BT Home Hub and Airport Express

Although the BT Home Hub is 'Mac' compatible, there is still little information on using it with Airport networks. I hope that the following makes sense (I am no expert) and is useful?
Connect the Airport Express via Ethernet cable to the Ethernet 1 port of the Home Hub
Open Airport Admin Utility
Airport Tab>Base Station>enter a base station name
Airport Tab>Airport Network>Wireless Mode>Create a Wireles Network(Home Router)
Airport Tab>Airport Network>Name>enter a network name
Airport Tab>Airport Network>Wireless Security>enter your preferred security level and ensure it matches the Home Hub security level
Airport Tab>Airport Network>Channel>choose the same channel as your hub, do not use automatic
Airport Tab>Airport Network>Create a closed network>leave this unchecked
Airport Tab>Airport Network>Mode>if you have a mix of 11b and 11g cards leave the mode at 892.11b/g Compatible
Airport Tab>Airport Network>Wireless Options>leave these alone if you want to avoid problems
Internet Tab>Connect Using>Airport (WDS)
Internet Tab>Configure WDS Host>MAC Address>enter the MAC address of the Home Hub(i.e the primary WDS base station
Internet Tab>Configure WDS Host>MAC Address>tick the box Also allow wireless client computers
Internet Tab>Configure WDS Host>Configure>Using DHCP>the IP address will be assigned in the range 192.168.1.6*and the Subnet mask should read 255.255.255.0 and Router address should be 192.168.1.254
Network Tab>Uncheck Distribute IP addresses
WDS Tab>Enable this base station as a WDS>check this box>from the drop down list choose>remote base station
WDS Tab>Allow wireless clients on this base station>check this box
WDS Tab>Main AirPort ID> enter the MAC address of the Home Hub or use Select to scan for the Home Hub wireless network and you should pick up the MAC address etc automatically
Click to Update these settings.
Go to bthomehub.home and ensure that you have WDS dis-ABLED in the settings. You will have to log on as admin (password is defaulted to ‘admin’, but it is worth changing it!).
To do this after logging on as admin go to>Home Network>Interfaces>WLAN At this point you should be presented with Wireless Access Point click on Configure (top right) Scroll down the screen that follows and click Configure WDS and you will be presented with the Wireless screen. Click Scan for wireless access points. The BT Home hub will scan for available networks and once it has found these you should click apply but DO NOT ENABLE WDS! Click back from this screen to Home Network and you should see your wireless Mac(s) and their various connections
Best wishes and hope this works for you! My iMac/Mac Mini and PowerMac G4 now connect perfectly through the Airport Express and I have extra Extreme and Dual Ethernet Airports for printer and Windows file sharing. I am running OS X 10.4;10.3 and 10.2 variously without seeming conflict. Airport firmware is 6.3
Power PC 400 G4 AGP 10.2.8 Mac OS X (10.4) iMac G4 800 10.2.8; Mac Mini 1.42 10.3.6;Airport Dual Ethernet BS
Power PC 400 G4 AGP 10.2.8 Mac OS X (10.4) iMac G4 800 10.2.8; Mac Mini 1.42 10.3.6;Airport Dual Ethernet
Power PC 400 G4 AGP 10.2.8 Mac OS X (10.4) iMac G4 800 10.2.8; Mac Mini 1.42 10.3.6;Airport Dual Ethernet BS
Power PC 400 G4 AGP 10.2.8 Mac OS X (10.4) iMac G4 800 10.2.8; Mac Mini 1.42 10.3.6;Airport Dual Ethernet BS

I have now changed settings as you advised from WDS to Ethernet for the Express>BT Home Hub connection.
I know from previous posting that the ABS Snow does not support WDS.
Hers is what I want to achieve, however so far, with the exception of the Mac Mini (untested/unconfigured for use with Extreme)it all works?:-
Power PC 400 AGP OS 10.2.8>Airport Extreme PCI Card>Wirelessly connect via Express(connected via Ethernet to BT Home Hub)
Mac Mini 1.4 OS 10.3.6>Ethernet>ABS Extreme>Wirelessly connect via Express (connected via Ethernet to BT Home Hub)
iMac G4 Flat panel OS 10.4>Airport Original Card>Wirelessly connect via Express (connected via Ethernet to BT Home Hub)
Samsung PC Windows XP(SP2)>802.11G Card>Wirelessly connect via Express (connected via Ethernet to BT Home Hub)
All four of the above connect to the ABS Snow on a separate wireless network for file sharing and printing.(I set this up via help/info from the discussion forum and given it works without hiccup have left it as it is!)
Hope this helps and any further assistance/advice is appreciated-I am keen to get it right since the BT Home Hub is relatively new-UK based Home Hub forums http://www.digitalspy.co.uk/forums/forumdisplay.php?f=77
Thanks,
Graham
Power PC 400 G4 AGP Mac OS X (10.2.x) iMac G4 800 10.4; Mac Mini 1.42 10.3.6;Airport Snow;Airport Express;

Similar Messages

BT Home Hub and Airport Express Issues

Hello all
I am having major issues setting up my airport express to my home hub and also setting up Time Capsule to join my wireless network...
I really need a step by step guide if possible.
Can anyone help please?
Thanks
PC

Welcome to the discussions!
You told us that you were having "major issues", but did not tell us specifically how you are trying to configure the AirPort Express, or what service you want it to perfrom on your Home Hub network, so providing a step by step guide is not possible without a bit more information.
Can you clarify on this, please?
In regards to configuring your Time Capsule to "join" the Home Hub wireless network, do you understand that the ethernet ports on the Time Capsule are not enabled in this type of configuration, so you will not have the option to back up large files or make initial backups using an ethernet connection?
In order for the Time Capsule to "join" the wireless network provided by the Home Hub router, you willl need to know (or be able to locate) the exact type of wireless security settings that your Home Hub is using. The Time Capsule must be provided with this information in order for it to "join" the wireless network successfully.
Can you provide this information, or if you do not know, check with your service provider to obtain this information? We cannot proceed with the configuration until we have this information.
If you are able to locate the Time Capule near your Home Hub and establish a permanent ethernet connection between the Home Hub and Time Capsule, you will be able to backup using the Home Hub wireless network and also have the option to backup using ethernet if you wish. In addition, this type of installation is much simpler to configure (and more reliable in operation in my experience) and we would not need to know the type of wireless security that the Home Hub uses if you choose this setup option.
Please post back when you have an opportunity.

2wire home portal and airport express ?

I have a 2Wire home portal 1000hw modem and need some information on how to connect it with my airport express. My 2wire modem is either wireless or ethernet. I would like to connect my modem via ethernet to my airport express and use the airport express to connect to the internet.
If you have any ideas or suggestions or could direct me to somewhere I would greatly appreciate it.
Ryan

To change the Channel your 2Wire Gateway broadcasts it's wireless on, follow these steps
Type one of the following addresses in a browse:
http://home
http://homeportal
http://gateway.2wire.net
http://192.168.1.254
- Click on homenetwork
- Click on Wireless settings
- enter password if prompted
- where it says wireless channel, change it in the drop down menu.
- click save or submit
Mac OS X (10.3.9) G4 AGP Graphics & G3 ibook 800

Airport Express with BT Home Hub and Xbox 360

Hi,
I know this is kind of an out there question, but im looking into buying an airport express and i was wondering if there was a way that the Airport express could connect to my existing wireless network (BT Home Hub) and share that internet connection over ethernet to my xbox 360.
My xbox is in another room and i cannot connect it to the router. I have been reading about WDS and client mode but it all goes over my head. can anyone explain if this is possible with the airport express even though i dont have an apple base station?
Im also wondering if Airtunes would work for my speaker system. Any help is appreciated!

Welcome to the discussions!
"i was wondering if there was a way that the Airport express could connect to my existing wireless network (BT Home Hub) and share that internet connection over ethernet to my xbox 360."
Possibly. You would need to check to see if the BT Home Hub was compatible with what is called ProxySTA. Otherwise, the ethernet port on the Express will not function.
WDS would not be compatible with your BT. Even if it were, the wireless network bandwidth would be reduced by 50%. Not what you want for gaming.
Assuming your BT is a router with ethernet ports, you absolute best connection for any application, but especially gaming is an ethernet cable.
If this is not feasible, look at ethernet power line adapters. One adapter plugs into the AC socket at the router end and the other plugs into an AC socket near the 360. The adapters use the AC wiring in your home to transport the ethernet signal. This is almost as good as a straight ethernet cable and far better than wireless for gaming.
The Express would be able to join the wireless network of the BT router for use with AirTunes.

I have recently changed my bt home hub and now my airport express won't connect to it? Any suggestions?

I have recently changed my bt home hub and now my airport express won't connect to it? Any suggestions?

Anytime you change out a modem or modem router like the HomeHub, the AirPort Express needs to be reset back to factory default settings and then set up again.
The reason for this is that the Express is retaining some or all of the settings to connect to your "old" modem or hub, so it will not work correctly with a new device unless you start over again from factory default settings on the Express.
Power up the Express for a few minutes
Hold in the reset button on the side of the Exprsss for 8-10 seconds, then release and allow a full minute for the Express to restart to a slow, blinking amber light
Now, set up the Express again, like you did originally with the "old" modem or hub that you had previously.

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

If i have a home full of Apple TV's and Airport Express' can i airplay music in every room at the same time?

If i have a home full of Apple TV's and Airport Express' can i airplay music in every room at the same time?
Or just one device(room) at a time?
It seems there is a lot of home theater systems where they all hook up to one "control" and then disperse to the different locations per instructions..
Is this possible with all apple products?

From iTunes using Multiple Speakers (you can control with the Remote app on iPhone/iPad too), but not from AppleTV itself.

Bt Infinity, HH3 and Airport Express

am thinnking about taking BT infinity. THis apparently needs HH3. Have seen threads about connection problems between HH3 and airport express. (I had similar problems with HH2, so resorted to old BT Voyager)
1. does anyone know if problems with HH3 and airport express can be fixed
2. Can I use BT infinity with a BT Voyager
thanks

Re: "If you get Infinity you will not need the HH3 in the first place you can just connect the Airport Express to the Openreach modem."
No use at all. I don't know what you use your Airport Express for, but mine is used to send music to our hi-fi, and so has to be connected to the hi-fi. Therefore it cannot also be connected to the modem.
This worked fine when I used to get my internet via (whisper quietly) Virgin. But with BT Infinity it would lose its connection every now and then. Apple provided a free replacement but that was no better. Following a few tips (e.g. connect to one's laptop via ethernet cable for setup) I was able to set up a connection eventually, but it still loses connection quite frequently. Interestingly enough, resetting the hub gets it going again, though restarting AE does not!

How to setup ADSL moden router and Airport Express 802.11n (1st Generation) to provide internet and airplay connections to multiple devices?

I have a Netgear wireless ADSL modem router (wireless + four ethernet out ports) that i'd like to connect to a 1st gen Airport Express to create a small home network to provide internet access for a MacBook, iPhone and Apple TV, and to provide Airplay connection to the Apple TV and Airport Express audio output jack.
I'd like to turn off the wireless function of the ADSL modem router, and to have from one of its ethernet out ports an ethernet cable providing internet directly connected to my MacBooks ethernet port.
Then from one of the other ethernet outs on the ADSL modem router an ethernet cable connected to the Airport Express's ethernet port. This would be to provide wireless internet connection for the Apple TV and iPhone via WiFi from the AE.
At the same time as the MacBook is receviing internet soley via the ethernet in port, i'd like it to have WiFi connection to the AE to provide Airplay connection to the Apple TV and the AE's audio out jack.
Is this all possible? How should I go about to configure this? How should the AE's ethernet port be configured?
Any special modes the ADSL modem router or Airport Express should be in? ie bridge or client?
Thanks

On the ADSL modem router web-based interface, should I set any security setting? I think not as there'll be no wireless signal coming from it, only wired ethernet connections to both MacBook and AE. Security should only be set on the AE to prevent someone from accessing its WiFi signal. Is this assumption correct?
These are all correct!
How should I go about setting up security for this network?
First I would recommend that you configure the AirPort Express for WPA2 Personal. This will provide you with the greastest level of security while still providing excellent bandwidth performance.
You would configure wireless security for the Express by using the AirPort Utility on a Mac, PC, or iOS device. Using your MacBook Pro as an example, you would do so as follows:
Run the AirPort Utility.
Select the Express, and then, click on Edit.
Select the Wireless tab to enable it.
Set the Wireless Security option to: WPA2 Personal
Enter the desired password in both the Wireless Password & Verify Password fields. Note: Use of a "strong" password is encourage here. By strong, I mean use a mix of upper/lowercase letters, numbers, & punctuation marks. Try not to use common dictionary words. If you operate your wireless in an area where security is of an utmost concern, I would further suggest that you change the wireless security password every 60-90 days. Also don't forget to change the default AirPort Base Station Administrator password as well.
Click on Update and allow the Express to restart.

Is there a limit to the number of airport extremes and airport expresses one should have in a network?

Is there a practical limit to the number of airport extreme base stations and airport express units one should have in a home network?

Then, I had an older Airport extreme that I was thinking about connecting wirelessly in my living room and connecting the DirectV DVR to it by ethernet cable.
Is this older AirPort Extreme the "round" version or the "square" shaped version? The "round" version will not do what you want.
Whenever you extend an AirPort using wireless only, you will experience a loss of bandwidth (speed) on the entire network. That loss might be anywhere from 15-50% depending on how far the extending AirPort device is located from the "main" AirPort.
Even with an excellent signal, if you have 3 AirPorts extending the signal, you will lose 40-50% of the bandwidth on the network. The other AirPorts that are being used just for music are also slowing things down.
He thought there might be problems with using that third airport with the DVR and wondered if I should just use an Airport express there.
It would make no difference whether you used an AirPort Extreme....assuming it was the "square" version or a new AirPort Express as far as performance is concerned.
As to whether you connect the DVR to another AirPort, it might be OK, but you will not know until you try.
If you find that things slow down noticeably, you will need to look for ways to connect the AirPorts together using a wired Ethernet connection. This is always the preferred connection method since there is no bandwidth loss when you do this.
Since downloading video places a high demand on a wireless network, you might want to look for a way to connect the DVR back to your "main" router directly using a wired Ethernet connection as well.

I used part of my name in my home network. Now I understand this was stupid security error. How can i change the name of my home wifi network, airport express? Thanks.

I used part of my name in my home network. Now I understand this was stupid security error. How can i change the name of my home wifi network, airport express? Thanks.

Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the picture of the AirPort Express
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Edit the Wireless Network Name
Keep it short.....maximum 10-12 characters or so. No blank spaces or punctuation marks in the name
Click Update at the lower right of the window to save the new setting and wait a full minute for the AirPort to restart

IPod Touch and Airport Express

I have a home network with Airport Express access point connected to my Bose entertainment system which allows me to play my iTunes music on the Bose speakers. With iPod Touch and it's WiFi capabilities, can I play my music on the Bose speakers as well?

There is no evidence to suggest AirTunes is available on the iTouch / iPhone
Sorry!

Wireless connectivity issue between MacBook Pro/ iTouch and Airport Express

I'm creating a wireless network at home using my airport express and depending on the configuration settings I set in the airport utility, I will face the following issues:
1- To connect my MacBook Pro to the wireless network created, I have to set the radio mode to 802.11n only (5 GHz). Any other radio mode (a/b/g compatible or n only (2.4 GHz)) will not work ("Couldn't find the network")
2- Conversely, the use of the radio mode 802.11n only (5 GHz) with my iTouch doesn't work ("Couldn't find the network"). To connect my iTouch to the wireless network created, I have to set the radio mode to 802.11a/b/g compatible or to n only (2.4 GHz)
As a result, I manage to 1) either connect to a wireless network created with my airport express with my MacBook Pro only 2) or with my iTouch only, depending on the configuration setup.
I'm using the latest updates for the airport utility (7.4.2), iTouch (3.1.3) and Mac OSX (10.6.4).
Any help on this?

if you set it to the most compatible with the least common denominator you should be able to connect with both. (If that's what I understand you are trying to achieve).

Connecting to existing home network via Airport Express

I had my Macbook Pro connected to our home router which allowed me access to our home network and the internet. On this network we had connected both my MBP and my flatmates PC (which is connected directly to the router via network cable).
Through this configuration i was able to both access the internet AND access files on the PC. I have recently purchased and airport express to eliminate the need for the network cord. Since setting up the AE i have been able to connect to the internet no problem by creating a wireless network and using all the automatic settings, however in the process i have lost my ability to connect to the home network and my flatmates computer. In fact, under "networks" in finder the home network has disappeared. Also in network prefences i am getting a warning saying "The cable for Ethernet is not plugged in".
Is anyone able to tell me what im doing wrong?
thanks ....
Message was edited by: seysearles

The problem is that the AirPort Express (AX) is creating a subnet.
To prevent that, configure the AX to act as a bridge (so that it is NOT sharing a single IP address).

Question about Time Capsule and Airport Express co-existence

I have a new 3TB ME182LL/A Time Capsule attached to my wired home LAN, in bridge mode. It works fine both as an access point on the upper floors of my home and as a Time Machine device. I also have an Airport Express, whose function in my network is solely to control my whole-house audio system from ITunes. I don't need, want, or use the wireless networking features of the Airport Express. I just have an audio cable running from it to my stereo, and an Ethernet patch cable connects it to my wired LAN. The network mode in the Airport Express is set to "off". Historically, the Airport Express has worked fine in this wired lan mode. However, I unplugged it at some point while having some initial trouble deploying the new Time Capsule and only turned it back on today. After turning it back on I observed something strange. My speedy wireless connection upstairs via the Time Capsule became slow. And when I launched Airport Utility, it drew a network diagram which showed my Time Capsule as a CLIENT of the Airport Express. In other words, the network diagram showed Internet at the top, then a vertical line down the the Airport Express, then the Time Capsule below that. The correct / desired diagram would be the Time Capsule and Airport express as peers. I connected to the Airport Express and verified that network mode was set to "off" but the incorrect network diagram persisted (as did poor wireless performance) until I unplugged the Airport Express. After I did that, the Airport Utility drew the network correctly, although of course it showed a yellow caution sign next to the Airport Express, since it was down. And my wireless speed / reliability returned to normal. What is going on here?

The automatic setup in the airport utility has changed something.
Is the line down to the TC from the express dotted.. in other words is wireless??
Funny stuff happens.
Please post the screenshots of the 3 pages from the airport utility setup for both airport express and TC..
Make sure wireless is set to off in the express.
Both should be set to dhcp on the internet tab and both set to off bridge mode on the network tab.
So for example the bridge on the network tab.
The summary page can also be a help.
There is a half summary page when you click the item in the airport utility.
There is also a fully summary page, when you hold option key and double click the TC icon for example.

BT Home Hub and Airport Express

Similar Messages

Maybe you are looking for