BT Home hub not connected message

We use my wife's XP sp3 laptop wirelessly at home, but when we use it away from home on a 'paid for' wireless providers network (as no BTFon is avaliable at that location), we occasionally get the BT Home hub not connected message come up in an IE page. How can it be turned off, there is no solution in BT FAQs?
Regards
Solved!
Go to Solution.

Just for good measure, I would install another web browser while you still have internet access. Then if you have the same problem, try the other web browser and see if that works.
I noticed that you said it says that the Hub is switched off. This is the message that appears when there is no internet connection at all.
Maybe the WiFi had dropped and there was no signal for a small period of time, then when it went to go to the 'page cannot be displayed' screen it redirected you to the 'hub is switched off' message because it had been cached previously.

Similar Messages

TS1567 Suddenly my I phone 4 will not connect message mobile device service could not be started (nothing has changed on my PC). I have tried following the troubleshooting and have restarted the mobile device) but it still won't connect. Also all my disap

Suddenly my I phone 4 will not connect message mobile device service could not be started (nothing has changed on my PC). I have tried following the troubleshooting and have restarted the mobile device) but it still won't connect. Also all bookmarks have disappeared!

Okay ... it's a better bet with a 1067 error message when trying to start the Apple Mobile Device Service, but we'd better check for a LSP issue, as per the following document:
Apple software on Windows: May see performance issues and blank iTunes Store

Wi fi not connected message

My ipad 2 wi fi is not working, I get a Not Connected message. Has anyone had this problem? if so what is the solution to be able to reconnect.
Thanks

Bghawes-
I suggest you unplug your WiFi router for a few seconds. Then reset the iPad's network. Go to Settings-General-Reset-Reset Network Settings. You will then need to re-connect the iPad to WiFi.
Fred

IPad lost home hub wireless connection

Our iPad has stopped connecting wirelessly to our Home Hub 3 whereas it worked perfectly before and an iPhone still connects OK. We've tried the Helpdesk advice of isolating BTWiFi and BTWiFi-with-FON by using "Forget This Network" but it still brings up the message "Unable to join the network BTHub3" etc. Any ideas?
Solved!
Go to Solution.

Carry out a factory reset of the Homehub by pressing a pin into the red recess on the hub for about 20secs. When connecting the iPad use the PASSKEY found on the homehub or the pull out card that came with the hub. Do not use your email password or any other passsword.
See this link for how to connect:
http://bt.custhelp.com/app/answers/detail/a_id/35889/~/how-do-i-connect-an-ipad-to-my-bt-home-hub%3F

Home Hub Ethernet Connections

Have had the BT home hub 1 for years with 3 PCs connected via Ethernet & USB connections (wireless is useless as house is 170 yrs old with 15 inch thick walls that have defeated all wireless attempts). Now that I have vision there are not enough connections. An alternate provider is offering a similar speed unlimited service with a 4 Ethernet port hub and although it is far cheaper I've always had reasonable service from BT and don't really want to change (Mug?). Is there any way that a further connection can be made from the current hub or does this spell the end to an account I've had for many years?

Have tried the ethernet thru the mains and it is too slow! I have Cat6 ethernet from all four ports on the BT Hub Mk2 and each one terminates at NetGear Gigaswitches providing 4 further ethernet ports on each. Yes that is 16 ports! They are all in use and I find that shifting large Jpegs and large video files around are no problem. As well as the PC's, Printers, NAS drives etc., there is the BT Vision (Freeview), Humax PVR (Freesat), Blu-ray and Freesat TV to contend with. NetGear Gigaswitches (GS605) are very cheap from Amazon at the moment and do not require any setup whatsoever.... having struggled to get Ethernet over the mains and wireless thru floor and walls, I know which 100% dependable route I prefer
OLD MAN ( Three Score + Ten and still going)

Home Hub 3 - Connection dropping from N to G?

Hello all; I hope someone can help me with this!
I have recently installed the new Home Hub 3 (replacing a Home hub 1). I have it connected by wifi to a Mac which has a built-in 802.11 connection. The reason I changed to Home Hub 3 is that next month I am getting a digital box for the TV which works best using a 802.11 N connection speed.
Normally, the connection is by 802.11 N (I can see this on the Mac SysInfo), and I get a solid 5 bar connection. However, sometimes this drops to 1 or 2 bars, and the wifi speed drops from N to G. When this happens, I cannot change it back to a N speed without rebooting.
Does anyone know what might be causing this? It seems to be random. The computer is not moving, and is only about 12 feet from the Home Hub with clear air in between. Is it likely to be the Home Hub which is causing the change, or the Mac? Is there anyway to "lock" the Homehub to only broadcast on N?
Thanks for any answers.

the only problem changing the BT Home hub 3 wireless channel manually it stops the new software from finding the best channel one of the features of the new hub. they advise this in the product page details (section taken shown below).What i found was to experiment hub positions my example i have 3 story house so i placed the hub on the second floor away from fridge /microwave/ wireless phone etc on the 1st floor. the wireless computers are on floor 2 & 3, it improved reception by 50%. the computer down on floor 1 is connected by ethernet.
Change wireless channel
Your Hub is always monitoring the wireless channel it’s using and if it detects too much
interference it will automatically change to another channel. If you want to manually
change to a channel of your choice, follow the steps below, but this will stop the
automatic channel selection feature.
1 Access Hub Manager by typing bthomehub.home into your web browser.
2 Click Settings.
3 If asked, enter your Hub Admin password. You’ll find this on the bottom of your Hub.
4 In the Basic Settings menu, click Change the wireless channel to avoid interference.
5 Click the Refresh button.
6 Wait a minute for your device to pick up the new channel.
http://btsupport.custhelp.com/ci/fattach/get/1893113/1296055445/redirect/1

Home hub dropping connection

New here so sorry if this is in the wrong place, or if I miss any information. I'll try to be as descriptive as possible.
I've had my bt infinity setup for around a month and a half. The home hub has been connected to an extention socket, and my computers are wired to the home hub.
This was working fine until two nights ago, when the home hub power light started flashing orange. There are no other lights showing on the home hub. The Internet was not working at all at this point, and my computer was saying that 'additional login information may be required'
When I open a browser I'm taken through the diagnostics, but it doesn't correspond exactly to the issue, as the broadband light is not also flashing on my home hub.
Last night I tried moving the home hub to the master socket. This appeared to work for a short time, but before long it was back to the exact same situation as the extention socket. The Internet works intermittently on the master socket.
According to bt there are no faults on the line. I have tried resetting the settings on my home hub also. I have tried calling bt but was on hold for quite a while to their technical team. Any help is much appreciated.

By using the test socket on the master socket, you should be removing ALL of the home wiring. This is to ensure your home wiring isn't the cause of your problems. Should the home wiring be the cause, then you would be charged for an engineer's visit, somewhere around £130 !!!
If you found this post helpful, then please click the star on the left, after all, I'm only trying to help........

BT Home Hub Manage Connections and Bandwidth.

Hello, I was wondering if it was possible to manage connections inside BT Home Hub. I am the owner of the hub and can log in to the advanced settings, I see I can turn the wireless off, is there a way to turn the wireless off for specific devices, but keep my laptop wireless on.
What about turning the internet off for specific wired devices, but keeping my computer on.
Third and final question, is there a way I can manage bandwidth useage?
So I can say to these devices, use 10% of bandwidth, and allow the rest to go to my computer.
Thanks, any information would be very helpful.

The simple answer to both your questions one and three is not with the HomeHub - and you might have difficulty finding a router designed for home use that will do both.
You should be able to restrict access to the internet on a machine by machine basis using the parental controls.
"To forbid us anything is to make us have a mind for it."
-- Michel de Montaigne, Essays, 1559

Infinty 2 & Home Hub 5 Connection Issue

Hi,
This afternoon our HH 5 lost wifi connection. My wife rang BT and a line/speed test was attempted, but wouldn't work.
After 50 minutes of attempting tests, a new Home Hub was ordered.
The lights on the hub go from orange to blue alternating with a orange steady broadband band light. Even when the light remains blue there is no internet connection.
I have carried out a reset, turned it off etc, all the usual stuff.but nothing. I have a fault reference but not sure if anything is being investigated. We rely on this connection for working, so this is very annoying. Currently connected to my mobile.

Hi,
The Hub has made no difference. We had a major fault in our local area. Since the connection has been repaired my speed has been very very poor.
Prior to the fault i was getting 40-50Mb normally. I am now getting 9Mb if I'm lucky, it fluctuates between 2-9Mb. When I am paying for the fastest service available this is pretty poor. My mobile signal is running at a download speed of 20Mb!
We have an engineer coming out on Monday, hopefully he will be able to help. The help desk have been little or no help at all. Firstly sending out a new router, when I had already told them that others in the area where experiencing issues, and they couldn't even carry out a line test. Then when I contacted then ref the slow speed, they asked if I had plugged my router in to the wall socket.....!
Wait and see what happens.

Samsung Galaxy Mini Home Hub 2 Connection Problem

My Galaxy Mini is connected to my home hub but I cannot access the internet.
I have other mobiles connected with no problems.
The phone is fine on other wifi connections.
Anyone have any idea whats wrong?

seafront123 wrote:
My Galaxy Mini is connected to my home hub but I cannot access the internet.
I have other mobiles connected with no problems.
The phone is fine on other wifi connections.
Anyone have any idea whats wrong?
Hmm, my lad also has the same phone with no issues connecting to my HH2 or HH3
(my hubs however are not set how they come delivered)
When it's connected to the hub, with the phone switched on, remove the battery, then re-insert and power up and then allow the phone to re-establish the connection.
(some phones can and do fail to 'talk' to your mobile operators servers, thus creating issues like this. rebooting should start the handshake process again)
Does it now connect?
Failing that you could adjust the hub's settings to something like this:
Change the hubs SSID (BTHomehub2-****) to something simple like hub2
Initially leave the wireless interface type at b/g/n (works for me) or just b/g
Try a different wireless channel - though the other devices would also be flaky
Try using just WPA2 (mines set to this) or just WPA
You could try changing the wireless key from it's default - though all other devices would then need to be reconnected.
Have you checked to see if it's up to date using Samsung Kies?
Hopefully any of the contributions above will cure it, if not I'm sure the guys on these forums will assist you further.
-+-No longer a forum member-+-

BT Home Hub not working with Airport Express

We have just moved house and had BT Internet installed. It uses the very latest Home Hub but this is causing the Airport Express to fail.
On occasion it works but more often than not the connect is lost and the MacBook/Airport Utility fail to see the AE's again.
What can I do to keep my Airport network up and running all the time. I NEVER used to have this problem with my old set up at my home house.

Whenever you make a change on your network.....in this case a new router......you need to reset the AirPort Express back to factory defaults and then reconfigure it again to work in the new environment.
Power down the AirPort Express
Hold in the reset button on the AirPort Express and keep holding it in for another 8-10 seconds as you plug the Express back in to power
Release the reset button
Allow 40-45 seconds for the AirPort Exrpess to restart
Open AirPort Utility and click Continue to follow the guided setup to configure the Express to "join" your wireless network.

Infinity 2 BT Home Hub 3 connection dropping issue...

Hello,
For over 2 months now I have been experiencing problems with our Home Hub 3 restarting and dropping the connection.
It car happen up to 6 times an hour or may be OK for up to 12 hours.
We have had 3 new HH3 routers, three engineer visits, numerous speed checks, line checks (all OK) and calls to 08001114567. As of today nothing has resolved the issue.
I have changed channel, have Openreach Modem & HH3 powered via a UPS, all connections have been checked and all leads changed. I have now lost all confidence in both Level 1 & Level 2 helpdesk. I am considering buying a non BT router to see if that overcomes the issues, but I don't see why I should have to, as I pay for a service from BT which I am not receiving.
Can anyone offer any advise.

HarrisonStephens infinity does not use ADSL filters just a filtered master socket installed by Openreach when infinity is installed
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

HP LaserJet 3030 printing gets "is not connected" message

When I send data to print, the printer appears to power off then restart with "Scanner Bulb warming up" message on the printer. Then I get a message on my computer that the printer is not connected.
This occurs with either a USB cable attached directly to my Macbook Pro, or the USB cable attached to an Apple modem with HandyPrint software installed. Either configuration was working previously. Somehow it just stopped.
Your assistance is greatly appreciated!

OK, can you go into your router settings to find what IP address it has given the printer? If you want help, let me know what brand/model of router you have.
Is there a way to get the IP address by reading it on the front panel of the printer?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

TP-Link TL-WA901 & Home Hub 5 connectivity problem

I've just installed a Home Hub 5. Devices connected via Ethernet & Wifi work fine. My Vista PC connected via a TP-Link switch & a TP-Link TL-WA901ND Wireless Access Point can't web browse successfully. Firefox says "The page isn't redirecting properly", IE says "Internet Explorer cannot display the webpage" - for every site I try. I can ping my BT hub OK, I can see the PC from the hub & a directly-connected Windows 7 PC, & I can ping external websites. Any ideas? I've tried changing all sorts of settings without any luck, Googled, etc, & nothing I've tried has sorted it. The same PC & browsers work if connected via Ethernet.
Btw, the connection setup is like this as I've had equipment damaged 3 times from lightning surges via my phone line. The PC connected directly is only temporary until I've resolved the problem.

This is from Keith's help pages. http://forumhelp.dyndns.info/hardware/TP_link/wa701nd/wa701nd.html
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Printer not connected message

I recently upgraded to Mountain Lion, and since then I am unable to print--I get the message "Printer Not Connected". My printer is connected to my Airport Extreme router via Ethernet cable. When I go to system preferences, then network, the firewire and the ethernet choices are red--as in not connected or not working. When I go to advanced, after choosing ethernet, I clicked on Renew DHCP Lease, but this doesn't change anything. Any help would be appreciated, because I use my printer all the time. It is a Canon Pixma MG8120.
Also, my Airport utility is saying "No configured Airport base stations have been found. Airport Utility will continue searching."

This is a common complaint after upgrading from Snow Leopard systems.
Try this - reset your printing system as described here:
http://support.apple.com/kb/HT1341
Choose System Preferences from the Apple menu.
Choose Print & Scan from the View menu.
Hold down the Option key while clicking the "-" (Remove printer) button. If no printers are currently added, hold down the Control key while clicking in the box that appears above the "+" (Add printer) button, then choose Reset printing system… from the contextual menu.
Then, add the Canon Pixma again using the "+" button.
What does Reset Printing System do?
Deletes all queues and jobs.
Resets all printer settings to their default by deleting configuration files.
Performs a permissions check on the /tmp directory.
Any printers, scanners, or fax modems that previously appeared in System Preferences will need to be added again after resetting the printing system.
That should fix it.

BT Home hub not connected message

Similar Messages

Maybe you are looking for