BT Diverse 4016

Hi,
Please does anyone know how to un-delete an answerphone message on a BT Diverse 4016 as I’ve just managed to accidentally delete a message that has massive sentimental value to the family. Huge thanks to anyone with an answer...

The chances are that once it has been deleted that it has been now totally lost, not the news you want to hear i am afraid.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

Similar Messages

BT Diverse 4010 - handset icons flashing

I have a BT Diverse 4010 - the handset icons just keep flashing. I have tried replacing the battery and tried to use code 0000 to try to register it with the base again. I have also tried turning the base on with the button underneath (to register with base) pressed to reset it as suggested on some forums but these dont work. I am not sure if there is a way to reset the handset and then try and register with the base again. Any ideas would be appreciated.
Thanks in advance.

From the manual
No radio signal to the base – all
displays flashing.
Means
Handset out of range.
Handset not registered.
Base not switched on
Try
Move closer to the base.
Register the handset (see page 11).
Check the base is connected
properly (see page 10)
To de-register a handset
Press the INT options button.
Press the UP or DOWN button
to select the handset to be
de-registered (1-6).
Press the MENU options button.
Press the DOWN button until
the display shows DE-REG H/SET.
Press the OK button. Display
will show PIN ****.
Enter your 4-digit PIN
(original setting 0000).
Press the OK button. Display
shows DE-REGISTER?
Press the OK button to confirm
To register handset
On the handset to be registered:
Press the MENU options button.
Press the DOWN button until
the display shows REGISTER HS.
Press the OK button. Display
show PIN ****.
Enter your 4-digit Pin (original
setting 0000).
Press the OK button. Display
flashes REGISTER HS.
If the base station is a Diverse
4010 or 4016 base press the
PAGE button located
underneath the base station
for approximately one second.
After approximately one
minute the handset will display
its internal number. The
handset is now registered and
the handset display will return
to the idle screen.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

How do I get Adobe Reader to stop trying to open the game Diversion and find a better "opener"?

I downloaded the game Diversion at least 4 times but I couldn't find it. When I finally did, it turned out that Adobe Reader was trying to open it. How do I fix this with the right "tool" for the job?

What is your operating system?
What is "game Diversion"?

Br350 - Diversity and drivers issue

Hi
I have a problem with the Aironet BR350, in the way it handles diversity. I run V12.05, and I use them as bridges with clients which means other bridges can route through.
I have Tx/Rx diversity enabled on both rightand left antennae, and I log the signal strength every second via SNMP. It is my perception that the radios will keep the connection down to 30-35% signal strength.
However, some times when the Rx signal strength on a non-root unit is averaging around 60-70, a singular drop to 35-40
(or even higher like 45)
would coincide with the root unit to restart the process to the non-root-bridge, which causes a dropout of about 30 seconds. Reason for the drop of signal strenght is believed to be a short temporary multipath fade much less than 1 second, and in some of these cases the signal quality also gets worse. But I only get one outlier hit in the log. It is too bad that this causes 30s outage.
At this time I know for sure that the other antenna has a reasonable signal.
Has anyone got any similar experience, and maybe a solution?

Hi
here is a transcript of debugging. Note that these are logged on the RootBridges network, and timestamp is when they arrive there after the link is restored.
Mar 16 06:20:36 [ip address omitted] NonRootWirelessBridge(Info): Associated to Parent
[Bridge_Root]00409656db77
Mar 16 06:20:40 [ip address omitted] NonRootWirelessBridge (Warning): Lost Authentication
with Parent
Mar 16 06:20:40 [ip address omitted] NonRootWirelessBridge (Info): Stopped driver for port
"br9"
Mar 16 06:20:41 [ip address omitted] NonRootWirelessBridge (Info): Started driver for port
"br9"
Mar 16 06:20:41 [ip address omitted] NonRootWirelessBridge (Info): Associated to Parent
[Bridge_Root]00409656db77
Mar 16 06:20:41 [ip address omitted] last message repeated 1 time
Mar 16 06:21:19 [ip address omitted] NonRootWirelessBridge (Warning): Lost Authentication
with Parent
Mar 16 06:21:19 [ip address omitted] NonRootWirelessBridge (Info): Stopped driver for port
"br9"
Mar 16 06:21:21 [ip address omitted] NonRootWirelessBridge (Warning): Failed to Send
Packet on port "awc0" (error=0x00000041)
Mar 16 06:21:21 [ip address omitted] last message repeated 9 times

I am conducting a report on diversity for a research paper. Who do I contact or interact with via chatroom?

I am contacting a diversity audit research paper. Who can assist me?

https://www.google.com/search?q=gay+diversity
https://www.google.com/search?q=nationality+diversity
https://www.google.com/search?q=religious+diverity
https://www.google.com/search?q=ethnic+diverity
I hope your paper is more precise than your question.

Diversity and trying to conver two different areas

So the whole purpose of diversity is to provide/improve coverage in a same area. Basically two antennas placed with a reasonable distance from each other and the concept is that one antenna might receive a better signal than other and then both signals can be combined to get a single stream. End result better communication.
Now something I have noticed that people are doing is taking the two antennas and putting them like 25 to 50 feet apart with diversity enabled trying to cover two different areas. At times two different rooms so like one antenna is in one room and second one is in another room with a concrete wall between them. Apparently they are saying that it is working for them. I'm trying to understand the logic behind that how something like that wouldn't cause issues unless they have clients only on one side?

I've seen set-ups like this before and people at the site can (and will) say that it's "working".
Until I get a wireless sniffer out or do some scanning, it seldom works. They will say that it's working purely for political (don't want to get themselves into trouble) and/or financial (they can't afford to put two APs) or both.
This may work (somewhat) in 802.11a/b/g but stick 802.11n/ac and I'm certain it won't work. When I mean it won't work, I mean you won't see the full benefit of connection speeds of >155 Mbps.

Quicksilver 2002/ Elegato eyeTV diversity

Will a dual 1Ghz Quicksilver 2002 with 1Gb SDRAM,80Gb HD,running OSX 10.4 be able to use the Elegato EyeTV diversity 2008? It does have a PCI hispeed USB card (I assume therefore USB 2.0?) but I do get error messages about a USB hub drawing too much power & being de-activated. (I think this possibly is due to the PCI card having a VIA chipset.) Any thoughts would be appreciated

I know nothing about eyeTV but if the message is too much power is being requested then I'd suggest trying the device with a powered hub if there isn't the option to power it directly.

Iphone4 external mic problems - Ultradisk 4016 Lavaliere Mic

Hello Everybody
Maybe someone here can help as its after hours at Ultradisk and therefore I can´t ask them.
I purchased two Ultradisk 4016 Lavaliere Mics to record Audio with an iPad Mini and my trusty old iPhone4.
Bought RodeRec too, the pro version. I have set up everything. With the iPad the Lavaliere Mics work like
charm.Really good quality. RodeRec works just fine with the Ultradisk mics.
On the iPhone4, no can do. Running iOS7 with the corresponding version of RodeRec.
Line in / Input is like listening to a hoarse man in a tiny box. I tested the mics with the iPad, they both work
just fine. Out of curiosity I tried my apple headset and I got nice and crisp recording alas with a lot of
scratching as the mic is moving on the fabric of the shirt. I checked that the Lavaliere Mics plug in all the
way, they do. The problem exists in other recording apps too. I hope there´s an easy explanation or fix for it.
Any help, tips and tricks would be appreciated.
And please, don´t state the obvious like "buy a new phone" or "why don´t you just use your headset then".
I will use the headset this weekend as a last resort, but if the mics work on one device, and one kind of mic works
on both, I do not understand why the Lavaliere Mics will not, especially when they work fine on another iOS device.
Here are the specs of the Ultradisk 4016, it is made for mobile "smart" devices:
A good quality metal crocodile style clip, secures the mic in place.
1 Metre cable 3.5mm TRRRS
Polar pattern: omnidirectional
Mic diameter: Î¦6.5*5.0 mm
Sensitivity:-47dB±2dB
Frequency Range: 20-20KHz
Output Impedance: =680 SNR: >58dB
Standard Operation Voltage: 2.0V-10V.DC
Thank you very much in advance for your help.

There is a box in the top right corner of this discussion group labeled "Search Discussions". Just type HV20 in there. There have been a couple of threads lately on the HV20.

Aironet 1300 antenna diversity query

good day!
does anyone had already configured an antenna diversity for aironet 1300 with 2.4Ghz frequency?
we want to have a ring type network, we have a site A that needs to have a stable link and this site A has an line of sight to two active sites, this are site B and site C. site B is a root bridge and has a different frequency and SSID and site C is a non root and also has a different frequency and SSID, do i need to re configure the two sites (B & C) to have a uniform transmit frequency and SSID so that we can have an antenna diversity in site A? so that, in case the link between site A and site B will have a problem the data will be re routed to the site A and site C link. Can anyone give us some tips to make the antenna diversity works.
hoping for some replies. thanks!
wel

maybe you are confusing diversity with redundancy??
If this is a point to multi-point setup and A is central to both B and C, then A should be the root bridge. B and C should be non root and have the same SSID as A. The channels are determined by the root bridge(A).
If the link between A and B goes down, C and A will continue to work only if A still works. B will still be down. If A goes down, both B and C are dead.
You will need to do multiple bridge shots with two root bridges as in A to B and A to C and possibly B to C with a bunch of spanning tree in there somewhere.
You should research this further; at this point the shot itself isn't the hard part, it's getting the fail-over to work correctly.

More about diversity

About two years ago you clarify my doubts about diversity, but today after seeing a hyperlink patch antenna data sheet, a doubt came to my mind, what if both antennas are identical and cover the same cell but with a little difference, the polarization, the antennas are cross-polarized , which happens in this case?
Thanks

The antenna that is not in the right polarization will be about 3dB down.
Since it get a weaker signal, it will be selected less often.
In a case where you have PC antennas (tend to be vertical polarization) and laptop NICs with built in antennas (like the Cisco, which tends to be horizontal polarization), perhaps some benefit could be gained, I can't say I've ever measured or monitored it in that config.
Good Luck
Scott

Mapping SIP Diversion Header into SIP To: field

Does anyone know how to use SIP Profiles on a CUBE to map the SIP Diversion Header into the SIP To: field?

It looks like, according to the below note from the "Additional Configuration Notes" section in that doc, that this is not possible on the CUBE:
"Regular expression variables can be used to extract and store parameters from an existing header, but the values stored in variables in one rule can be used ONLY in the replace-pattern of the same rule; it can NOT be used by any other rules, which means you cannot insert the values extracted by one rule into another rule. " (third bullet in http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_example09186a0080982499.shtml#notes)
Sounds like I can extract the number in the Diversion header in one rule but I cannot then use it to modify the To header in another rule.
Can anyone confirm this?

Printing problem in SD-DIVERSION ORDER

Hi all,
I wanted to print a diversion order rather than a CREDIT MEMO ,although the document says "credit Note" on it.I want the printing as diversion order.
Regards,
kishorekumar.J

No answer

No wlan and error 4016

Hi,
after upgrading my iPhone 4s to iOS 7 I am not able to use my wlan-function anymore.
(I restored the phone several times via iTunes and resetted the function on my iPhone too, nothing changed)
During another try my iTunes gives back error 4016 (seems to be a very mysterious error, as it is not even listed in the error-list of the apple-support-side and nobody seems to have an answer).
Some further informations: I am not using windows, but have a mac, my iTunes is on it latest update, so is my iPhone.
And I am not able to update via wlan/wifi because this function does not work since my very first upgrade on iOS 7.
Any help?
(before my iPhone meets my wall....)

I have the same problem. Very sad that there is no response on this.

Unable to update ios7.1 in iphone 4S.Its throwing me 4016 error

I am trying to update my ios to 7.1 from one weeek its throwing me 4016 error all the time. I am trying this using itunes and I verified I have latest itunes in my laptop.

Hello there, Hima bindu tenneti.
The following Knowledge Base article offers up some great steps for troubleshooting your issue:
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694
In your case the error message you have is found in this information:
Check USB connections
Related errors: 13, 14, 1600-1629, 1643-1650, 2000-2009, 4000, 4005, 4013, 4014, 4016, “invalid response,” and being prompted to restore again after a restore completes.
If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
To narrow down the issue, you can also change up your hardware:
Use another USB cable.
Plug your cable into a different USB port on your computer.
Try a different dock connector (or no dock).
Add (or remove) a USB hub between your device and computer.
Connect your computer directly to your Internet source, with no routers, hubs, or switches.
If you checked your connections and are still seeing the error message, check for hardware issues.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

BT Infinity and DECT Phone BT Diverse 6350

I have just had BT infinity installed at home with the latest Home Hub (V3).
I am using a BT Diverse 6530 digital corded /cordless phone for my voice calls. Due to the location of my study the engineer wired the telephone directly to the master socket which also hosts the broadband connection to the router and then straight out of the home to the external telephone line.
The problem appears to be on incoming calls . When answered on the corded phone on the base station the reception is fine. However when an incoming call is received on the cordless handset downstairs in another part of the house the calling person cannot hear any speech (although I can hear the other person clearly).
This problem has only surface since I have had the new infinity installed last week . I suspect it is something to do with the channel frequency separation on the BT Home Hub Wi-Fi and the DECT system the BT phone is operating in.
Any suggestions to resolve this problem would be most welcome
Many Thanks

If you have not already tried it move the base station and the router a few feet apart - both can interfere with each other but a few feet of air can help a lot!

BT Diverse 4016

Similar Messages

Maybe you are looking for