trace>
<Trace level="1" type="T">----
</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PIPELINE_SYNC" />
- 
<Trace level="1" type="T">Get definition of external pipeline CENTRAL</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-LOOKUP_INTERNAL_PL_ID">
<Trace level="3" type="T">External PLID = CENTRAL</Trace>
<Trace level="3" type="T">Internal PLID = SAP_CENTRAL</Trace>
</Trace>
<Trace level="1" type="T">Corresponding internal pipeline SAP_CENTRAL</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline attributes</Trace>
<Trace level="3" type="T">PID = SAP_CENTRAL</Trace>
<Trace level="3" type="T">ENABLE = 1</Trace>
<Trace level="3" type="T">TRACELEVEL = 0</Trace>
<Trace level="3" type="T">EXEMODE = A</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline elements</Trace>
<Trace level="3" type="T">ELEMPOS = 0001</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0002</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0003</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_MESSAGE_SPLIT</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0004</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_REQUEST</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0007</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_OUTBOUND_BINDING</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0008</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_CALL_ADAPTER</Trace>
<Trace level="3" type="T">PLSRVTYPE = =SWITCH=</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">ELEMPOS = 0009</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_MAPPING_RESPONSE</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">FL_DUMMY =</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T" />
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7 Begin of pipeline processing PLSRVID = CENTRAL</Trace>
- <Trace level="1" type="B" name="PLSRV_RECEIVER_DETERMINATION">
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7 Start of pipeline service processing PLSRVID= PLSRV_RECEIVER_DETERMINATION</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_RECEIVER_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_RD_PLSRV</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_RD_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">R E C E I V E R - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
<Trace level="2" type="T">Start without given receiver</Trace>
<Trace level="2" type="T">Classic Receiver Determination via Rules.</Trace>
<Trace level="2" type="T">Check conditions for rule line no. 1</Trace>
<Trace level="2" type="T">...valid Receiver w/o Condition: - e_solutionsPOS</Trace>
<Trace level="2" type="T">No Receiver found behaviour: 2</Trace>
<Trace level="2" type="T">Number of Receivers:1</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7 End of pipeline service processing PLSRVID= PLSRV_RECEIVER_DETERMINATION</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">Persisting message after plsrv call</Trace>
<Trace level="3" type="T">Message-Version = 001</Trace>
<Trace level="3" type="T">Message version 001</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</Trace>
- <Trace level="1" type="B" name="PLSRV_INTERFACE_DETERMINATION">
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7 Start of pipeline service processing PLSRVID= PLSRV_INTERFACE_DETERMINATION</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV">
<Trace level="3" type="T">Calling pipeline service: PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">Reading Pipeline-Service specification...</Trace>
<Trace level="3" type="T" />
<Trace level="3" type="T">Pipeline service specification (table SXMSPLSRV)</Trace>
<Trace level="3" type="T">PLSRVID = PLSRV_INTERFACE_DETERMINATION</Trace>
<Trace level="3" type="T">PLSRVTYPE =</Trace>
<Trace level="3" type="T">ADRESSMOD = LOCAL</Trace>
<Trace level="3" type="T">P_CLASS = CL_ID_PLSRV</Trace>
<Trace level="3" type="T">P_IFNAME = IF_XMS_PLSRV</Trace>
<Trace level="3" type="T">P_METHOD = ENTER_PLSRV</Trace>
<Trace level="3" type="T">FL_LOG =</Trace>
<Trace level="3" type="T">FL_DUMMY = 0</Trace>
<Trace level="3" type="T" />
- <Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL">
- <Trace level="1" type="B" name="CL_ID_PLSRV-ENTER_PLSRV">
<Trace level="1" type="T">I N T E R F A C E - D E T E R M I N A T I O N</Trace>
<Trace level="1" type="T">Cache Content is up to date</Trace>
<Trace level="2" type="T">Check conditions for (Inb: Party Srvc If) e_solutionsPOS WP_PLU.WP_PLU03</Trace>
<Trace level="2" type="T">...valid InbIf without Condition: WP_PLU.WP_PLU03</Trace>
<Trace level="2" type="T">Number of receiving Interfaces:1</Trace>
</Trace>
</Trace>
</Trace>
<Trace level="1" type="Timestamp">2008-03-27T06:35:03Z UTC-7 End of pipeline service processing PLSRVID= PLSRV_INTERFACE_DETERMINATION</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">Persisting message after plsrv call</Trace>
<Trace level="3" type="T">Message-Version = 002</Trace>
<Trace level="3" type="T">Message version 002</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">Persisting message after plsrv call</Trace>
<Trace level="3" type="T">Message-Version = 002</Trace>
<Trace level="3" type="T">Message version 002</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</Trace>
<Trace level="3" type="System_Error">Error exception return from pipeline processing!</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- 
<Trace level="3" type="T">Persisting message Status = 014</Trace>
<Trace level="3" type="T">Message version 002</Trace>
<Trace level="3" type="T">Pipeline CENTRAL</Trace>
</SAP:Trace>
Thanks,
Pavan

How to cancel automatically messages stated 17 (Application error - manual restart possible) in SAP ECC

Hi people. I need to create a job to cancel automatically the messages with the status 17 (Application error - manual restart possible) in SAP ECC.
In SXI_MONITOR I can retrieve these messages filtering just for "Application Error". I can cancel them here, however I need for a Job to do it.
I appreciate your help.
Regards
Arturo Santos

Hi,
>Is there any way we can make this automatic
In RWB-Component Montoring-Adapter Engine-Communication Channel Montoring- Select the Adapter- Go to Settings and change as per your Business Requirement.
Regards
Agasthuri Doss

Notifications of XI-mgs in status 'System Error - Manual Restart Possible'

Dear colleagues,
I'm using a simple communication channel of type 'GeneratedReceiverChannel_XI' in order to push XML-messages from the intergration engine into the ABAP-Backend using an ABAP server proxy. Many of these messages, however, show an error status in the XI-monitor (Notifications of XI-mgs in status 'System Error - Manual Restart Possible'). The indication of the system error is OK, since the XML-parser correctly detects a character in a field which shall be mapped to a field of type 'DEC' in the ABAP backend.
Is there any possibility to configure some type of alerting in the ABAP-backend to track especially the appearence of XML-messages in the XI-monitor with status 'System Error'?
Thanks a lot and kind regards
Stefan

HI,
As its mentioned in above postes, you can configure the Alert notification in XI which can give you the alerts about this kind of errors.
If the exception is raised after reaching to ABAP backend R/3 Side, then you may trace it in t-code SXMB_MONI of R/3.
Refer -- ALERT MANAGMENT
http://help.sap.com/saphelp_nw04/helpdata/en/3f/81023cfa699508e10000000a11402f/content.htm
Thanks
Swarup

Computer Restarting possibly due to DCHP and DirectoryServices?

I'm not sure this is the right forum -
My computer has restarted 2 times -(on it's own)
The problem seems to lie , possibly, in Directory Services and DCHP
Could someone please clarify what this could mean

Thank you for replying 'I love my macbook'
No my computer did not crash - I was in the internet (both times - just web surfing and my computer just went black and restarted on its own -
It went right on to the desktop.
The problem seem to be somewhat connected to DCHP - maybe and the start-up of Directory services.
I wanted someone to clarify what importance these things are and are they connected to Leopard - What is DCHP and Directory Services?

SMF - start at boot time, but don't restart - possible?

I'm setting up a software package that has a number of background processes.
I've got SMF manifests created and imported for all of them, and they're working great for starting the processes at boot time, and doing the automatic restarts when one fails.
Here's my problem. It turns out that the users of this software want to be able to use the software's integrated process control methods to stop some of their processes. With the current configuration, they use the software's method to stop one of it's processes, and SMF promptly restarts it.
Is there a way to set up SMF managed software so that SMF starts it at boot time, but then doesn't care if stops later?
Richard

I'm not sure how it would be SMF "managed" in such a case. Obviously you want the management to be elsewhere.
You could use the "legacy" startup scripts in /etc/rcX.d. That will start a process and forget about it, just like pre-Solaris 10. You don't use manifests or have any other benefits of SMF.
If you do want SMF, I guess the question is how you want it to act..
When the users stop the processes, do you want SMF to say enabled or disabled? SMF does not track enabled processes by periodic polling, it does it by tracking contracts. This means that starting a process outside of SMF does not allow SMF to track it.
Darren

IMac G5 restarting- possible power fault????

Hey,
My iMac G5 2.0GHZ 20" is restarting itself, sometimes within a few seconds, a few minuites or a few hours.
I have looked up my serial number under the returns program and my serial is -W852000ESDZ.
I believe my G5 is a second generation but this serial number matches except for the W852 '0' being a '2'???
Any help or suggestions would be great.... is it worth me contacting Apple?
My G5 is just outside the 1 year warrenty, by 6 weeks
-Andrew

Well I took the trip to Manchester but was told a different thing to Apple on the telephone. They told me that my iMac won't be covered under that program and that the repairs could cost me upto £700??
Any suggetions and who I can speak to get the correct info.. thanks for the help so far!!
Andrew

S10-3S: BIOS Update issue - Recovery procedure possible ?

Dear all,
yesterday i flash the new Bios "LM30_0128 / 38CN11WW" into my S10-3S (Memory compatibility Bios)
under Windows 7-Home 32Bit.
The Bios routine runs and after a while, the Ideapad booting self. But now, i only see a black screen after
PowerSwitch on. No Bios beep. No Infos. Nothing ! Only the 3left LEDs are white ! The Screen is death !
So i research the Lenovo Forums about to fixing this.
I found a lot of Informations about the BIOS Recovery Procedure and try different versions about that.
I create the "Crisis" Emergency Floppy /USB Stick with the Files inside the "LM30_0128.exe". No Problems !
I try USB Floppy and USB Stick but nothing happens if i press the different Keyboard Combinations:
FN+F, FN+R, FN+ESC, FN+B, Windows+F, Windows+R, Windows+ESC, Windows+B . No access
to floppy or USB Stick ! No Boot Process. Nothing !
Knows anybody the Keyboard Code to go inside the Bios Recovery Process ?
Thanks you very much
SkyHawk

Hi did you try this from Ideapad Knowledge Base ...
if that doesnt help , please give a bit time , so we can look for a solution in case of bricked s10-3s..
Meanwhile dont update to new BIOS for S10-3s.
if isnt clear whats going on with S10-3s.
Sorry for this awkwardness
sincerely KalvinKlein
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

FROZEN SCREEN, no hard restart possible

While watching a YouTube video, my iPad froze. Holding down SLEEP button does nothing; nor does START button, or holding both. Any suggestions?

After some searching around, I found this answer on apple.com/expert:
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds.

Data Recovery - Failed HD on 2010 MacBook Pro

Hello, I have had a HD failure, or at least what I believe to be one on my 2010 MacBook Pro. I updated to Mavericks from Snow Leopard in October and everything appeared to run smoothly. 2 days ago I was watching a video in Itunes I my entire system froze, however the mouse was still moveable as was the dock. Rather stupidly, i tried to load a couple of applications, they did eventually load, but were not function able. The pinwheel kept spinning, and trying to move the page windows only resulted in lag. The system then crashed completely, and I had to restart. It would not go past the grey screen with the apple logo.
For the past day I`ve tried on and off everything that I know how to do. PRAM and SMC resets, Apple Hardware disk (which resulted in an issue with one of my memory sticks. I switched them out, ran the test again, and the system simply crashed part way through), and Disk utility. After running Verify and Repair permissions/disk permission in Disk Utility, I received the message relating to an "uncorrectable error" and "This disk cannot be repaired."
I`ve had issue with this machine on and off for nearly the past two years. Disk utility has appeared resolve the issues, but sometime later something else would crop up. Kernal issues have become more and more frequent as have crashes, and I`ve suspected the HD is to blame. Back in Aug 2012 I had the logic board replaced under warranty, due to graphic issues and problems display games/video or other media and lag. This fixed the issue for a few months, then the kernal problems started and I have frequently (every few days) needed to restart and gotten error messages. The machine will no longer start up, and though most of my date is backed up, some of it is not, and I really would like to get it back. The apple logo will appear on screen for 30sec-1min then crash and automatically restarts.
System Info: 15' 2010 MacBook Pro
2.66GHZ i7
5400rpm HD
etc.
Also, I have tried booting up with the "Shift" key held and the following message has appeared multiple times on the grey/apple logo screen:
panic(cpu 2 caller 0xfffff80189cd7d4): "Process 1 exec of /sbn/launched falled, errno 2"0/SourceCache/xnu/xnu-24422.1.72/bsd/kern/kern_exec.c:3836
Debugger called: <panic>
0xffffff8100e1bdf0 : 0xffffff8018622f69
0xffffff8100e1be7d : 0xffffff80189cb7d4
0xffffff8100e1bef0 : 0xffffff80189ab867
0xffffff8100e1bf20 : 0xffffff80189dfe51
0xffffff8100e1bf50 : 0xffffff8018620b2b
0xffffff8100e1bf80 : 0xffffff80186dc7d3
0xffffff8100e1bfa0 : 0xffffff80186f35d2
BSD process name corresponding to current thread: init
Mac OS version:
Not yet set
Kernel version:
Darwin Kernel Version 13.0.0: Thu Sep 19 22:22:27 PDT 2013; root:xnu-2422.1.72~6/RELEASE_X86_64
Kernel UUID: 1D9369E3-D0A5-31B6-8D16-BFFBBB390393
Kernel slide: 0x0000000018400000
Kernel text base: 0xffffff8018600000
System model name: MacBookPro6,2 (Mac-F22586c8)
System uptime in nanoseconds: 4597800225
My primary concern is Data Recovery if possible, then dealing with whatever the issue may be. If the HD is in fact to blame, I can replace it, but I`d really like to get the remain date that is on the drive if possible. Looking through the forums I see that others have had similar issues. I appreciate any help or suggestions that anyone can offer. . Thank you to anyone in advance!

Appfan42,
you’ve now discovered where the value lies in making regular backups — to avoid data loss due to a “single point of failure”. If the data that’s currently only on your hard drive is irretrievable through ordinary means, there is still the possibility of hiring the services of a data recovery company, but their services are typically quite expensive. Should it be necessary for you to purchase a replacement hard drive (or SSD), I’d highly recommend that you also purchase an external hard drive for use as a Time Machine backup destination, so that you can make regular backups, and thus avoid a similar situation at some future date.
That being stated, there is a chance that the problem is due to a faulty internal SATA cable rather than a faulty hard drive. The way to check that would be to purchase either a SATA-to-USB or SATA-to-FireWire adapter or an external disk enclosure, and move your hard disk outside of its usual place within your MacBook Pro. After that, boot into Recovery mode and run Disk Utility from there to verify/repair your drive while it’s external, and see if it will boot normally afterwards. If it behaves itself externally, then that could point to the problem lying with your internal SATA cable; that would also be the right time to perform data recovery and start making regular Time Machine backups.

Raw Recovery?

So my hard drive is asking to re initialize when it has already been formatted and data has been stored. I would like to recover my files it shows its a raw format now so it cant be mounted but shows up in disk utility. does anyone know of a free or good raw data recovery software?

First try the following:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
For now you can skip repairing permissions. If repairing the drive does not help it may still be possible to recover files. See:
Basics of File Recovery
Files in Trash
If you simply put files in the Trash you can restore them by opening the Trash (left-click on the Trash icon) and drag the files from the Trash to your Desktop or other desired location. OS X also provides a short-cut to undo the last item moved to the Trash -press COMMAND-Z.
If you empty the Trash the files are gone. If a program does an immediate delete rather than moving files to the Trash, then the files are gone. Recovery is possible but you must not allow any additional writes to the hard drive - shut it down. When files are deleted only the directory entries, not the files themselves, is modified. The space occupied by the files has been returned to the system as available for storage, but the files are still on the drive. Writing to the drive will then eventually overwrite the space once occupied by the deleted files in which case the files are lost permanently. Also if you save a file over an existing file of the same name, then the old file is overwritten and cannot be recovered.
General File Recovery
If you stop using the drive it's possible to recover deleted files that have not been overwritten with recovery software such as Data Rescue II, File Salvage or TechTool Pro. Each of the preceding come on bootable CDs to enable usage without risk of writing more data to the hard drive.
The longer the hard drive remains in use and data are written to it, the greater the risk your deleted files will be overwritten.
Also visit The XLab FAQs and read the FAQ on Data Recovery.
There are no free data recovery utilities or services.

My Macbook Air crashing and restarting

I get the following error, it happens mainly while browsing with Safari
Anonymous UUID: 03C0D7C0-2689-FD43-3E7E-426F6F7F145C
Sun Oct 19 02:06:53 2014
panic(cpu 1 caller 0xffffff8008adc43e): Kernel trap at 0xffffff8008bc6ffe, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000002918, CR3: 0x000000000a14d001, CR4: 0x00000000001606e0
RAX: 0xffffff80a1fc3c80, RBX: 0xffffff801a900000, RCX: 0x0000000000002900, RDX: 0xffffff8013a918a0
RSP: 0xffffff80a1fc3c50, RBP: 0xffffff80a1fc3cb0, RSI: 0x0000000000000000, RDI: 0xffffff8013a918a0
R8: 0x0000000000000001, R9: 0x0000000000000000, R10: 0x0000000000002000, R11: 0x000000000000034c
R12: 0xffffff801a900052, R13: 0xffffff801a900080, R14: 0xffffff8008f240b6, R15: 0x0000000000000001
RFL: 0x0000000000010202, RIP: 0xffffff8008bc6ffe, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000002918, Error code: 0x0000000000000002, Fault CPU: 0x1

Try repairing your disk
Repair your disk
To start your computer from Recovery, restart your Mac and hold down the Command and R keys at startup.
select Disk Utility from the OS X Utilities pane, and then click Continue.
Select the disk or partition from the list on the left, and then click the First Aid tab.
Click Repair Disk.
If Disk Utility can’t repair your disk, back up as much of your information as possible, and then follow the instructions in “Erase and reinstall OS X Yosemite"
Erase and reinstall OS X Yosemite
If you erase and reinstall OS X Yosemite, everything (your user accounts, network settings, and all of your files and folders) is deleted. Before you erase OS X, back up any files you want to keep by copying them to another disk. Write down your network settings from Network preferences to make it easier to get connected again after reinstalling Yosemite.
NOTE:You may want to write down these instructions before going forward.
To start your computer from Recovery, restart your Mac and hold down the Command and R keys at startup.
Select Disk Utility, and then click Continue.
Select your disk from the list on the left, and then click the Erase tab.
Choose Mac OS Extended (Journaled) from the Format pop-up menu, enter a name for your disk, and then click Erase.
After the disk has been erased, choose Disk Utility > Quit Disk Utility. Select Reinstall OS X, click Continue, and then follow the instructions in the OS X Installer to reinstall Yosemite.

Database Recovery using Archive files

Dears,
Due to some issue our database get crashed.
We have saturday night offline backup and archive backup till yesterday night.
We have restored offline backup and system is Up but it is on saturday night state.
We want to apply these archive files to make the system state to current.
In restore our control file also get replace with our saturday night control file status.
We have copied our archive files in oraarch directory.
Now when using brtools I am applying archive files:
Command executing in brtools:
recover from '/oracle/<SID>/oraarch' database
it shows
unknow command beginning
No recovery required
On sqlplus also when I execute
sql>recover database;
It shows no recovery required.
When I give command:
sql>recover database using backup control file;
it ask for some {file name| AUTO | CANCEL}
I give first file name of oraarch it shows "Can not access the file".
File permissions are ok.
I give AUTO, It also then do not do anything.
Please suggest the correct method to make my system in latest current date.
Shivam

Hi Shivam,
This is absolutely normal that during the restore your control files will be replaced by the old one which were backed up during database backup.
Logic is that you can not apply the redolgs which are having the timestamps older than your restored datafile's / controlfile's timestamp.
If your DB is not yet opened, you can check the status of your database using below command which will tell you, till what timestamp your data is restored or currently available.
select to_char(CHECKPOINT_TIME,'yyyy-mm-dd:hh24:mi:ss') from v$datafile where file#=1;
>
> From command I want to know "from backup control file"....Do SAP take backup of control file as in system only old is
>
> available.
> Shivam
>
recover database using backup controlfile..... this command does not backup the controlfile . this will make use of old controlfile only which came along with the restore and start the recovery using this controlfile only.
Its just make use of available controlfile ..No backup will be triggered.
Please make a note that after DB restore; ..recovery is possible only in case database is not yet opened in OPEN state.
Cheers !!!
Ashish

Itouch has frozen mid-update and will not shut off or restart

My 5th generation iTouch has recently begun downloading the newest iOS update. The update did not complete (thus a restart has yet to occur); however, I am unable to even power off the device (held the power button in excess of one minute without it shutting off the device). I just downloaded the ITunes 12 update, but have some tasks to complete before restarting my computer (to allow for a possible recovery restart). Also, when plugging in the iTouch to the computer, the device isn't recognized or accessible.
How can I restart the device without using a recovery option?
Thank you in advance for your much appreciated attention and support provided by the community.

- Try letting the battery fully drain and then charge and try a reset
Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Next try connecting to iTunes and try making a backup.
- Last restore the iPod using Recovery mode if necessary.

Brtools recovery - restart possible?

Similar Messages

Maybe you are looking for